HSHM-H125B4-5CP1-TR40B

3M™ MetPak™ HSHM Press-Fit Header 2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight HSHM Series • • • • • • Up to 5 Gb/s data rates Low crosstalk at high frequencies 50/100 Ω (single-ended /differential) impedance Modular/scalable format IEC 61076-4-101 63 mated lines per linear inch End-to-end stackable with 5 row 3M™ MetPak™ CP2, HM and HSHM headers • See Regulatory Information Appendix (RIA) for chemical compliance information Date Modified: March 27, 2007 TS-2064-02 Sheet 1 of 3 Physical Insulation Material: High Temperature Thermoplastic (LCP) Flammability: UL 94V-0 Contact Material: Copper Alloy Plating: See Ordering Information Performance Mechanical Normal Force (Nominal): 0.57 N [ 58 g ] Signal, 0.74 N [ 75 g ] Shield Engagement Force (Nominal): 0.32 N [ 33 g ] Signal, 0.22 N [ 22 g ] Shield Separation Force (Nominal): Wipe (Nominal, Shortest Contact): Durability: Application: Electrical Data Rate: Characteristic Impedance: Current Rating (Fully Loaded): 0.20 N [ 20 g ] Signal, 0.20 N [ 20 g ] Shield 2.67 mm [ 0.105 in. ] Signal, 1.57 mm [ 0.062 in ] Shield 250 cycles with TR40B plating This module is not suitable for stand-alone use, (Refer to IEC-61076-4-101) 5 Gb/s 50 Ω Single-ended, 100 Ω Differential 1 A at 70° C Signal Insulation Resistance: 104 MΩ at 100 VDC Withstanding Voltage: 750 VRMS Environmental Temperature Rating: -55°C to +125°C UL File No.: E68080 3 Interconnect Solutions http://www.3M.com/interconnects/ MetPak is a trademark of 3M Company. 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ HSHM Press-Fit Header 2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight HSHM Series 49.85 1.963 2.00 .079 2.00 .079 1 2 3 4 5 6 Pin positions 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 ROW F 2.00 .079 2.00 .079 ROW E 12.00 .472 ROW D ROW C ROW B ROW A ROW Z 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Shield positions 48.00 1.890 15.40 .606 Interstitial ground contacts denotes shield column (tail only) omitted for the row differential pair part 5.00 .197 1.50 .059 Signal contacts 4.50 .177 DIM A DIM C DIM B 4.50 .177 HSHM-HXXXXX-5XPX-XXXXX 13.40 .528 REV X 15.15 .596 XXYY Coaxial, column differential and stripline configuration shown with protective caps* DIM A = Pin mating length DIM B = Shield tail length DIM C = Pin tail length mm HSHM-HXXXXX-5XPX-XXXXX [inch] REV X XXYY Tolerance Unless Noted mm 0 0.0 0.00 ±3 ±0.3 ±0.13 [ ] Dimensions for Reference Only Row differential configuration shown with protective caps* Standard Configuration DIM A = 5.3 mm for rows A through E * Caps to be removed after press-fit installation process For non-standard configurations contact sales representative Ordering Information HSHM - H125BX - 5CPX - XXXXX High Speed Option: 4 =Coaxial, column differential and stripline (75 Ω) applications 5 =Row differential applications Tail Length: 1 =4.4 mm pin and 3.5 mm shield 2 =2 mm pin and 2 mm shield (rows F and Z not loaded) Plating μm [ μ″ ]: TG30 = 0.76 [ 30 ] Min. Au Contact Area 2.54 [ 100 ] Min. SnPb Terminal Area (RIA E2 & C2 apply) 1.27 [ 50 ] Min. Ni All over TR40B = 0.127 [ 5 ] Min. Hard Au Contact Area, Lubricated 1.02 [ 40 ] Min. PdNi Contact Area 0.10 [ 4 ] Min. Pd Strike Contact Area 2.54 [ 100 ] Min. SnPb Terminal Area (RIA E2 & C2 apply) 1.27 [ 50 ] Min. Ni all over TS-2064-02 Sheet 2 of 3 3 Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ HSHM Press-Fit Header 2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight HSHM Series 2.00 1.00 1.00 2.00 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 O DIM D l O 0.10 M A B Plated thru holes E D C B A 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 48.00 A E D C B A 8.00 B Recommended PCB hole mounting pattern for coaxial, column differential and stripline applications Recommended PCB hole mounting pattern for row differential applications (Same geometry as left view without the ground vias) FINISHED HOLE DIA. ("D") 0.457 - 0.559 [.0180 - .0220] HOLE PLATING TABLE mm [in.] Cu. THICKNESS SnPb THICKNESS 0.025 - 0.045 [.0010 - .0018] 0.008 -0.018 [.0003 - .0007] DRILLED HOLE DIA. 0.584 - 0.625 [.0230 - .0246] TS-2064-02 Sheet 3 of 3 3 Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/17/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. RIA-2217-B CHINA Appendix C1: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS 20 Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. Name and Content of Hazardous Substances or Elements Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 800/225-5373 www.3M.com/interconnects RIA-2217-B © 3M 2007