FNPAFS21/2M

Technical Data Sheet 201712 Page 1 Non-Metallic Systems PAS Standard Weight Conduit Technical Characteristics Conforms to BSI Kitemark KM-35161 CE Mark to the Low voltage directive 2014/35/EU Deutsche Bahn S4, SR2, ST2 NFR 16-10 1 I3,F3 UL Recognised to UL1696 File number E173968 Approvals and Standards Degree of mechanical protection High flexibility & fatigue life Degree of protection IP40 - Adaptaring & Jumbo IP65 - Jumbo + SK Seal IP66 - Adaptalok, ATS or Adaptaseal IP67 - Adaptalok + ALS Seal or ATS, Adaptaseal IP68 - Adaptalok + ALS Seal or ATS, Adaptaseal IP69k - Adaptalok + ALS Seal or ATS UV protection Very High Finish Black (BL), Grey (GR) Application Indoors / Outdoors - light industrial, buildings & machinery Normal operating temperature range Application Min Temp For use with - Fitting range Fire performance Max Temp Static - 40°C +120°C Dynamic - 5°C +120 °C Adaptalok & ATS, Adaptaseal, Adaptaring and Jumbo fittings Test Standard Performance Rating BS EN 61386 Pass NFF16-101 I3 F3 DIN5510-2 S4 SR2 ST2 UL94 V2 Testing data Click or See pages 3 & 4 Type of material Polyamide (Nylon) 6 - flame retardant - heat stabilised Self Extinguishing & Halogen Free Image Cable Management Products Ltd. CMG House - Station Road - Coleshill - B46 1HT - United Kingdom Tel: +44(0)1675 468 222 - Fax: +44(0)1675 464 930 Technical Support e-mail: cmg.conduitsystems@tnb.com - www.adaptaflex.com The Company’s policy is one of continuous improvement and reserves the right to change specifications at any time without prior notice. Technical Data Sheet 201712 Page 2 Non-Metallic Systems PAS Standard Weight Conduit Technical & Dimensional Data Conduit Size Dimensions NW Conduit Conduit Size Pitch (A) Outside (B) Inside Diameter Diameter Average (C) Min. Bend Reel Weight Radius Length (m) (Kg/100m) **PAFS10 10mm 7.5 Fine 10.0mm 6.5mm 15mm 50 1.9 **PAFS13 13mm 10 Fine 13.0mm 9.6mm 25mm 50 2.8 PAFS16 16mm 13 Fine 15.8mm 11.8mm 35mm 50 3.9 PAFS18 18mm 15 Fine 18.4mm 14.0mm 40mm 50 4.9 PAFS21 21mm 17 Fine 21.2mm 16.5mm 45mm 50 6.1 PACS25 25mm 22 Coarse 25.0mm 19.8mm 50mm 50 8.0 PAFS28 28mm 23 Fine 28.5mm 22.6mm 50mm 50 10.2 PACS28 28mm 23 Coarse 28.5mm 21.7mm 50mm 50 10.0 PAFS34 34mm 29 Fine 34.5mm 28.8mm 60mm 50 13.5 PACS34 34mm 29 Coarse 34.5mm 27.7mm 60mm 50 13.5 PACS42 42mm 36 Coarse 42.5mm 35.2mm 65mm 25 16.8 PACS48 48mm 42 Coarse 48.2mm 40.9mm 70mm 25 18.8 PACS54 54mm 48 Coarse 54.5mm 46.5mm 75mm 25 24.1 PACS80 80mm 70 Coarse 79.3mm 67.0mm 160mm 10 48.0 95 Coarse 106mm 91.5mm 210mm 10 85.0 Part No. Nominal Conduit Size PACS106 106mm To order quote part number, colour & reel length, e.g PAFS21/BL/50M **UR mark not applicable to sizes 10 and 13. Cable Management Products Ltd. CMG House - Station Road - Coleshill - B46 1HT - United Kingdom Tel: +44(0)1675 468 222 - Fax: +44(0)1675 464 930 Technical Support e-mail: cmg.conduitsystems@tnb.com - www.adaptaflex.com The Company’s policy is one of continuous improvement and reserves the right to change specifications at any time without prior notice. Technical Data Sheet 201712 Page 3 Non-Metallic Systems PAS Standard Weight Conduit BS EN 61386 Classification PA S Fitting Compression Impact Min temp Max temp bending electrical IP solids IP water ATS 2 4 2 4 4 0 6 7 Corrosion Tensile - 1 Non-flame Propogating Suspended load 1 0 Mechanical Properties Test Type Methods / Standards Requirements Value Crush Strength BS EN 61386 90% recovery >320N Impact Strength @ 23 °C BS EN 61386-1 No Cracks 20J Impact Strength @-5 °C BS EN 61386-1 No Cracks. 6.0J Tensile Strength BS EN 61386-1 Pull off of fitting minimum value >100N Dynamic Bend radius @-5 °C BS EN 61386-23 5000 cycles minimum 4xOD Test Type Methods / Standards Requirements Value Minimum Temp Dynamic BS EN 61386 Dynamic 5000 cycles -5°C Maximum Short Term Temp BS EN 61386 Static & Dynamic 3000 hours, 5000 cycles 150°C Minimum Static Temp Permanent Use (30,000) Hours -40°C Maximum Static Temp Permanent Use (30,000) Hours 120°C 2xOD Pass Thermal Properties Cold Bend @ - 40°C NFR13-903 Chemical Resistance Chart Key: Suitable : Limited Suitability : Unsuitable : Not Tested : The information above is given as a guide only and is based on published technical data and experience. The chemical resistance of the above products is dependant on factors such as chemical exposure, concentration of the chemical and temperature. The above chemicals are valid for a temperature of 23°C. Use of the above table is at the users own discretion and risk. Those using it must satisfy themselves that their application presents no health and safety risks. The end user should assess compatibility with their application and contact Thomas & Betts for further information. ADHERENCE TO THE CURRENT WIRING REGULATIONS BS7671 OR NEC WIRING REGULATIONS (FOR USA) IS STRONGLY ADVISED. MINIMUM BEND RADIUS FOR FLEXING IS DEPENDANT UPON MINIMUM TEMPERATURE, BENDING FREQUENCY AND CHEMICAL ENVIRONMENT. Cable Management Products Ltd. CMG House - Station Road - Coleshill - B46 1HT - United Kingdom Tel: +44(0)1675 468 222 - Fax: +44(0)1675 464 930 Technical Support e-mail: cmg.conduitsystems@tnb.com - www.adaptaflex.com The Company’s policy is one of continuous improvement and reserves the right to change specifications at any time without prior notice. Technical Data Sheet 201712 Page 4 Non-Metallic Systems PAS Standard Weight Conduit Flammability Test Type Method / Standard Requirement Result Unit Oxygen Index ISO 4589-2 % Oxygen to support combustion 28.9 % Glow Wire Rating IEC 60695 No Ignition to Extinguish with 30s 850 °C Flammability UL94 Vertical (V0) or Horizontal (HB) V2 HB-V0 Flammability BS EN 61386-1 1Kw Burner @ 45° Vertical burn Pass Pass/Fail NF F16-101 Glow Wire & oxygen index I3 - Ignition Rating Smoke Test Type Method / Standard Fume Rating Requirement Result Unit NF F16-101 Smoke & Toxicity F3 - Smoke Density BS6853 A