GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Features
RoHS Compliant
Compliant to RoHS II EU “Directive 2011/65/EU”
Compliant to REACH Directive (EC) No 1907/2006
Compliant to IPC-9592 (September 2008), Category 2,
Class II
Ultra low height design for very dense power
applications.
High technology encapsulation for improved thermal
performance, electrical insulation, and easy
manufacturing.
Small size: 20.32 mm x 11.43 mm x 3 mm (Max)
(0.8 in x 0.45 in x 0.118 in)
Output voltage programmable from 0.6Vdc to 5.5Vdc
via external resistor. Digitally adjustable down to
0.45Vdc
Applications
Distributed power architectures
Wide Input voltage range (3Vdc-14.4Vdc)
Intermediate bus voltage applications
Telecommunications equipment
Wide operating temperature range [-40°C to 105°C]. See
derating curves
Servers and storage applications
DOSA approved footprint
Digital interface through the PMBusTM # protocol
Networking equipment
Industrial equipment
Tunable LoopTM to optimize dynamic output voltage
response
Flexible output voltage sequencing EZ-SEQUENCE
Power Good signal
Remote On/Off
Fixed switching frequency with capability of external
synchronization
Output overcurrent protection (non-latching)
Overtemperature protection
Ability to sink and source current
Compatible in a Pb-free or SnPb reflow environment
UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03
Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed
ISO** 9001 and ISO 14001 certified manufacturing
facilities
Vin+
VIN
PGOOD
Vout+
VOUT
VS+
RTUNE
MODULE
SEQ
Cin
ON/OFF
GND
CTUNE
CLK
TRIM
DATA
ADDR0
SMBALRT#
ADDR1
Co
RTrim
RADDR1
RADDR0
SIG_GND
SYNC GND VS-
Description
The 12A Digital SlimLynxTM power modules are non-isolated dc-dc converters that can deliver up to 12A of output current. These
modules operate over a wide range of input voltage (VIN = 3Vdc-14.4Vdc) and provide a precisely regulated output voltage from
0.45Vdc to 5.5Vdc, programmable via an external resistor and PMBus control. Features include a digital interface using the PMBus
protocol, remote On/Off, adjustable output voltage, over current and over temperature protection. The PMBus interface supports a
range of commands to both control and monitor the module. The module also includes the Tunable LoopTM feature that allows the
user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to
savings on cost and PWB area.
* UL is a registered trademark of Underwriters Laboratories, Inc.
†
CSA is a registered trademark of Canadian Standards Association.
VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
‡
#
The PMBus name and logo are registered trademarks of the System Management Interface Forum (SMIF)
June 15, 2016
©2016 General Electric Company. All rights reserved.
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings
only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations
sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability.
Parameter
Device
Symbol
Min
Max
Unit
All
VIN
-0.3
15
V
7
V
Input Voltage
Continuous
SEQ, SYNC, VS+
All
CLK, DATA, SMBALERT#
All
3.6
V
Operating Ambient Temperature
All
TA
-40
85
°C
All
Tstg
-55
125
°C
(see Thermal Considerations section)
Storage Temperature
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
Parameter
Device
Symbol
Min
Typ
Max
Unit
Operating Input Voltage
All
VIN
3
14.4
Vdc
Maximum Input Current
All
IIN,max
10A
Adc
VO,set = 0.6 Vdc
IIN,No load
50
mA
VO,set = 5Vdc
IIN,No load
220
mA
Input Stand-by Current
(VIN = 12Vdc, module disabled)
All
IIN,stand-by
20
mA
Inrush Transient
All
I2t
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 1μH source impedance; VIN =0 to
14V, IO= IOmax ; See Test Configurations)
All
50
mAp-p
Input Ripple Rejection (120Hz)
All
-55
dB
(VIN=3V to 14V, IO=IO, max )
Input No Load Current
(VIN = 12Vdc, IO = 0, module enabled)
June 15, 2016
©2016 General Electric Company. All rights reserved.
1
A2s
Page 2
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Electrical Specifications (continued)
Parameter
Device
Symbol
Min
Output Voltage Set-point (with 0.1% tolerance for external
resistor used to set output voltage)
All
VO, set
-1.0
Output Voltage (Over all operating input voltage, resistive
load, and temperature conditions until end of life)
All
VO, set
-3.0
Adjustment Range (selected by an external resistor)
(Some output voltages may not be possible depending on the
input voltage – see Feature Descriptions Section)
All
VO
0.6
PMBus Adjustable Output Voltage Range
All
VO,adj
-25
PMBus Output Voltage Adjustment Step Size
All
Remote Sense Range
All
Typ
0
Max
Unit
+1.0
% VO, set
+3.0
% VO, set
5.5
Vdc
+25
%VO,set
0.4
%VO,set
0.5
Vdc
Output Regulation (for VO ≥ 2.5Vdc)
Line (VIN=VIN, min to VIN, max)
All
+0.4
% VO, set
Load (IO=IO, min to IO, max)
All
10
mV
Output Regulation (for VO < 2.5Vdc)
Line (VIN=VIN, min to VIN, max)
All
5
mV
Load (IO=IO, min to IO, max)
All
10
mV
Temperature (Tref=TA, min to TA, max)
All
0.4
% VO, set
50
100
mVpk-pk
20
38
mVrms
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max Co = 3x47nF // 2x47 μF
ceramic capacitors)
Peak-to-Peak (5Hz to 20MHz bandwidth)
RMS (5Hz to 20MHz bandwidth)
External Capacitance
All
All
1
Without the Tunable LoopTM
ESR ≥ 1 mΩ
All
CO, max
2x47
2x47
μF
ESR ≥ 0.15 mΩ
All
CO, max
2x47
1000
μF
ESR ≥ 10 mΩ
10000
μF
12
Adc
With the Tunable Loop
TM
All
CO, max
2x47
Output Current (in either sink or source mode)
All
Io
0
Output Current Limit Inception (Hiccup Mode)
(current limit does not operate in sink mode)
All
IO, lim
130
% Io,max
Output Short-Circuit Current
All
IO, s/c
1.5
Arms
VO,set = 0.6Vdc
η
72
%
VIN= 12Vdc, TA=25°C
VO, set = 1.2Vdc
η
81
%
IO=IO, max , VO= VO,set
VO,set = 1.8Vdc
η
85
%
VO,set = 2.5Vdc
η
87.5
%
VO,set = 3.3Vdc
η
89
%
VO,set = 5.0Vdc
η
92
%
All
fsw
(VO≤250mV) ( Hiccup Mode )
Efficiency
Switching Frequency
800
kHz
1 External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best
transient response. See the Tunable LoopTM section for details.
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 3
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Electrical Specifications (continued)
Parameter
Device
Frequency Synchronization
Symbol
Min
Typ
Max
Unit
760
800
840
kHz
All
Synchronization Frequency Range
All
High-Level Input Voltage
All
Low-Level Input Voltage
All
VIL
0.4
V
Input Current, SYNC
All
ISYNC
100
nA
Minimum Pulse Width, SYNC
All
tSYNC
100
ns
Maximum SYNC rise time
All
tSYNC_SH
100
ns
VIH
2
V
General Specifications
Parameter
Device
Calculated MTBF (IO=0.8IO, max, TA=40°C) Telecordia Issue 2 Method 1
Case 3
Min
All
Weight
Typ
Max
15,233,204
Unit
Hours
1.8 (0.06)
g (oz.)
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See
Feature Descriptions for additional information.
Parameter
Device
Symbol
Input High Current
All
IIH
Input High Voltage
All
VIH
Input Low Current
All
Input Low Voltage
All
Min
Typ
Max
Unit
1
mA
2
VIN,max
V
IIL
1
mA
VIL
-0.2
0.6
V
On/Off Signal Interface
(VIN=VIN, min to VIN, max ; open collector or equivalent,
Signal referenced to GND)
Device code with suffix “4” – Positive Logic (See Ordering
Information)
Logic High (Module ON)
Logic Low (Module OFF)
Device Code with no suffix – Negative Logic (See Ordering
Information)
(On/OFF pin is open collector/drain logic input with
external pull-up resistor; signal referenced to GND)
Logic High (Module OFF)
Input High Current
All
IIH
―
―
1
mA
Input High Voltage
All
VIH
2
―
VIN, max
Vdc
Input low Current
All
IIL
―
―
50
μA
Input Low Voltage
All
VIL
-0.2
―
0.6
Vdc
Logic Low (Module ON)
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 4
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Feature Specifications (cont.)
Parameter
Device
Symbol
Min
Typ
Max
Units
Case 1: On/Off input is enabled and then input power is
applied (delay from instant at which VIN = VIN, min until Vo =
10% of Vo, set)
All
Tdelay
―
0.9
―
msec
Case 2: Input power is applied for at least one second and
then the On/Off input is enabled (delay from instant at
which Von/Off is enabled until Vo = 10% of Vo, set)
All
Tdelay
―
0.8
―
msec
Output voltage Rise time (time for Vo to rise from
10% of Vo, set to 90% of Vo, set)
All
Trise
―
2
―
msec
Turn-On Delay and Rise Times
(VIN=VIN, nom, IO=IO, max , VO to within ±1% of steady state)
Output voltage overshoot (TA = 25oC
VIN= VIN, min to VIN, max,IO = IO, min to IO, max)
With or without maximum external capacitance
3
% VO,
set
Over Temperature Protection
(See Thermal Considerations section)
All
Tref
130
°C
PMBus Over Temperature Warning Threshold *
All
TWARN
120
°C
Tracking Accuracy
(Power-Up: 2V/ms)
All
VSEQ –Vo
100
mV
(Power-Down: 2V/ms)
All
VSEQ –Vo
100
mV
(VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo)
Input Undervoltage Lockout
Turn-on Threshold
All
2.475
3.025
Vdc
Turn-off Threshold
All
2.25
2.75
Vdc
Hysteresis
All
PMBus Adjustable Input Under Voltage Lockout Thresholds
All
Resolution of Adjustable Input Under Voltage Threshold
All
0.25
2.5
Vdc
14
Vdc
500
mV
PGOOD (Power Good)
Signal Interface Open Drain, Vsupply ≤ 5VDC
Overvoltage threshold for PGOOD ON
All
108
Overvoltage threshold for PGOOD OFF
All
110
Undervoltage threshold for PGOOD ON
All
92
%VO,
set
%VO,
set
%VO,
set
%VO,
Undervoltage threshold for PGOOD OFF
All
90
Pulldown resistance of PGOOD pin
All
50
Ω
Sink current capability into PGOOD pin
All
5
mA
set
* Over temperature Warning – Warning may not activate before alarm and unit may shutdown before warning
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 5
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Digital Interface Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See
Feature Descriptions for additional information.
