APXH003A0X-SRZ

GE Data Sheet PicoTLynxTM 3A: Non-Isolated DC-DC Power Modules 2.4Vdc –5.5Vdc input; 0.6Vdc to 3.63Vdc output; 3A Output Current Features ▪ Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 (Z versions) ▪ Compatible in a Pb-free or SnPb reflow environment (Z versions) ▪ Compliant to REACH Directive (EC) No 1907/2006 ▪ Wide Input voltage range (2.4Vdc-5.5Vdc) ▪ Output voltage programmable from 0.6Vdc to 3.63 Vdc via external resistor ▪ Tunable LoopTM to optimize dynamic output voltage response ▪ Flexible output voltage sequencing EZ-SEQUENCE – APTH versions Applications ▪ Remote sense ▪ Distributed power architectures ▪ Fixed switching frequency ▪ Intermediate bus voltage applications ▪ Output overcurrent protection (non-latching) ▪ Telecommunications equipment ▪ Overtemperature protection ▪ Servers and storage applications ▪ Remote On/Off ▪ Networking equipment ▪ Ability to sink and source current ▪ Industrial equipment ▪ Cost efficient open frame design ▪ Small size: 12.2 mm x 12.2 mm x 6.25 mm EZ-SEQUENCETM RoHS Compliant Vin+ VIN Vout+ VOUT SENSE MODULE ▪ CTUNE Q1 ON/OFF ▪ RTUNE SEQ Cin Co ▪ TRIM GND (0.48 in x 0.48 in x 0.25 in) Wide operating temperature range (-40°C to 85°C) ANSI/UL* 62368-1 and CAN/ CSA† C22.2 No. 62368-1 Recognized, DIN VDE‡ 0868-1/A11:2017 (EN623681:2014/A11:2017) ISO** 9001 and ISO 14001 certified manufacturing facilities RTrim Description The Pico TLynxTM 3A power modules are non-isolated dc-dc converters that can deliver up to 3A of output current. These modules operate over a wide range of input voltage (V IN = 2.4Vdc-5.5Vdc) and provide a precisely regulated output voltage from 0.6Vdc to 3.63Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and overtemperature protection, and output voltage sequencing (APTH versions). A new feature, the Tunable LoopTM , allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ February 17, 2021 ©2013 General Electric Company. All rights reserved. GE Data Sheet PicoTLynxTM 3A: Non-Isolated DC-DC Power Modules 2.4Vdc –5.5Vdc input; 0.6Vdc to 3.63Vdc output; 3A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Input Voltage Device Symbol Min Max Unit All VIN -0.3 6 Vdc APTH VSEQ -0.3 ViN, Max Vdc All TA -40 85 °C All Tstg -55 125 °C Continuous Sequencing Voltage Operating Ambient Temperature (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 2.4 ⎯ 5.5 Vdc Maximum Input Current All IIN,max 3.5 Adc VO,set = 0.6 Vdc IIN,No load 26 mA VO,set = 3.3Vdc IIN,No load 75 mA All IIN,stand-by 2.1 mA Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN =0 to 5.5V, IO= IOmax ; See Test Configurations) All 25 mAp-p Input Ripple Rejection (120Hz) All 40 dB (VIN=2.4V to 5.5V, IO=IO, max ) Input No Load Current (VIN = 5.0Vdc, IO = 0, module enabled) Input Stand-by Current (VIN = 5.0Vdc, module disabled) 1 A2s CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 5A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. February 17, 2021 ©2013 General Electric Company. All rights reserved. Page 2 GE Data Sheet PicoTLynxTM 3A: Non-Isolated DC-DC Power Modules 2.4Vdc –5.5Vdc input; 0.6Vdc to 3.63Vdc output; 3A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point (with 0.5% tolerance for external resistor used to set output voltage) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation (for VO ≥ 2.5Vdc) Device Symbol Min All VO, set -1.5 All VO, set -3.0 All VO 0.6 Typ ⎯ Max Unit +1.5 % VO, set +3.0 % VO, set 3.63 Vdc Line (VIN=VIN, min to VIN, max) All ⎯ +0.4 % VO, set Load (IO=IO, min to IO, max) All ⎯ 10 mV Line (VIN=VIN, min to VIN, max) All ⎯ 10 mV Load (IO=IO, min to IO, max) All ⎯ 5 mV Temperature (Tref=TA, min to TA, max) All ⎯ 0.4 % VO, set 0.5 V 20 35 mVpk-pk 15 25 mVrms Output Regulation (for VO < 2.5Vdc) Remote Sense Range All Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1μF // 10 μF ceramic capacitors) Peak-to-Peak (5Hz to 20MHz bandwidth) All ⎯ RMS External Capacitance1 Without the Tunable LoopTM All CO, max 0 ⎯ 47 μF ESR ≥ 0.15 mΩ All CO, max 0 ⎯ 1000 μF ESR ≥ 10 mΩ All CO, max 0 ⎯ 3000 μF Output Current All Io 0 Output Current Limit Inception (Hiccup Mode ) All IO, lim Output Short-Circuit Current All IO, s/c 0.12 Adc Efficiency VIN= 3.3Vdc, TA=25°C VO,set = 0.6Vdc VO, set = 1.2Vdc η η 81.2 89.4 % % IO=IO, max , VO= VO,set VO,set = 1.8Vdc η 91.4 % VO,set = 2.5Vdc η 93.9 % VO,set = 3.3Vdc η 94.4 All fsw All All Vpk ts 90 20 mV s All Vpk 100 mV All ts 20 s ESR ≥ 1 mΩ With the Tunable LoopTM 3 Adc 200 % Io,max (VO≤250mV) ( Hiccup Mode ) VIN= 5Vdc Switching Frequency ⎯ 600 % ⎯ kHz Dynamic Load Response (dIo/dt=10A/s; VIN = 5V; Vout = 1.5V, TA=25°C) Load Change from Io= 0% to 50% of Io,max; Co = 0 Peak Deviation Settling Time (Vo