UHM-S110A3-5AP1-TG30

8 7 6 5 4 3 2 1 NOTES 1. MATERIAL: PLASTIC: HIGH TEMP LCP, UL94V-0 CONTACTS: COPPER ALLOY. 3MTM ULTRA HARD METRIC (UHM) PRESS-FIT SOCKET CONNECTORS, 5-ROW FOR 2MM HARD METRIC APPLICATIONS 2. REGULATORY INFORMATION: ROHS COMPLIANT. SEE THE REGULATORY INFORMATION APPENDIX (RIA) IN THE "ROHS COMPLIANCE" SECTION OF WWW.3MCONNECTORS.COM FOR COMPLIANCE INFORMATION. D D 3 IN THE EVENT OF CONFLICT BETWEEN THIS DATA AND THAT CONTAINED IN THE PRODUCT SPECIFICATION, THE PRODUCT SPECIFICATION TAKES PRECEDENT. C UHM-S110AX-5AP1-XXXXX UHM-S055CLX-5AP1-XXXXX 3 C MECHANICAL: 3 B ORDERING INFORMATION 3 UHM-SXXXYZ-5AP1-XXXXX B DRAWING NUMBER B ENVIRONMENTAL: TEMPERATURE RATING: -55 C TO 125 C PLATING: SOCKET POSITION AND TYPE HIGH SPEED OPTION 0 = 50O COAXIAL SINGLE-ENDED AND 100O DIFFERENTIAL PAIR APPLICATIONS FOR CONNECTION TO 5 +2 ROW HEADERS OUTER ROW GROUND TAILS IN ODD POSITIONS OF ROW F/Z 3 = 50O COAXIAL SINGLE-ENDED AND 100O DIFFERENTIAL PAIR APPLICATIONS FOR CONNECTION TO 5 +2 ROW HEADERS OUTER ROW GROUND TAILS IN ALL POSITIONS OF ROW F/Z TG30 = .76 M [30 IN] MIN. GOLD ON CONTACT AREA 2.54 M [100 IN] MIN. TIN/LEAD ON TERMINAL AREA (RIA C2 & E2 APPLY) 1.27 M [50 IN] MIN. NICKEL ALL OVER. STANDARD OPTION. B KR = .76 M [30 IN] MIN. GOLD ON CONTACT AREA 2.54 M [100 IN] MIN. MATTE TIN ON TERMINAL AREA (RIA C1 & E1 APPLY) 1.27 M [50 IN] MIN. NICKEL ALL OVER. A DESIGN REFERENCE NEXT ASSEMBLY ACCESS CODES DO NOT SCALE DRAWING 3M ELECTRONIC SOLUTIONS DIVISION INTERCONNECT SOLUTIONS http://www.3mconnectors.com 3 1 MAY 24,2012 MAX SURFACE ROUGHNESS ALL SURFACES MARKED ONLY 3 ECO ISSUE DATE AND DESCRIPTION DRFT DATE CASTIGLIONE MAY 23,2012 CHKD DATE ISD 3M Center INCHES INTERPRET PER ASME Y14.5 - 2009 3M IS A TRADEMARK OF 3M COMPANY. FOR TECHNICAL, SALES OR ORDERING INFORMATION CALL 800-225-5373 REV St. Paul, TOLERANCES EXCEPT AS NOTED SCALE THIRD ANGLE PROJECTION 4 41080 DIVISION CODE Interconnect Solutions 5 DEC 04,2014 JNC TS JNC TS DRFT CHKD PRODUCTION RELEASE DIVISION 6 58359 REMOVE MRKT FEATURES & WITHSTANDING VOLTAGE WAS 750 A 7 78-5100-2533-7 ELECTRICAL: DATA RATE: 7+ Gbps DATA RATES (WHEN MATED TO STANDARD IEC 61076-4-101 HEADERS) CHARACTERISTIC IMPEDANCE: 50O SINGLE-ENDED, 100O DIFFERENTIAL CURRENT RATING (FULLY LOADED): 1A @ 70 C SIGNAL INSULATION RESISTANCE: 104 MO @ 100 VDC WITHSTANDING VOLTAGE: 625VRMS UHM-S055CRX-5AP1-XXXXX 8 REVISION NORMAL FORCE (NOMINAL): .57N [58g] SIGNAL, (.74N [75g] SHIELD WITH HSHM AND UHM HEADERS) ENGAGEMENT FORCE (NOMINAL): .32N [33g] SIGNAL, (.22N [22g] SHIELD WITH HSHM AND UHM HEADERS) SEPARATION FORCE (NOMINAL): .20N [20g] SIGNAL, (.20N [20g] SHIELD WITH HSHM AND UHM HEADERS) WIPE (NOMINAL, SHORTEST CONTACT): 2.67 [.105] SIGNAL, 1.57 [.062] SHIELD MATE/UNMATE CYCLES: 250 APPLICATION: THIS MODULE IS NOT SUITABLE FOR STAND-ALONE USE. ADDITIONAL GUIDE FEATURES RECOMMENDED PER IEC 61076-4-101 2 .0 .00 .000 .0000 .01 .005 MILLIMETERS 0 .0 .3 .00 .13 .000 ANGLES MN 55144 MFG DATE APPVL DATE T. SUNIGA MAY 23,2012 C 3M COPYRIGHT 2012 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE UHM PRESS-FIT SOCKET, 5-ROW, CONNECTORS CAGE SIZE DRAWING NO. NUMBER REV. 78-5100-2533-7 MODEL DET. LISTS 1 YES NO B SHT 1 OF 3 Imaged: B.1 12/4/2014 2:00 PM UTC-06:00 UHM-S055BX-5AP1-XXXXX UHM-S095BX-5AP1-XXXXX UHM-S110BX-5AP1-XXXXX UHM-S125BX-5AP1-XXXXX A 8 7 6 5 4 3 2 1 3MTM ULTRA HARD METRIC (UHM) PRESS-FIT SOCKET CONNECTORS, 5-ROW FOR 2MM HARD METRIC APPLICATIONS D D OUTER GROUND SHIELD CONTACTS OUTER GROUND SHIELD CONTACTS DIM. "A" 50.00 1.969 DIM. "B" 48.00 1.890 2.00 .079 2.00 .079 TYP. F TYP. C 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 E E D D C C B B A A Z Z 1 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 2.00 .079 2.00 .079 2.00 .079 TYP. TYP. 8 7 6 5 4 3 2 1 TYP. .079 2.00 TYP. .079 SIGNAL CONTACT QTY. DIM. "A" DIM. "B" 055 22.00 [.866] 20.00 [.787] 095 38.00 [1.496] 36.00 [1.417] 110 44.00 [1.732] 42.00 [1.654] 125 50.00 [1.969] 48.00 [1.890] C 2.00 TYP. B REVISION UHM-S110AX-5AP1-XXXXX UHM-S055BX-5AP1-XXXXX UHM-S095BX-5AP1-XXXXX UHM-S110BX-5AP1-XXXXX UHM-S125BX-5AP1-XXXXX 20.40 .803 DRAWING NUMBER 2.00 .079 F 78-5100-2533-7 TYP. 2.80 12.35 11.75 .486 .463 11.12 .110 .438 B B 3.30 3.88 .130 .153 8.80 .346 TAILS 10.70 .421 OUTER GROUND TAIL TYPICAL SIDE VIEW DIMENSIONS FOR THE SOCKETS ON THIS DRAWING B 20.00 .787 58359 DEC 04,2014 A F F E E D D 2.00 .079 7 6 5 4 3 2 DESIGN REFERENCE NEXT ASSEMBLY ACCESS CODES A 1 11 10 9 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1 TYP. 3 1 THIRD ANGLE PROJECTION INTERPRET PER ASME Y14.5 - 2009 UHM-S055CRX-5AP1-XXXXX MAX SURFACE ROUGHNESS MARKED ONLY 6 ISSUE DATE AND DESCRIPTION DATE CASTIGLIONE MAY 23,2012 CHKD DATE 5 4 3 ISD 3M Center INCHES ALL SURFACES 7 ECO DRFT St. Paul, TOLERANCES EXCEPT AS NOTED SCALE 2.00 .079 9X 2.00 .079 8 REV DIVISION CODE Interconnect Solutions Z UHM-S055CLX-5AP1-XXXXX MAY 24,2012 JNC TS DRFT CHKD PRODUCTION RELEASE DIVISION Z 8 41080 B A 11 10 9 A C TYP. B TS REMOVE MRKT FEATURES & WITHSTANDING VOLTAGE WAS 750 10X 2.00 .079 C JNC 2 .0 .00 .000 .0000 .01 .005 MILLIMETERS 0 .0 .3 .00 .13 .000 ANGLES MN 55144 MFG DATE APPVL DATE T. SUNIGA MAY 23,2012 C 3M COPYRIGHT 2012 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE