MP2-S150G-51M1-C-TR40B

3M™ MetPak™ 2-FB Socket 2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series • End-to-end stackable • Offset dual-beam contact minimizes insertion force • Molded guide fingers provide integrated alignment • Alignment wafer for true position • Mates with MP2-P inverse headers and elevated inverse headers, MP2-PXXXE, for extended card applications • Protective Push-Cap on Press-Fit Only • Meets IEC 61076-4-104 Futurebus+® global standard • See Regulatory Information Appendix (RIA) for chemical compliance information Date Modified: April 6, 2007 TS-1117-06 Sheet 1 of 4 Physical Insulation Material: High Temp LCP Flammability: UL 94V-0 Color: Beige Contact Material: Copper Alloy Plating Underplating: 50 μ″ (1.27 μm) Nickel Wiping Area: See Ordering Information Solder Tails: See Ordering Information Electrical Current Rating: Signal: 1.5 A - All contacts simultaneously Insulation Resistance: 103 MΩ Withstanding Voltage: 1000 VAC Environmental Temperature Rating: -55°C to +125°C Process Temperature Rating: 260°C (Profile per J-STD-020C) Moisture Sensitivity Level: 1 (per J-STD-020C) UL File No: E68080 3M Interconnect Solutions http://www.3M.com/interconnects/ MetPak is a trademark of 3M Company. * Futurebus+ is a registered trademark of the Institute of Electrical and Electronic Engineers, Inc. (IEEE). 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ 2-FB Socket 2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series "A" 5.00 .197 32.97 1.298 22.42 .883 TYP. ROW E D C B A 14.50 .571 POSITION 1 2 11.30 .445 13.30 .524 POSITION X 2.00 .079 4X 3.75 .148 "C" TAIL LENGTH 13.50 .532 23.00 .906 PRESS-FIT AND SOLDER TAIL PRODUCT (CAPPED) 21.95 .864 2.00 .079 TYP. "B" 0.05 ±.05 .002 ±.002 23.30 .917 MATED WITH MP2-PXXXE-5XXX-XXXX 23.30 1.50 .917 .059 CENTER LINE OF ROW A mm ASSEMBLED TO PCB AND MATED WITH MP2-PXXX-5XXX-XXXX [inch] Tolerance Unless Noted Note: 1. Refer to IEC 61076-4-104 Futurebus+® global standard. 2. "Press Fit" describes a contact tail having a compliant section designed to make a reliable electrical connection with a plated through-hole (PTH) in a printed circuit board, typically a "back plane.” mm 0 0.0 0.00 ±3 ±0.3 ±0.13 [ ] Dimensions for Reference Only Ordering Information MP2 - SXXXG - 5XXX-C - XXXXX S = Socket Contact Count See Table C = Capped Solder Tail Blank = Press-Fit Tail Length See Table 2 Guide Finger Contact Arrangement Rows 1 = All positions filled* 5 = 5 Rows Termination Style M = Solder Tail (Press Peg) P = Press-Fit (w/Tail Cover) *Contact 3M Sales Representative for information on special fill patterns and mono blocked pairs. 3M Interconnect Solutions http://www.3M.com/interconnects/ Plating Options: (See Table 3) TS-1117-06 Sheet 2 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ 2-FB Socket 2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series Table 1 - Connector & Row Lengths Pin Count Dim. "A" mm [inch] Block Rows Count Dim "B" mm [inch] Table 2 - Tail Length 030 11.95 [0.471] 10.00 [0.394] 5 1 060 23.95 [0.943] 22.00 [0.866] 5 2 090 35.95 [1.415] 34.00 [1.339] 5 3 120 47.95 [1.888] 46.00 [1.811] 5 4 Solder 150 59.95 [2.361] 58.00 [2.283] 5 5 1 180 71.95 [2.833] 70.00 [2.756] 5 6 2 210 83.95 [3.305] 82.00 [3.228] 5 7 240 95.95 [3.778] 94.00 [3.701] 5 8 Contact-to-PC Board Tail Termination Option No. Dim. "C" Press-Fit* 1 2.72 [0.107] 3.53 [0.139] *Compliant-Pin Tail Table 3 - Plating & Regulatory Plating Suffix