CC2520330K3

SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 1 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520□□□□3 □-□□□ Ⅰ﹒CONFIGURATION & DIMENSIONS： A A B C B E F Not Marking : 2.5±0.2 : 2.0±0.1 : 1.8±0.1 : 1.4±0.1 : 0.40 m/m m/m m/m m/m m/m 0.50 C 0.9 1.5 0.9 F F E （ PCB Pattern ） Ⅱ﹒SCHEMATIC DIAGRAM： d Ⅲ﹒MATERIALS： a﹒Core： Ferrite DR core b﹒Wire ：Enamelled copper wire c﹒Terminal：Cu/Sn d﹒Encapsulate：Epoxy novolac molding compound e﹒Remark：Products comply with RoHS' requirements Peak Temp：245℃ max. Max time above 225℃ ： 30sec max. Max time above 200℃ ： 50sec max. Temperature Rising Area 2 ~ 4℃ / sec Preheat Area 150 ~ 180℃ / 90 ~ 150sec Reflow Area 2 ~ 4℃ / sec 240±5℃ 1.5 a c b Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：20℃ max. b﹒Ambient temp.： 80℃ max. c﹒Storage temp.：-40℃ ----+100℃ d﹒Operating temp.：-40℃ ----+85℃ e﹒Terminal strength：0.5 kg min. f﹒Rated current：Current cause inductance drop within 10% g﹒Resistance to solder heat：260℃.10 secs. h﹒Resistance to solvent：Per MIL-STD-202F AR-001A Temperature ( ℃ ) Forced Cooling Area 3 ~ 5℃ / sec 250 200 150 100 50 10sec 30sec max. ( 20~30sec ) 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 2 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520□□□□3□-□□□ Ⅴ﹒ELECTRICAL CHARACTERISTICS： DWG No. CC25201R0M3□-□□□ CC25201R5M3□-□□□ CC25202R2M3□-□□□ CC25203R3M3□-□□□ CC25204R7M3□-□□□ CC25206R8M3□-□□□ CC2520100K3□-□□□ CC2520150K3□-□□□ CC2520220K3□-□□□ CC2520330K3□-□□□ Inductance ( µH ) 1.0±20% 1.5±20% 2.2±20% 3.3±20% 4.7±20% 6.8±20% 10.0±10% 15.0±10% 22.0±10% 33.0±10% Q typ. 20 20 20 20 20 20 30 30 30 30 Test Freq ( MHz ) 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 SRF ( MHz ) min. 200 165 95 55 43 39 32 21 18 16 RDC (Ω) ±30％ 0.34 0.42 0.50 0.65 0.80 1.00 1.69 2.20 2.80 4.20 IDC ( mA ) max. 475 435 390 340 285 275 210 175 160 120 1)．□ : Packaging information… A : Bulk 2)．"- □□□ ":Reference code B : Taping Reel AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 3 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520 □□□□3 □-□□□ Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape 2.0±0.5 A B N ∮C ∮C D G Embossed Carrier ※ Carrier Tape Width : D P:4 m/m 4 m/m End Start Leader no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07 - 08 A 178 B 21±0.8 C 13 D 8 G 10 +0 N 50 -0 Unit:m/m T 12.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series CC2520 Q'TY (pcs) G.W. (gw) Outer : Carton Style 07 - 08 Q'TY (pcs) G.W. (Kg) Size (cm) 41 x 39 x 22 2,000 60 100,000 5.0 AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 4 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520 □□□□3 □-□□□ Ⅶ﹒DWGING NUMBER EXPRESSION： C C 2 5 2 0 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1： Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code A B Inner package T.B.D. T / R ( Reel package ) Inner package Q'TY T.B.D. 2000 pcs Remark AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 5 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520 □□□□3□-□□□ Ⅷ﹒RELIABILITY TEST： Test item Specification Test condition / Test method Electrical performance test Inductance L Q Self resonance frequency SRF DC Resistance RDC Rated current IDC □HP4194A with HP-16034E test fixture Refer to standard electrical characteristic list □HP4291A with HP-16093A test fixture CH-502AC Applied the current to coils，The Temperature rise test 20℃ max. After test， Inductors shall be no evidence of electrical and mechanical damage After tset， Inductors shall be no evidence of electrical and mechanical damage 1000 MΩ min﹒ Inductance change shall be less than 10% to initial value & temperature rise shall not be more than 20℃ 1 ﹒Applied the allowed DC