Parameter
Conditions
Symbol
Min
Typ
Max
Unit
Input High Voltage (CLK, DATA)
VIH
2.1
Input Low Voltage (CLK, DATA)
VIL
Input high level current (CLK, DATA)
IIH
-10
10
μA
Input low level current (CLK, DATA)
IIL
-10
10
μA
0.4
V
10
μA
PMBus Signal Interface Characteristics
Output Low Voltage (CLK, DATA, SMBALERT#)
IOUT=2mA
VOL
Output high level open drain leakage current (DATA,
SMBALERT#)
VOUT=3.6V
IOH
Pin capacitance
0
CO
PMBus Operating frequency range
3.6
V
0.8
V
0.7
pF
Slave Mode
FPMB
10
Receive Mode
Transmit Mode
tHD:DAT
0
300
ns
tSU:DAT
250
ns
Read delay time
tDLY
153
Output current measurement range
IRNG
0
Output current measurement resolution
IRES
62.5
Output current measurement gain accuracy at 25°C
(with IOUT, CORR)
IACC
±5
%
Output current measurement offset
IOFST
0.1
A
Data hold time
Data setup time
400
kHz
Measurement System Characteristics
VOUT measurement range
VOUT(rng)
VOUT measurement resolution
VOUT(res)
VOUT measurement accuracy
VOUT(ACC)
-15
VOUT measurement offset
VOUT(ofst)
VIN measurement range
VIN(rng)
192
231
18
μs
A
mA
0
5.5
15.625
V
mV
15
%
-3
3
%
3
14.4
V
VIN measurement resolution
VIN(res)
VIN measurement accuracy
VIN(ACC)
-15
15
%
VIN measurement offset
VIN(ofst)
-5.5
1.4
LSB
June 15, 2016
32.5
©2016 General Electric Company. All rights reserved.
mV
Page 6
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Characteristic Curves
The following figures provide typical characteristics for the 12A Digital SlimLynxTM at 0.6Vo and 25oC.
85
80
Vin=3.3V
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
75
70
65
Vin=12V
Vin=14.4V
60
55
50
0
2
4
6
8
10
12
OUTPUT CURRENT, IO (A)
OUTPUT VOLTAGE
VO (V) (5mV/div)
IO (A) (10Adiv)
Figure 2. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT CURRENT,
VO (V) (50mV/div)
OUTPUT VOLTAGE
Figure 1. Converter Efficiency versus Output Current.
AMBIENT TEMPERATURE, TA OC
TIME, t (500ns/div)
TIME, t (20µs /div)
INPUT VOLTAGE
VIN (V) (5V/div)
VO (V) (200mV/div)
VON/OFF (V) (5V/div)
VO (V) (200mV/div)
Figure 4. Transient Response to Dynamic Load Change from
50% to 100% at 12Vin, Cout=1x47uF+11x330uF, CTune=47nF,
RTune=180Ω
OUTPUT VOLTAGE
ON/OFF VOLTAGE
OUTPUT VOLTAGE
Figure 3. Typical output ripple and noise (CO=2x47μF
ceramic, VIN = 12V, Io = Io,max, ).
TIME, t (2ms/div)
TIME, t (2ms/div)
Figure 5. Typical Start-up Using On/Off Voltage (Io = Io,max).
June 15, 2016
Figure 6. Typical Start-up Using Input Voltage (VIN = 12V, Io =
Io,max).
©2016 General Electric Company. All rights reserved.
Page 7
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Characteristic Curves
The following figures provide typical characteristics for the 12A Digital SlimLynxTM at 1.2Vo and 25oC.
95
90
EFFICIENCY, η (%)
80
OUTPUT CURRENT, Io (A)
85
Vin=3.3V
75
70
Vin=14.4V
Vin=12V
65
60
55
50
0
2
4
6
8
10
12
OUTPUT CURRENT, IO (A)
OUTPUT VOLTAGE
VO (V) (10mV/div)
IO (A) (10Adiv)
Figure 8. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT CURRENT
VO (V) (50mV/div)
OUTPUT VOLTAGE
Figure 7. Converter Efficiency versus Output Current.
AMBIENT TEMPERATURE, TA OC
TIME, t (500ns/div)
TIME, t (20µs /div)
INPUT VOLTAGE
VIN (V) (5V/div)
VO (V) (500mV/div)
VON/OFF (V) (5V/div)
VO (V) (500mV/div)
OUTPUT VOLTAGE
ON/OFF VOLTAGE
OUTPUT VOLTAGE
Figure 9. Typical output ripple and noise (CO=2x47μF
ceramic, VIN = 12V, Io = Io,max, ).
Figure 10. Transient Response to Dynamic Load Change from
50% to 100% at 12Vin, Cout = 3x47uF+3x330uF, CTune = 12nF
& RTune = 220 ohms
TIME, t (2ms/div)
TIME, t (2ms/div)
Figure 11. Typical Start-up Using On/Off Voltage (Io = Io,max).
June 15, 2016
Figure 12. Typical Start-up Using Input Voltage (VIN = 12V, Io =
Io,max).
©2016 General Electric Company. All rights reserved.
Page 8
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Characteristic Curves
The following figures provide typical characteristics for the 12A Digital SlimLynxTM at 1.8Vo and 25oC.
95
90
Vin=3.3V
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
85
80
Vin=14.4V
75
Vin=12V
70
65
60
0
2
4
6
8
10
12
OUTPUT CURRENT, IO (A)
OUTPUT VOLTAGE
VO (V) (20mV/div)
IO (A) (10Adiv)
Figure 14. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT CURRENT,
VO (V) (50mV/div)
OUTPUT VOLTAGE
Figure 13. Converter Efficiency versus Output Current.
AMBIENT TEMPERATURE, TA OC
TIME, t (500ns/div)
TIME, t (20µs /div)
INPUT VOLTAGE
VIN (V) (5V/div)
VO (V) (500mV/div)
VON/OFF (V) (5V/div)
VO (V) (500mV/div)
Figure 16. Transient Response to Dynamic Load Change from
50% to 100% at 12Vin, Cout = 2x47uF+2x330uF,
CTune=5600pF & RTune=220Ω
OUTPUT VOLTAGE
ON/OFF VOLTAGE
OUTPUT VOLTAGE
Figure 15. Typical output ripple and noise (CO=2x47μF
ceramic, VIN = 12V, Io = Io,max, ).
TIME, t (2ms/div)
TIME, t (2ms/div)
Figure 17. Typical Start-up Using On/Off Voltage (Io = Io,max).
June 15, 2016
Figure 18. Typical Start-up Using Input Voltage (VIN = 12V, Io =
Io,max).
©2016 General Electric Company. All rights reserved.
Page 9
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Characteristic Curves
The following figures provide typical characteristics for the 12A Digital SlimLynxTM at 2.5Vo and 25oC.
95
90
EFFICIENCY, η (%)
80
OUTPUT CURRENT, Io (A)
Vin=4.5V
85
Vin=14V
Vin=12V
75
70
65
60
0
2
4
6
8
10
12
OUTPUT CURRENT, IO (A)
OUTPUT VOLTAGE
VO (V) (20mV/div)
IO (A) (10Adiv)
Figure 20. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT CURRENT,
VO (V) (50mV/div)
OUTPUT VOLTAGE
Figure 19. Converter Efficiency versus Output Current.
AMBIENT TEMPERATURE, TA OC
TIME, t (500ns/div)
TIME, t (20µs /div)
INPUT VOLTAGE
VIN (V) (5V/div)
VO (V) (1V/div)
VON/OFF (V) (5V/div)
VO (V) (1V/div)
Figure 22. Transient Response to Dynamic Load Change from
50% to 100% at 12Vin, Cout = 2x47uF+1x330uF,
CTune=3300pF & RTune=240Ω
OUTPUT VOLTAGE
ON/OFF VOLTAGE
OUTPUT VOLTAGE
Figure 21. Typical output ripple and noise (CO=2x47μF
ceramic, VIN = 12V, Io = Io,max, ).
TIME, t (2ms/div)
TIME, t (2ms/div)
Figure 23. Typical Start-up Using On/Off Voltage (Io = Io,max).
June 15, 2016
Figure 24. Typical Start-up Using Input Voltage (VIN = 12V, Io =
Io,max).
©2016 General Electric Company. All rights reserved.
Page 10
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Characteristic Curves
The following figures provide typical characteristics for the 12A Digital SlimLynxTM at 3.3Vo and 25oC.
100
95
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
90
Vin=4.5V
85
80
Vin=14V
Vin=12V
75
70
65
60
0
2
4
6
8
10
12
OUTPUT CURRENT, IO (A)
OUTPUT VOLTAGE
VO (V) (50mV/div)
IO (A) (10Adiv)
Figure 26. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT CURRENT,
VO (V) (50mV/div)
OUTPUT VOLTAGE
Figure 25. Converter Efficiency versus Output Current.
AMBIENT TEMPERATURE, TA OC
TIME, t (500ns/div)
TIME, t (20µs /div)
INPUT VOLTAGE
VIN (V) (5V/div)
VO (V) (1V/div)
VO (V) (1V/div)
Figure 28 Transient Response to Dynamic Load Change from
50% to 100% at 12Vin, Cout = 2x47uF+1x330uF,
CTune=2700pF & RTune=300Ω
OUTPUT VOLTAGE
ON/OFF VOLTAGE
VON/OFF (V) (5V/div)
OUTPUT VOLTAGE
Figure 27. Typical output ripple and noise (CO=2x47μF
ceramic, VIN = 12V, Io = Io,max, ).
TIME, t (2ms/div)
TIME, t (2ms/div)
Figure 29. Typical Start-up Using On/Off Voltage (Io = Io,max).
June 15, 2016
Figure 30. Typical Start-up Using Input Voltage (VIN = 12V, Io =
Io,max).
©2016 General Electric Company. All rights reserved.
Page 11
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Characteristic Curves
The following figures provide typical characteristics for the 12A Digital SlimLynxTM at 5Vo and 25oC.
100
95
Vin=7V
OUTPUT CURRENT, Io (A)
EFFICIENCY, η (%)
90
85
Vin=14V
80
Vin=12V
75
70
65
60
0
2
4
6
8
10
12
OUTPUT CURRENT, IO (A)
OUTPUT VOLTAGE
VO (V) (50mV/div)
IO (A) (10Adiv)
Figure 32. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT CURRENT,
VO (V) (50mV/div)
OUTPUT VOLTAGE
Figure 31. Converter Efficiency versus Output Current.
AMBIENT TEMPERATURE, TA OC
TIME, t (500ns/div)
TIME, t (20µs /div)
INPUT VOLTAGE
VIN (V) (5V/div)
VO (V) (2V/div)
VON/OFF (V) (5V/div)
VO (V) (2V/div)
Figure 34. Transient Response to Dynamic Load Change from
50% to 100% at 12Vin, Cout = 1x47uF+1x330uF,
CTune=2200pF & RTune=300Ω
OUTPUT VOLTAGE
ON/OFF VOLTAGE
OUTPUT VOLTAGE
Figure 33. Typical output ripple and noise (CO=2x47μF
ceramic, VIN = 12V, Io = Io,max, ).
TIME, t (2ms/div)
TIME, t (2ms/div)
Figure 35. Typical Start-up Using On/Off Voltage (Io = Io,max).
June 15, 2016
Figure 36. Typical Start-up Using Input Voltage (VIN = 12V, Io =
Io,max).
