QHHD019A0B41Z

GE Data Sheet QHHD019A0B Hammerhead* Series; DC-DC Converter Power Modules 18Vdc –75Vdc input; 12Vdc output; 19A Output Current Features  Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863.(-Z versions)  Compliant to REACH Directive (EC) No 1907/2006  Small Size and low profile, follows industry standard DOSA 1/4th Brick footprint 58.4 mm x 36.8 mm x 10.2 mm (2.30 in x 1.45 in x 0.40 in)  Ultra-wide Input Voltage Range, 18Vdc to 75Vdc  No minimum load  High efficiency – 93.5% at full load  Constant switching frequency Hybrid power architectures  Low output ripple and noise  Wireless Networks   Enterprise Networks including Power over Ethernet (PoE) Paste-in-hole reflow compliant for all versions, TH pins and heat plates  Negative Remote On/Off logic  Industrial Equipment  Output overcurrent/voltage protection (hiccup)  Over-temperature protection  Output Voltage adjust: 90% to 110% of Vo,nom  Suitable for cold wall cooling using heatplate version of the module  ANSI/UL* 62368-1 and CAN/CSA† C22.2 No. 62368-1 Recognized, DIN VDE‡ 0868-1/A11:2017 (EN623681:2014/A11:2017)  CE mark meets 2014/35/EU directive§  Meets the voltage and current requirements for ETSI 300132-2 and complies with and licensed for Basic insulation rating  2250 Vdc Isolation tested in compliance with IEEE 802.3¤ PoE standards  ISO**9001 and ISO 14001 certified manufacturing facilities RoHS Compliant Applications  Options  1/4th Brick heat plate with threaded inserts Description The QHHD019A0B [HAMMERHEAD*] Series, quarter-brick, low-height power modules are isolated dc-dc converters which provide a single, precisely regulated output voltage over an ultra-wide input voltage range of 18-75Vdc. The QHHD019A0B provides 12Vdc nominal output voltage rated for 19Adc output current. The module incorporates GE’s vast heritage for reliability and quality, while also using the latest in technology, and component and process standardization to achieve highly competitive cost. The open frame module construction, enable designers to develop cost and space efficient solutions. The module achieves typical full load efficiency greater than 93% at VIN=24Vdc and VIN=48Vdc. Standard features include remote On/Off, remote sense, output voltage adjustment, overvoltage, overcurrent and over temperature protection. An optional heat plate allows for external standard, quarter-brick heat sink attachment to achieve higher output current in high temperature applications. * Trademark of General Electric Company. # UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. § This product is intended for integration into end-user equipment . All of the required procedures of end-use equipment should be followed. ¤ IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Incorporated. ** ISO is a registered trademark of the International Organization of Standards † ‡ April 29, 2021 ©2016 General Electric Company. All rights reserved. Page 1 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Revision History Last update: Updated Top View Dimension on Page 15 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the technical requirement. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit All VIN -0.3 80 Vdc All VIN, trans -0.3 100 Vdc All TA -40 85 °C Storage Temperature All Tstg -55 Operating altitude (see section on thermal considerations) All I/O Isolation Voltage (100% factory Hi-Pot tested) All Input Voltage (Continuous) Transient (100ms) Operating Ambient Temperature (see Thermal Considerations section)   125 °C 5000 m 2250 Vdc Electrical Specifications Unless otherwise indicated, specifications apply at VIN = 48Vdc, resistive load, and TA=25C conditions with airflow=300LFM apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit All VIN 18 24/48 75 Vdc VIN = 24Vdc, (IO = 0, module enabled) All IIN,No load 180 mA VIN = 48Vdc, (IO = 0, module enabled) All IIN,No load 120 mA All IIN,stand-by 8 mA Operating Input Voltage Input No Load Current Input Stand-by Current (VIN = 24 to 48Vdc, module disabled) Maximum Input Current (VIN=18Vdc, IO=IO, max) Adc 12.0 VO 14 Inrush Transient All Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12μH source impedance; VIN=0V to 75Vdc, IO= IOmax ; see Test configuration section) All 30 mAp-p Input Ripple Rejection (120Hz) All 60 dB EMC, EN55032 I 2t 0.1 A 2s See EMC Considerations section CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 25A (voltage rating 125Vac) in the ungrounded input lead. (Littelfuse Part #0456025, Surface Mount 456 Series - Nano 2® or equivalent, see Safety Considerations section) April 29, 2021 ©2016 General Electric Company. All rights reserved. Page 2 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Electrical Specifications (continued) Parameter Device Symbol Min Typ Max Unit Output Voltage Set-point (VIN=24 to 48Vdc, IO=IO, max, TA=25°C) Output Voltage 12 VO VO, set 11.82 12.00 12.18 Vdc Vdc All VO -3.0  +3.0 % VO, set 12 Vo VO, adj -10 +10* % VO, set (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range (*Vin>20V) Selected by external resistor Output Regulation Line (VIN=VIN, min to VIN, max) Load (IO=IO, min to IO, max) Temperature (Tref=TA, min to TA, max) Output Ripple and Noise on nominal output Measured with 10uF Tantalum||1uF ceramic (VIN=24 to 48Vdc, IO=80%IO, max, TA=25°C) RMS (5Hz to 20MHz bandwidth) Peak-to-Peak (5Hz to 20MHz bandwidth) External Capacitance All All All    0.05 0.05 1.0 0.2 0.2 1.5 % VO, set % VO, set % VO, set 12 VO     75 160 mVrms mVpk-pk 12 VO CO, max 0  5000 μF 12 VO Io 0  19.0 Adc 12 VO IO, lim 23  Adc All IO, s/c 12.0VO η 93.5  % 12.0VO η 93  % All fsw  250  kHz Peak Deviation All Vpk  3.0  % VO, set Settling Time (Vo1500V ceramics. Figure 25. Suggested Configuration for EN55032 Class B. VIN = 48V, Io = Io,max, L Line April 29, 2021 VIN = 48V, Io = Io,max, N Line ©2016 General Electric Company. All rights reserved. Page 13 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Mechanical Outline for Through-Hole Module (Open Frame) Dimensions are in millimeters and [inches]. Tolerances: x.x mm  0.5 mm [x.xx in.  0.02 in.] (Unless otherwise indicated) x.xx mm  0.25 mm [x.xxx in  0.010 in.] April 29, 2021 ©2016 General Electric Company. All rights reserved. Page 14 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Mechanical Outline for Through Hole Module with heat plate (-H, Option) Dimensions are in millimeters and (inches). Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [Unless otherwise indicated] x.xx mm  0.25 mm (x.xxx in  0.010 in.) April 29, 2021 ©2016 General Electric Company. All rights reserved. Page 15 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Recommended Pad Layout for Through Hole Module Dimensions are in millimeters and (inches). Tolerances: x.x mm  0.5 mm (x.xx in.  0.02 in.) [Unless otherwise indicated] x.xx mm  0.25 mm (x.xxx in  0.010 in.) Hole and Pad diameter recommendations Pin Number Hole Dia (mm) Pad Dia (mm) 1-3, 5-7 1.6 2.1 4, 8 2.2 3.2 April 29, 2021 ©2016 General Electric Company. All rights reserved. Page 16 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Packaging Details Min order quantity The open frame versions of the QHHD019A0B are supplied as standard in the plastic trays shown in Figure 26. Each tray contains a total of 12 power modules. The trays are self-stacking and each shipping box the QHHD019A0B through hole module will contain 2 full trays plus one empty hold down tray giving a total number of 24 power Tray Specification Material Max surface resistivity Color Capacity PET (1mm) 109-1011/sq Clear 12 power modules 24 pcs (1 box of 2 full trays + 1 empty top tray) Figure 26. Open Frame Through Hole Packaging Tray April 29, 2021 ©2016 General Electric Company. All rights reserved. Page 17 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Packaging Details The Heat Plate versions of the QHHD019A0B (suffix –H) are supplied as standard in the plastic trays shown in Figure 27. Tray Specification Material PET(1mm) Max surface resistivity 109-1011/sq Color Clear Capacity 12 power modules Each tray contains a total of 12 power modules. The trays are self-stacking and each shipping box the QHHD019A0B (suffix –H) through hole module will contain 2 full trays plus one empty hold down tray giving a total number of 24 power Min order quantity 24 pcs (1 box of 2 full trays + 1 empty top tray) Figure 27. Heat Plate version Packaging Tray April 29, 2021 ©2016 General Electric Company. All rights reserved. Page 18 GE Data Sheet QHHD019A0B Series: DC-DC Converter Power Module 18 to 75Vdc Input; 12Vdc, 19A, 225W Output Ordering Information Please contact your GE Energy Sales Representative for pricing, availability and optional features. Table 1. Device Codes QHHD019A0B41Z 24V/48V (18-75Vdc) Output Current 19.0A QHHD019A0B41-HZ 24V/48V (18-75Vdc) 19.0A 12.0V Negative Through hole 150030812 QHHD019A0B641-HZ 24V/48V (18-75Vdc) 19.0A 12.0V Negative Through hole 150037357 Product codes Input Voltage Output Voltage 12.0V Remote On/Off Logic Negative Connector Type Through hole 150029667 Comcodes Ratings Table 2. Device Options Characteristic Form Factor Family Designator Input Voltage Output Current Output Voltage Pin Length Action following Protective Shutdown Options On/ Off Logic Customer Specific Mechanical Features RoHS Character and Position Q HH D 019A0 B Definition Q = 1 / 4th Brick HH = Hammerhead™ Series D = UltraWide Range, 18V-75V 019A0 = 019.0 Amps Maximum Output Current B=12V Nominal Omit = Default Pin Length shown in Mechanical Outline Figures 6 = Pin Length: 3.68 mm ± 0.25mm , (0.145 in. ± 0.010 in.) 8 = Pin Length: 2.79 mm ± 0.25mm , (0.110 in. ± 0.010 in.) 6 8 4 = Auto-restart following shutdown (Overcurrent/ Overvoltage) Must be ordered 4 Omit = Positive Logic 1 = Negative Logic 1 XY XY= Customer Specific Modified Code, Omit for Standard Code Omit = Standard open Frame Module H = 1/ 4th Brick size heat plate, for use with heat sinks (not available H with -S option) 18H 18H = 1/ 4th Brick size heat plate with unthreaded inserts for use in coldwall applications (not available with -S option) S S = Surface Mount connections Omit = RoHS 5/ 6, Lead Based Solder Used Z Z = RoHS 6/ 6 Compliant, Lead free Contact Us For more information, call us at USA/Canada: +1 877 546 3243, or +1 972 244 9288 Asia-Pacific: +86-21-53899666 Europe, Middle-East and Africa: +49.89.878067-280 Go.ABB/Industrial GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. April 29, 2021 ©2016 General Electric Company. All International rights reserved. Version 1_6