ATA006A0X4-SR

GE Energy Data Sheet 6A Austin MicroLynxTM II: 12V SMT Non-Isolated DC-DC Power Module 8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 6A Output Current RoHS Compliant Features  Compliant to RoHS EU Directive 2011/65/EU (-Z versions)  Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this product will no longer be RoHS compliant (non-Z versions)  Flexible output voltage sequencing EZ-SEQUENCETM  Delivers up to 6A output current  High efficiency – 89% at 3.3V full load (VIN = 12.0V)  Small size and low profile: 27.9 mm x 11.4 mm x 7.24 mm Applications  Distributed power architectures  Intermediate bus voltage applications  Telecommunications equipment  Servers and storage applications  (1.10 in x 0.45 in x 0.285 in)  Low output ripple and noise  High Reliability: Calculated MTBF = 15.3M hours at 25oC Full-load  Output voltage programmable from 0.75 Vdc to 5.5Vdc via external resistor Networking equipment  Line Regulation: 0.3% (typical)  Enterprise Networks  Load Regulation: 0.4% (typical)  Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications  Temperature Regulation: 0.4 % (typical)  Remote On/Off  Output overcurrent protection (non-latching)  Wide operating temperature range (-40°C to 85°C)  UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed  ISO** 9001 and ISO 14001 certified manufacturing facilities Description Austin MicroLynxTM II 12V SMT (surface mount technology) power modules are non-isolated DC-DC converters that can deliver up to 6A of output current with full load efficiency of 89% at 5.0V output. These modules provide precisely regulated output voltage programmable via external resistor from 0.75Vdc to 5.5Vdc over a wide range of input voltage (VIN = 8.3 - 14V). The Austin MicroLynxTM II 12V series has a sequencing feature, EZ-SEQUENCETM that enable designers to implement various types of output voltage sequencing when powering multiple voltages on a board. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ October 1, 2015 ©2012 General Electric Company. All rights reserved. GE Energy Data Sheet 6A Austin MicroLynxTMII: 12V SMT Non-Isolated DC-DC Power Modules 8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 6A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit All VIN -0.3 15 Vdc Sequencing voltage All Vseq -0.3 VIN,max Vdc Operating Ambient Temperature All TA -40 85 °C All Tstg -55 125 °C Input Voltage Continuous (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Vo,set ≤ 3.63 VIN 8.3 12 14 Vdc Vo,set > 3.63 VIN 8.3 12 13.2 Vdc All IIN,max 4.5 Adc VO,set = 0.75 Vdc IIN,No load 17 mA VO,set = 5.0Vdc IIN,No load 100 mA All IIN,stand-by 1.2 mA Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All 30 Input Ripple Rejection (120Hz) All 30 Operating Input Voltage Maximum Input Current Max Unit (VIN= VIN, min to VIN, max, IO=IO, max ) Input No Load Current (VIN = VIN, nom, Io = 0, module enabled) Input Stand-by Current (VIN = VIN, nom, module disabled) 0.4 A2s mAp-p dB CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. October 1, 2015 ©2012 General Electric Company. All rights reserved. Page 2 GE Energy Data Sheet 6A Austin MicroLynxTMII: 12V SMT Non-Isolated DC-DC Power Modules 8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 6A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point Device Symbol Min Typ Max Unit All VO, set -2.0 VO, set +2.0 % VO, set All VO, set -2.5%  +3.5% % VO, set All VO 0.7525 5.5 Vdc (VIN=VIN, min, IO=IO, max, TA=25°C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All  0.3  % VO, set Load (IO=IO, min to IO, max) All  0.4  % VO, set Temperature (Tref=TA, min to TA, max) All  0.4  % VO, set RMS (5Hz to 20MHz bandwidth) All  15 30 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All  30 75 mVpk-pk μF Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Cout = 1μF ceramic//10μFtantalum capacitors) External Capacitance ESR ≥ 1 mΩ All CO, max   1000  3000 μF 6 Adc ESR ≥ 10 mΩ All CO, max  Output Current All Io 0 Output Current Limit Inception (Hiccup Mode ) All IO, lim  200  % Io All IO, s/c  2  Adc VO, set = 1.2Vdc η 80.0 % VIN= VIN, nom, TA=25°C VO,set = 1.5Vdc η 83.0 % IO=IO, max , VO= VO,set VO,set = 1.8Vdc η 83.5 % VO,set = 2.5Vdc η 86.5 % VO,set = 3.3Vdc η 89.0 % (VO= 90% of VO, set) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) Efficiency VO,set = 5.0Vdc η Switching Frequency All fsw  91.0 300  kHz % Switching Frequency (-30 Option) All fsw 288 320 352 kHz All Vpk  200  mV Dynamic Load Response (dIo/dt=2.5A/µs; VIN = VIN, nom; TA=25°C) Load Change from Io= 50% to 100% of Io,max; 1μF ceramic// 10 μF tantalum Peak Deviation Settling Time (Vo