©2016 General Electric Company. All rights reserved.
Page 12
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Design Considerations
40
2x47uF Ext Cap
Input Filtering
4x47uF Ext Cap
Ripple (mVp-p)
6x47uF Ext Cap
The 12A Digital SlimLynxTM module should be connected to
a low ac-impedance source. A highly inductive source can
affect the stability of the module. An input capacitance
must be placed directly adjacent to the input pin of the
module, to minimize input ripple voltage and ensure
module stability.
To minimize input voltage ripple, ceramic capacitors are
recommended at the input of the module. Figure 37 shows
the input ripple voltage for various output voltages at 12A
of load current with 2x22 µF or 3x22 µF ceramic
capacitors and an input of 12V.
30
8x47uF Ext Cap
20
10
0
0.5
450
1
1.5
1x22uF
400
2.5
3
3.5
4
4.5
5
Output Voltage(Volts)
2x22 uF
350
2
Figure 38. Output ripple voltage for various output
voltages with external 2x47 µF, 4x47 µF, 6x47 µF or 8x47
µF ceramic capacitors at the output (12A load). Input
voltage is 12V.
300
250
200
150
Safety Considerations
100
50
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
Figure 37. Input ripple voltage for various output
voltages with 2x22 µF or 3x22 µF ceramic capacitors at
the input (12A load). Input voltage is 12V.
Output Filtering
These modules are designed for low output ripple voltage
and will meet the maximum output ripple specification with
3x0.047 µF ceramic and 2x47 µF ceramic capacitors at the
output of the module. However, additional output filtering
may be required by the system designer for a number of
reasons. First, there may be a need to further reduce the
output ripple and noise of the module. Second, the dynamic
response characteristics may need to be customized to a
particular load step change.
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards, i.e.,
UL 60950-1 2nd, CSA C22.2 No. 60950-1-07, DIN EN 609501:2006 + A11 (VDE0805 Teil 1 + A11):2009-11; EN 609501:2006 + A11:2009-03.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the input
must meet SELV requirements. The power module has
extra-low voltage (ELV) outputs when all inputs are ELV.
The input to these units is to be provided with a fast acting
fuse (e.g. ABC Bussmann) with a maximum rating of 20 A in
the positive input lead.
To reduce the output ripple and improve the dynamic
response to a step load change, additional capacitance at
the output can be used. Low ESR polymer and ceramic
capacitors are recommended to improve the dynamic
response of the module. Figure 38 provides output ripple
information, measured with a scope with its Bandwidth
limited to 20MHz for different external capacitance values at
various Vo and a full load current of 12A. For stable
operation of the module, limit the capacitance to less than
the maximum output capacitance as specified in the
electrical specification table. Optimal performance of the
module can be achieved by using the Tunable LoopTM feature
described later in this data sheet.
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 13
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
3.3V
SlimLynx Module
+VIN
Analog Feature Descriptions
ENABLE
VIN
Rpullup
Remote On/Off
47K
470
20K
100pF
20K
Q6
4.7K
I
The module can be turned ON and OFF either by using the
ON/OFF pin (Analog interface) or through the PMBus interface
(Digital). The module can be configured in a number of ways
through the PMBus interface to react to the two ON/OFF
inputs:
•
Module ON/OFF can be controlled only through
the analog interface (digital interface ON/OFF
commands are ignored)
•
Module ON/OFF can be controlled only through
the PMBus interface (analog interface is ignored)
•
Module ON/OFF can be controlled by either the
analog or digital interface
The default state of the module (as shipped from the factory)
is to be controlled by the analog interface only. If the digital
interface is to be enabled, or the module is to be controlled
only through the digital interface, this change must be made
through the PMBus. These changes can be made and written
to non-volatile memory on the module so that it is
remembered for subsequent use.
ON/OFF
Q3
20K
20K
100K
20K
Q7
+
2K
20K
Q2
Q5
20K
20K
V
ON/OFF
_
GND
Figure 39. Circuit configuration for using positive On/Off
logic.
SlimLynx Module
3.3V
+VIN
ENABLE
Rpullup
470
100pF
I
ON/OFF
47K
20K
Q3
+
Q6
4.7K
100K
Q2
Q5
20K
2K
V
ON/OFF
_
20K
20K
GND
Figure 40. Circuit configuration for using negative On/Off
logic.
Analog On/Off
The 12A Digital SlimLynxTM power modules feature an On/Off
pin for remote On/Off operation. Two On/Off logic options
are available. In the Positive Logic On/Off option, (device
code suffix “4” – see Ordering Information), the module turns
ON during a logic High on the On/Off pin and turns OFF
during a logic Low. With the Negative Logic On/Off option,
(no device code suffix, see Ordering Information), the module
turns OFF during logic High and ON during logic Low. The
On/Off signal should be always referenced to ground. For
either On/Off logic option, leaving the On/Off pin
disconnected will turn the module ON when input voltage is
present.
For positive logic modules, the circuit configuration for using
the On/Off pin is shown in Figure 39. When the external
transistor Q2 is in the OFF state, the internal transistor Q7 is
turned ON, which turn Q3 OFF which keeps Q6 OFF and Q5
OFF. This allows the internal PWM #Enable signal to be
pulled up by the internal 3.3V, thus turning the module ON.
When transistor Q2 is turned ON, the On/Off pin is pulled
low, which turns Q7 OFF which turns Q3, Q6 and Q5 ON and
the internal PWM #Enable signal is pulled low and the
module is OFF. A suggested value for Rpullup is 20kΩ.
Monotonic Start-up and Shutdown
The module has monotonic start-up and shutdown behavior
for any combination of rated input voltage, output current
and operating temperature range.
Startup into Pre-biased Output
The module can start into a prebiased output as long as the
prebias voltage is 0.5V less than the set output voltage.
Analog Output Voltage Programming
The output voltage of the module is programmable to any
voltage from 0.6dc to 5.5Vdc by connecting a resistor
between the Trim and SIG_GND pins of the module. Certain
restrictions apply on the output voltage set point depending
on the input voltage. These are shown in the Output Voltage
vs. Input Voltage Set Point Area plot in Fig. 41. The Upper
Limit curve shows that for output voltages lower than 1V, the
input voltage must be lower than the maximum of 14.4V. The
Lower Limit curve shows that for output voltages higher than
0.6V, the input voltage needs to be larger than the minimum
of 3V.
For negative logic On/Off modules, the circuit configuration
is shown in Fig. 40. The On/Off pin should be pulled high with
an external pull-up resistor (suggested value for the 3V to
14V input range is 20Kohms). When transistor Q2 is in the
OFF state, the On/Off pin is pulled high, transistor Q3 is
turned ON. This turns Q6 ON, followed by Q5 turning ON
which pulls the internal ENABLE low and the module is OFF.
To turn the module ON, Q2 is turned ON pulling the On/Off
pin low, turning transistor Q3 OFF, which keeps Q6 and Q5
OFF resulting in the PWM Enable pin going high.
Digital On/Off
Please see the Digital Feature Descriptions section.
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 14
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 1
Input Voltage (v)
16
14
VO, set (V)
Rtrim (KΩ)
12
0.6
0.9
1.0
1.2
1.5
1.8
2.5
3.3
5.0
Open
40
30
20
13.33
10
6.316
4.444
2.727
Upper
10
8
6
4
Lower
2
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
Output Voltage (V)
Figure 41. Output Voltage vs. Input Voltage Set Point Area
plot showing limits where the output voltage can be set for
different input voltages.
Digital Output Voltage Adjustment
Please see the Digital Feature Descriptions section.
Remote Sense
VIN(+)
VO(+)
VS+
ON/OFF
LOAD
TRIM
Rtrim
SIG_GND
VS─
Caution – Do not connect SIG_GND to GND elsewhere in the
layout
Figure 42. Circuit configuration for programming output
voltage using an external resistor.
Without an external resistor between Trim and SIG_GND pins,
the output of the module will be 0.6Vdc.To calculate the
value of the trim resistor, Rtrim for a desired output voltage,
should be as per the following equation:
The power module has a Remote Sense feature to minimize
the effects of distribution losses by regulating the voltage
between the sense pins (VS+ and VS-). The voltage drop
between the sense pins and the VOUT and GND pins of the
module should not exceed 0.5V.
Analog Voltage Margining
Output voltage margining can be implemented in the
module by connecting a resistor, Rmargin-up, from the Trim pin
to the ground pin for margining-up the output voltage and
by connecting a resistor, Rmargin-down, from the Trim pin to
output pin for margining-down. Figure 43 shows the circuit
configuration for output voltage margining. The POL
Programming Tool, available at www.gecriticalpower.com
under the Downloads section, also calculates the values of
Rmargin-up and Rmargin-down for a specific output voltage and %
margin. Please consult your local GE Critical Power
technical representative for additional details.
Vo
Rmargin-down
MODULE
12
Rtrim =
kΩ
(Vo − 0.6 )
Q2
Trim
Rmargin-up
Rtrim is the external resistor in kΩ
Rtrim
Vo is the desired output voltage.
Table 1 provides Rtrim values required for some common
output voltages.
Q1
SIG_GND
Figure 43. Circuit Configuration for margining Output
voltage.
Digital Output Voltage Margining
Please see the Digital Feature Descriptions section.
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 15
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Output Voltage Sequencing
The power module includes a sequencing feature, EZSEQUENCE that enables users to implement various types of
output voltage sequencing in their applications. This is
accomplished via an additional sequencing pin. When not
using the sequencing feature, leave it unconnected.
and warnings. To avoid the module shutting down due to the
Output Undervoltage Fault, the module must be set to
continue operation without interruption as the response to
this fault (see the description of the PMBus command
VOUT_UV_FAULT_RESPONSE for additional information).
Overcurrent Protection
The voltage applied to the SEQ pin should be scaled down by
the same ratio as used to scale the output voltage down to
the reference voltage of the module. This is accomplished by
an external resistive divider connected across the
sequencing voltage before it is fed to the SEQ pin as shown
in Fig. 44. In addition, a small capacitor (suggested value
100pF) should be connected across the lower resistor R1.
To provide protection in a fault (output overload) condition,
the unit is equipped with internal current-limiting circuitry
and can endure current limiting continuously. At the point of
current-limit inception, the unit enters hiccup mode. The unit
operates normally once the output current is brought back
into its specified range.
For all SlimLynx modules, the minimum recommended delay
between the ON/OFF signal and the sequencing signal is
10ms to ensure that the module output is ramped up
according to the sequencing signal. This ensures that the
module soft-start routine is completed before the
sequencing signal is allowed to ramp up.
Please see the Digital Feature Descriptions section.
SlimLynx Module
V
SEQ
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with a thermal shutdown circuit. The unit will shut
down if the overtemperature threshold of 150oC(typ) is
exceeded at the thermal reference point Tref .Once the unit
goes into thermal shutdown it will then wait to cool before
attempting to restart.
Digital Temperature Status via PMBus
Please see the Digital Feature Descriptions section.
20K
Digitally Adjustable Output Over and Under Voltage
Protection
SEQ
Please see the Digital Feature Descriptions section.
