HM-H088FL1-8CS1-TG30

8 7 6 5 4 3 2 1 NOTES 3MTM HM PRESS-FIT HEADER, 8-ROW, HM SERIES * * * * FOR HARD METRIC APPLICATIONS * * * * D MODULAR/SCALABLE FORMAT IEC 61076-4-101 PRESS-FIT OF SOLDER TAIL VERSION 101 MATED LINES PER INCH SHIPS WITH PROTECTIVE CAP, WHICH ALSO SERVIES AS AN INSERTION TOOL END-TO-END STACKABLE WITH 8 ROW 3MTM HM AND HSHM PRODUCTS INTEGRATED GUIDE AND GUIDE PIN MULTI-PURPOSE CENTER (MPC) KEYING AND GUIDANCE FOUR INTEGRATED 8.25 A POWER CONTACTS AND GUIDE PIN 1. MATERIAL: PLASTIC: HIGH TEMP LCP, UL94V-0 PINS: COPPER ALLOY. 2. REGULATORY INFORMATION: ROHS COMPLIANT. SEE THE REGULATORY INFORMATION APPENDIX (RIA) IN THE "ROHS COMPLIANCE" SECTION OF WWW.3MCONNECTORS.COM FOR COMPLIANCE INFORMATION (RIA E1 & C1 APPLY) D 3 IN THE EVENT OF CONFLICT BETWEEN THIS DATA AND THAT CONTAINED IN THE PRODUCT SPECIFICATION, THE PRODUCT SPECIFICATION TAKES PRECEDENT. HM-H200DE1-8CX1 HM-H244DE2-8BX1 HM-H200E1-8CX1 HM-H244E2-8BX1 HM-H176D1-8CX1 HM-H220D2-8BX1 3 MECHANICAL: NORMAL FORCE (NOMINAL): ENGAGEMENT FORCE (NOMINAL): SEPARATION FORCE (NOMINAL): WIPE (NOMINAL, SHORTEST CONTACT): MATE/UNMATE CYCLES: APPLICATION: C 3 .57N [58g] SIGNAL .32N [33g] SIGNAL .20N [20g] SIGNAL 2.67 [.105] SIGNAL 250 THIS MODULE IS NOT SUITABLE FOR STAND-ALONE USE. (REFER TO IEC-61076-4-101) C ELECTRICAL: CURRENT RATING (FULLY LOADED): 1A @ 70 C SIGNAL INSULATION RESISTANCE: 1 X 104 MO @ 100 VDC WITHSTANDING VOLTAGE: 750VRMS HM-H176DPWR1-8CX1 HM-H220DPWR2-8BX1 HM-H088FL1-8CX1 HM-H110FL2-8BX1 HM-H088FR1-8CX1 HM-H110FR2-8BX1 (UNLESS OTHERWISE SHOWN) (UNLESS OTHERWISE SHOWN) ORDERING INFORMATION ORDERING INFORMATION (ROWS I AND Z NOT LOADED) (ROWS I AND Z LOADED, 8.3MM MATE LENGTH) HM-HXXXXX1-8CX1-XXXXX HM-HXXXXX2-8BX1-XXXXX B HEADER POSITION AND TYPE PLATING HEADER POSITION AND TYPE TAIL STYLE: P = PRESS-FIT TAIL S = SOLDER TAIL 78-5100-2517-0 HM-H176DG1-8CX1 HM-H220DG2-8BX1 A TEMPERATURE RATING: -55 C TO 125 C PROCESS RATING: MAX. 260 C (PER J-STD-020C) WITHSTANDING VOLTAGE: 1 (PER J-STD-020C) REVISION ENVIRONMENTAL: DRAWING NUMBER 3 B PLATING TAIL STYLE: P = PRESS-FIT TAIL S = SOLDER TAIL PLATING SPECIFICATIONS: TG30L = .76 M [30 IN] MIN. GOLD ON CONTACT AREA, LUBRICATED 2.54 M [100 IN] MIN. TIN/LEAD ON TERMINAL AREA (RIA C2 & E2 APPLY) 1.27 M [50 IN] MIN. NICKEL ALL OVER. TYPICALLY HIGHER MAKE