MP2-SP08-41M2-TG30

3M™ MetPak™ 2-FB Power Socket 2 mm 4/5-Row, Right Angle, Solder or Press-Fit Tail • • • • • MP2 Series 6.50 Amps per contact End-to-end stackable Press or heat stake peg (solder tail) Futurebus+® compatible See the Regulatory Information Appendix (RIA) in the “RoHS compliance” section of www.3Mconnectors.com for compliance information (RIA E1 & C1 apply)  TS-1125-E Sheet 1 of 4 Physical Insulation: Material: High Temperature LCP Flammability: UL 94V-0 Color: Beige Contact: Material: Copper Alloy Plating: Underplating: 50 μ” [1.27 μm] Nickel Wiping Area: See Ordering Information Tails: See Ordering Information Electrical Current Rating: Power: 6.50 A per power socket contact at 70°C Insulation Resistance: 103 MΩ Withstanding Voltage: 1,500 VAC for 60 seconds Environmental Temperature Rating: -55° C to 125° C Process Temperature Rating: 260°C (Profile per J-STD-020C) Moisture Sensitivity Level: 1 (per J-STD-020C) UL File No.: E68080 3 Electronics Materials Solutions Division Interconnect Solutions http://www.3Mconnectors.com Futurebus+ is a registered trademark of the Institute of Electrical and Electronic Engineers, Inc. (IEEE) 3M and MetPak are trademarks of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ 2-FB Power Socket 2 mm 4/5-Row, Right Angle, Solder or Press-Fit Tail 11.95 .470 MP2 Series 12.45 .490 11.80 .465 21.0 .83 9.30 .366 3.00 .118 "A" TAIL LENGTH 13.50 .531 POSITION 2 POSITION 1 2.00 .079 TYP. 6.00 .236 "B" 2.00 .079 5X 10.00 .394 9.50 .374 4 ROW PRODUCT FOR SPECIAL MONOBLOCKS CONTACT 3M SALES REPRESENTATIVE mm (Inch) Tolerance Unless Noted mm 0 ±3 0.0 ±0.3 0.00 ±0.13 ( ) Dimensions used for Reference Only 12.45 .490 ROW E D C B A 13.80 .543 23.0 .91 11.30 .445 5 ROW PRODUCT 8.00 .315 Note: 1. Refer to IEC 61076-4-104 Futurebus+® global standard. 2. “Press Fit” describes a contact tail having a compliant section designed to make a reliable electrical connection with a plated through-hole (PTH) in a printed circuit board, typically a “back plane.” Ordering Information MP2-SPXX-X1XX- XXXXX SP = Power Socket Plating Options: (See Table 3) Contact Count (See Table 1) Rows 4 = 4 Rows 5 = 5 Rows Tail Length (See Table 2) Termination Style P = Press-Fit M = Solder Tail (Press Peg) 3 Electronic Materials Solutions Division Interconnect Solutions http://www.3Mconnectors.com TS-1125-E Sheet 2 of 4 3M and MetPak are trademarks of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ 2-FB Power Socket 2 mm 4/5-Row, Right Angle, Solder or Press-Fit Tail MP2 Series Table 1 Pin Count No of Rows 08 4 10 5 Table 2 - Tail & Post Lengths Contact-to-PC Board Tail Termination Option No. Dim. “A” Dim. “B” S1 2.72 [0.107] 5.20 [0.205] S2 3.53 [0.139] 6.00 [0.256] M1 2.72 [0.107] 3.75 [0.148] 3.53 [0.139] 3.75 [0.148] Solder M2 Press-Fit* P1 *Compliant-Pin Tail Table 3 - Plating Plating Suffix Press-Fit Tails* Solder Tails Plating Composition KR RIA E1 & C1 apply RIA E1 & C1 apply 0.76 μm [30 μ”] Min. Au Contact Area 2.54 μm [100 μ”] Min. Matt Whisker Mitigating Sn Tail Area 1.27 μm [50 μ”] Min. Ni all over LR RIA E1 & C1 apply RIA E1 & C1 apply 0.08 μm [3 μ”] Min. Au Contact Area 0.67 μm [27 μ”] Min. PdNi Contact Area 2.54 μm [100 μ”] Min. Matt Whisker Mitigating Sn Tail Area 1.27 μm [50 μ”] Min. Ni all over *Compliant-Pin Tail TS-1125-E Sheet 3 of 4 3 Electronic Materials Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M and MetPak are trademarks of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ MetPak™ 2-FB Power Socket 2 mm 4/5-Row, Right Angle, Solder or Press-Fit Tail 2.00 .079 MP2 Series 6.00 .236 3X 4.00 .157 2.00 .079 TYP. 1.00 .039 A1 4.00 .157 "B" 2.05 +.05 -.00 Ø 0.10 .081 +.002 -.000 UNPLATED THRU HOLE UNPLATED THROUGH-HOLE Ø Ø “D” PLATED THROUGH-HOLE 3.00 .118 Ø 0.10 1.50 .059 +.10 -.00 +.004 -.000 Ø 0.10 UNPLATED THROUGH-HOLE Recommended 4 Row PCB Hole Mounting Pattern 2.00 .079 4X 8.00 .315 Recommended 5 Row PCB Hole Mounting Pattern Table 4 - HOLE PLATING FINISHES HOLE Finished Dia. mm [in] Cu Thickness mm [in] Immersion Matte Sn Thickness microns [μ”] Electrolitic Au Thickness microns [μ”] OSP ENTEK Thickness microns [μ”] Drilled Hole Dia. mm [in] “D” 0.700-0.800 [.0276-.0315] 0.025-0.045 [0.001-0.002] 0.5 - 2.5 [20 - 100] 0.1 - 0.5 [4 - 20] 0.2 - 0.5 [8 - 20] 0.830-0.860 [.0330-.0340] or 0.85mm [ #66] TWIST DRILL TS-1125-E Sheet 4 of 4 3 Electronic Materials Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M and MetPak are trademarks of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory: For regulatory information about this product, contact your 3M representative. Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Product Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method of application. Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M Product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. 3 3M Electronics Materials Solutions Division 6801 River Place Blvd. 3M and MetPak are Austin, TX 78726-9000 trademarks of 3M Company. All other trademarks belong to their U.S.A. respective owners. Please 1-800-225-5373 recycle. Printed in USA. © 3M 2017. All rights reserved. www.3Mconnectors.com RIA-2217B-E