R1=Rtrim
100 pF
Digital Adjustable Overcurrent Warning
Input Undervoltage Lockout
SIG_GND
Figure 44. Circuit showing connection of the sequencing
signal to the SEQ pin.
When the scaled down sequencing voltage is applied to the
SEQ pin, the output voltage tracks this voltage until the
output reaches the set-point voltage. The final value of the
sequencing voltage must be set higher than the set-point
voltage of the module. The output voltage follows the
sequencing voltage on a one-to-one basis. By connecting
multiple modules together, multiple modules can track their
output voltages to the voltage applied on the SEQ pin.
At input voltages below the input undervoltage lockout limit,
the module operation is disabled. The module will begin to
operate at an input voltage above the undervoltage lockout
turn-on threshold.
Digitally Adjustable Input Undervoltage Lockout
Please see the Digital Feature Descriptions section.
Digitally Adjustable Power Good Thresholds
Please see the Digital Feature Descriptions section.
The module’s output can track the SEQ pin signal with slopes
of up to 0.5V/msec during power-up or power-down.
To initiate simultaneous shutdown of the modules, the SEQ
pin voltage is lowered in a controlled manner. The output
voltage of the modules tracks the voltages below their setpoint voltages on a one-to-one basis. A valid input voltage
must be maintained until the tracking and output voltages
reach ground potential.
Note that in all digital SlimLynx series of modules, the PMBus
Output Undervoltage Fault will be tripped when sequencing
is employed. This will be detected using the STATUS_WORD
and STATUS_VOUT PMBus commands. In addition, the
SMBALERT# signal will be asserted low as occurs for all faults
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 16
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Synchronization
Tunable LoopTM
The module switching frequency can be synchronized to a
signal with an external frequency within a specified range.
Synchronization can be done by using the external signal
applied to the SYNC pin of the module as shown in Fig. 45,
with the converter being synchronized by the rising edge of
the external signal. The Electrical Specifications table
specifies the requirements of the external SYNC signal. If the
SYNC pin is not used, the module should free run at the
default switching frequency. If synchronization is not being
used, connect the SYNC pin to GND.
MODULE
The module has a feature that optimizes transient response
of the module called Tunable LoopTM.
External capacitors are usually added to the output of the
module for two reasons: to reduce output ripple and noise
(see Figure 38) and to reduce output voltage deviations from
the steady-state value in the presence of dynamic load
current changes. Adding external capacitance however
affects the voltage control loop of the module, typically
causing the loop to slow down with sluggish response.
Larger values of external capacitance could also cause the
module to become unstable.
The Tunable LoopTM allows the user to externally adjust the
voltage control loop to match the filter network connected
to the output of the module. The Tunable LoopTM is
implemented by connecting a series R-C between the VS+
and TRIM pins of the module, as shown in Fig. 46. This R-C
allows the user to externally adjust the voltage loop
feedback compensation of the module.
SYNC
+
─
GND
Figure 45. External source connections to synchronize
switching frequency of the module.
VOUT
VS+
Measuring Output Current, Output Voltage and Input
Voltage
Please see the Digital Feature Descriptions section.
RTune
MODULE
CO
CTune
TRIM
RTrim
SIG_GND
GND
Figure. 46. Circuit diagram showing connection of RTUME
and CTUNE to tune the control loop of the module.
Recommended values of RTUNE and CTUNE for different output
capacitor combinations are given in Table 2. Table 2 shows
the recommended values of RTUNE and CTUNE for different
values of ceramic output capacitors up to 1000uF that
might be needed for an application to meet output ripple
and noise requirements. Selecting RTUNE and CTUNE according
to Table 2 will ensure stable operation of the module.
In applications with tight output voltage limits in the
presence of dynamic current loading, additional output
capacitance will be required. Table 3 lists recommended
values of RTUNE and CTUNE in order to meet 2% output
voltage deviation limits for some common output voltages
in the presence of a 6A to 12A step change (50% of full load),
with an input voltage of 12V.
Please contact your GE Critical Power technical
representative to obtain more details of this feature as well
as for guidelines on how to select the right value of external
R-C to tune the module for best transient performance and
stable operation for other output capacitance values.
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 17
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 2. General recommended values of of RTUNE and
CTUNE for Vin=12V and various external ceramic capacitor
combinations.
Co
2x47µF
4x47µF
6x47µF
10x47µF
10x47µF
RTUNE
430
390
300
240
180
CTUNE
390pF
1500pF
2700pF
3300pF
8200pF
Table 3. Recommended values of RTUNE and CTUNE to obtain
transient deviation of 2% of Vout for a 6A step load with
Vin=12V.
Vo
5V
3.3V
2.5V
1.8V
1.2V
0.6V
RTUNE
1x47uF 1x47uF 2x47µF 1x47µF + 3x47µF + 1x47µF +
+
+ 330µF +330µF
2x330µF 3x330µF 11x330µF
Polymer Polymer 330µF Polymer Polymer Polymer
Polymer
300
300
240
220
220
180
CTUNE
2200pF 2200pF 3300pF 5600pF
Co
∆V
55mV
54mV
47mV
31mV
12nF
47nF
21mV
8mV
Note: The capacitors used in the Tunable Loop tables are
47 μF/4 mΩ ESR ceramic and 330 μF/12 mΩ ESR polymer
capacitors.
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 18
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Digital Feature Descriptions
(1% tolerance resistors are recommended). Note that if either
address resistor value is outside the range specified in Table
4, the module will respond to address 127.
PMBus Interface Capability
Table 4
The 12A Digital SlimLynxTM power modules have a PMBus
interface that supports both communication and control. The
PMBus Power Management Protocol Specification can be
obtained from www.pmbus.org. The modules support a
subset of version 1.1 of the specification (see Table 6 for a list
of the specific commands supported). Most module
parameters can be programmed using PMBus and stored as
defaults for later use.
All communication over the module PMBus interface must
support the Packet Error Checking (PEC) scheme. The PMBus
master must generate the correct PEC byte for all
transactions, and check the PEC byte returned by the
module.
The module also supports the SMBALERT# response protocol
whereby the module can alert the bus master if it wants to
talk. For more information on the SMBus alert response
protocol, see the System Management Bus (SMBus)
specification.
The module has non-volatile memory that is used to store
configuration settings. Not all settings programmed into the
device are automatically saved into this non-volatile
memory, only those specifically identified as capable of being
stored can be saved (see Table 6 for which command
parameters can be saved to non-volatile storage).
Digit
Resistor Value (KΩ)
0
10
1
15.4
2
23.7
3
36.5
4
54.9
5
84.5
6
130
7
200
The user must know which I2C addresses are reserved in a
system for special functions and set the address of the
module to avoid interfering with other system operations.
Both 100kHz and 400kHz bus speeds are supported by the
module. Connection for the PMBus interface should follow
the High Power DC specifications given in section 3.1.3 in the
SMBus specification V2.0 for the 400kHz bus speed or the
Low Power DC specifications in section 3.1.2. The complete
SMBus specification is available from the SMBus web site,
smbus.org.
PMBus Data Format
ADDR1
For commands that set thresholds, voltages or report such
quantities, the module supports the “Linear” data format
among the three data formats supported by PMBus. The
Linear Data Format is a two byte value with an 11-bit, two’s
complement mantissa and a 5-bit, two’s complement
exponent. The format of the two data bytes is shown below:
ADDR0
RADDR0
RADDR1
SIG_GND
Data Byte High
7 6 5 4 3
2 1 0 7 6 5 4 3 2 1 0
Exponent
MSB
Data Byte Low
PMBus Enabled On/Off
Mantissa
MSB
The value is of the number is then given by
Value = Mantissa x 2 Exponent
PMBus Addressing
The power module can be addressed through the PMBus
using a device address. The module has 64 possible
addresses (0 to 63 in decimal) which can be set using
resistors connected from the ADDR0 and ADDR1 pins to
SIG_GND. Note that some of these addresses (0, 1, 2, 3, 4, 5,
6, 7, 8, 9, 10, 11 12, 40, 44, 45, 55 in decimal) are reserved
according to the SMBus specifications and may not be
useable. The address is set in the form of two octal (0 to 7)
digits, with each pin setting one digit. The ADDR1 pin sets the
high order digit and ADDR0 sets the low order digit. The
resistor values suggested for each digit are shown in Table 4
June 15, 2016
Figure 47. Circuit showing connection of resistors used to
set the PMBus address of the module.
The module can also be turned on and off via the PMBus
interface. The OPERATION command is used to actually turn
the module on and off via the PMBus, while the
ON_OFF_CONFIG command configures the combination of
analog ON/OFF pin input and PMBus commands needed to
turn the module on and off. Bit [7] in the OPERATION
command data byte enables the module, with the following
functions:
0
1
:
:
Output is disabled
Output is enabled
This module uses the lower five bits of the ON_OFF_CONFIG
data byte to set various ON/OFF options as follows:
Bit Position
Access
Function
Default Value
4
r/w
PU
1
©2016 General Electric Company. All rights reserved.
3
r/w
CMD
0
2
r/w
CPR
1
1
r/w
POL
1
0
r
CPA
1
Page 19
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
PU: Sets the default to either operate any time input power is
present or for the ON/OFF to be controlled by the analog
ON/OFF input and the PMBus OPERATION command. This bit
is used together with the CP, CMD and ON bits to determine
startup.
Bit Value
0
1
Action
Module powers up any time power is
present regardless of state of the analog
ON/OFF pin
Module does not power up until
commanded by the analog ON/OFF pin and
the OPERATION command as programmed
in bits [2:0] of the ON_OFF_CONFIG register.
CMD: The CMD bit controls how the device responds to the
OPERATION command.
Bit Value
0
1
Action
Module ignores the ON bit in the OPERATION
command
Module responds to the ON bit in the
OPERATION command
CPR: Sets the response of the analog ON/OFF pin. This bit is
used together with the CMD, PU and ON bits to determine
startup.
Bit Value
0
1
Action
Module ignores the analog ON/OFF pin, i.e.
ON/OFF is only controlled through the
PMBUS via the OPERATION command
Module requires the analog ON/OFF pin to
be asserted to start the unit
PMBus Adjustable Soft Start Rise Time
The soft start rise time can be adjusted in the module via
PMBus. When setting this parameter, make sure that the
charging current for output capacitors can be delivered by
the module in addition to any load current to avoid nuisance
tripping of the overcurrent protection circuitry during
startup. The TON_RISE command sets the rise time in ms,
and allows choosing soft start times between 600μs and
9ms, with possible values listed in Table 5. Note that the
exponent is fixed at -4 (decimal) and the upper two bits of
the mantissa are also fixed at 0.
