3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin
MP2 Series
Solder Tail
• End-to-end stackable
• Select load capability
• Monoblockable
• Shoulder Pin
Press Fit
• End-to-end stackable
• Early mate late break for hot swapping (press-fit EMLB
adjusted by application tooling)
• Select load capability
• Monoblockable
• Push-on shoulder pin
• Optional feed-through tail for rear plug-up midplane
applications
• Accepts Universal Tooling
• RoHS Compliant. See the Regulatory Information
Appendix (RIA) in the “RoHS compliance” section of
www.3M.com/Interconnects for compliance information
(RIA E1 & C1 apply)
Date Modified: September 9, 2009
TS-1120-C
Sheet 1 of 4
Physical
Insulation:
Material: High Temp LCP
Flammability: UL 94V-0
Color: Beige
Color:
Material: Phosphor Bronze
Plating:
Underplating: 50 μ” [1.27 μm] Nickel
Wiping Area: See Ordering Information
Solder Tails: See Ordering Information
Electrical
Current Rating: Signal: 1.5 A - All contacts simultaneously
Insulation Resistance: 103 MΩ
Withstanding Voltage: 1,000 VAC
Environmental
Temperature Rating: -55°C to +125°C
Process Temperature Rating: 260°C (Profile per J-STD-020C)
Moisture Sensitivity Level: 1 (per J-STD-020C)
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin
MP2 Series
POSITION X
2.00
.079
"A" 6.00
.236
POSITION 2
POSITION 1
15.80
.622
11.50
.453
1.40
.055
2.00
.079
17.00
.669
FOR SPECIAL MONOBLOCKS
AND PIN ARRANGEMENTS
CONTACT 3M SALES
REPRESENTATIVE
mm
[inch]
3.50
.138
Tolerance Unless Noted
12.00
.472
mm
4 ROW PRODUCT
0
0.0
0.00
±3
±0.3
±0.13
[ ] Dimensions for Reference Only
17.80
.701
13.52
.532
MATING LENGTH
"B" TAIL LENGTH
14.00
.551
E D C B A
"C"
ROW
5 ROW PRODUCT
SOLDER TAIL
PRODUCT
PRESS-FIT
PRODUCT
PRESS-FIT
PRODUCT
REAR
PLUG-UP
Note:
1. Refer to IEC 61076-4-104 Futurebus+® global standard.
2. “Press Fit” describes a contact tail having a compliant section designed to make a reliable electrical connection with a
plated through-hole (PTH) in a printed circuit board, typically a “back plane.”
Ordering Information
MP2 - HXXX - XXXX - S - XXXXX
Plating Options:
(See Table 4)
H = Header
Pin Count
(See Table 1)
Shouldered Pins
Rows
4 = 4 Rows
5 = 5 Rows
Loading Pattern
(See Table 2)
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
Tail Length
(See Table 3)
Termination Style
P = Press-Fit
S = Solder Tail
TS-1120-C
Sheet 2 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin
Table 1 - Connector & Row Lengths
Table 4 - Plating Options
Pin
Count
Dim. “A”
mm [inch]
Dim “C”
mm [inch]
Rows
024
11.95 [0.471]
10.00 [0.394]
4
048
23.95 [0.943]
22.00 [0.866]
4
072
35.95 [1.415]
34.00 [1.339]
4
096
47.95 [1.889]
46.00 [1.811]
4
120
59.95 [2.36]
58.00 [2.283]
4
144
71.95 [2.833]
70.00 [2.756]
4
168
83.95 [3.305]
82.00 [3.228]
4
192
95.95 [3.778]
94.00 [3.701]
4
030
11.95 [0.471]
10.00 [0.394]
5
060
23.95 [0.943]
22.00 [0.866]
5
090
35.95 [1.415]
34.00 [1.339]
5
120
47.95 [1.888]
46.00 [1.811]
5
150
59.95 [2.361]
58.00 [2.283]
5
180
71.95 [2.833]
70.00 [2.756]
5
210
83.95 [3.305]
82.00 [3.228]
5
240
95.95 [3.778]
94.00 [3.701]
5
Plating
Suffix
Press-Fit
Tails*
Solder
Tails
TG
(RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.25 μm [10 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TG30
(RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.76 μm [30 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TR30
(RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TR40B
(RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.13 μm [5 μ”] Min. Hard Au Contact Area,
Lubricated
1.02 μm [40 μ”] Min. PdNi Contact Area
0.10 μm [4 μ”] Min. Pd Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
FJ
(RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.25 μm [10 μ”] Min. Au Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
KR
(RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.76 μm [30 μ”] Min. Au Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
RF
(RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
1.27 μm [50 μ”] Min. Au Contact Area, Lubricated
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
LR
(RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
Table 3 - Tail Length Options
Termination Option No.
