HP30S-CALBL-003

PRODUCT DATASHEET SynJet® PAR30 Cooler 40W (DigiKey Pattern) SynJet cooling technology provides the most reliable thermal management solution available. This LED cooler has been developed by Nuventix for cooling PAR 30 lamps, downlights, spotlights, and tracklights. • • • Cools up to 40 W 4 Reliable 100K Hours Lifetime Energy Efficient • • • 5 yr Warranty Small Form Factor Quiet Low Acoustics Specifications 1 Thermal & Acoustic 2 Θs-a High Performance SynJet Setting 3 4 5 Wire Connections TDP (W) SPL (dBA) 1.00 40 28 Red to +VDC Black & Blue to Ground Standard 1.25 32 22 Red to +VDC Black only to Ground Silent 1.55 26 18 Red to +VDC Black & Purple to Ground PWM at 100% duty cycle 1.00 40 28 Red to +VDC Black only to Ground Blue to PWM Signal Heatsink Only 2.50 16 N/A N/A N/A Electrical SynJet Setting 2 High Performance Standard Silent PWM at 100% duty cycle Current (mA) Voltage (VDC) +/- 10% Imin 5 20 Iavg 140 70 60 140 6 6 Ipeak 280 140 120 280 Pavg (mW) 700 350 300 700 Current (mA) Voltage (VDC) +/- 10% Imin 12 10 Iavg 71 42 38 71 Ipeak 142 84 76 142 Pavg (mW) 850 500 450 850 Environmental All Settings Operating Temperature Storage Temperature Storage Altitude Operating Relative Humidity Weight Reliability Regulatory Compliance Min -40 -50 5 Max 70 95 15K 95 300 100K Units °C °C m % g hrs Conditions Air temperature surrounding cooler Air temperature surrounding cooler Above sea level Non-condensing SynJet with heat sink L10 @ 60°C RoHS, UL, FCC Part 15 Class B, CE 1 All values are typical at 25ºC unless otherwise stated. The Level Select model should be used for discrete performance settings. Follow the instructions in the Product Design Guide for adjusting settings. Thermal resistance values are given as reference only and are measured in free air without airflow obstructions. Thermal resistance is measured from the bottom middle of the heat sink to ambient air measured at the inlet to the SynJet, with a heat source at least 15cm2 using the 40W reference heat sink. Actual thermal performance may vary by application and final product design should be tested to assure proper thermal performance. 4 Thermal Design Power is based on a 40ºC temperature rise of heat sink mounting surface above ambient temperature around cooler. 5 Sound Pressure Level is measured at 1 meter distance per ISO 7779. 6 The SynJet has a time varying current. The current waveform is sinusoidal and the average current (Iavg) is used to calculate the average power consumption (Pavg) at nominal input voltage (VDC). See the Electrical section in the Product Design Guide for a detailed explanation. 2 3 4635 Boston Lane Austin, TX 78735 Phone: 512-382-8100 www.nuventix.com MKTG-DOC-00197 Revision A01 June 2012 PRODUCT DATASHEET Mechanical SynJet Cooling Solution All dimensions are nominal and in mm unless otherwise stated. See product drawings for more detail. SynJet Wire Harness Connector Pinout Pin 1 2 Wire Color Red Black Symbol +VDC GND 3 Purple CTRL2 4 Blue CTRL1 Description 5 V or 12 V depending on model Ground Input for Level Select model Status signal for PWM model Input for Level Select model PWM input for PWM model IMPORTANT: SynJets should be completely wired to the power supply before the power supply is energized. The power supply should be turned off before the SynJet Cooler is disconnected. SynJet Coolers are not designed for “hot swap” or “hot plug” applications. Part Numbers Part Number Description Notes SPARS-CM005-002 SPARS-CM005-001 SPARS-CM012-002 SPARS-CM012-001 HP30S-CALBL-003 WALLS-C4150-001 WALLS-C4600-001 SynJet, ZFlow 65 Cooler, Level Select, 5V, Black SynJet, ZFlow 65 Cooler, PWM, 5V, Black SynJet, ZFlow 65 Cooler, Level Select, 12V, Black SynJet, ZFlow 65 Cooler, PWM, 12V, Black Heatsink, 40W, PAR30 Style, DigiKey Custom, Black Wire Harness, 4-Wire, 150 mm Length Wire Harness, 4-Wire, 600 mm Length Configurable to discrete performance settings Use with PWM input to control performance setting Configurable to discrete performance settings Use with PWM input to control performance setting Contact sales for other heatsink options Contact sales for other wire harness options Contact sales for other wire harness options Nuventix reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or applications. For additional information, please contact Nuventix directly. 4635 Boston Lane Austin, TX 78735 Phone: 512-382-8100 www.nuventix.com MKTG-DOC-00197 Revision A01 June 2012