Table 5
Rise Time
Exponent
Mantissa
600μs
11100
00000001010
900μs
11100
00000001110
1.2ms
11100
00000010011
1.8ms
11100
00000011101
2.7ms
11100
00000101011
4.2ms
11100
00001000011
6.0ms
11100
00001100000
9.0ms
11100
00010010000
Output Voltage Adjustment Using the PMBus
The VOUT_SCALE_LOOP parameter is important for a
number of PMBus commands related to output voltage
trimming, margining, over/under voltage protection and the
PGOOD thresholds. The output voltage of the module is set
as the combination of the voltage divider formed by RTrim
and a 20kΩ upper divider resistor inside the module, and the
internal reference voltage of the module. The reference
voltage VREF is nominally set at 600mV, and the output
regulation voltage is then given by
20000 + RTrim
VOUT =
× VREF
RTrim
Hence the module output voltage is dependent on the value
of RTrim which is connected external to the module. The
information on the output voltage divider ratio is conveyed
to the module through the VOUT_SCALE_LOOP parameter
which is calculated as follows:
VOUT _ SCALE _ LOOP =
RTrim
20000 + RTrim
The VOUT_SCALE_LOOP parameter is specified using the
“Linear” format and two bytes. The upper five bits [7:3] of the
high byte are used to set the exponent which is fixed at –9
(decimal). The remaining three bits of the high byte [2:0] and
the eight bits of the lower byte are used for the mantissa.
The default value of the mantissa is 00100000000
corresponding to 256 (decimal), corresponding to a divider
ratio of 0.5. The maximum value of the mantissa is 512
corresponding to a divider ratio of 1. Note that the
resolution of the VOUT_SCALE_LOOP command is 0.2%.
When PMBus commands are used to trim or margin the
output voltage, the value of VREF is what is changed inside
the module, which in turn changes the regulated output
voltage of the module.
The nominal output voltage of the module can be adjusted
with a minimum step size of 0.4% over a ±25% range from
nominal using the VOUT_TRIM command over the PMBus.
The VOUT_TRIM command is used to apply a fixed offset
voltage to the output voltage command value using the
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 20
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
“Linear” mode with the exponent fixed at –10 (decimal). The
value of the offset voltage is given by
VOUT ( offset ) = VOUT _ TRIM × 2 −10
This offset voltage is added to the voltage set through the
divider ratio and nominal VREF to produce the trimmed output
voltage. The valid range in two’s complement for this
command is –4000h to 3FFFh. The high order two bits of
the high byte must both be either 0 or 1. If a value outside of
the +/-25% adjustment range is given with this command,
the module will set it’s output voltage to the nominal value
(as if VOUT_TRIM had been set to 0), assert SMBALRT#, set
the CML bit in STATUS_BYTE and the invalid data bit in
STATUS_CML.
Output Voltage Margining Using the PMBus
The module can also have its output voltage margined via
PMBus commands. The command VOUT_MARGIN_HIGH sets
the margin high voltage, while the command
VOUT_MARGIN_LOW sets the margin low voltage. Both the
VOUT_MARGIN_HIGH and VOUT_MARGIN_LOW commands
use the “Linear” mode with the exponent fixed at –10
(decimal). Two bytes are used for the mantissa with the upper
bit [7] of the high byte fixed at 0. The actual margined output
voltage is a combination of the VOUT_MARGIN_HIGH or
VOUT_MARGIN_LOW and the VOUT_TRIM values as shown
below.
VOUT ( MH ) =
(VOUT _ MARGIN _ HIGH + VOUT _ TRIM ) × 2 −10
VOUT ( ML ) =
(VOUT _ MARGIN _ LOW + VOUT _ TRIM ) × 2 −10
Note that the sum of the margin and trim voltages cannot be
outside the ±25% window around the nominal output
voltage. The data associated with VOUT_MARGIN_HIGH and
VOUT_MARGIN_LOW can be stored to non-volatile memory
using the STORE_DEFAULT_ALL command.
The module is commanded to go to the margined high or low
voltages using the OPERATION command. Bits [5:2] are used
to enable margining as follows:
00XX
0101
0110
1001
1010
:
:
:
:
:
Temperature Status via PMBus
The module can provide information related to temperature
of the module through the STATUS_TEMPERATURE
command. The command returns information about
whether the pre-set over temperature fault threshold and/or
the warning threshold have been exceeded.
PMBus Adjustable Output Over and Under Voltage
Protection
The module has output over and under voltage protection
capability. The PMBus command VOUT_OV_FAULT_LIMIT is
used to set the output over voltage threshold from four
possible values: 108%, 110%, 112% or 115% of the
commanded output voltage. The command
VOUT_UV_FAULT_LIMIT sets the threshold that causes an
output under voltage fault and can also be selected from
four possible values: 92%, 90%, 88% or 85%. The default
values are 112% and 88% of commanded output voltage.
Both commands use two data bytes formatted as two’s
complement binary integers. The “Linear” mode is used with
the exponent fixed to –10 (decimal) and the effective over or
under voltage trip points given by:
VOUT (OV _ REQ ) = (VOUT _ OV _ FAULT _ LIMIT ) × 2 −10
VOUT (UV _ REQ ) = (VOUT _ UV _ FAULT _ LIMIT ) × 2 −10
Values within the supported range for over and
undervoltage detection thresholds will be set to the nearest
fixed percentage. Note that the correct value for
VOUT_SCALE_LOOP must be set in the module for the
correct over or under voltage trip points to be calculated.
In addition to adjustable output voltage protection, the 12A
Digital SlimLynxTM module can also be programmed for the
response to the fault. The VOUT_OV_FAULT RESPONSE and
VOUT_UV_FAULT_RESPONSE commands specify the
response to the fault. Both these commands use a single
data byte with the possible options as shown below.
1.
Margin Off
Margin Low (Ignore Fault)
Margin Low (Act on Fault)
Margin High (Ignore Fault)
Margin High (Act on Fault)
PMBus Adjustable Overcurrent Warning
The module can provide an overcurrent warning via the
PMBus. The threshold for the overcurrent warning can be set
using the parameter IOUT_OC_WARN_LIMIT. This command
uses the “Linear” data format with a two byte data word
where the upper five bits [7:3] of the high byte represent the
exponent and the remaining three bits of the high byte [2:0]
and the eight bits in the low byte represent the mantissa.
The exponent is fixed at –1 (decimal). The upper five bits of
the mantissa are fixed at 0 while the lower six bits are
programmable. Note that the actual value for
IOUT_OC_WARN_LIMIT will vary from module to module due
June 15, 2016
to calibration during production test, The resolution of this
warning limit is 500mA. The value of the
IOUT_OC_WARN_LIMIT can be stored to non-volatile memory
using the STORE_DEFAULT_ALL command.
Continue operation without interruption (Bits [7:6]
= 00, Bits [5:3] = xxx)
2. Continue for four switching cycles and then shut
down if the fault is still present, followed by no
restart or continuous restart (Bits [7:6] = 01, Bits
[5:3] = 000 means no restart, Bits [5:3] = 111
means continuous restart)
3. Immediate shut down followed by no restart or
continuous restart (Bits [7:6] = 10, Bits [5:3] = 000
means no restart, Bits [5:3] = 111 means
continuous restart).
4. Module output is disabled when the fault is present
and the output is enabled when the fault no longer
exists (Bits [7:6] = 11, Bits [5:3] = xxx).
Note that separate response choices are possible for output
over voltage or under voltage faults.
PMBus Adjustable Input Undervoltage Lockout
©2016 General Electric Company. All rights reserved.
Page 21
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
The module allows adjustment of the input under voltage
lockout and hysteresis. The command VIN_ON allows setting
the input voltage turn on threshold, while the VIN_OFF
command sets the input voltage turn off threshold. For the
VIN_ON command, possible values are 2.75V, and 3V to 14V
in 0.5V steps. For the VIN_OFF command, possible values are
2.5V to 14V in 0.5V steps. If other values are entered for
either command, they will be mapped to the closest of the
allowed values.
VIN_ON must be set higher than VIN_OFF. Attempting to
write either VIN_ON lower than VIN_OFF or VIN_OFF higher
than VIN_ON results in the new value being rejected,
SMBALERT being asserted along with the CML bit in
STATUS_BYTE and the invalid data bit in STATUS_CML.
Both the VIN_ON and VIN_OFF commands use the “Linear”
format with two data bytes. The upper five bits represent the
exponent (fixed at -2) and the remaining 11 bits represent
the mantissa. For the mantissa, the four most significant bits
are fixed at 0.
Power Good
The module provides a Power Good (PGOOD) signal that is
implemented with an open-drain output to indicate that the
output voltage is within the regulation limits of the power
module. The PGOOD signal will be de-asserted to a low state
if any condition such as overtemperature, overcurrent or loss
of regulation occurs that would result in the output voltage
going outside the specified thresholds. The PGOOD
thresholds are user selectable via the PMBus (the default
values are as shown in the Feature Specifications Section).
Each threshold is set up symmetrically above and below the
nominal value. The POWER_GOOD_ON command sets the
output voltage level above which PGOOD is asserted (lower
threshold). For example, with a 1.2V nominal output voltage,
the POWER_GOOD_ON threshold can set the lower threshold
to 1.14 or 1.1V. Doing this will automatically set the upper
thresholds to 1.26 or 1.3V.
The POWER_GOOD_OFF command sets the level below
which the PGOOD command is de-asserted. This command
also sets two thresholds symmetrically placed around the
nominal output voltage. Normally, the POWER_GOOD_ON
threshold is set higher than the POWER_GOOD_OFF
threshold.
Both POWER_GOOD_ON and POWER_GOOD_OFF
commands use the “Linear” format with the exponent fixed
at –10 (decimal). The two thresholds are given by
VOUT ( PGOOD _ ON ) = ( POWER _ GOOD _ ON ) × 2 −10
VOUT ( PGOOD _ OFF ) = ( POWER _ GOOD _ OFF ) × 2 −10
Both commands use two data bytes with bit [7] of the high
byte fixed at 0, while the remaining bits are r/w and used to
set the mantissa using two’s complement representation.
Both commands also use the VOUT_SCALE_LOOP parameter
so it must be set correctly. The default value of
POWER_GOOD_ON is set at 1.1035V and that of the
POWER_GOOD_OFF is set at 1.08V. The values associated
with these commands can be stored in non-volatile memory
using the STORE_DEFAULT_ALL command.
June 15, 2016
The PGOOD terminal can be connected through a pullup
resistor (suggested value 100KΩ) to a source of 5VDC or
lower.
Measurement of Output Current, Output Voltage
and Input Voltage
The module is capable of measuring key module
parameters such as output current and voltage and input
voltage and providing this information through the PMBus
interface. Roughly every 200μs, the module makes 16
measurements each of output current, voltage and input
voltage. Average values of of these 16 measurements are
then calculated and placed in the appropriate registers. The
values in the registers can then be read using the PMBus
interface.
Measuring Output Current Using the PMBus
The module measures current by using the inductor winding
resistance as a current sense element. The inductor winding
resistance is then the current gain factor used to scale the
measured voltage into a current reading. This gain factor is
the argument of the IOUT_CAL_GAIN command, and
consists of two bytes in the linear data format. The exponent
uses the upper five bits [7:3] of the high data byte in two-s
complement format and is fixed at –15 (decimal). The
remaining 11 bits in two’s complement binary format
represent the mantissa.