Solder Tail
Press-Fit* Tail
1
2
3
1
5 (Contact 3M)
7 (Contact 3M)
*Compliant-Pin Tail
MP2 Series
Dim. “B”
4.60 [0.181]
3.53 [0.139]
2.72 [0.107]
13.60 [0.535]
17.00 [0.669]
Plating Composition
PD
(RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.13 μm [5 μ”] Min. Hard Au Contact Area,
Lubricated
1.02 μm [40 μ”] Min. PdNi Contact Area
0.10 μm [4 μ”] Min. Pd Contact Area
5.08 μm [200 μ”] Min. Matt Whisker Mitigating
Sn Tail Area
KV
(RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.76 μm [30 μ”] Min. Au Dual Contact Areas
0.10 μm [4 μ”] Min. Au Needle Eye
1.27 μm [50 μ”] Min. Ni all over
Table 2 - Mate Length vs. Loading Pattern
Loading Pattern
Code
Description
Mate length
Row A
Mate length
Row B
Mate length
Row C
Mate length
Row D
Mate length
Row E
(5-Row Prod. Only)
1
All Positions Filled
5.00 [0.197]
5.00 [0.197]
5.00 [0.197]
5.00 [0.197]
5.00 [0.197]
2
All Positions Filled
6.50 [0.256]
5.00 [0.197]
5.00 [0.197]
5.00 [0.197]
5.00 [0.197]
3
All Positions Filled
6.50 [0.256]
5.75 [0.226]
5.75 [0.226]
6.50 [0.256]
6.50 [0.256]
4
All Positions Filled
6.50 [0.256]
6.50 [0.256]
6.50 [0.256]
6.50 [0.256]
6.50 [0.256]
5
All Positions Filled
5.75 [0.226]
7.25 [0.285]
5.75 [0.226]
5.75 [0.226]
5.75 [0.226]
6
All Positions Filled
7.25 [0.285]
5.75 [0.226]
5.75 [0.226]
5.75 [0.226]
5.75 [0.226]
7
All Positions Filled
6.50 [0.256]
5.75 [0.226]
5.00 [0.197]
5.00 [0.197]
5.00 [0.197]
8
All Positions Filled
6.50 [0.256]
5.00 [0.197]
6.50 [0.256]
6.50 [0.256]
6.50 [0.256]
9
All Positions Filled
5.00 [0.197]
6.50 [0.256]
5.00 [0.197]
5.00 [0.197]
5.00 [0.197]
A
All Positions Filled
5.00 [0.197]
5.75 [0.226]
6.50 [0.256]
5.75 [0.226]
5.00 [0.197]
B
All Positions Filled
5.75 [0.226]
5.75 [0.226]
5.75 [0.226]
5.75 [0.226]
5.75 [0.226]
C
All Positions Filled
5.00 [0.197]
5.00 [0.197]
6.50 [0.256]
5.00 [0.197]
5.00 [0.197]
D
All Positions Filled
5.75 [0.226]
5.75 [0.226]
7.25 [0.285]
5.75 [0.226]
5.75 [0.226]
E
All Positions Filled
7.25 [0.285]
7.25 [0.285]
7.25 [0.285]
7.25 [0.285]
7.25 [0.285]
G
All Positions Filled
7.25 [0.285]
5.75 [0.226]
5.75 [0.226]
5.00 [0.197]
5.00 [0.197]
H
All Positions Filled
5.00 [0.197]
5.75 [0.226]
5.75 [0.226]
7.25 [0.285]
7.25 [0.285]
J
All Positions Filled
8.00 [0.315]
8.00 [0.315]
8.00 [0.315]
8.00 [0.315]
8.00 [0.315]
K
All Positions Filled
5.00 [0.197]
6.50 [0.256]
7.25 [0.285]
6.50 [0.256]
5.00 [0.197]
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
TS-1120-C
Sheet 3 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5-Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin
12.00
.472
16.00 MIN
.630
MP2 Series
1 6 .0 0 M IN
.6 3 0
2.00
.079
2.00
.079
A1
12.00
.472
"C"
"D" PLATED THRU HO LE
Ø 0.10
12.00
.472
2.00
.079
1.50 +.10
-.00
Ø
CENTER HOLES OPTIONAL
FOR 3M PRODUCT
6.00
.236
UNPLATED
.059 +.004
-.000
"D " P L A T E D T H R U H O L E
Ø 0 .1 0
Ø 0.10
RECOMMENDED 4 ROW SOLDER
TAIL PCB HOLE MOUNTING PATTERN
RECOMMENDED 4 ROW PRESS-FIT
Table 5 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY
HOLE
Finished Dia. mm [in]
Cu Thickness mm [in]
SnPb Thickness microns [μ”]
Drilled Hole Dia. mm [in]
“D”
0.65-0.80 [.0256-.0315]
0.025 [.001] min.
15 [600] max.
0.81-0.86 [.0319-.0339]
Table 6 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY
Hole
Finished Dia.
mm [in]
Cu Thickness
mm [in]
Immersion
Matte Sn
Thickness
microns [μ”]
Electrolitic Au
Thickness
microns [μ”]
OSP ENTEK
Thickness
microns [μ”]
Drilled Hole Dia.
mm [in]
“D”
0.700-0.800
[.0276-.0315]
0.025-0.045
[0.001-0.002]
0.5 - 2.5
[20 - 100]
0.1 - 0.5
[4 - 20]
0.2 - 0.5
[8 - 20]
0.830-0.860 [.0330-.0340] or
0.85mm [ #66] TWIST DRILL
18.00 MIN
.709
14.00
.551
6.00
.236
2.00
.079
"D " P L A T E D T H R U H O L E
Ø 0 .1 0
2.00
.079
A1
12.00
.472
"C"
12.00
.472
"D" PLATED THRU HOLE
Ø 0.10
2.00
.079
Ø
1.50
.059
+.10
-.00
+.004
-.000
UNPLATED
CENTER HOLES OPTIONAL
FOR 3M PRODUCT
Ø 0.10
RECOMMENDED 5 ROW SOLDER
TAIL PCB HOLE MOUNTING PATTERN
1 8 .0 0 M IN
.7 0 9
RECOMMENDED 5 ROW PRESS-FIT
PCB HOLE MOUNTING PATTERN
TS-1120-C
Sheet 4 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217B-E
3M is a trademark of 3M Company.