SL8802/08-20DN5-00

4 3 2 1 NOTES 1 DIMENSIONS ARE IN MILLIMETERS. 3MTM TWIN AXIAL CABLE, SL8800 SERIES 2 PHYSICAL: COLOR: SILVER MARKING: 3M (part number) 30 AWG (signal plating) (lot code) EXAMPLE: 3M SL8802/08-20DN5-00 30 AWG SILVER TW602-1 D 3 ELECTRICAL: IMPEDANCE: 100 C UL FILE NUMBER: E42769 3 6 THE OUTER SURFACE OF THE RIBBON CABLE HAS A METALLIC APPEARANCE, BUT IS NOT CONDUCTIVE. THERE IS A TRANSLUCENT POLYESTER OUTER LAYER OVER AN ALUMINUM SHIELDING LAYER, WHICH GIVES THIS APPEARANCE. 2 PLACES C 0.874 0.038 0.79 4 PLACES C THIS CABLE CONSTRUCTION HAS A THIN ALUMINUM LAYER AT EACH EDGE. USER SHOULD EVALUATE ITS USE IN THEIR APPLICATION AND, IF NECESSARY, INSULATING TAPE MAY BE APPLIED TO COVER THE ALUMINUM LAYER, AS USER DEEMS APPROPRIATE. SIGNAL WIRES: 30 AWG SOLID ( 0.254 [.0100]) SILVER OR TIN PLATED COPPER 0.787 [.0310] POLYOLEFIN INSULATION 8 PLACES GROUND WIRES: 30 AWG SOLID ( 0.254 [.0100]) TIN PLATED COPPER 2 PLACES 7 FOIL AND INSULATOR STRIPPING BLADE DESIGN DRAWINGS ARE AVAILABLE UPON REQUEST. TOOLING REFERENCE NUMBER: NU7E 8 C DENOTES CRITICAL DIMENSION. B C Imaged: Central Standard Time 8/7/2018 -- UTC Offset (hrs) 6 6.52 +0.25 1.00 -0.00 D C REVISION C DRAWING NUMBER 8.23 5 REGULATORY INFORMATION: ROHS COMPLIANT. SEE THE REGULATORY INFORMATION APPENDIX (RIA) IN THE "ROHS COMPLIANCE" SECTION OF WWW.3MCONNECTORS.COM FOR COMPLIANCE INFORMATION (RIA E1 & C1 APPLY) 78-5100-2413-2 5.37 2.86 5 OHMS 4 PRODUCT SPECIFICATION NUMBER: PS-0105 15.60 3.66 D B SIGNAL WIRE PLATING OPTION 3M PART NUMBER SILVER SL8802/08-20DN5-00 ADDED CRITICAL DIM SYMBOLS TIN SL8802/08-21DN5-00 ADDED NOTE 8 D 79896 AUG 07,2018 REVISED TOLERANCE 3 DESIGN REFERENCE NEXT ASSEMBLY ACCESS CODES DIVISION REV ECO ISSUE DATE AND DESCRIPTION DRFT DATE MWL APR 11,2011 CHKD DATE DIVISION CODE C 3M Center DO NOT SCALE DRAWING A SCALE 15 1 THIRD ANGLE PROJECTION INTERPRET PER ASME Y14.5 - 2009 MAX SURFACE ROUGHNESS Visit http://www.3mconnectors.com 125 ALL SURFACES MARKED ONLY 4 3 2 St. Paul, TOLERANCES EXCEPT AS NOTED INCHES .0 .00 .000 .0000 MILLIMETERS 0 .0 .00 .10 .000 ANGLES 1 LDS MML MN 55144 DRFT MFG DATE APPVL DATE CHKD 3M COPYRIGHT 2018 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE SL8802/08-2XDN5-00, 100 OHM, 30 AWG, 4PR CAGE SIZE NUMBER MODEL DRAWING NO. REV. 78-5100-2413-2 DET. LISTS 1 YES NO D SHT 1 OF 2 A 4 3 2 1 D D Regulatory: For regulatory information about this product, visit 3M.com/regs or contact your 3M representative. Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. D C 78-5100-2413-2 DRAWING NUMBER Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OR TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M's option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. B B 3M Electronics Materials Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 1-800-225-5373 www.3M.com/interconnect D 79896 AUG 07,2018 LDS MML ADDED CRITICAL DIM SYMBOLS ADDED NOTE 8 REVISED TOLERANCE 3 DESIGN REFERENCE NEXT ASSEMBLY ACCESS CODES DIVISION REV ECO ISSUE DATE AND DESCRIPTION DRFT DATE MWL APR 11,2011 CHKD DATE DIVISION CODE C 3M Center DO NOT SCALE DRAWING A SCALE 1 1 THIRD ANGLE PROJECTION INTERPRET PER ASME Y14.5 - 2009 MAX SURFACE ROUGHNESS 125 ALL SURFACES MARKED ONLY 4 3 Imaged: Central Standard Time 8/7/2018 -- UTC Offset (hrs) 6 C REVISION Product Use: Many factors beyond 3M's control and uniquely within user's control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user's method of application. 2 St. Paul, TOLERANCES EXCEPT AS NOTED INCHES .0 .00 .000 .0000 MILLIMETERS 0 .0 .00 .10 .000 ANGLES 1 MN 55144 DRFT MFG DATE APPVL DATE CHKD 3M COPYRIGHT 2018 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE SL8802/08-2XDN5-00, 100 OHM, 30 AWG, 4PR CAGE SIZE NUMBER MODEL DRAWING NO. REV. 78-5100-2413-2 DET. LISTS 1 YES NO D SHT 2 OF 2 A