SHHD005A0F41Z

GE Data Sheet SHHD005A0F Hammerhead* Series; DC-DC Converter Power Modules 18-75Vdc Input; 3.3Vdc, 5A, 15W Output Features RoHS Compliant • Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 (-Z versions) • Compliant to REACH Directive (EC) No 1907/2006 • Complaint to IPC 9592A, Category 2, Class II • Ultra-wide Input Voltage Range, 18Vdc to 75Vdc • No minimum load • High efficiency – 87.5% at full load (Vin=24 or 48Vdc) • Constant switching frequency • Low output ripple and noise • Small Size and low profile, follows industry standard 1x1 footprint 27.9mm x 24.4mm x 8.5mm (MAX) Applications (1.10 x 0.96 x 0.335 in) • Wireless Networks • Hybrid power architectures • Optical and Access Network Equipment • Enterprise Networks including Power over Ethernet (PoE) • Industrial markets Options • Negative Remote On/Off logic • Surface Mount/Tape and Reel (-SR Suffix) • Short pin versions • Surface mount (SMT) or Through hole (TH) • Reflow process compliant, both SMT and TH versions • Positive Remote On/Off logic • Output overcurrent/voltage protection (hiccup) • Over-temperature protection • Output Voltage adjust: 90% to 110% of Vo,nom • Wide operating temperature range (-40°C to 85°C) • ANSI/UL* 62368-1 and CAN/CSA† C22.2 No. 62368-1 Recognized, DIN VDE‡ 0868-1/A11:2017 (EN623681:2014/A11:2017) • CE mark meets 2006/95/EC directive§ • Meets the voltage and current requirements for ETSI 300-1322 and complies with and licensed for Basic insulation • 2250 Vdc Isolation tested in compliance with IEEE 802.3¤ PoE standards • ISO** 9001 and ISO 14001 certified manufacturing facilities Description The SHHD005A0F Hammerhead series power modules are isolated dc-dc converters that operate over an ultra-wide input voltage range of 18 Vdc -75Vdc and provide a single precisely regulated output voltage at 3.3Vdc. This series is a low cost, smaller size alternative to the existing LW/LAW/LC/SC/SW with enhanced performance parameters. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency of 87.5% typical at full load. Built-in filtering for both input and output minimizes the need for external filtering. The module is fully self-protected with output over-current and over-voltage, over-temperature and input under voltage shutdown control. Optional features include negative or positive on/off logic and SMT connections. * Trademark of General Electric Company # UL is a registered trademark of Underwriters Laboratories, Inc. † CSA is a registered trademark of Canadian Standards Association. ‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V. § This product is intended for integration into end-user equipment. All of the required procedures of end-use equipment should be followed. ¤ IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Incorporated. ** ISO is a registered trademark of the International Organization of Standards. April 16, 2021 ©2012 General Electric Company. All rights reserved. Page 1 Data Sheet GE SHHD005A0F Hammerhead Series; DC-DC Converter Power Modules 18-75Vdc Input; 3.3Vdc, 5A, 15W Output Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min All VIN All VIN, trans All Storage Temperature All Altitude* All Input Voltage (Continuous) Transient (100ms) Operating Ambient Temperature Max Unit -0.3 80 Vdc -0.3 100 Vdc TA -40 85 °C Tstg -55 (see Thermal Considerations section) I/O Isolation Voltage (100% factory Hi-Pot tested) 125 °C 4000 m All w/o-55 Viso ⎯ 2250 Vdc -55 option Viso ⎯ 1500 Vdc * For higher altitude applications, contact your GE Sales Representative for alternative conditions of use. Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit All VIN 18 24/48 75 Vdc VIN = 24Vdc, (IO = 0, module enabled) All IIN,No load 40 mA VIN = 48Vdc, (IO = 0, module enabled) All IIN,No load 30 mA All IIN,stand-by 4 Maximum Input Current (VIN=18Vdc, IO=IO, max) All IIN,max 1.1 Adc Inrush Transient All I2t 0.05 A2s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12μH source impedance; VIN=0V to 75Vdc, IO= IOmax ; see Test configuration section) All Input Ripple Rejection (120Hz) All Operating Input Voltage Input No Load Current Input Stand-by Current (VIN = 24 to 48Vdc, module disabled) EMC, EN55032 6 mA 30 mAp-p 60 dB See EMC Considerations section CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 3 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information. April 16, 2021 ©2012 General Electric Company. All rights reserved. Page 2 Data Sheet GE SHHD005A0F Hammerhead Series; DC-DC Converter Power Modules 18-75Vdc Input; 3.3Vdc, 5A, 15W Output Electrical Specifications (continued) Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Output Voltage Set-point (VIN=24 to 48Vdc, IO=IO, max, TA=25°C) Device Symbol Min Typ Max Unit 3.3 VO VO, set 3.25 3.30 3.35 Vdc All VO -3.0 ⎯ +3.0 % VO, set All VO, adj -10 +10 % VO, set Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by external resistor Output Regulation Line (VIN=VIN, min to VIN, max) All ⎯ 0.05 0.2 % VO, set Load (IO=IO, min to IO, max) All ⎯ 0.05 0.2 % VO, set Temperature (Tref=TA, min to TA, max) All ⎯ ⎯ 1.0 % VO, set ⎯ ⎯ 25 mVrms ⎯ ⎯ 75 mVpk-pk Output Ripple and Noise on nominal output Measured with 10uF Tantalum||1uF ceramic (VIN=24 to 48Vdc, IO=80%IO, max, TA=25°C) RMS (5Hz to 20MHz bandwidth) All Peak-to-Peak (5Hz to 20MHz bandwidth) External Capacitance All CO, max 0 ⎯ 1000 μF Output Current All Io 0 ⎯ 5.0 Adc Output Current Limit Inception (Hiccup Mode) All IO, lim 5.5 7.0 ⎯ Adc All IO, s/c ⎯ ⎯ 0.8 Arms All η 86.0 87.5 ⎯ % All fsw ⎯ 350 ⎯ kHz Peak Deviation All Vpk ⎯ 3.0 ⎯ % VO, set Settling Time (Vo100μF OUTPUT VOLTAGE VO (V) (1V/div) OUTPUT VOLTAGE VO (V) (1V/div) INPUT VOLTAGE VIN (V) (20V/div) On/Off VOLTAGE VOn/Off (V) (2V/div) Figure 3. Typical output ripple and noise (Io = Io,max). TIME, t (5ms/div) Figure 5.Typical Start-up Using Remote On/Off, negative logic version shown (VIN = 24V or 48V, Io = Io,max). April 16, 2021 TIME, t (5ms/div) Figure 6. Typical Start-up Using Input Voltage (VIN = 48V, Io = Io,max). ©2012 General Electric Company. All rights reserved. Page 5 Data Sheet GE SHHD005A0F Hammerhead Series; DC-DC Converter Power Modules 18-75Vdc Input; 3.3Vdc, 5A, 15W Output Test Configurations Design Considerations CURRENT PROBE TO OSCILLOSCOPE Vin+ BATTERY 12μH CS 220μF Input Source Impedance The power module should be connected to a low ac-impedance source. Highly inductive source impedance can affect the stability of the power module. For the test configuration in Figure 7, a 33μF electrolytic capacitor (ESR