KW015A0F41Z

GE Data Sheet KW010/015/020/025 Series Power Modules 36 – 75Vdc Input; 1.2 to 5.0Vdc Output; 10 to 25A Output current RoHS Compliant Features Representative Photo, actual product may vary. Applications  Compliant to RoHS EU Directive 2011/65/EU (Z versions)  Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this produc twill no longer be RoHS compliant (non-Z versions)  Delivers up to 25A output current 5V(10A), 3.3V(15A), 2.5V(20A), 1.8V-1.2V(25A)  High efficiency – 91% at 3.3V full load  Small size and low profile: 33.0 mm x 22.9 mm x 8.5 mm (1.30 in x 0.9 in x 0.335 in)  Distributed power architectures  Wireless networks  Industry standard DOSA footprint  Access and optical network Equipment  -20% to +10% output voltage adjustment trim  Enterprise Networks  Remote On/Off  Latest generation IC’s (DSP, FPGA, ASIC) and Microprocessor powered applications  Remote Sense  No reverse current during output shutdown  Over temperature protection (latching)  Output overcurrent/overvoltage protection (latching)  Wide operating temperature range (-40°C to 85°C)  Meets the voltage isolation requirements for ETSI 300-132-2 and complies with and is licensed for Basic Insulation rating per EN60950-1  UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03 Certified, and VDE‡ 0805 (IEC60950 3rd Edition) Licensed  CE mark meets 2006/95/EC directive§  ISO** 9001 and ISO 14001 certified manufacturing facilities Options  Negative Remote On/Off logic  Surface Mount (Tape and Reel, -SR Suffix)  Over current/Over temperature/Over voltage protections (auto-restart)  Shorter lead trim Description The KW (Sixteenth-brick) series power modules are isolated dc-dc converters that operate over a wide input voltage range of 36 to 75Vdc and provide a single precisely regulated output. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency, typical efficiency of 91% for 3.3V/15A. These open frame modules are available either in surface-mount (-SR) or in through-hole (TH) form. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. ‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V. § This product is intended for integration into end-use equipment. All of the required procedures of end-use equipment should be followed ** ISO is a registered trademark of the International Organization of Standards † October 5, 2015 ©2012 General Electric Company. All rights reserved. GE Data Sheet KW010/015/020/025 Series Power Modules 36 – 75Vdc Input; 1.2 to 5.0Vdc Output; 10 to 25A Output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage Continuous All VIN -0.3 80 Vdc Transient (100 ms) All VIN,trans -0.3 100 Vdc All TA -40 85 °C Storage Temperature All Tstg -55 125 °C I/O Isolation voltage (100% Factory Hi-Pot tested) All   1500 Vdc Operating Ambient Temperature (see Thermal Considerations section) Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min 36 Typ Max Unit Operating Input Voltage All VIN 48 75 Vdc Maximum Input Current All IIN,max 1.7 2.0 Adc All IIN,No load 55 All IIN,stand-by 5 Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1μH source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All Input Ripple Rejection (120Hz) All (VIN= VIN, min to VIN, max, IO=IO, max) Input No Load Current mA (VIN = VIN, nom, IO = 0, module enabled) Input Stand-by Current 7 mA 0.1 A2s (VIN = VIN, nom, module disabled) EMC, EN55022 30 50 60 mAp-p 100 dB See EMC Considerations section CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to an integrated part of sophisticated power architectures. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a time-delay fuse with a maximum rating of 5 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. October 5, 2015 ©2012 General Electric Company. All rights reserved. Page 2 GE Data Sheet KW010/015/020/025 Series Power Modules 36 – 75Vdc Input; 1.2 to 5.0Vdc Output; 10 to 25A Output current Electrical Specifications (continued) Parameter Output Voltage Set-point (VIN=VIN, min, IO=IO, max, TA=25°C) Output Voltage Device Symbol Min Typ Max Unit A VO, set 4.93 5.0 5.08 Vdc F VO, set 3.25 3.3 3.35 Vdc G VO, set 2.46 2.5 2.54 Vdc Y VO, set 1.77 1.8 1.83 Vdc M VO, set 1.48 1.5 1.53 Vdc 1.2 P VO, set 1.18 1.22 Vdc All VO -3.0 +3.0 % VO, set All VO,adj -20.0 +10.0 % VO, set 0.1 % VO, set (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation Line (VIN=VIN, min to VIN, max)  A, F, G  Y, M, P 2 mV % VO, set   0.1 2 mV All   1.0 % VO, set RMS (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) A, F, G, Y   25 75   mVrms mVpk-pk RMS (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) M, P   33 100   mVrms mVpk-pk Load (IO=IO, min to IO, max) A, F, G Y, M, P Temperature (Tref=TA, min to TA, max) Output Ripple and Noise on nominal output (VIN=VIN, nom ,IO= IO, max , TA=TA, min to TA, max) External Capacitance All CO, max 0  10,000 μF Rated Output Current A IO, Rated 0  10 Adc Output Current Limit Inception (Hiccup Mode ) (VO= 90% of VO, set) Output Short-Circuit Current (VO≤250mV) ( Hiccup Mode ) October 5, 2015 F IO, Rated 0  15 Adc G IO, Rated 0  20 Adc Y IO, Rated 0  25 Adc M IO, Rated 0  25 Adc P IO, Rated 0  25 Adc All IO, lim 106 120 146 %IO, Rated All IO, s/c  3  Arms ©2012 General Electric Company. All rights reserved. Page 3 GE Data Sheet KW010/015/020/025 Series Power Modules 36 – 75Vdc Input; 1.2 to 5.0Vdc Output; 10 to 25A Output current Electrical Specifications (continued) Parameter Device Symbol A η 92.0 VIN= VIN, nom, TA=25°C F η 91.0 % IO=IO, max , VO= VO,set G η 89.0 % Efficiency Min Typ Max Unit % Y η 87.0 % M η 85.0 % P η 84.0 % All fsw 190 Peak Deviation All Vpk Settling Time (Vo