UHM PRESS-FIT SOCKET, 5-ROW, CONNECTORS CAGE SIZE DRAWING NO. NUMBER REV. 78-5100-2533-7 MODEL DET. LISTS 1 YES NO B SHT 2 OF 3 Imaged: B.1 12/4/2014 2:00 PM UTC-06:00 25.00 .984 A 8 7 6 5 4 3 2 1 3MTM ULTRA HARD METRIC (UHM) PRESS-FIT SOCKET CONNECTORS, 5-ROW FOR 2MM HARD METRIC APPLICATIONS B D D B 48.00 1.890 DIM. "B" A A DIM. "D" .10 A B C PLATED THRU HOLES 132X DIM. "D" 20X 2.00 .079 .10 A B C PLATED THRU HOLES 2.00 .079 TYP. F/Z F/Z E E 10.00 D 10.00 D .394 C .394 C B B A A C 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 C 5X 2.00 .079 1 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 5X 2.00 .079 1 1.50 .059 C EDGE OF PC BOARD .059 EDGE OF PC BOARD C RECOMMENDED HOLE PATTERN FOR UHM-S110A-5AP1 CONTAINS NO VIAS IN EVEN POSITIONS ON ROW F/Z RECOMMENDED HOLE PATTERN FOR UHM-SXXXB0-5AP1 CONTAINS NO VIAS IN EVEN POSITIONS ON ROW F/Z UHM-S110AX-5AP1-XXXXX DIM. "D" .10 A B C PLATED THRU HOLES B B 66X REVISION UHM-S055BX-5AP1-XXXXX UHM-S095BX-5AP1-XXXXX UHM-S110BX-5AP1-XXXXX UHM-S125BX-5AP1-XXXXX 20.00 .787 78-5100-2533-7 1.50 DRAWING NUMBER A 10X 2.00 .079 F/Z E B 10.00 D .394 C B B A C 11 10 9 8 7 6 5 4 1.50 3 2 1 5X 2.00 .079 .059 EDGE OF PC BOARD UHM-S055CLX-5AP1-XXXXX UHM-S055CRX-5AP1-XXXXX B 58359 DEC 04,2014 JNC TS JNC TS DRFT CHKD REMOVE MRKT FEATURES & WITHSTANDING VOLTAGE WAS 750 A 41080 MAY 24,2012 PRODUCTION RELEASE DESIGN REFERENCE NEXT ASSEMBLY ACCESS CODES A RECOMMENDED PCB MOUNTING HOLE PATTERN (VIEWED FROM COMPONENT SIDE) DIVISION HOLE PLATING TABLE HOLE (FINISHED HOLE) Cu THICKNESS SnPb THICKNESS DRILLED HOLE DIA. DIM. "D" .550-.650 [.0217-.0256] .025-.045 [.0010-.0018] .008-.018 [.0003-.0007] .686-.727 [.0270-.0286] 3 1 THIRD ANGLE PROJECTION INTERPRET PER ASME Y14.5 - 2009 MARKED ONLY 6 5 4 3 CASTIGLIONE MAY 23,2012 CHKD DATE ISD 3M Center INCHES ALL SURFACES 7 ISSUE DATE AND DESCRIPTION DATE St. Paul, TOLERANCES EXCEPT AS NOTED SCALE MAX SURFACE ROUGHNESS 8 ECO DRFT DIVISION CODE Interconnect Solutions DO NOT SCALE DRAWING REV 2 .0 .00 .000 .0000 .01 .005 MILLIMETERS 0 .0 .3 .00 .13 .000 ANGLES MN 55144 MFG DATE APPVL DATE T. SUNIGA MAY 23,2012 C 3M COPYRIGHT 2012 This document and the information it contains are 3M property and may not be reproduced or further distributed without 3M permission, or used or disclosed other than for 3M authorized purposes. All rights reserved. TITLE UHM PRESS-FIT SOCKET, 5-ROW, CONNECTORS CAGE SIZE DRAWING NO. NUMBER REV. 78-5100-2533-7 MODEL DET. LISTS 1 YES NO B SHT 3 OF 3 Imaged: B.1 12/4/2014 2:00 PM UTC-06:00 RECOMMENDED HOLE PATTERN FOR UHM-S055CXX-5AP1 CONTAINS NO VIAS IN EVEN POSITIONS ON ROW F/Z A