EBVW017A0S14R0641Z

Data Sheet April 16, 2021 EBVW017A0S14R0 Barracuda* Series DC-DC Converter Power Modules 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Features ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Applications ▪ ▪ ▪ Distributed power architectures Intermediate bus voltage applications DSL systems Options ▪ ▪ ▪ Negative Remote On/Off logic (1=option code, factory preferred) Auto-restart after fault shutdown (4=option code, factory preferred) Base plate option (-H=option code) ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Compliant to RoHS EU Directive 2011/65/EC and amended Directive (EU) 2015/863. (-Z versions) Compliant to REACH Directive (EC) No 1907/2006 Compatible with reflow pin/paste soldering process High and flat efficiency profile – 95.4% at 14.0Vdc, 55% load to 90% output Wide Input voltage range: 36-75Vdc Delivers up to 17Adc output current Tightly regulated output voltage Low output ripple and noise No reverse current during prebias start-up or shutdown Industry standard, DOSA compliant, Eight brick: 58.4 mm x 22.8 mm x 11.3 mm (2.30 in x 0.90 in x 0.44 in) Constant switching frequency Positive Remote On/Off logic Output over current/voltage protection Over temperature protection Wide operating temperature range (-40°C to 85°C) ANSI/UL* 62368-1 and CAN/CSA† C22.2 No. 623681 Recognized, DIN VDE‡ 0868-1/A11:2017 (EN62368-1:2014/A11:2017) CE mark 2006/96/EC directives§ Meets the voltage and current requirements for ETSI 300-132-2 and complies with and licensed for Basic insulation 2250 Vdc Isolation tested in compliance with IEEE 802.3¤ PoE standards ISO** 9001 and ISO14001 certified manufacturing facilities Description The EBVW017A0S14R0 series of dc-dc converters are a new generation of DC/DC power modules designed to support 14.0Vdc DSL applications, as distributed power architectures. The EBVW017A0S14R0 series operate from an input voltage range of 36 to 75Vdc, and provide up to 17A output current at 14.0Vdc output voltage, and 240W output power in a DOSA standard eighth brick. The converter incorporates digital control, synchronous rectification technology, and innovative packaging techniques to achieve efficiency reaching 95.5% peak at 14.0Vdc output. This leads to lower power dissipations such that for many applications a heat sink is not required. Standard features include on/off control, output overcurrent and over voltage protection, over temperature protection, input under and over voltage lockout. Optional features include a base plate for heat sink or cold wall applications. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. Builtin filtering for both input and output minimizes the need for external filtering. * Trademark of General Electric Company # UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. ‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V. § This product is intended for integration into end-user equipment . All of the required procedures of end-use equipment should be followed. ¤ IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Incorporated. ** ISO is a registered trademark of the International Organization of Standards. Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the Data Sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Device Symbol Min Max Unit VIN -0.3 75 Vdc 100 Vdc Input Voltage* Continuous Operating transient ≤ 100mS Operating Input transient slew rate, 50VIN to 75VIN (Output may exceed regulation limits, no protective shutdowns shall activate, CO=220μF to CO, max) Non- operating continuous - - 10 V/µs VIN 80 100 Vdc All TA -40 85 °C All Tstg -55 125 °C I/O Isolation Voltage (100% factory Hi-Pot tested) All 2250 ⎯ ⎯ * Input over voltage protection will shutdown the output voltage, when the input voltage exceeds threshold level. Vdc Operating Ambient Temperature (See Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Operating Input Voltage Maximum Input Current (VIN=0V to 75V, IO=IO, max) Input No Load Current Symbol Min Typ Max Unit VIN 36 48 75 Vdc IIN,max - - 7 Adc All IIN,No load All IIN,stand-by 