HW010A0G1-S

GE Data Sheet HW006/010/012 Series Power Modules; dc-dc Converters 36-75Vdc Input; 1.2 Vdc to 5 Vdc Output; 6.6A to 12A Features RoHS Compliant  Compliant to RoHS EU Directive 2011/65/EU (Z versions)  Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this produc twill no longer be RoHS compliant (non-Z versions)  Delivers up to 6A Output current 5V (4A), 3.3V (5A), 2.5V – 1.0V (6A each) Applications  High efficiency – 89% at 5.0V full load  Low Output voltage- supports migration to future IC supply voltages down to 1.0V  Low output ripple and noise  Small Size and low profile  Wireless Networks  Distributed power architectures  Optical and Access Network Equipment  Enterprise Networks  Surface mount or Through hole (TH)  Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications  Remote On/Off  Output overcurrent/Over voltage protection  Over temperature protection  Single Tightly regulated output  Output voltage adjustment trim 10% 47.2mm x 29.5mm x 8.5mm (1.86 x 1.16 x 0.335 in) Options  Remote On/Off logic (positive or negative)  Surface Mount (-S Suffix)  Wide operating temperature range (-40°C to 85°C)  Additional Vout+ pin (-3 Suffix)  Meets the voltage insulation requirements for ETSI 300132-2 and complies with and is Licensed for Basic Insulation rating per EN 60950  CE mark meets 73/23/EEC and 93/68/EEC directives§  UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed  ISO** 9001 and ISO 14001 certified manufacturing facilities Description The HW/HC series power modules are isolated dc-dc converters that operate over a wide input voltage range of 18 to 36 Vdc (HC) or 36 to 75 Vdc (HW) and provide one precisely regulated output. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency, e.g. typical efficiency of 87% 3.3V/5A, 86% at 2.5V/6A. Built-in filtering for both input and output minimizes the need for external filtering. These open frame modules are available either in surface-mount (-S) or in through-hole form. * UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards ‡ October 2, 2015 ©2012 General Electric Company. All rights reserved. GE Data Sheet HW006/010/012 Series Power Modules; dc-dc Converters 36-75Vdc Input; 1.2 Vdc to 5 Vdc Output; 6.6A to 12A Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Vdc Input Voltage HC VIN -0.3 50 Continuous HW VIN -0.3 80 Vdc Transient (100ms) HW VIN, trans -0.3 100 Vdc All TA -40 85 °C Storage Temperature All Tstg -55 125 °C I/O Isolation Voltage (100% factory tested) All   2250 Vdc Operating Ambient Temperature (see Thermal Considerations section) Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Operating Input Voltage Device Symbol Min Typ Max Unit Vdc HC VIN 18 24 36 HW VIN 36 54 75 Vdc Maximum Input Current HC IIN,max 1.75 Adc (VIN=0V to 75V, IO=IO, max) HW IIN,max 0.85 Adc Inrush Transient All It 1 A2s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12μH source impedance; VIN=0V to 75V, IO= IOmax ; see Figure 9) All 5 mAp-p Input Ripple Rejection (120Hz) All 50 dB EMC, EN55022 2 See EMC Considerations section CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 3A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. October 2, 2015 ©2012 General Electric Company. All rights reserved. Page 2 GE Data Sheet HW006/010/012 Series Power Modules; dc-dc Converters 36-75Vdc Input; 1.2 Vdc to 5 Vdc Output; 6.6A to 12A Electrical Specifications (continued) Parameter Output Voltage Set-point (VIN=VIN,nom, IO=IO, max, Tref=25°C) Output Voltage Device Symbol Min Typ Max Unit 5V, 3.3V 2.5V, 2.0V, 1.8V, 1.5V VO, set -1.0  +1.0 % VO, nom 1.2V, 1.0V VO, set -1.25  +1.25 % VO, nom All VO -3.0  +3.0 % VO, nom All VO -10.0 +10.0 % VO, nom 10 mV (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All   Load (IO=IO, min to IO, max) All   15 mV Temperature (Tref=TA, min to TA, max) All   1.00 % RMS (5Hz to 20MHz bandwidth) All  8 15 mVrms Peak-to-Peak (5Hz to 20MHz bandwidth) All Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max)  25 50 mVpk-pk External Capacitance All CO, max   470 μF Output Current 5V Io 0 4.0 Adc 3.3V Io 0 5.0 Adc 2.5V, 2.0, 1.8V, 1.5V, 1.2V, 1.0V Io 0 6.0 Adc 5V IO, lim  6.5  Adc 3.3V IO, lim  7  Adc 2.5V, 2.0V, 1.8V, 1.5V, 1.2V, 1.0V IO, lim  8.5  Adc Output Current Limit Inception ( Hiccup Mode ) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) October 2, 2015 5V IO, s/c  2.4  A rms 3.3V IO, s/c  2.4  A rms 2.5V, 2.0V, 1.8V, 1.5V, 1.2V, 1.0V IO, s/c  2.8  A rms ©2012 General Electric Company. All rights reserved. Page 3 GE Data Sheet HW006/010/012 Series Power Modules; dc-dc Converters 36-75Vdc Input; 1.2 Vdc to 5 Vdc Output; 6.6A to 12A Electrical Specifications (continued) Parameter Efficiency Device Symbol Min Typ Max Unit HW 5V η  89.0  % HW 3.3V η  87.0  % VIN=VIN, nom, TA=25°C HW 2.5V η  86.0  % IO=IO, max , VO= VO,set HW 2.0V η  82.0  % HW 1.8V η  82.0  % HW 1.5V η  80.0  % HW 1.2V η  77.0  % HW 1.0V η  75.0  % % HC 5V η  88.0  HC 3.3V η  86.0  % All HW fsw  300  kHz All HC fsw  380  kHz 5V, 3.3V Vpk  100  mV 2.5V, 2.0V, 1.8V, 1.5V, 1.2V, 1.0V Vpk  80  mV All ts  100  s Peak Deviation All Vpk  0.6 2 %Vo, set Settling Time (Vo