The current measurement accuracy is also improved by
each module being calibrated during manufacture with the
offset in the current reading. The IOUT_CAL_OFFSET
command is used to store and read the current offset. The
argument for this command consists of two bytes
composed of a 5-bit exponent (fixed at -4d) and a 11-bit
mantissa. This command has a resolution of 62.5mA and a
range of -4000mA to +3937.5mA. During manufacture,
each module is calibrated by measuring and storing the
current gain factor and offset into non-volatile storage.
The READ_IOUT command provides module average output
current information. This command only supports positive or
current sourced from the module. If the converter is sinking
current a reading of 0 is provided. The READ_IOUT
command returns two bytes of data in the linear data
format. The exponent uses the upper five bits [7:3] of the
high data byte in two-s complement format and is fixed at –
4 (decimal). The remaining 11 bits in two’s complement
binary format represent the mantissa with the 11th bit fixed
at 0 since only positive numbers are considered valid.
Note that the current reading provided by the module is not
corrected for temperature. The temperature corrected
current reading for module temperature TModule can be
estimated using the following equation
𝑰𝑶𝑶𝑶,𝑪𝑪𝑪𝑪 =
𝑰𝑹𝑹𝑹𝑹_𝑶𝑼𝑼
𝟏 + [(𝑻𝑰𝑰𝑰 − 𝟑𝟑) × 𝟎. 𝟎𝟎𝟎𝟎𝟎]
where IOUT_CORR is the temperature corrected value of the
current measurement, IREAD_OUT is the module current
measurement value, TIND is the temperature of the inductor
©2016 General Electric Company. All rights reserved.
Page 22
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
winding on the module. Since it may be difficult to measure
TIND, it may be approximated by an estimate of the module
temperature.
Measuring Output Voltage Using the PMBus
The module can provide output voltage information using
the READ_VOUT command. The command returns two bytes
of data all representing the mantissa while the exponent is
fixed at -10 (decimal).
During manufacture of the module, offset and gain
correction values are written into the non-volatile memory of
the module. The command VOUT_CAL_OFFSET can be used
to read and/or write the offset (two bytes consisting of a 16bit mantissa in two’s complement format) while the
exponent is always fixed at -10 (decimal). The allowed range
for this offset correction is -125 to 124mV. The command
VOUT_CAL_GAIN can be used to read and/or write the gain
correction - two bytes consisting of a five-bit exponent (fixed
at -8) and a 11-bit mantissa. The range of this correction
factor is -0.125V to +0.121V, with a resolution of 0.004V. The
corrected output voltage reading is then given by:
VOUT ( Final ) =
[VOUT ( Initial ) × (1 + VOUT _ CAL _ GAIN )]
+ VOUT _ CAL _ OFFSET
Measuring Input Voltage Using the PMBus
The module can provide output voltage information using
the READ_VIN command. The command returns two bytes of
data in the linear format. The upper five bits [7:3] of the high
data form the two’s complement representation of the
exponent which is fixed at –5 (decimal). The remaining 11 bits
are used for two’s complement representation of the
mantissa, with the 11th bit fixed at zero since only positive
numbers are valid.
During module manufacture, offset and gain correction
values are written into the non-volatile memory of the
module. The command VIN_CAL_OFFSET can be used to
read and/or write the offset - two bytes consisting of a fivebit exponent (fixed at -5) and a11-bit mantissa in two’s
complement format. The allowed range for this offset
correction is -2 to 1.968V, and the resolution is 32mV. The
command VIN_CAL_GAIN can be used to read and/or write
the gain correction - two bytes consisting of a five-bit
exponent (fixed at -8) and a 11-bit mantissa. The range of
this correction factor is -0.125V to +0.121V, with a resolution
of 0.004V. The corrected output voltage reading is then given
by:
features are supported in these commands. A 1 in the bit
position indicates the fault that is flagged.
STATUS_BYTE : Returns one byte of information with a
summary of the most critical device faults.
Bit
Default
Flag
Position
Value
7
X
0
6
OFF
0
5
VOUT Overvoltage
0
4
IOUT Overcurrent
0
3
VIN Undervoltage
0
2
Temperature
0
1
CML (Comm. Memory Fault)
0
0
None of the above
0
STATUS_WORD : Returns two bytes of information with a
summary of the module’s fault/warning conditions.
Low Byte
Bit
Default
Flag
Position
Value
7
X
0
6
OFF
0
5
VOUT Overvoltage
0
4
IOUT Overcurrent
0
3
VIN Undervoltage
0
2
Temperature
0
1
CML (Comm. Memory Fault)
0
0
None of the above
0
Bit
Position
7
6
5
4
3
2
1
0
High Byte
Flag
VOUT fault or warning
IOUT fault or warning
X
X
POWER_GOOD# (is negated)
X
X
X
Default
Value
0
0
0
0
0
0
0
0
VIN ( Final ) =
[VIN ( Initial ) × (1 + VIN _ CAL _ GAIN )]
+ VIN _ CAL _ OFFSET
Reading the Status of the Module using the PMBus
The module supports a number of status information
commands implemented in PMBus. However, not all
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 23
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
STATUS_VOUT : Returns one byte of information relating to
the status of the module’s output voltage related faults.
Bit
Default
Flag
Position
Value
7
VOUT OV Fault
0
6
X
0
5
X
0
4
VOUT UV Fault
0
3
X
0
2
X
0
1
X
0
0
X
0
STATUS_IOUT : Returns one byte of information relating to
the status of the module’s output voltage related faults.
Bit
Position
7
6
5
4
3
2
1
0
Default
Value
0
0
0
0
0
0
0
0
Flag
IOUT OC Fault
X
IOUT OC Warning
X
X
X
X
X
STATUS_TEMPERATURE : Returns one byte of information
relating to the status of the module’s temperature related
faults.
Bit
Position
7
6
5
4
3
2
1
0
exponent – fixed at -2, and lower 11 bits are mantissa in
two’s complement format – fixed at 12)
MFR_VOUT_MIN : Returns minimum output voltage as two
data bytes of information in Linear format (upper five bits
are exponent – fixed at -10, and lower 11 bits are mantissa
in two’s complement format – fixed at 614)
MFR_SPECIFIC_00 : Returns information related to the type
of module and revision number. Bits [7:2] in the Low Byte
indicate the module type (000001 corresponds to the
UxDT012 series of module), while bits [7:3] indicate the
revision number of the module.
Low Byte
Bit
Position
Flag
Default
Value
7:2
Module Name
000001
1:0
Reserved
10
High Byte
Bit
Position
Flag
Default
Value
7:3
Module Revision Number
None
2:0
Reserved
000
Default
Value
0
0
0
0
0
0
0
0
Flag
OT Fault
OT Warning
X
X
X
X
X
X
STATUS_CML : Returns one byte of information relating to the
status of the module’s communication related faults.
Bit
Position
7
6
5
4
3
2
1
0
Flag
Invalid/Unsupported Command
Invalid/Unsupported Command
Packet Error Check Failed
X
X
X
Other Communication Fault
X
Default
Value
0
0
0
0
0
0
0
0
MFR_VIN_MIN : Returns minimum input voltage as two data
bytes of information in Linear format (upper five bits are
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 24
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Summary of Supported PMBus Commands
Please refer to the PMBus 1.1 specification for more details of these commands.
Table 6
Hex
Code
Command
Non-Volatile
Memory Storage
Brief Description
Turn Module on or off. Also used to margin the output voltage
01
OPERATION
Format
Bit Position
Access
Function
Default Value
7
r/w
On
0
6
r
X
0
5
r/w
0
Unsigned Binary
4
3
2
r/w
r/w
r/w
Margin
0
0
0
1
r
X
X
0
r
X
X
Configures the ON/OFF functionality as a combination of analog ON/OFF pin
and PMBus commands
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r/w
r/w
r/w
r/w
r
Function
X
X
X
pu
cmd
cpr
pol
cpa
Default Value
0
0
0
1
0
1
1
1
02
ON_OFF_CONFIG
03
CLEAR_FAULTS
Clear any fault bits that may have been set, also releases the SMBALERT# signal
if the device has been asserting it.
10
WRITE_PROTECT
Used to control writing to the module via PMBus. Copies the current register
setting in the module whose command code matches the value in the data byte
into non-volatile memory (EEPROM) on the module
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
x
x
x
x
x
Function
bit7
bit6
bit5
X
X
X
X
X
Default Value
0
0
0
X
X
X
X
X
Bit5: 0 – Enables all writes as permitted in bit6 or bit7
1 – Disables all writes except the WRITE_PROTECT, OPERATION
and ON_OFF_CONFIG (bit 6 and bit7 must be 0)
Bit 6: 0 – Enables all writes as permitted in bit5 or bit7
1 – Disables all writes except for the WRITE_PROTECT and
OPERATION commands (bit5 and bit7 must be 0)
Bit7: 0 – Enables all writes as permitted in bit5 or bit6
1 – Disables all writes except for the WRITE_PROTECT command
(bit5 and bit6 must be 0)
11
STORE_DEFAULT_ALL
12
RESTORE_DEFAULT_ALL
Restores all current register settings in the module from values in the module
non-volatile memory (EEPROM)
STORE_DEFAULT_CODE
Copies the current register setting in the module whose command code
matches the value in the data byte into non-volatile memory (EEPROM) on the
module
Bit Position
7
6
5
4
3
2
1
0
Access
w
w
w
w
w
w
w
w
Function
Command code
RESTORE_DEFAULT_CODE
Restores the current register setting in the module whose command code
matches the value in the data byte from the value in the module non-volatile
memory (EEPROM)
Bit Position
7
6
5
4
3
2
1
0
Access
w
w
w
w
w
w
w
w
Function
Command code
VOUT_MODE
The module has MODE set to Linear and Exponent set to -10. These values
cannot be changed
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Function
Mode
Exponent
Default Value
0
0
0
1
0
1
1
0
13
14
20
June 15, 2016
YES
YES
Copies all current register settings in the module into non-volatile memory
(EEPROM) on the module. Takes about 50ms for the command to execute.
©2016 General Electric Company. All rights reserved.
Page 25
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 6 (continued)
Hex
Code
Command
22
VOUT_TRIM
25
VOUT_MARGIN_HIGH
26
VOUT_MARGIN_LOW
29
35
June 15, 2016
Brief Description
Apply a fixed offset voltage to the output voltage command value. Exponent is
fixed at -10. The offset is VOUT_TRIMx2-10
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
High Byte
Default Value
0
0
0
0
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Low Byte
Default Value
0
0
0
0
0
0
0
0
Sets the target voltage for margining the output high. Exponent is fixed at -10.
The offset is (VOUT_MARGIN_HIGH+VOUT_TRIM)x2-10
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
High Byte
Default Value
0
0
0
0
0
1
0
1
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Low Byte
Default Value
0
1
0
0
0
1
1
1
Sets the target voltage for margining the output low. Exponent is fixed at -10.