Press-Fit Tails* Solder Tails TG RIA E2 & C2 apply RIA E3 & C2 apply Plating Composition 0.25 µm [10 µ"] Min. Au Contact Area 2.54 µm [100 µ"] Min. SnPb Tail Area 1.27 µm [50 µ"] Min. Ni all over TG30 RIA E2 & C2 apply RIA E3 & C2 apply 0.76 µm [30 µ"] Min. Au Contact Area 2.54 µm [100 µ"] Min. SnPb Tail Area 1.27 µm [50 µ"] Min. Ni all over 0.08 µm [3 µ"] Min. Au Contact Area TR30 RIA E2 & C2 apply RIA E3 & C2 apply 0.67 µm [27 µ"] Min. PdNi Contact Area 2.54 µm [100 µ"] Min. SnPb Tail Area 1.27 µm [50 µ"] Min. Ni all over 0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated TR40B RIA E2 & C2 apply RIA E3 & C2 apply 1.02 µm [40 µ"] Min. PdNi Contact Area 0.10 µm [4 µ"] Min. Pd Contact Area 2.54 µm [100 µ"] Min. SnPb Tail Area 1.27 µm [50 µ"] Min. Ni all over FJ RIA E1 & C1 apply RIA E1 & C1 apply 0.25 µm [10 µ"] Min. Au Contact Area 5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area 1.27 µm [50 µ"] Min. Ni all over KR RIA E1 & C1 apply RIA E1 & C1 apply 0.76 µm [30 µ"] Min. Au Contact Area 5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area 1.27 µm [50 µ"] Min. Ni all over RF RIA E1 & C1 apply RIA E1 & C1 apply 1.27 µm [50 µ"] Min. Au Contact Area, Lubricated 5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area 1.27 µm [50 µ"] Min. Ni all over 0.08 µm [3 µ"] Min. Au Contact Area LR RIA E1 & C1 apply RIA E1 & C1 apply 0.67 µm [27 µ"] Min. PdNi Contact Area 5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area 1.27 µm [50 µ"] Min. Ni all over 0.13 µm [5 µ"] Min. Hard Au Contact Area, Lubricated PD RIA E1 & C1 apply RIA E1 & C1 apply 1.02 µm [40 µ"] Min. PdNi Contact Area 0.10 µm [4 µ"] Min. Pd Contact Area 5.08 µm [200 µ"] Min. Matt Whisker Mitigating Sn Tail Area 1.27 µm [50 µ"] Min. Ni all over *Compliant-Pin Tail TS-1117-06 Sheet 3 of 4 3M Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ 2-FB Socket 2 mm 5-Row, Right Angle, Solder or Press-Fit Tail, Guide Fingers MP2 Series 8.00 .315 4.00 .157 2.00 .079 4X 1.00 .039 THESE HOLES CONSTITUTE MODULAR REPEATING PATTERN 2.00 .079 TYP. 4.00 .157 "B" 2.05 +.05 -.00 l O 0.10 .081 +.002 -.000 UNPLATED THRU HOLE UNPLATED THROUGH-HOLE O A1 1.50 +.10 -.00 l O 0.10 .059 +.004 -.000 UNPLATED THRU HOLE UNPLATED THROUGH-HOLE “D” PLATED "D"THROUGH-HOLE PLATED THRU HOLE O l O 0.10 3.00 .118 RECOMMENDED PCB HOLE MOUNTING PATTERN Table 4 -- HOLE PLATING For TG, TG30, TR30, TR40B FINISHES ONLY HOLE Finished Dia. mm [in] Cu Thickness mm [in] SnPb Thickness microns [µ"] Drilled Hole Dia. mm [in] "D" 0.65-0.80 [.0256-.0315] 0.025 [.001] min 15 [600] max 0.81-0.86 [.0319-.0339] Table 5 -- HOLE PLATING For FJ, KR, RF, LR, and PD FINISHES ONLY Hole "D" Finished Dia. mm [in] Cu Thickness mm [in] Immersion Matte Sn Thickness microns [µ"] Electrolitic Au Thickness microns [µ"] OSP ENTEK Thickness microns [µ"] 0.700-0.800 0.025-0.045 0.5 - 2.5 0.1 - 0.5 0.2 - 0.5 0.830-0.860 [.0330-.0340] or [.0276-.0315] [0.001-0.002] [20 - 100] [4 - 20] [8 - 20] 0.85mm [ #66] TWIST DRILL Drilled Hole Dia. mm [in] TS-1117-06 Sheet 4 of 4 3M Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/17/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. RIA-2217-A CHINA Appendix C1: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS 20 Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. Name and Content of Hazardous Substances or Elements Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 800/225-5373 www.3M.com/interconnects RIA-2217-A © 3M 2007