EVW020A0S6R041Z

GE Data Sheet EVW020A0S6R0 Series (Eighth-Brick) DC-DC Power Modules 36–75Vdc Input; 6.0Vdc Output; 20A Output Current Features RoHS Compliant  Compliant to RoHS EU Directive 2011/65/EU (Z versions)  Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this produc twill no longer be RoHS compliant (non-Z versions)  Compliant to IPC-9592, Category 2, Class II  High efficiency 92% at 6.0Vdc full load (Vin=48Vdc)  Industry standard, DOSA compliant footprint 58.4 mm x 22.8 mm x 8.1 mm (2.30 in x 0.9 in x 0.32 in) Applications  Automated Test Equipment  Wireless PA Pre-amps  Precision Instruments Options  Negative Remote On/Off logic (preferred)  Over current/Over temperature/Over voltage protections (Auto-restart) (preferred)  Heat plate version (-H)  Surface Mount version (-S)  Trimmed pin lengths  Wide input voltage range: 36-75 Vdc  Tightly regulated output  Constant switching frequency  Positive remote On/Off logic  Input under/over voltage protection  Output overcurrent and overvoltage protection  Over-temperature protection  Remote sense  No reverse current during output shutdown  Output Voltage adjustment range: 5.0Vdc to 7.0Vdc  Wide operating temperature range (-40°C to 85°C)  ANSI/UL* 60950-1, 2nd Ed. Recognized, CSA† C22.2 No. 60950-1-07 Certified, and VDE‡ 0805-1 (EN60950-1, 2nd Ed.) Licensed  CE mark meets 2006/95/EC directive§  Meets the voltage and current requirements for ETSI 300-132-2 and complies with and licensed for Basic insulation rating per EN60950-1  2250 Vdc Isolation tested in compliance with IEEE 802.3¤ PoE standards  ISO**9001 and ISO 14001 certified manufacturing facilities Description The EVW020A0S6R0, Eighth-brick low-height power module is an isolated dc-dc converters that can deliver up to 20A of output current and provide a precisely regulated output voltage of 6.0Vdc over a wide range of input voltages (VIN = 36 75Vdc). The modules achieve typical full load efficiency of 92%. The module offers wide output voltage trim (5.0Vdc to 7.0Vdc), allowing designers to use the module with a wide variety of output LDOs for final load voltage. The open frame modules construction, available in both surface-mount and through-hole packaging, enable designers to develop cost and space efficient solutions. Standard features include remote On/Off, remote sense, output voltage adjustment, overvoltage, overcurrent and overtemperature protection. October 2, 2015 ©2012 General Electric Company. All rights reserved. GE Data Sheet EVW020A0S6R0 Series (Eighth-Brick) DC-DC Power Modules 36–75Vdc Input; 6.0Vdc Output; 20A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage Continuous All VIN -0.3 80 Vdc Transient, operational (≤100 ms) All VIN,trans -0.3 100 Vdc All TA -40 85 °C Storage Temperature All Tstg -55 125 °C I/O Isolation voltage (100% factory Hi-Pot tested) All   2250 Vdc Operating Ambient Temperature (see Thermal Considerations section) Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Maximum Input Current (VIN= VIN, min to VIN, max, IO=IO, max) Input No Load Current (VIN = VIN, nom, IO = 0, module enabled) Input Stand-by Current Device Symbol Min Typ Max Unit All VIN 36 48 75 Vdc All IIN,max 3.7 4.1 Adc All IIN,No load 90 IIN,stand-by 3.2 All (VIN = VIN, nom, module disabled) I2t mA 4.0 mA 0.5 A2s Inrush Transient All Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All 20 mAp-p Input Ripple Rejection (120Hz) All 52 dB CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architectures. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. October 2, 2015 ©2012 General Electric Company. All rights reserved. Page 2 GE Data Sheet EVW020A0S6R0 Series (Eighth-Brick) DC-DC Power Modules 36–75Vdc Input; 6.0Vdc Output; 20A Output Current Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit All VO, set 5.88 6.0 6.15 Vdc All VO 5.82  6.21 % VO, set All All All       ±0.2 ±0.2 ±0.2 % VO, set % VO, set % VO, set Output Ripple and Noise on nominal output (VIN=VIN, nom ,IO= IO, max , TA=TA, min to TA, max) RMS (5Hz to 20MHz bandwidth) All  15 25 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All 75 mVpk-pk Nominal Output Voltage Set-point VIN=VIN, min, IO=IO, max, TA=25°C) Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Output Regulation Temperature (Tref=TA, min to TA, max) Line (VIN=VIN, min to VIN, max) Load (IO=IO, min to IO, max)  40 External Capacitance All CO, max 0  10,000 μF Output Current Output Current Limit Inception (Hiccup Mode ) (VO= 90% of VO, set) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) Efficiency All Io 0  20 Adc All IO, lim 105 120 130 % Io All IO, s/c 5 VIN= VIN, nom, TA=25°C, IO=IO, max , VO= VO,set All η 92.0 % VIN= VIN, nom, TA=25°C, IO=0.5xIO, max , VO= VO,set All η 91.0 % All fsw 400 kHz Switching Frequency 90.0 Arms Dynamic Load Response (dIo/dt=0.1A/s; VIN = VIN, nom; TA=25°C) Load Change from Io= 50% to 75% or 25% to 50% of Io,max Peak Deviation Settling Time (Vo