PPS-05A-50R0M

POWER SPLITTER – High Precision Power Chip Divider The content of this specification may change without notification 10/23/08 HOW TO ORDER PPS -10 A50R0 M LF Terminal Material SnPb = Leave Blank Lead Free = LF Packaging M = tape/reel 5,000 pcs O = tape/reel 1,000 pcs Impedance 50 Ω Circuit Configuration A or B Size 0402 = 05 0603 = 16 0805 = 10 1206 = 18 2010 = 12 FEATURES High Frequency Splitter is constructed of thin film resistive material Power splitter with excellent high frequency characteristics for applications from DC~20GHz This product has a small reflection feature, allowing for superior in high frequency applications Allows for high density mounting Bit error is restrained by keeping high frequency digital signal stable Series Precision Power Splitter PPS-A ELECTRICAL CHARACTERISTICS Item Size Circuit Configuration Operating Frequency 6 ± 0.5dB Insertion Loss 6 ± 1.0dB Split Deviation 1.3 VSWR 1.5 Input Power at 70°C Max Overload Power Resistance Operating Temperature Packaging PPS-16A 0603 A DC~20GHz DC~10GHz 10~20GHz 0.3dB max DC~10GHz 10~20GHz 100mW 200mW PPS-10 PPS-18A 0805 1206 A A DC~17.5GHz DC~15GHz DC~10GHz DC~10GHz 10~17.5GHz 10~15GHz 0.3dB max 0.3dB max DC~10GHz DC~10GHz 10~17.5GHz 10~15GHz 125mW 250mW 250mW 500mW R1 = R2 = R3 = 50Ω typical -40°C ~ +125°C 1,000/Reel or 5,000/Reel PPS-12A 2010 A DC~10GHz DC~7.5GHz 7.5~10GHz 0.3dB max DC~7.5GHz 7.5~10GHz 500mW 1000mW PPS-B ELECTRICAL CHARACTERISTICS Item Size Circuit Configuration Resistance Tolerance TCR Power Rating per Element Power Rating per Package Rated Operating Temp Resistance Operating Temp. Range Package Quantity PPS-10B 0805 B ±50ppm/°C 33 mW 100 mW 70°C R1 = R2 = R3 = 50Ω typical -55°C ~ +125°C 1,000/Reel or 5,000/Reel PPS-18B 1206 B ±50ppm/°C 42 mW 125 mW CIRCUIT Configuration A Configuration B ±0.1%, ±0.5%, ±1% American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 1 POWER SPLITTER – High Precision Power Chip Divider The content of this specification may change without notification 10/23/08 DERATING CURVE – Circuit A DERATING CURVE – Circuit B DIMENSIONS (mm) Series PPS-05A PPS-16A PPS-10A PPS-18A PPS-12A L 1.00 ± 0.2 1.60 ± 0.2 2.00 ± 0.2 3.20 ± 0.2 0.50 ± 0.2 W 0.50 ± 0.2 0.80 ± 0.2 1.25±0.2 1.60 ± 0.2 2.5 ± 0.2 a 0.4 ± 0.1 0.4 ± 0.1 0.4 ± 0.1 0.3 ± 0.1 0.35 ± 0.1 b 0.30 ± 0.1 0.30 ± 0.1 0.30 ± 0.1 0.35 ± 0.1 0.65 ± 0.1 t 0.4 ± 0.10 0.4 ± 0.10 0.4 ± 0.10 0.4 ± 0.10 0.8 ± 0.15 SCHEMATIC LEGEND 1. 2. 3. 4. 5. Thin Film Resistor Overcoat Resin Terminal (SnPb or Lead Free) Marking (dot to indicate direction & bar) Alumina Substrate SCHEMATIC – Circuit A PERFORMANCE Item Short Time Overload Rated Load Life Moisture Load Life Temperature Cycle Soldering Heat Resistance Strength Between Terminals Solderability Insulation Resistance Test Condition 2.5 times of the rated voltage shall be applied for 5 seconds. Apply rated voltage for 90 min followed by a pause of 30 min at 70±3°C for 1000 hours. The chip divider is applied rated voltage for 90 min at 60±2°C 90～95%RH for 1000 hours. [-55°C (30min)-R.T.(3min)-+125°C(30min)-R.T.(3min)] is repeated 5 cycles. Leave NR in melt solder of 260±5°C for 10±1 seconds. Distance between fulcrums : 90mm; Bending width : 3mm; Substrate: Glass epoxy t=1.6mm Leave NR in melted solder of 235±5°C for 3±0.5 seconds. A minute after 500 DC Tolerance ±0.1% ±0.25% ±0.25% ±0.1% ±0.1% ±0.1% ≥ 1000M Ω ≥95% of the surface should be wet *** Custom Designs Available American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 2