HSHM-H125B4-5CP2-TG30 数据手册
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight
HSHM Series
•
•
•
•
•
•
Up to 5 Gb/s data rates
Low crosstalk at high frequencies
50/100 Ω (single-ended /differential) impedance
Modular/scalable format IEC 61076-4-101
63 mated lines per linear inch
End-to-end stackable with 5 row 3M™ MetPak™ CP2,
HM and HSHM sockets
• See the Regulatory Information Appendix (RIA) in
the “RoHS compliance” section of
www.3mconnector.com for compliance information
Date Modified: March 28, 2011
TS-2064-C
Sheet 1 of 3
Physical
Insulation Material: High Temperature Thermoplastic (LCP)
Flammability: UL 94V-0
Contact
Material: Copper Alloy
Plating: See Ordering Information
Performance
Mechanical:
Normal Force (Nominal): 0.57 N [58 g] Signal, 0.74 N [75 g] Shield
Engagement Force (Nominal): 0.32 N [33 g] Signal, 0.22 N [22 g] Shield
Separation Force (Nominal): 0.20 N [20 g] Signal, 0.20 N [20 g] Shield
Wipe (Nominal, Shortest Contact): 2.67 mm [0.105 in] Signal, 1.57 mm [0.062 in] Shield
Mate/Unmate Cycles: 250
Application: This module is not suitable for stand-alone use. (Refer to IEC-61076-4-101)
Electrical:
Data Rate: 5 Gb/s
Characteristic Impedance: 50 Ω Single-ended, 100 Ω Differential
Current Rating (Fully Loaded): 1 A @ 70°C Signal
Insulation Resistance: 104 MΩ @ 100 VDC
Withstanding Voltage: 750 Vrms
Environmental
Temperature Rating: -55° C to 125° C
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
MetPak is a trademark of 3M Company.
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight
49.85
1.963
2.00
.079
mm
0
±3
2.00
.079
1
mm
(Inch)
Tolerance Unless Noted
HSHM Series
2
3
4
5
6
Pin positions
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
ROW F
2.00
.079
2.00
.079
ROW E
12.00
.472
0.0 0.00
±0.3 ±0.13
ROW D
ROW C
ROW B
ROW A
[ ] Dimensions for
Reference Only
ROW Z
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Shield positions
48.00
1.890
15.40
.606
Interstitial
ground
contacts
denotes shield column (tail only) omitted for the row
differential pair part
5.00
.197
1.50
.059
Signal
contacts
4.50
.177
DIM A
DIM C
DIM B
13.40
.528
4.50
.177
HSHM-HXXXXX-5XPX-XXXXX
REV X
15.15
.596
XXYY
Coaxial, column differential and stripline configuration
shown with protective caps*
DIM A = Pin mating length
DIM B = Shield tail length
DIM C = Pin tail length
HSHM-HXXXXX-5XPX-XXXXX
REV X
Standard Configuration
DIM A = 5.3 mm for rows A through E
For non-standard configurations
contact sales representative
XXYY
Row differential configuration
shown with protective caps*
* Caps to be removed after press-fit installation process
Ordering Information
HSHM-H125BX - 5CP1- XXXXX
High Speed Option:
4 =Coaxial, column differential and
stripline (75 Ω) applications
5 =Row differential applications
Tail Length:
1 =4.4 mm pin and 3.5 mm shield
2 =2 mm pin and 2 mm shield
(rows F and Z not loaded)
Plating μm [ μ” ]:
TG30 = 0.76 [30] Min. Au Contact Area
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Standard Option
TG30L =
0.76 [30] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Typically higher make order quantities as compared to TG30.
TG50 =
1.27 [50] Min. Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
TS-2064-C
Sheet 2 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type B25, 125 Signal Contacts, 5 Rows, Straight
HSHM Series
2.00
1.00
1.00
2.00
Ø DIM D
M A B
Ø 0.10
Plated thru holes
E D C B A
8.00
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
48.00
A
E D C B A
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
B
Recommended PCB hole mounting pattern for coaxial, column
differential and stripline applications
Recommended PCB hole mounting pattern for row
differential applications
(Same geometry as left view without the ground vias)
Hole Plating Table mm [in.]
Finsihed Hole Dia. “D”
Cu. Thickness
SnPb Thickness
Drilled Hole Dia.
0.457 - 0.559 [.0180 - .0220]
0.025 - 0.045 [.0010 - .0018]
0.008 -0.018 [.0003 - .0007]
0.584 - 0.625 [.0230 - .0246]
TS-2064-C
Sheet 3 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
HSHM-H125B4-5CP2-TG30 价格&库存
很抱歉,暂时无法提供与“HSHM-H125B4-5CP2-TG30”相匹配的价格&库存,您可以联系我们找货
免费人工找货