ESTW004A2C41-HZ

GE Data Sheet ESTW004A2C Stingray* Series; DC-DC Converter Power Modules 36–75Vdc Input; 15.0Vdc/4.2Adc Output Features ▪ Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 (-Z versions) ▪ Compliant to REACH Directive (EC) No 1907/2006 ▪ Industry standard, DOSA compliant footprint 57.9mm x 22.8mm x 7.6mm (2.28 in x 0.9 in x 0.30 in) ▪ Low profile height and reduced component skyline ▪ Wide input voltage range: 36-75 Vdc ▪ Tightly regulated output ▪ Remote sense ▪ Output Voltage adjust: 80% to 110% of Vo,nom ▪ Constant switching frequency Applications ▪ Positive remote On/Off logic ▪ Wireless Networks ▪ Input under/over voltage protection ▪ Access and Optical Network Equipment ▪ Output overcurrent and overvoltage protection ▪ ▪ Industrial Equipment Over-temperature protection ▪ No reverse current during output shutdown ▪ Wide operating temperature range (-40°C to 85°C) ▪ Suitable for cold wall cooling using suitable Gap Pad applied directly to top side of module ▪ ANSI/UL* 62368-1 and CAN/CSA† C22.2 No. 62368-1 Recognized, DIN VDE‡ 0868-1/A11:2017 (EN623681:2014/A11:2017) RoHS Compliant Options ▪ Negative Remote On/Off logic (preferred) ▪ CE mark meets 2014/35/EU directive§ ▪ Over current/Over voltage protections (Auto-restart) (preferred) ▪ Meets the voltage and current requirements for ETSI 300-1322 and complies with and licensed for Basic insulation rating ▪ Heat plate version (-H) ▪ 2250 Vdc Isolation tested in compliance with IEEE 802.3¤ PoE standards ▪ ISO**9001 and ISO 14001 certified manufacturing facilities Description The ESTW004A2C Series, eighth-brick, low-height power modules are isolated dc-dc converters that provide a single, precisely regulated output voltage over a wide input voltage range of 36-75Vdc. The ESTW004A2C provides 15Vdc nominal output voltage rated for 4.2Adc output current. The module incorporates GE’s vast heritage for reliability and quality, while also using the latest in technology, and component and process standardization to achieve highly competitive cost. The open frame module construction, available in through-hole packaging, enable designers to develop cost and space efficient solutions. The module achieves typical full load efficiency greater than 90% at VIN=48Vdc. Standard features include remote On/Off, remote sense, output voltage adjustment, overvoltage, overcurrent and overtemperature protection. An optional heat plate allows for external standard, eighth-brick heat sink attachment to achieve higher output current in high temperature applications. * Trademark of General Electric Company. # UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. ‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V. § This product is intended for integration into end-user equipment . All of the required procedures of end-use equipment should be followed. ¤ IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Incorporated. ** ISO is a registered trademark of the International Organization of Standards † April 22, 2021 ©2016 General Electric Company. All rights reserved. Page 1 GE Data Sheet ESTW004A2C Stingray Series DC-DC Converter Power Modules 36–75Vdc Input; 15.0Vdc/4.2Adc Output Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage Continuous All VIN -0.3 80 Vdc Transient, operational (≤100 ms) All VIN,trans -0.3 100 Vdc All TA -40 85 °C Storage Temperature All Tstg -55 125 °C I/O Isolation voltage (100% factory Hi-Pot tested) All ⎯ ⎯ 2250 Vdc Operating Ambient Temperature (see Thermal Considerations section) Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Maximum Input Current (VIN= VIN, min to VIN, max, IO=IO, max) Input No Load Current (VIN = 48V, IO = 0, module enabled) Input Stand-by Current Device Symbol Min Typ Max Unit All VIN 36 48 75 Vdc All IIN,max 2.0 Adc All IIN,No load 90 IIN,stand-by 5 All (VIN = 48V, module disabled) I2t mA 8 mA 0.5 A2s Inrush Transient All Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All 30 mAp-p Input Ripple Rejection (120Hz) All 50 dB CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architectures. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 10 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. April 22, 2021 ©2016 General Electric Company. All rights reserved. Page 2 GE Data Sheet ESTW004A2C Stingray Series DC-DC Converter Power Modules 36–75Vdc Input; 15.0Vdc/4.2Adc Output Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit All VO, set 14.7 15.0 15.3 Vdc All VO 14.55 ⎯ 15.45 Vdc All All All ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ±0.2 ±0.2 ±1.0 % VO, set % VO, set % VO, set All ⎯ 35 60 mVrms All ⎯ 100 180 mVpk-pk Nominal Output Voltage Set-point VIN= 48V IO=IO, max, TA=25°C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Output Regulation Line (VIN=VIN, min to VIN, max) Load (IO=IO, min to IO, max) Temperature (Tref=TA, min to TA, max) Output Ripple and Noise (VIN=48V, IO= IO, max, TA=25°C, see Figure 7.) RMS (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) External Capacitance All CO, max 0 ⎯ 2,000 μF Output Current All IO 0 ⎯ 4.2 Adc Output Power (IO ≤ IO, max) Output Current Limit Inception (Hiccup Mode ) (VO= 90% of VO, set) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) Efficiency All PO 0 ⎯ 63 W All IO, lim 4.6 5.2 6.0 Adc All IO, s/c 5 Arms VIN=48V, TA=25°C, IO=2.1A, VO = 15V All η 88.0 % VIN=48V, TA=25°C, IO=4.2A, VO= 15V All η 90.0 % All fsw 280 kHz All Vpk ⎯ 3 ⎯ % VO, set All ts ⎯ 200 ⎯ s Device Symbol Min Typ Max Unit Switching Frequency Dynamic Load Response (dIo/dt=0.1A/s; VIN = 48V; TA=25°C) Load Change from Io= 50% to 75% or 25% to 50% of Io,max Peak Deviation Settling Time (Vo