ORDER QUANTITIES AS COMPARED TO TG30. DIMENSIONS: MM [INCHES] TG50 = 1.27 M [50 IN] MIN. GOLD ON CONTACT AREA, LUBRICATED 2.54 M [100 IN] MIN. TIN/LEAD ON TERMINAL AREA (RIA C2 & E2 APPLY) 1.27 M [50 IN] MIN. NICKEL ALL OVER. NON-STANDARD OPTION (AVAILABLE WITH LONGER LEAD TIMES AND HIGHER MAKE ORDER QUANTITIES, MOQ) 3MTM ELECTRONIC SOLUTIONS DIVISION INTERCONNECT SOLUTIONS http://www.3mconnectors.com KR = .76 M [30 IN] MIN. GOLD ON CONTACT AREA 2.54 M [100 IN] MIN. MATTE TIN ON TERMINAL AREA (RIA C2 & E2 APPLY) 1.27 M [50 IN] MIN. NICKEL ALL OVER. 3M IS A TRADEMARK OF 3M COMPANY. FOR TECHNICAL, SALES OR ORDERING INFORMATION CALL 800-225-5373 8 DESIGN REFERENCE NEXT ASSEMBLY DISTRIBUTION CODES DIVISION 6 5 4 MAR 28,2012 Interconnect Solutions DO NOT SCALE DRAWING R 3 ECO ISSUE DATE AND DESCRIPTION DRFT DATE CASTIGLIONE MAR 28,2012 CHKD DATE C ISD 3M Center St. Paul, TOLERANCES EXCEPT AS NOTED SCALE 5 2 THIRD ANGLE PROJECTION INTERPRET PER ASME Y14.5 - 1994 UL FILE NO: E68080 REV DIVISION CODE MAX SURFACE ROUGHNESS ALL SURFACES MARKED ONLY 7 39815 JNC TS DRFT CHKD PRODUCTION RELEASE TG30 = .76 M [30 IN] MIN. GOLD ON CONTACT AREA 2.54 M [100 IN] MIN. TIN/LEAD ON TERMINAL AREA (RIA C2 & E2 APPLY) 1.27 M [50 IN] MIN. NICKEL ALL OVER. STANDARD OPTION. A A 2 INCHES .0 .00 .01 .000 .005 .0000 MILLIMETERS 0 .0 .3 .00 .13 .000 ANGLES MN 55144 MFG DATE APPVL DATE T. SUNIGA MAR 28,2012 3M COPYRIGHT 2012 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE HM PRESS-FIT HEADER, 8-ROW, HM SERIES CAGE SIZE NUMBER MODEL DRAWING NO. REV. 78-5100-2517-0 DET. LISTS 1 YES NO A SHT 1 OF 4 A 8 7 6 5 4 3 2 1 NOTES TM 3M 1 CAPS TO BE REMOVED AFTER PRESS-FIT INSTALLATION PROCESS. HM PRESS-FIT HEADER, 8-ROW, HM SERIES FOR HARD METRIC APPLICATIONS 49.85 1.963 49.85 1.963 48.00 1.890 48.00 1.890 2.00 .079 2.00 .079 2.00 .079 D D 2.00 .079 ROW I ROW I ROW H ROW H ROW G ROW G ROW F 18.00 ROW E .709 ROW D ROW F 18.00 ROW E .709 ROW D ROW C ROW C ROW B ROW B ROW A ROW A ROW Z ROW Z 1 2 3 4 5 6 7 8 2.00 .079 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 2.00 .079 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PIN POSITIONS PIN POSITIONS 2.00 .079 1.50 .059 2.00 .079 4.50 17.85 1.50 .059 .177 4.50 17.85 .703 .177 .703 C C REV X HM-H200E1-8CX1 HM-H244E2-8BX1 .596 XXYY A HM-H200DE1-8CX1 HM-H244DE2-8BX1 