APTS020A0X43-SRZ

GE Data Sheet 12V TLynxTM 20A: Non-Isolated DC-DC Power Modules 4.5Vdc – 14Vdc; 0.69V to 5.5Vdc output; 20A Output Current Features ▪ Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 (Z versions) ▪ Compatible in a Pb-free or SnPb reflow environment (Z versions) ▪ EZ-SEQUENCETM RoHS Compliant Applications Compliant to REACH Directive (EC) No 1907/2006 ▪ Wide Input voltage range (4.5Vdc-14Vdc) ▪ Output voltage programmable from 0.69Vdc to 5.5 Vdc via external resistor ▪ Tunable LoopTM to optimize dynamic output voltage response ▪ Flexible output voltage sequencing EZ-SEQUENCE (APTS versions) ▪ Fixed switching freqeuency and ability to synchronize with external clock ▪ Distributed power architectures ▪ Intermediate bus voltage applications ▪ Output overcurrent protection (non-latching) ▪ Telecommunications equipment ▪ Overtemperature protection ▪ Servers and storage applications ▪ Remote On/Off ▪ Networking equipment ▪ Remote Sense ▪ Industrial equipment ▪ Power Good signal ▪ Ability to sink and source current ▪ Small size: Vin+ VIN PGOOD Vout+ VOUT SENSE MODULE (1.3 in x 0.53 in x 0.334 in) SEQ Cin CTUNE Q1 ON/OFF 33 mm x 13.46 mm x 8.5 mm RTUNE Co TRIM GND ▪ Wide operating temperature range [-40°C to 85°C] ▪ ANSI/UL* 62368-1 and CAN/ CSA† C22.2 No. 62368-1 Recognized, DIN VDE‡ 0868-1/A11:2017 (EN623681:2014/A11:2017) ▪ ISO** 9001 and ISO 14001 certified manufacturing facilities RTr im Description The 12V TLynxTM series of power modules are non-isolated dc-dc converters that can deliver up to 20A of output current. These modules operate over a wide range of input voltage (VIN = 4.5Vdc-14Vdc) and provide a precisely regulated output voltage from 0.69Vdc to 5.5Vdc, programmable via an external resistor. Features include frequency synchronization, remote On/Off, adjustable output voltage, over current and temperature protection, power good and output voltage sequencing. The Ruggedized version (-D) is capable of operation up to 105°C and withstand high levels of shock and vibration. The Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ February 17, 2021 ©2017 General Electric Corporation. All rights reserved. GE Data Sheet 12V TLynxTM 20A: Non-Isolated DC-DC Power Modules 4.5Vdc –14Vdc input; 0.69Vdc to 5.5Vdc output; 20A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Input Voltage Device Symbol Min Max Unit All VIN -0.3 15 Vdc Continuous Voltage on SEQ terminal All VSEQ -0.3 VIN Vdc Voltage on SYNC terminal All VSYNC -0.3 12 Vdc Voltage on PG terminal All VPG -0.3 6 Vdc Operating Ambient Temperature All TA -40 85 °C All Tstg -55 125 °C (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit 4.5 ⎯ 14 Vdc 20 Adc Operating Input Voltage All VIN Maximum Input Current All IIN,max (VIN = 10.0Vdc, IO = 0, module enabled) VO,set = 0.69 Vdc IIN,No load 42 mA (VIN = 12.0Vdc, IO = 0, module enabled) VO,set = 3.3Vdc IIN,No load 74 mA All IIN,stand-by 3 mA Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN =4.5V to 14V, IO= IOmax ; See Test Configurations) All 43 mAp-p Input Ripple Rejection (120Hz) All 45 dB (VIN=4.5V to 14V, IO=IO, max ) Input No Load Current Input Stand-by Current (VIN = 12.0Vdc, module disabled) A2s 1 CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 20 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. February 17, 2021 ©2017 General Electric Corporation. All rights reserved. Page 2 GE Data Sheet 12V TLynxTM 20A: Non-Isolated DC-DC Power Modules 4.5Vdc –14Vdc input; 0.69Vdc to 5.5Vdc output; 20A Output Current Electrical Specifications (continued) Parameter Device Symbol Min Output Voltage Set-point All VO, set -1.5 Output Voltage All VO, set -2.5 All VO 0.69 Typ ⎯ Max Unit +1.5 % VO, set +2.5 % VO, set 5.5 Vdc (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range (selected by an external resistor) (Some output voltages may not be possible depending on the input voltage – see Feature Descriptions Section) Output Regulation (for VO ≥ 2.5Vdc) Line (VIN=VIN, min to VIN, max) All ⎯ +0.4 % VO, set Load (IO=IO, min to IO, max) All ⎯ 10 mV Line (VIN=VIN, min to VIN, max) All ⎯ 10 mV Load (IO=IO, min to IO, max) All ⎯ 5 mV Temperature (Tref=TA, min to TA, max) All ⎯ 0.5 % VO, set 0.5 Vdc 30 80 mVpk-pk 14 28 mVrms Output Regulation (for VO < 2.5Vdc) Remote Sense Range All Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1μF // 10 μF ceramic capacitors) Peak-to-Peak (5Hz to 20MHz bandwidth) All ⎯ RMS External Capacitance1 Without the Tunable LoopTM All CO, max 0 ⎯ 200 μF ESR ≥ 0.15 mΩ All CO, max 0 ⎯ 1000 μF ⎯ 10000 μF 20 Adc ESR ≥ 1 mΩ With the Tunable LoopTM ESR ≥ 10 mΩ All CO, max 0 Output Current All Io 0 Output Current Limit Inception (Hiccup Mode ) All IO, lim 120 % Io,max Output Short-Circuit Current All IO, s/c 2.6 Adc Efficiency (VIN= 10Vdc) VO,set = 0.69Vdc η 72.1 % VIN= 12Vdc, TA=25°C VO,set = 1.2Vdc η 81.3 % IO=IO, max , VO= VO,set VO,set = 1.8Vdc η 85.7 % VO, set = 2.5Vdc η 88.0 % VO,set = 3.3Vdc η 89.7 % VO,set = 5.0Vdc η 91.8 % (VO≤250mV) ( Hiccup Mode ) 1 External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best transient response. See the Tunable LoopTM section for details. February 17, 2021 ©2017 General Electric Corporation. All rights reserved. Page 3 GE Data Sheet 12V TLynxTM 20A: Non-Isolated DC-DC Power Modules 4.5Vdc –14Vdc input; 0.69Vdc to 5.5Vdc output; 20A Output Current Electrical Specifications (continued) Parameter Switching Frequency Device Symbol Min Typ Max Unit All fsw ⎯ 550 ⎯ kHz 600 kHz Frequency Synchronization Synchronization Frequency Range 520 High-Level Input Voltage All VIH Low-Level Input Voltage All VIL 0.8 V VSYNC=2.5V ISYNC 1 mA All tSYNC 250 ns All tSYNC_SH 250 ns Peak Deviation All Vpk 380 mV Settling Time (Vo