The offset is (VOUT_MARGIN_LOW+VOUT_TRIM)x2-10
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
High Byte
Default Value
0
0
0
0
0
1
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Low Byte
Default Value
0
1
0
1
0
0
0
1
Non-Volatile
Memory Storage
YES
YES
YES
VOUT_SCALE_LOOP
Sets the scaling of the output voltage – equal to the feedback resistor divider
ratio. VOUT_SCALE_LOOP = 0.6(V)/VOUT(V)
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r/w
r/w
Function
Exponent
Mantissa
Default Value
1
0
1
1
1
0
0
1
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
0
0
0
0
0
0
YES
VIN_ON
Sets the value of input voltage at which the module turns on. This must be
higher than VIN_OFF. Supported Values are
•
2.75V
•
3V to 18V in increments of 0.5V
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Function
Exponent
Mantissa
Default Value
1
1
1
1
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
0
0
1
0
1
1
YES
©2016 General Electric Company. All rights reserved.
Page 26
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 6 (continued)
Hex
Code
36
38
39
40
June 15, 2016
Command
VIN_OFF
IOUT_CAL_GAIN
IOUT_CAL_OFFSET
VOUT_OV_FAULT_LIMIT
Non-Volatile
Memory Storage
Brief Description
Sets the value of input voltage at which the module turns off This must be lower
than VIN_OFF. Supported Values are
•
2.5V to 17.5V in increments of 0.5V
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Function
Exponent
Mantissa
Default Value
1
1
1
1
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
0
0
1
0
1
0
Returns the value of the gain correction term used to correct the measured
output current
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r/w
Function
Exponent
Mantissa
Default Value
1
0
0
0
1
0
0
V
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
V: Variable based on factory calibration
Returns the value of the offset correction term used to correct the measured
output current
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r/w
r
r
Function
Exponent
Mantissa
Default Value
1
1
1
0
0
V
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
V: Variable based on factory calibration
Sets the voltage level for an output overvoltage fault. Exponent is fixed at
Four fixed percentages of 108%, 110%, 112%and 115% are available
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
Function
High Byte
Default Value
0
0
0
0
0
1
0
Bit Position
7
6
5
4
3
2
1
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Low Byte
Default Value
0
0
0
0
1
0
1
©2016 General Electric Company. All rights reserved.
YES
YES
YES
-10.
0
r/w
YES
1
0
r/w
0
Page 27
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Hex
Code
Command
Non-Volatile
Memory Storage
Brief Description
Instructs the module on what action to take in response to an output overvoltage
fault. The options are: RSP[1:0]
00 - Module continues without interruption
01 Module continue s operation for 4 switching cycles and shuts down if
fault persists
01- Module shuts down and responds to RS[2:0]
11 – Module shuts down and attempts to restart
41
44
VOUT_OV_FAULT_RESPONSE
VOUT_UV_FAULT_LIMIT
RS[2:0]
000 – Module does not attempt to restart
111- Module goes through normal startup continuously
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
Access
r/w
r/w
r/w
r/w
r/w
r
RSP
RSP
Function
RS[2] RS[1] RS[0]
X
[1]
[0]
Default Value
1
1
1
1
1
1
YES
1
r
0
r
X
X
0
0
Sets the voltage level for an output undervoltage fault. Exponent is fixed at -10.
Four fixed percentages of 92%, 90%, 88%and 85% are available.
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
High Byte
Default Value
0
0
0
0
0
1
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Low Byte
Default Value
1
0
0
0
1
1
1
1
YES
Instructs the module on what action to take in response to a output
undervoltage fault.
The options are: RSP[1:0]
02 - Module continues without interruption
03 Module continue s operation for 4 switching cycles and shuts down if
fault persists
02- Module shuts down and responds to RS[2:0]
11 – Module shuts down and attempts to restart
45
VOUT_UV_FAULT_RESPONSE
46
June 15, 2016
IOUT_OC_FAULT_LIMIT
RS[2:0]
000 – Module does not attempt to restart
111- Module goes through normal startup continuously.
Format
Unsigned Binary
Bit Position
7
6
5
4
3
Access
r/w
r/w
r/w
r/w
r/w
RSP
RSP
Function
RS[2] RS[1] RS[0]
[1]
[0]
Default Value
0
0
0
0
0
YES
2
r
1
r
0
r
X
X
X
1
0
0
Sets the output overcurrent fault level in A (cannot be changed)
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Exponent
Mantissa
Default Value
1
1
1
1
1
0
0
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
0
0
1
1
1
1
©2016 General Electric Company. All rights reserved.
0
r
0
0
r
YES
1
Page 28
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Hex
Code
Command
4A
IOUT_OC_WARN_LIMIT
5E
POWER_GOOD_ON
Non-Volatile
Memory Storage
Brief Description
Sets the output overcurrent warning level in A
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Exponent
Mantissa
Default Value
1
1
1
1
1
0
0
Bit Position
7
6
5
4
3
2
1
Access
r
r
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
0
1
1
1
0
0
r
0
0
r/w
YES
1
Sets the output voltage level at which the PGOOD pin is asserted high. Exponent
is fixed at -10.
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
High Byte
Default Value
0
0
0
0
0
1
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Low Byte
Default Value
0
1
1
0
1
0
1
0
YES
POWER_GOOD_ON LEVELS
LOW
HIGH
95%
105%
92%
108%
90%
110%
Sets the output voltage level at which the PGOOD pin is de-asserted low.
Exponent is fixed at -10.
5F
POWER_GOOD_OFF
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
High Byte
Default Value
0
0
0
0
0
1
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Low Byte
Default Value
0
0
1
0
0
1
0
1
YES
POWER_GOOD_OFF LEVELS
June 15, 2016
LOW
HIGH
92%
108%
90%
110%
88%
112%
©2016 General Electric Company. All rights reserved.
Page 29
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 6 (continued)
Hex
Code
61
78
79
7A
7B
June 15, 2016
Command
Brief Description
TON_RISE
Sets the rise time of the output voltage during startup. Supported values are
0.6ms, 0.9ms, 1.2ms, 1.8ms, 2.7ms, 4.2ms, 6.0ms, 9.0ms
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r/w
Function
Exponent
Mantissa
Default Value
1
1
1
0
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
1
0
1
0
1
1
STATUS_BYTE
Returns one byte of information with a summary of the most critical module
faults
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
VOUT IOUT_ VIN_U
OTHE
Flag
TEMP CML
X
OFF
_OV
OC
V
R
Default Value
0
0
0
0
0
0
0
0
STATUS_WORD
Returns two bytes of information with a summary of the module’s fault/warning
conditions
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
IOUT_
PGOO
Flag
X
X
X
X
X
VOUT
OC
D
Default Value
0
0
0
0
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
VOUT IOUT_ VIN_U
OTHE
Flag
TEMP CML
X OFF
_OV
OC
V
R
Default Value
0
0
0
0
0
0
0
0
STATUS_VOUT
Returns one byte of information with the status of the module’s output voltage
related faults
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Flag
VOUT_OV
X
X
VOUT_UV
X
X
X
X
Default Value
0
0
0
0
0
0
0
0
STATUS_IOUT
Returns one byte of information with the status of the module’s output current
related faults
Format
Unsigned Binary
Bit Position
7
6
5
4 3 2 1 0
Access
r
r
r
r
r
r r
r
Flag
IOUT_OC
X IOUT_OC_WARN X X X X X
Default Value
0
0
0
0 0 0 0 0
©2016 General Electric Company. All rights reserved.
Non-Volatile
Memory Storage
YES
Page 30
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 6 (continued)
Hex
Code
7D
7E
88
8B
8C
98
June 15, 2016
Command
STATUS_TEMPERATURE
STATUS_CML
READ_VIN
Non-Volatile
Memory Storage
Brief Description
Returns one byte of information with the status of the module’s temperature
related faults
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Flag
OT_FAULT
OT_WARN
X
X
X
X
X
X
Default Value
0
0
0
0
0
0
0
0
Returns one byte of information with the status of the module’s communication
related faults
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Other
Invalid
Invalid PEC
Flag
Comm
X
X
X
X
Command Data Fail
Fault
Default Value
0
0
0
0
0
0
0
0
Returns the value of the input voltage applied to the module
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Exponent
Mantissa
Default Value
1
1
0
1
1
0
0
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
0
0
0
0
0
0
0
r
0
0
r
0
READ_VOUT
Returns the value of the output voltage of the module. Exponent is fixed at -10.
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
0
0
0
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
0
0
0
0
0
0
0
READ_IOUT
Returns the value of the output current of the module
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Exponent
Mantissa
Default Value
1
1
1
0
0
0
0
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
0
0
0
0
0
0
PMBUS_REVISION
0
r
0
0
r
0
Returns one byte indicating the module is compliant to PMBus Spec. 1.1 (read
only)
Format
Unsigned Binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Default Value
0
0
0
1
0
0
0
1
©2016 General Electric Company. All rights reserved.
YES
Page 31
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 6 (continued)
Hex
Code
Command
A0
MFR_VIN_MIN
A4
D0
D4
D5
MFR_VOUT_MIN
MFR_SPECIFIC_00
VOUT_CAL_OFFSET
VOUT_CAL_GAIN
June 15, 2016
Non-Volatile
Memory Storage
Brief Description
Returns the minimum input voltage the module is specified to operate at (read only)
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Function
Exponent
Mantissa
Default Value
1
1
1
1
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
0
0
0
1
1
0
0
YES
Returns the minimum output voltage possible from the module (read only)
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
0
0
0
0
0
1
Bit Position
7
6
5
4
3
2
1
Access
r
r
r
r
r
r
r
Function
Mantissa
Default Value
0
1
1
0
0
1
1
YES
Returns module name information (read only)
Format
Unsigned Binary
Bit Position
7
6
5
4
3
Access
r
r
r
r
r
Function
Reserved
Default Value
0
0
0
0
0
Bit Position
7
6
5
4
3
Access
r
r
r
r
r
Function
Module Name
Default Value
0
0
0
0
0
0
r
0
0
r
0
2
r
1
r
0
2
r
0
0
1
0
r
r
Reserved
X
X
1
0
r
YES
Applies an offset to the READ_VOUT command results to calibrate out offset errors in
module measurements of the output voltage (between -125mV and +124mV).
Exponent is fixed at -10.
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r
r
r
r
r
r
r
Function
Mantissa
Default Value
V
0
0
0
0
0
0
0
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
V
V
V
V
V
V
V
V
YES
Applies a gain correction to the READ_VOUT command results to calibrate out gain
errors in module measurements of the output voltage (between -0.125 and 0.121)
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r
r
r
r/w
Function
Exponent
Mantissa
Default Value
1
1
0
0
0
0
0
V
Bit Position
7
6
5
4
3
2
1
0
Access
r/w
r/w
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
V
V
V
V
V
V
V
V
YES
©2016 General Electric Company. All rights reserved.