49.85 1.963 48.00 1.890 2.00 .079 2.00 .079 B 1 21.40 .843 PROTECTIVE CAP B ROW I SIGNAL CONTACTS ROW H ROW G REVISION .596 XXYY 78-5100-2517-0 REV X 15.15 HM-HXXXXX-8XXX-XXXXX DRAWING NUMBER 15.15 HM-HXXXXX-8XXX-XXXXX 5.00 .197 ROW F 18.00 ROW E .709 ROW D DIM. "A" MATE LENGTH ROW C ROW B 13.40 ROW A ROW Z .528 1 2 3 4 5 6 7 8 2.00 .079 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PIN POSITIONS 2.00 .079 1.50 .059 4.50 15.60 DIM. "B" TAIL LENGTH .177 .614 15.15 HM-HXXXXX-8XXX-XXXXX REV X A TYPICAL SIDE VIEW DIMENSIONS FOR THE HEADERS ON THIS DRAWING A DESIGN REFERENCE NEXT ASSEMBLY DISTRIBUTION CODES DIVISION DO NOT SCALE DRAWING DIM. "A" 5.3 [.21] FOR ROWS A THRU H DIM. "B" 4.4 [.17] EXCEPT AS NOTED HM-H176D1-8CX1 HM-H220D2-8BX1 FOR NON-STANDARD CONFIGURATIONS CONTACT A 3M SALES REPRESENTATIVE 3 1 THIRD ANGLE PROJECTION INTERPRET PER ASME Y14.5 - 1994 MAX SURFACE ROUGHNESS MARKED ONLY 7 6 5 4 3 ECO ISSUE DATE AND DESCRIPTION DRFT DATE CASTIGLIONE MAR 28,2012 CHKD DATE C ISD 3M Center St. Paul, TOLERANCES EXCEPT AS NOTED SCALE ALL SURFACES 8 REV DIVISION CODE Interconnect Solutions STANDARD CONFIGURATION MAR 28,2012 JNC TS DRFT CHKD PRODUCTION RELEASE .596 XXYY 39815 2 INCHES .0 .00 .01 .000 .005 .0000 MILLIMETERS 0 .0 .3 .00 .13 .000 ANGLES MN 55144 MFG DATE APPVL DATE T. SUNIGA MAR 28,2012 3M COPYRIGHT 2012 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE HM PRESS-FIT HEADER, 8-ROW, HM SERIES CAGE SIZE NUMBER MODEL DRAWING NO. REV. 78-5100-2517-0 DET. LISTS 1 YES NO A SHT 2 OF 4 A 8 7 6 5 4 3 2 1 3MTM HM PRESS-FIT HEADER, 8-ROW, HM SERIES FOR HARD METRIC APPLICATIONS 49.85 1.963 49.85 1.963 48.00 1.890 48.00 1.890 2.00 .079 2.00 .079 D 2.00 .079 2.00 .079 D P1 P2 ROW I ROW I ROW H ROW H ROW G ROW G ROW F ROW F 18.00 ROW E .709 ROW D .709 ROW D 18.00 ROW E ROW C ROW C ROW B ROW B ROW A ROW A ROW Z ROW Z 1 2 3 4 5 6 7 8 2.00 .079 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 P3 P4 PIN POSITIONS PIN POSITIONS 15.60 2.00 .079 15 16 17 18 19 20 21 22 23 24 25 2.00 .079 16.72 2.00 .079 .614 ESD PIN .658 1.50 .059 1.50 .059 4.50 4.50 .177 .177 C 24.00 C 24.00 .945 .945 15.15 HM-HXXXXX-8XXX-XXXXX REV X .596 XXYY 15.15 HM-HXXXXX-8XXX-XXXXX REV X .596 XXYY 24.92 .981 24.92 .981 20.00 .787 20.00 .787 2.00 .079 A DIM. "B" TAIL LENGTH 1 = 4.4 [.17] PIN, 2.0 [.08] POWER AND 2.0 [.08] ESD 2 = 4.4 [.17] PIN, 4.4 [.17] POWER AND 2.0 [.08] ESD 2.00 .079 2.00 .079 B ESD PIN TAIL LENGTH 2.00 .079 ROW I ROW I ROW H ROW H ROW G ROW G ROW F ROW C ROW B ROW B ROW A ROW A ROW Z ROW Z 2 3 4 5 6 7 8 2.00 .079 9 10 11 .709 ROW D ROW C 1 18.00 ROW E .709 ROW D B ROW F 18.00 ROW E DRAWING NUMBER HM-H176DPWR1-8CXX HM-H220DPWR2-8BXX POWER TAILS (4 CONTACTS, 12 LEADS) 78-5100-2517-0 HM-H176DG1-8CX1 HM-H220DG2-8BX1 REVISION 2.00 .079 1 PIN POSITIONS 2 3 4 5 6 7 8 2.00 .079 9 10 11 PIN POSITIONS 2.00 .079 1.50 .059 2.00 .079 1.50 .059 4.50 15.00 4.50 15.00 .177 .591 .177 A .591 39815 MAR 28,2012 JNC TS DRFT CHKD PRODUCTION RELEASE DESIGN REFERENCE 15.15 HM-HXXXXX-8XXX-XXXXX A REV X HM-HXXXXX-8XXX-XXXXX .596 XXYY NEXT ASSEMBLY DISTRIBUTION CODES REV X 15.15 .596 XXYY DIVISION HM-H088FR1-8CX1 HM-H110FR2-8BX1 3 1 INTERPRET PER ASME Y14.5 - 1994 MAX SURFACE ROUGHNESS ALL SURFACES MARKED ONLY 8 7 6 5 4 3 ISSUE DATE AND DESCRIPTION DATE CASTIGLIONE MAR 28,2012 CHKD DATE C ISD 3M Center St. Paul, TOLERANCES EXCEPT AS NOTED SCALE THIRD ANGLE PROJECTION HM-H088FL1-8CX1 HM-H110FL2-8BX1 ECO DRFT DIVISION CODE Interconnect Solutions DO NOT SCALE DRAWING REV 2 INCHES .0 .00 .01 .000 .005 .0000 MILLIMETERS 0 .0 .3 .00 .13 .000 ANGLES MN 55144 MFG DATE APPVL DATE T. SUNIGA MAR 28,2012 3M COPYRIGHT 2012 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE HM PRESS-FIT HEADER, 8-ROW, HM SERIES CAGE SIZE NUMBER MODEL DRAWING NO. REV. 78-5100-2517-0 DET. LISTS 1 YES NO A SHT 3 OF 4 A 8 7 6 5 4 3 2 1 NOTES HM PRESS-FIT HEADER, 8-ROW, HM SERIES FOR HARD METRIC APPLICATIONS B D DIM. "D" .10 A B PLATED THRU HOLES 18.00 18.00 .709 .709 2.00 18.00 .709 25 25 24 24 23 23 22 22 21 21 20 20 19 19 18 18 17 17 16 16 15 15 1.890 9 9 8 8 7 7 6 6 5 5 4 4 3 3 G F E D C B A I H G F E D C B A .079 +.002 -.000 20 HM-H200E1-8CX1 HM-H244E2-8BX1 A B 21 20 +.002 -.000 19 18 4.00 .10 A B .157 15 .10 11 10 10 4.00 8 A B Z 12 11 9 +.002 -.001 13 1.890 12 .093 14 48.00 13 +.05 2.35 -.03 8 .157 7 7 6 6 5 5 4 4 3 3 H G F E D C B A 2 A 1 I 4.00 9 2 A .157 16 14 OUTLINE OF HEADER 4.00 17 15 1.890 1 Z I 2.00 .079 H G F E D C B A C .157 DIM. "D" .10 A B PLATED THRU HOLES Z 2.00 .079 18.00 .709 HM-H176D1-8CX1 HM-H220D2-8BX1 B 12.00 .472 2.00 .079 2.00 5.00 .197 4X 1 +.05 .00 1 B 18.00 .709 +.002 .079 -.000 1.50 .059 HM-H176DG1-8CX1 HM-H220DG2-8BX1 78-5100-2517-0 A 1 22 18 48.00 HM-H200DE1-8CX1 HM-H244DE2-8BX1 1 .079 19 .10 23 +.05 2.00 .00 21 2.00 .079 2.00 .079 24 22 1 Z 24 23 2 A 25 16 10 .079 25 12 10 1 2.00 .079 +.05 2.00 .00 DIM. "D" .10 A B PLATED THRU HOLES D 6.00 .236 2.00 17 11 2 DIM. "D" .10 A B PLATED THRU HOLES 13 11 A B 6.00 .236 14 48.00 12 C 12.00 .472 .079 13 1.890 18.00 .709 B 2.00 14 48.00 H ROW I AND Z HOLES ARE ONLY USED FOR HM-HXXXX2-8BX1 STYLE HEADER. B .079 I 1 18.00 .709 B 25 B .10 24 A B 6.00 .236 23 DIM. "D" .10 A B PLATED THRU HOLES 232X 22 21 DIM. "B" .05 A B PLATED THRU HOLE 1X 20 19 3.00 2X 17 11 11 2.00 .079 14 8 13 7 20.00 6 .787 11 5 10 23.90 4 9 .941 3 8 A 22.10 6 5 2.00 .079 1 G F E D C B A I H G F E D C B A 2.00 A 5 .079 4 +.002 -.000 3 .10 2 A B 1 2.00 .079 I H G F E D C B A Z A 3.00 .118 HM-H088FR1-8CX1 HM-H110FR2-8BX1 1 DESIGN REFERENCE NEXT ASSEMBLY DISTRIBUTION CODES 1 DIVISION 1.50 .059 RECOMMENDED PCB MOUNTING HOLE PATTERN (VIEWED FROM COMPONENT SIDE) 3 1 THIRD ANGLE PROJECTION INTERPRET PER ASME Y14.5 - 1994 MAX SURFACE ROUGHNESS MARKED ONLY 7 6 5 4 3 REV ECO ISSUE DATE AND DESCRIPTION DRFT DATE CASTIGLIONE MAR 28,2012 CHKD DATE C ISD 3M Center St. Paul, TOLERANCES EXCEPT AS NOTED SCALE ALL SURFACES 8 MAR 28,2012 DIVISION CODE Interconnect Solutions DO NOT SCALE DRAWING 1 39815 JNC TS DRFT CHKD PRODUCTION RELEASE Z HM-H176DPWR1-8CXX HM-H220DPWR2-8BXX +.05 .00 6 Z HM-H088FL1-8CX1 HM-H110FL2-8BX1 2 H .787 7 A 1 3 I 8 .870 4 A DIM. "D" .10 A B PLATED THRU HOLES 20.00 2 7 .945 9 9 12 2.00 .079 2.00 .079 2.00 .079 .118 10 15 24.00 B 6.00 .236 10 16 1.890 DIM. "D" .10 A B PLATED THRU HOLES 18 48.00 REVISION 3M HOLE PLATING TABLE HOLE (FINISHED HOLE) Cu THICKNESS SnPb THICKNESS DRILLED HOLE DIA. DIM. "B" .690-.790 [.0270-.0310] .025-.045 [.0010-.0018] .008-.018 [.0003-.0007] .810-.860 [.0320-.0340] DIM. "D" .550-.650 [.0217-.0256] .025-.045 [.0010-.0018] .008-.018 [.0003-.0007] .686-.727 [.0270-.0286] DRAWING NUMBER TM 2 INCHES .0 .00 .01 .000 .005 .0000 MILLIMETERS 0 .0 .3 .00 .13 .000 ANGLES MN 55144 MFG DATE APPVL DATE T. SUNIGA MAR 28,2012 3M COPYRIGHT 2012 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE HM PRESS-FIT HEADER, 8-ROW, HM SERIES CAGE SIZE NUMBER MODEL DRAWING NO. REV. 78-5100-2517-0 DET. LISTS 1 YES NO A SHT 4 OF 4 A