0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
DP-110-GRAY

DP-110-GRAY

  • 厂商:

    3M

  • 封装:

    -

  • 描述:

    GRAY EPOXY ADHESIVE 50ML

  • 数据手册
  • 价格&库存
DP-110-GRAY 数据手册
TM Scotch-Weld Epoxy Adhesive DP110 Translucent and Gray Technical Data March 2019 Product Description 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Translucent and Gray are two-part epoxy adhesives which combine a fast cure with flexibility. Features • Controlled flow • 20 minute handling strength • Duo-Pak cartridge dispensing system • Good adhesion to many plastics and metals Typical Uncured Physical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Product 3M Scotch-Weld Epoxy Adhesive DP110 Gray Viscosity @ 72°F (23°C), 73°F (24°C) (CPS) Base Accelerator 30,000 - 70,000 30,000 - 70,000 40,000 - 90,000 40,000 - 90,000 Base Resin Base Accelerator Modified Epoxy Amine Modified Epoxy Amine Color Base Accelerator Translucent White Light Yellow Net Weight (Lbs./Gallon) Base Accelerator 9.1 - 9.4 9.0 - 9.3 Whit e Black 9.1 - 9.4 9.0 - 9.3 Mix Ratio B:A Volume Weight 100 : 100 100 : 99 100 : 100 100 : 99 8 - 13 8 - 13 Worklife @ 73°F (24°C) (minutes) Typical Cured Physical Properties 3M Scotch-Weld Epoxy Adhesive DP110 Translucent Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Product Color Shore D Hardness (approx.) Elongation (approx.) 3M Scotch-Weld Epoxy Adhesive DP110 Translucent 3M Scotch-Weld Epoxy Adhesive DP110 Gray Yellow Translucent Gray 40 45 40% 40% 3M™ Scotch-Weld™ Epoxy Adhesives DP110 Translucent and Gray Typical Cured Thermal Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Product 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Translucent 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Gray Thermal Conductivity BTU/Hr/Ft2/°F/Ft. .106 @ 113°F (45°C) .104 @ 113°F (45°C) 80 x 10-6 200 x 10-6 73 x 10-6 165 x 10-6 55°F (13°C) 61°F (16°C) Thermal Coefficient of Expansion -58°F (-50°C) - 32°F (0°C) -58°F (-50°C) - 166°F (110°C) Glass Transition Temp. Typical Cured Electrical Properties Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Product 3M Scotch-Weld Epoxy Adhesive DP110 Translucent 3M Scotch-Weld Epoxy Adhesive DP110 Gray 520 470 4.5 x 1010 6.9 x 1010 Dielectric Strength (volts/mil) Volume Resistivity (ohms - cm) Typical Adhesive Performance Characteristics Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. The following product performance data was obtained in the 3M laboratory under the conditions specified. The following data show typical results obtained with Scotch-Weld epoxy adhesive DP110 Translucent and Gray when applied to properly prepared substrates and cured for 48 hours at 73°F (23°C) under 2 psi pressure and tested according to the specifications indicated. Note: All data developed after a 48 hour cure @ 75°F (24°C) under 2 psi pressure unless noted otherwise. A. Aluminum Overlap Shear Overlap shear strength was measured on FPL etched 1 in. wide by 1/2 in. overlap specimens. The bonds were made from 2 panels of 4 in. x 7 in. x .063 in., 2024 T3 clad aluminum bonded together and cut into 1 in. wide specimens. The separation rate of the testing jaws was .1 in./minute. Tests similar to ASTM D-1002. Test Temp 3M Scotch-Weld Epoxy Adhesive DP110 Translucent 3M Scotch-Weld Epoxy Adhesive DP110 Gray -67°F (-55°C) 75°F (24°C) 160°F (71°C) 180°F (82°C) 2500 psi 2500 psi 270 psi 200 psi 2700 psi 3500 psi 270 psi 250 psi -2- 3M™ Scotch-Weld™ Epoxy Adhesives DP110 Translucent and Gray Typical Adhesive Performance Characteristics (continued) Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. B. Aluminum T-Peel T-Peel bonds were measured on 1 in. wide specimens cut from two FPL etched 8 in. x 8 in. x .032 in., 2024 T3 clad aluminum panels bonded together. The separation note of the testing jaws was 20 in./minute. Tests similar to ASTM D-1876. Test Temp 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Translucent 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Gray 75°F (24°C) 20 piw 20 piw C. Overlap shear on abraded metals, plastics, and rubber Overlap shear strengths were measured on 1 in. wide 1/2 in. overlap specimens. These bonds were