Page 32
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Table 6 (continued)
Hex
Code
D6
D7
June 15, 2016
Command
VIN_CAL_OFFSET
VIN_CAL_GAIN
Brief Description
Non-Volatile
Memory
Storage
Applies an offset correction to the READ_VIN command results to calibrate out offset
errors in module measurements of the input voltage (between -2V and +1.968V)
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r/w
r
r
r/w
Function
Exponent
Mantissa
Default Value
1
1
0
1
V
0
0
V
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r/w
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
V
V
V
V
V
V
YES
Applies a gain correction to the READ_VIN command results to calibrate out gain
errors in module measurements of the input voltage (between -0.125 and 0.121)
Format
Linear, two’s complement binary
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r
r/w
r
r
r/w
Function
Exponent
Mantissa
Default Value
1
1
0
0
V
0
0
V
Bit Position
7
6
5
4
3
2
1
0
Access
r
r
r
r/w
r/w
r/w
r/w
r/w
Function
Mantissa
Default Value
0
0
0
V
V
V
V
V
YES
©2016 General Electric Company. All rights reserved.
Page 33
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Thermal Considerations
Power modules operate in a variety of thermal environments;
however, sufficient cooling should always be provided to help
ensure reliable operation.
Considerations include ambient temperature, airflow, module
power dissipation, and the need for increased reliability. A
reduction in the operating temperature of the module will
result in an increase in reliability. The thermal data
presented here is based on physical measurements taken in
a wind tunnel. The test set-up is shown in Figure 48. The
preferred airflow direction for the module is in Figure 49.
output power of the module should not exceed the rated
power of the module (Vo,set x Io,max).
Please refer to the Application Note “Thermal
Characterization Process For Open-Frame Board-Mounted
Power Modules” for a detailed discussion of thermal
aspects including maximum device temperatures.
25.4_
(1.0)
Wind Tunnel
PWBs
Power Module
76.2_
(3.0)
x
12.7_
(0.50)
Probe Location
for measuring
airflow and
ambient
temperature
Air
flow
Figure 48. Thermal Test Setup.
The thermal reference points, Tref used in the specifications
are also shown in Figure 49. For reliable operation the
temperatures at these points should not exceed 120oC. The
June 15, 2016
Figure 49. Preferred airflow direction and location of hotspot of the module (Tref).
©2016 General Electric Company. All rights reserved.
Page 34
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Example Application Circuit
Requirements:
Vin:
12V
Vout:
Iout:
1.8V
9A max., worst case load transient is from 6A to 9A
∆Vout:
1.5% of Vout (27mV) for worst case load transient
Vin, ripple
1.5% of Vin (180mV, p-p)
Vin+
Vout+
VIN
VOUT
VS+
PGOOD
RTUNE
MODULE
CTUNE
SEQ
CI3
CI2
CI1
TRIM
DATA
CO1
CO2
CO3
ADDR0
SMBALRT#
RTrim
ADDR1
ON/OFF
RADDR1
RADDR0
SIG_GND
GND
CI1
SYNC GND
VS-
Decoupling cap - 1x0.047µF/16V ceramic capacitor (e.g. Murata LLL185R71C473MA01)
CI2
2x22µF/16V ceramic capacitor (e.g. Murata GRM32ER61C226KE20)
CI3
47µF/16V bulk electrolytic
CO1
Decoupling cap - 1x0.047µF/16V ceramic capacitor (e.g. Murata LLL185R71C473MA01) + 0.1uF/16V 0402size
ceramic capacitor
CO2
1 x 47µF/6.3V ceramic capacitor (e.g. Murata GRM31CR60J476ME19)
CO3
1 x 330µF/6.3V Polymer (e.g. Sanyo Poscap)
CTune
RTune
2700pF ceramic capacitor (can be 1206, 0805 or 0603 size)
221 ohms SMT resistor (can be 1206, 0805 or 0603 size)
RTrim
10kΩ SMT resistor (can be 1206, 0805 or 0603 size, recommended tolerance of 0.1%)
Note: The DATA, CLK and SMBALRT pins do not have any pull-up resistors inside the module. Typically, the SMBus master
controller will have the pull-up resistors as well as provide the driving source for these signals.
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 35
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Mechanical Outline
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 36
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
2 If
June 15, 2016
PIN
FUNCTION
PIN
FUNCTION
1
2
3
4
5
6
7
8
9
ON/OFF
VIN
SEQ
GND
TRIM
VOUT
VS+
VSPG
10
11
12
13
14
15
16
SYNC2
CLK
DATA
SMBALERT#
SIG_GND
ADDR1
ADDR0
unused, connect to Ground
©2016 General Electric Company. All rights reserved.
Page 37
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Packaging Details
The 12V Digital SlimLynxTM 12A modules are supplied in tape & reel as standard. Modules are shipped in quantities of 600 modules
per reel.
All Dimensions are in millimeters and (in inches).
Reel Dimensions:
Outside Dimensions:
Inside Dimensions:
Tape Width:
June 15, 2016
330.2 mm (13.00)
177.8 mm (7.00”)
44.00 mm (1.732”)
©2016 General Electric Company. All rights reserved.
Page 38
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Pick and Place
The 12A Digital SlimLynxTM modules use an open frame
construction and are designed for a fully automated
assembly process. The modules are fitted with a label
designed to provide a large surface area for pick and place
operations. The label meets all the requirements for surface
mount processing, as well as safety standards, and is able to
withstand reflow temperatures of up to 300oC. The label also
carries product information such as product code, serial
number and the location of manufacture.
Nozzle Recommendations
The module weight has been kept to a minimum by using
open frame construction. Variables such as nozzle size, tip
style, vacuum pressure and placement speed should be
considered to optimize this process. The minimum
recommended inside nozzle diameter for reliable operation is
3mm. The maximum nozzle outer diameter, which will safely
fit within the allowable component spacing, is 7 mm.
Bottom Side / First Side Assembly
The encapsulated SlimLynx product can be assembled on
the bottom side of a customer board. The surface tension of
the solder connections between the customer board and the
module are sufficient to hold the module during the top side
reflow process. No additional glue or adhesive is required.
Lead Free Soldering
The modules are lead-free (Pb-free) and RoHS compliant and
fully compatible in a Pb-free soldering process. Failure to
observe the instructions below may result in the failure of or
cause damage to the modules and can adversely affect
long-term reliability.
not be broken until time of use. Once the original package is
broken, the floor life of the product at conditions of ≤ 30°C
and 60% relative humidity varies according to the MSL rating
(see J-STD-033A). The shelf life for dry packed SMT packages
will be a minimum of 12 months from the bag seal date,
when stored at the following conditions: < 40° C, < 90%
relative humidity.
300
Per J-STD-020 Rev. D
Peak Temp 260°C
250
Reflow Temp (°C)
Surface Mount Information
200
* Min. Time Above 235°C
15 Seconds
Cooling
Zone
150
Heating Zone
1°C/Second
*Time Above 217°C
60 Seconds
100
50
0
Reflow Time (Seconds)
Figure 50. Recommended linear reflow profile using
Sn/Ag/Cu solder.
Post Solder Cleaning and Drying Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The result
of inadequate cleaning and drying can affect both the
reliability of a power module and the testability of the
finished circuit-board assembly. For guidance on
appropriate soldering, cleaning and drying procedures, refer
to Board Mounted Power Modules: Soldering and Cleaning
Application Note (AN04-001).
Pb-free Reflow Profile
Power Systems will comply with J-STD-020 Rev. D
(Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices) for both Pb-free solder
profiles and MSL classification procedures. This standard
provides a recommended forced-air-convection reflow
profile based on the volume and thickness of the package
(table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu
(SAC). The recommended linear reflow profile using Sn/Ag/Cu
solder is shown in Fig. 50. Soldering outside of the
recommended profile requires testing to verify results and
performance.
MSL Rating
The 12A Digital SlimLynxTM modules have a MSL rating of 3.
Storage and Handling
The recommended storage environment and handling
procedures for moisture-sensitive surface mount packages is
detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and
Use of Moisture/Reflow Sensitive Surface Mount Devices).
Moisture barrier bags (MBB) with desiccant are required for
MSL ratings of 2 or greater. These sealed packages should
June 15, 2016
©2016 General Electric Company. All rights reserved.
Page 39
GE
Data Sheet
12A Digital SlimLynxTM: Non-Isolated DC-DC Power Modules
3Vdc –14.4Vdc input; 0.45Vdc to 5.5Vdc output; 12A Output Current
Ordering Information
Please contact your GE Sales Representative for pricing, availability and optional features.
Table 7. Device Codes
Device Code
Input
Voltage Range
Output
Voltage
Output
Current
On/Off
Logic
Sequencing
Comcodes
ULDT012A0X3-SRZ
3 – 14.4Vdc
0.45 – 5.5 Vdc
12A
Negative
Yes
CC109159703
ULDT012A0X43-SRZ
3 – 14.4Vdc
0.45 – 5.5 Vdc
12A
Positive
Yes
150037553
On/Off
logic
Remote
Sense
Options
3
-SR
Z
3 = Remote
Sense
S = Surface
Mount
Z = ROHS6
-Z refers to RoHS compliant parts
Table 8. Coding Scheme
Package
Identifier
Family
U
LD
T
012A0
P=Pico
LD=SlimLynx
Digital
Encapsulated
T=with EZ
Sequence
12A
U=Micro
M=Mega
G=Giga
Sequencing Output
Option
current
X=without
LV=SlimLynx sequencing
Analog
Encapsulated
Output
voltage
X
X=
4=
programm positive
able output
No entry =
negative
ROHS Compliance
R = Tape &
Reel
GE Digital Non-Isolated DC-DC products use technology licensed from Power-One, protected by US patents: US20040246754, US2004090219A1, US2004093533A1, US2004123164A1,
US2004123167A1, US2004178780A1, US2004179382A1, US20050200344, US20050223252, US2005289373A1, US20060061214, US2006015616A1, US20060174145, US20070226526,
US20070234095, US20070240000, US20080052551, US20080072080, US20080186006, US6741099, US6788036, US6936999, US6949916, US7000125, US7049798, US7068021, US7080265,
US7249267, US7266709, US7315156, US7372682, US7373527, US7394445, US7456617, US7459892, US7493504, US7526660.
Outside the US the Power-One licensed technology is protected by patents: AU3287379AA, AU3287437AA, AU3290643AA, AU3291357AA, CN10371856C, CN1045261OC, CN10458656C,
CN10459360C, CN10465848C, CN11069332A, CN11124619A, CN11346682A, CN1685299A, CN1685459A, CN1685582A, CN1685583A, CN1698023A, CN1802619A, EP1561156A1, EP1561268A2,
EP1576710A1, EP1576711A1, EP1604254A4, EP1604264A4, EP1714369A2, EP1745536A4, EP1769382A4, EP1899789A2, EP1984801A2, W004044718A1, W004045042A3, W004045042C1,
W004062061 A1, W004062062A1, W004070780A3, W004084390A3, W004084391A3, W005079227A3, W005081771A3, W006019569A3, W02007001584A3, W02007094935A3
Contact Us
For more information, call us at
USA/Canada:
+1 877 546 3243, or +1 972 244 9288
Asia-Pacific:
+86.021.54279977*808
Europe, Middle-East and Africa:
+49.89.878067-280
www.gecriticalpower.com
GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no
liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s)
or information.
June 15, 2016
©2016 General Electric Company. All International rights reserved.
Version 1.4
工商网监
湘ICP备2023018690号
