HM-H200DE1-8CP1-TG30

3M™ MetPak™ HM Header 2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight HM Series • • • • • Modular/scalable format IEC 61076-4-101 Press-fit headers or solder tail version 101 mated lines per linear inch Integrated guide Ships with protective cap, which also serves as an insertion tool • End-to-end stackable with 8 row 3M™ MetPak™ HM and HSHM products • See Regulatory Information Appendix (RIA) for chemical compliance information Date Modified: April 4, 2007 TS-2070-03 Sheet 1 of 3 Physical Insulation Material: High Temperature Thermoplastic (LCP) Flammability: UL 94V-0 Contact Material: Copper Alloy Plating: See Ordering Information Marking: 3M Logo, Part Number, Revision, Date Code Performance Mechanical Normal Force (Nominal): 0.57 N [ 58 g ] Signal Engagement Force (Nominal): 0.32 N [ 33 g ] Signal Separation Force (Nominal): Wipe (Nominal, Shortest Contact): Durability: Application: Electrical Current Rating (Fully Loaded): 0.20 N [ 20 g ] Signal 2.67 mm [ 0.105 in. ] Signal 250 cycles with TR40B plating (Lubricated) This module is not suitable for stand-alone use. 1 A at 70° C Signal Insulation Resistance: 1 x 104 MΩ at 100 VDC Withstanding Voltage: 750 VRMS Environmental Temperature Rating: -55°C to +125°C Process Rating: Maximum 260°C (per J-STD-020C) Moisture Sensitivity Level: 1 (per J-STD-020C) UL File No.: E68080 3M Interconnect Solutions http://www.3M.com/interconnects/ MetPak is a trademark of 3M Company. 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ HM Header 2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight mm 2.00 .079 Tolerance Unless Noted mm 49.85 1.963 2.00 .079 [inch] 0 0.0 0.00 ±3 ±0.3 ±0.13 HM Series 2.00 .079 Pin positions 1 2 3 4 5 6 7 8 9 2.00 .079 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ROW I ROW H ROW G [ ] Dimensions for Reference Only ROW F ROW E 18.00 .709 ROW D ROW C ROW B ROW A ROW Z 48.00 1.890 21.40 .843 17.85 .703 Signal Contacts 5.00 .197 1.50 .059 4.50 .177 HM-HXXXXX-8XPX-XXXXX 13.40 .528 DIM A REV X 15.15 .596 XXYY DIM B DIM A = Pin mating length DIM B = Pin tail length Shown with protective caps* * Caps to be removed after press-fit installation process Ordering Information HM - H200DE1 - 8CX1 - XXXXX HM - H244DE2 - 8BX1 - XXXXX Tail Style: P =Press-fit tail S =Solder tail (rows I and Z not loaded) (rows I and Z loaded 8.3 mm mate length) Plating Options: (See Plating Table) Standard configuration DIM A = 5.3 mm for rows A through H DIM B = 4.4 mm For non-standard configurations contact sales representative TS-2070-03 Sheet 2 of 3 3M Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ HM Header 2 mm Type DE, 200 Signal Contacts, 8 Rows, Straight HM Series 2.00 2.00 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 O DIM. "D" l O 0.10 M A B Plated thru holes See hole plating table I 48.00 A H G F E D C B A Z 18.00 B Recommended PCB hole mounting pattern H O LE PLATING TAB LE FINIS H ED H O LE DIA. "D" C u TH IC KNES S S n Pb TH IC KNES S DRILLED H O LE DIA. 0.550-0.650 [.021 7-.0256 ] 0.025-0 .045 [.0 010-.0 018] 0.00 8-0.01 8 [.0003-.0007] 0.686-0.727 [.0270-.0286] Pla ting Suffix Pre ss-Fit Te rm ina tions TG30 (RIA E2 & C2 a pply) TR40B (RIA E2 & C2 a pply) Pla ting Cha rt Solde r Ta il Te rm ina tions Pla ting Com position (RIA E3 & C2 a pply) 0.76 µm [30 µ"] Min. Au Conta ct Are a 2.54 µm [100 µ"] Min. SnPb Ta il Are a 1.27 µm [50 µ"] Min. Ni a ll ove r (RIA E3 & C2 a pply) 0.127 µm [5 µ"] Min. Ha rd Au ove r 1.02 µm [40 µ"] Min. Pd/Ni ove r 0.10 µm [4 µ"] Min. Pd Strike Conta ct Are a 2.54 µm [100µ"] Min SnPb Te rm ina l Are a 1.27 µm [50 µ"] Min. Ni a ll ove r (Lubrica te d Conta ct Are a ) TS-2070-03 Sheet 3 of 3 3M Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/17/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. RIA-2217-B CHINA Appendix C1: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS 20 Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. Name and Content of Hazardous Substances or Elements Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 800/225-5373 www.3M.com/interconnects RIA-2217-B © 3M 2007