made individually using 1 in. x 4 in. pieces of substrate. The thickness of the substrates were: cold rolled, galvanized and stainless steel – 0.056-0.062 in., copper – 0.032 in., brass – 0.036 in., rubbers – 0.125 in., plastics – 0.125 in. All surfaces were prepared by solvent wiping/abrading/solvent wiping. The jaw separation rate used for testing was 0.1 in. per minute for metals, 2 in. per minute for plastics, and 20 in. per minute for rubbers. Overlap Shear (psi) @ 75°F (24°C) 3M Scotch-Weld Epoxy Adhesive DP110 Translucent 3M Scotch-Weld Epoxy Adhesive DP110 Gray 1000 1500 1500 1500 1500 1500 2300 2500 2450 2600 1750 2450 Styrene Butadiene Rubber/Steel Neoprene Rubber/Steel 80 - 100 40 - 60 80 - 100 40 - 60 ABS/ABS Plastic PVC/PVC, Rigid Polycarbonate/Polycarbonate Acrylic/Acrylic Fiber Reinforced Polyester/Fiber Reinforced Polyester 500 400 500 250 680 390 660 480 1400* 1400* Substrate Aluminum/Aluminum Cold Rolled Steel/Cold Rolled Steel Stainless Steel/Stainless Steel Galvanized Steel/Galvanized Steel Copper/Copper Brass/Brass *The substrate broke during the test instead of the bond. -3- Scotch-Weld TM Epoxy Adhesives DP110 Translucent and Gray Environmental Resistance Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Overlap shear specimens were prepared on aluminum as above and exposed to the environment conditions described below. Overlap Shear (psi) @ 75°F (24°C) Environment Initial 30 days tap water @ 75°F (24°C) 3 days, 160°F (71°C), 100% rel. humidity 14 days in 5% salt spray @ 95°F (35°C) 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Translucent 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Gray Etched Abraded Etched Abraded 2500 2300 1200 500 1000 1250 700 150 2500 2300 1200 500 2300 1250 700 150 Note: Avoid using either Scotch-Weld epoxy adhesive DP110 Translucent or Gray on metals where the bonded parts will experience high humidity/hot water conditions. User must test thoroughly adhesive performance for any environments which will be encountered. 3M™ EPX™ Pneumatic Applicator Delivery Rates 400 ml Applicator – Maximum Pressure 73 psi Adhesive* Scotch-Weld epoxy adhesive DP110 Gray Scotch-Weld epoxy adhesive DP110 Gray 100°F (38°C) 6mm Nozzle gms/minute 10mm Nozzle gms/minute 8.3 14.0 31.5 50.3 6.6 35.1 53.8 332.0 25.6 115.9 129.6 687.0** 200 ml Applicator – Maximum Pressure 58 psi Scotch-Weld epoxy adhesive DP110 Gray Scotch-Weld epoxy adhesive DP110 Gray 100°F (38°C) Scotch-Weld epoxy adhesive DP110 Gray 125°F (49°C) Scotch-Weld epoxy adhesive DP110 Gray 150°F (66°C) 48.5/50 ml Applicator – Maximum Pressure 50 psi 1/4 in. Nozzle gms/minute Adhesive* Scotch-Weld epoxy adhesive DP110 Translucent Scotch-Weld epoxy adhesive DP110 Gray 6.3 6.2 (nozzle cut back 2 divisions) 12.3 12.1 (nozzle cut back 2 divisions) *Tests were run at a temperature of 70°F ± 2°F (21°C ± 1°C) and at maximum applicator pressure. **Did not mix adequately. -4- 3M™ Scotch-Weld™ Epoxy Adhesives DP110 Translucent and Gray Handling/Curing Information Directions for Use 1. For high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed from substrates to be bonded. However, the amount of surface preparation necessary directly depends on the user’s required bond strength, environmental aging resistance and economic practicalities. For specific surface preparations on common substrates, see the section on surface preparation. 2. These products consist of two parts. Mixing For Duo-Pak Cartridges 3M™ Scotch-Weld™ Epoxy Adhesive DP110 Translucent and Gray are supplied in a dual syringe plastic duo-pak cartridge as part of the 3M™ EPX™ Applicator system. To use, simply insert the duo-pak cartridge into the EPX applicator and start the plunger into the cylinders using light pressure on the trigger. Next, remove the duo-pak cartridge cap and expel a small amount of adhesive to be sure both sides of the duo-pak cartridge are flowing evenly and freely. If automatic mixing of Part A and Part B is desired, attach the EPX mixing nozzle to the duo-pak cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of adhesive and mix thoroughly. Mix approximately 15 seconds after a uniform color is obtained. For Bulk Containers Mix thoroughly by weight or volume in the proportions specified on the product label or in the uncured properties section. Mix approximately 15 seconds after a uniform color is obtained. 