current for 10 minutes 2 ﹒Temperature measure by digital surface thermometer Applied 2 times of rated allowed DC current to inductor for a period of 5 minutes AC voltage of 1000VAC applied between inductors terminal and coating for 5 seconds 100 VDC applied between inductor terminal and coating Over load test Withstanding voltage test Insulation resistance test Mechanical performance test Vibration test ( Low frequency ) 1 ﹒Inductors shall be no evidence of electrical and mechanical damage 1 ﹒Amplitude：1.5 m/m 2 ﹒Frequency ：10 -- 55 -- 10 Hz / 1min. 3 ﹒Direction：X，Y，Z 4 ﹒Duration：2 hrs / X，Y，Z Inductors shall be dropped 10 times from a height of 1m onto 3cm wooden board Temp：260±5℃ Time：10±1.0 sec. Shock test Resistance to soldering heat 2 ﹒Inductance shall not change more than±5% 3 ﹒Q Shall not change more than ±20% AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 6 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520 □□□□3 □-□□□ Terminal strength-pull test Terminal shall not be loosened or ruptured A 0.5kg load shall be applied to both Terminals in the axis direction for 1 minute﹒ After fluxing ，Inductor shall be dipped in a melted solder bath at 230±5℃ for 5 seconds﹒ Solderability test The terminal shall be at least 90% covered with solder There shall be no case deformation change in appearance or obliteration of marking Resistance to solvent test MIL-STD-202F，Method 215D Climatic test Temperature characteristic Humidity test Cold test 1 ﹒Inductors shall be no evidence of electrical and mechanical damage 2 ﹒Inductance shall not change more than ±10% 3 ﹒Q shall not change more than ±20% -25℃ -- 85℃ 1 ﹒Temp ：40±2℃ 2 ﹒R.H.：90 -- 95% 3 ﹒Time：96±2 hours 1 ﹒Temp：-25±2℃ 2 ﹒Time：96±2 hours Room temp 15 mins Room temp 15 mins Total：5 cycles 1 ﹒Temp ：85±2℃ 2 ﹒Time：96±2 hours 1 ﹒Temp ：85±2℃ 2 ﹒Time：1000±12 hours 3 ﹒Load：Allowed DC current 1 ﹒Temp ：40±2℃ 2 ﹒R.H.：90 -- 95% 3 ﹒Time：1000±12 hours 4 ﹒Load：Allowed DC current Thermal shock test -25±2℃ 30 mins 85±2℃ 30 mins Dry heat test High temperature load life test Humidity load life There shall be no evidence of short or open circuiting Note： Unless otherwise specified , Allow the specimen to stand at room temperature for 1 hour or more but not more than 2 hours , Measure the electrical and mechanical performances AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 7 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520 □□□□3□-□□□ Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN AIW CFUEWB E IAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW 287806002 Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane BC Coat Typ ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 ANSI Type Temp Class 220 130 200 180 200 ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 Page 1 of 2 A not-for-profit organization dedicated to public safety and committed to quality service SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ ____ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane BC Coat Typ Polyamide ____ ____ ____ Nylon Polyamide OC MW80C MW2-C ___ MW75C MW28-C MW28-C ANSI Type Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 8 WOUND CHIP INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. CC2520□□□□3 □-□□□ OMFZ2 March 4, 1994 E59481 (S) BM-21 BM-22 BM-23 EME-1100 EME-1200 EME-5961C ALL ALL ALL BK BK BK BK BK BK 0.79 0.79 0.79 0.84 6.4 0.84 6.4 0.3 3.1 94HB 94HB 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 50 50 50 130 130 130 130 130 130 50 50 50 130 130 130 130 130 130 50 50 50 130 130 130 130 130 130 __________________ Reports: January 19, 1988: January 19, 1988: January 19, 1988: June 2, 1988; June 2, 1998; June 2, 1988. R AR-001A