50 mA (VIN = VIN, nom, IO = 0, module enabled) Input Stand-by Current 25 mA (VIN = VIN, nom, module disabled) 100 - - μF - - 1 A2s All - 900 - mArms All - 24 - mAp-p All - 50 - dB External Input Capacitance All Inrush Transient All Input Terminal Ripple Current (Measured at module input pin with maximum specified input capacitance and < 500uH inductance between voltage source and input capacitance CIN=220uF, 5Hz to 20MHz, VIN= 48V, IO= IOmax) Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12μH source impedance; VIN= 48V, IO= IOmax ; see Figure 12) Input Ripple Rejection (120Hz) I2t CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 15 A (see Safety Considerations section). Based on the information provided in this Data Sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s Data Sheet for further information. April 16, 2021 ©2012 General Electric Company. All rights reserved. Page 2 Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Electrical Specifications (continued) Parameter Output Voltage Set-point (VIN=VIN,nom, IO=10A, TA =25°C) Output Voltage (Over all operating input voltage(40V to 75V), resistive load, and temperature conditions until end of life) Output Voltage (VIN=36V, TA = 25ºC) Device Symbol Min Typ Max Unit All VO, set 13.97 14.00 14.03 Vdc All VO 13.71 ⎯ 14.29 Vdc All VO 10.8 ⎯ ⎯ Vdc % VO, set Output Regulation (VIN, min=46V) Line (VIN=VIN, min to VIN, max) All ⎯ 0.2 ⎯ Load (IO=IO, min to IO, max) All ⎯ 0.2 ⎯ Temperature (TA = -40ºC to +85ºC) All ⎯ 2 ⎯ RMS (5Hz to 20MHz bandwidth) All ⎯ 70 ⎯ mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All ⎯ 200 ⎯ mVpk-pk 220 ⎯ % VO, set % VO, set Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max, tested with a 1.0 μF ceramic, 10 μF aluminum and 220μF polymer capacitor across the load.) CO All Output Current All Io 0 Output Current Limit Inception All IO, lim ⎯ IO= 100% IO, max All η 95.5 % IO= 40% - 100% IO, max All η 94.0 % fsw 150 kHz 19 10,000 μF External Output Capacitance 17 Adc ⎯ Adc Efficiency (VIN=VIN, nom, VO= VO,set, TA=25°C) Switching Frequency (primary MOSFETs) (Output Ripple 2X switching frequency) Dynamic Load Response (dIo/dt=1A/10s; Vin=Vin,nom; TA=25°C; tested with a 10 μF ceramic and 1x 470μF polymer capacitor across the load.) Load Change from Io= 50% to 75% of Io,max: Peak Deviation Settling Time (Vo 2000mm3), Peak temperature over 245C is not suggested due to the potential reliability risk of components under continuous high-temperature. Min. sustain duration above 217C : 90 seconds Min. sustain duration above 180C : 150 seconds Max. heat up rate: 3C/sec Max. cool down rate: 4C/sec In compliance with JEDEC J-STD-020C spec for 2 times reflow requirement. Pb-free Reflow Profile BMP module will comply with J-STD-020 Rev. C (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. BMP will comply with JEDEC J-STD-020C specification for 3 times reflow requirement. The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Figure 23. April 16, 2021 Temp The RoHS-compliant, Z version, through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. The non-Z version products use lead-tin (Pb/Sn) solder and RoHS-compliant components. Both version modules are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant, pure tin finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210C. For Pb solder, the recommended pot temperature is 260C, while the Pb-free solder pot is 270C max. Not all RoHS-compliant throughhole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your GE representative for more details. Peak Temp. 240-245°C Ramp down max. 4°C/Sec 217°C 200°C Time Limited 90 Sec. above 217°C 150°C Preheat time 100-150 Sec. Ramp up max. 3°C/Sec 25°C Time Figure 23. Recommended linear reflow profile using Sn/Ag/Cu solder. MSL Rating The EBVW017A0S14R0 modules have a MSL rating as indicated in the Device Codes table, last page of this document. Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of 30°C and 60% relative humidity varies according to the MSL rating (see J-STD025A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40° C, < 90% relative humidity. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to GE Board Mounted Power Modules: Soldering and Cleaning Application Note (AP01-056EPS). ©2012 General Electric Company. All rights reserved. Page 10 Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current EMC Considerations The circuit and plots in Figure 24 shows a suggested configuration to meet the conducted emission limits of EN55032 Class B. For further information on designing for EMC compliance, please refer to the FLT007A0 data sheet. L e v e l[ d B µ V ] 8 0 7 0 6 0 + x 5 0 + x + x 4 0 3 0 x x x + + + 2 0 1 0 0 1 5 0 k 3 0 0 k 5 0 0 k 1 M 2 M 3 M 4 M5 M F r e q u e n c y[ H z ] 7 M 1 0 M 3 0 M x xM E S C E 0 9 1 6 1 1 1 9 5 2 _ f i nQ P + +M E S C E 0 9 1 6 1 1 1 9 5 2 _ f i nA V M E S C E 0 9 1 6 1 1 1 9 5 2 _ p r eP K M E S C E 0 9 1 6 1 1 1 9 5 2 _ p r eA V Figure 24. EMC Considerations. Packaging Details All versions of the EBVW017A0S14R0 are supplied as standard in the plastic trays shown in Figure 25. Tray Specification Material Max surface resistivity Color Capacity Min order quantity PET (1mm) Each tray contains a total of 18 power modules. The trays are self-stacking and each shipping box for the EBVW017A0S14R0 module contains 2 full trays plus one empty hold-down tray giving a total number of 36 power module 109 -1011/PET Clear 18 power modules 36 pcs (1 box of 2 full trays + 1 empty top tray) Open Frame Module Tray April 16, 2021 ©2012 General Electric Company. All rights reserved. Base Plate Module Tray Page 11 Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Figure 25. EBVW020 Packaging Tray April 16, 2021 ©2012 General Electric Company. All rights reserved. Page 12 Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Mechanical Outline for EBVW017A0S14R0 Through-hole Module Dimensions are in millimeters and [inches]. Tolerances: x.x mm  0.5 mm [x.xx in.  0.02 in.] (Unless otherwise indicated) x.xx mm  0.25 mm [x.xxx in  0.010 in.] Top side label includes GE name, product designation and date code. Top View* Side View *For optional pin lengths, see Table 2, Device Coding Scheme and Options Bottom View Pin 1 2 3 4 8 April 16, 2021 Function Vi(+) ON/OFF Vi(-) Vo(-) Vo(+) ©2012 General Electric Company. All rights reserved. Page 13 Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Mechanical Outline for EBVW017A0S14R0–H (Baseplate version) Through-hole Module Dimensions are in millimeters and [inches]. Tolerances: x.x mm  0.5 mm [x.xx in.  0.02 in.] (Unless otherwise indicated) x.xx mm  0.25 mm [x.xxx in  0.010 in.] Top View Side View *For optional pin lengths, see Table 2, Device Coding Scheme and Options * Bottom side label includes GE name, product designation and date Bottom View* Pin 1 2 3 4 8 April 16, 2021 Function Vi(+) ON/OFF Vi(-) Vo(-) Vo(+) ©2012 General Electric Company. All rights reserved. Page 14 Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Recommended Pad Layouts Dimensions are in millimeters and (inches). Tolerances: x.x mm  0.5 mm ( x.xx in.  0.02 in.) [unless otherwise indicated] x.xx mm  0.25 mm ( x.xxx in  0.010 in.) Through-Hole Modules Pin Pin Number Name 1* VIN(+) 2* ON/OFF 3* VIN(-) 4* VOUT(-) 8* VOUT(+) April 16, 2021 ©2012 General Electric Company. All rights reserved. Page 15 Data Sheet April 16, 2021 EBVW017A0S14R0 Series Power Modules; DC-DC Converters 36-75Vdc Input; 14.0Vdc Output; 17A Output Current Ordering Information Please contact your GE Sales Representative for pricing, availability and optional features. Table 1. Device Codes Product codes Input Voltage EBVW017A0S14R0641Z 48V (36−75Vdc) Output Output Efficiency Voltage Current 14.0V 17A 95.5% Connector Type MSL Rating Comcodes Through hole 2a 150022524 Table 2. Device Options Contact Us For more information, call us at USA/Canada: +1 888 546 3243, or +1 972 244 9288 Asia-Pacific: +86-21-53899666 Europe, Middle-East and Africa: +49.89.878067-280 Go.ABB/Industrial GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. April 16, 2021 ©2012 General Electric Company. All rights reserved. Version 1_2