3. For maximum bond strength apply product evenly to both surfaces to be joined. 4. Application to the substrates should be made within 8 minutes. Larger quantities and/or higher temperatures will reduce this working time. 5. Join the adhesive coated surfaces and allow to cure at 60°F (16°C) or above until completely firm. Heat up to 200°F (93°C), will speed curing. These products will fully cure in 48 hours @ 75°F (24°C). 6. Keep parts from moving during cure. Contact pressure necessary. Maximum shear strength is obtained with a 3-5 mil bond line. 7. Excess uncured adhesive can be cleaned up with ketone type solvents.* *Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use. Adhesive Coverage: A 0.005 in. thick bondline will typically yield a coverage of 320 sq. ft./gallon. -5- 3M™ Scotch-Weld™ Epoxy Adhesives DP110 Translucent and Gray Application Equipment Suggestions These products may be applied by spatula, trowel or flow equipment. Surface Preparation For high strength structural bonds, paint, oxide films, oils, dust, mold release agents and all other surface contaminants must be completely removed from substrate to be bonded. However, the amount of surface preparation necessary directly depends on the user’s required bond strength, environmental aging resistance and economic practicalities. The following cleaning methods are suggested for common surfaces: Two part mixing/proportioning/dispensing equipment is available for intermittent or production line use. These systems are ideal because of their variable shot size and flow rate characteristics and are adaptable to many applications. Steel: 1. Wipe free of dust with oil-free solvent such as acetone or isopropyl alcohol solvents.* 2. Sandblast or abrade using clean fine grit abrasives. 3. Wipe again with solvent to remove loose particles.* 4. If a primer is used, it should be applied within 4 hours after surface preparation. Aluminum: 1. Alkaline Degrease: Oakite 164 solution (9-11 oz./gallon water) at 190°F ± 10°F (88°C ± 23°C) for 10-20 minutes. Rinse immediately in large quantities of cold running water. 2. Acid Etch: Place panels in the following solution for 10 minutes at 150°F ± 5°F (66°C ± 23°C). Sodium Dichromate 4.1 - 4.9 oz./gallon Sulfuric Acid, 66°Be 38.5 o 41.5 oz./gallon 2024-T3 aluminum (dissolved) 0.2 oz./gallon minimum Tap water as needed to balance 3. Rinse: Rinse panels in clear running tap water. 4. Dry: Air dry 15 minutes; force dry 10 minutes at 150°F ± 10°F (66°C ± 23°C). 5. If primer is to be used, it should be applied within 4 hours after surface preparation. Plastics/Rubber: 1. Wipe with isopropyl alcohol.* 2. Abrade using fine grit abrasives. 3. Wipe with isopropyl alcohol.* *Note: When using solvents, extinguish all ignition sources, including pilot lights, and follow the manufacturer’s precautions and directions for use. -6- 3M™ Scotch-Weld™ Epoxy Adhesives DP110 Translucent and Gray Storage Store products at 60-80°F (16-27°C) for maximum storage life. Shelf Life These products have a shelf life of 24 months in their unopened original containers from date of manufacture. Precautionary Information Refer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501. Technical Information The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third party intellectual property rights is granted or implied with this information. Product Selection and Use Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property. Warranty, Limited Remedy, and Disclaimer Unless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability. ISO 9001: 2000 This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 standards Industrial Adhesives and Tapes Division 3M Center, Building 225-3S-06 St. Paul, MN 55144-1000 800-362-3550 • 877-369-2923 (Fax) 3M and Scotch-Weld are trademarks of 3M Company. ©3M 2019 78-6900-2827-5 www.3M.com/structuraladhesives -7-
DP-110-GRAY 价格&库存

很抱歉,暂时无法提供与“DP-110-GRAY”相匹配的价格&库存,您可以联系我们找货

免费人工找货