ESR0604100ML

SPECIFICATION FOR APPROVAL REF : PROD. NAME ABC'S DWG NO. PAGE: 1 ESR0604□□□□L□-□□□ SMD POWER INDUCTOR ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： A A : 5.8±0.3 5.2±0.3 4.5±0.3 1.3 ref. 1.7 ref. 5.5 ref. 6.0 ref. m/m m/m m/m m/m m/m m/m m/m 100 B B: C: D G H : : : D H G I C I: ( PCB Pattern ) Ⅱ﹒SCHEMATIC DIAGRAM： a b Ⅲ﹒MATERIALS： a ﹒Core：Ferrite DR core b﹒Wire ：Enamelled copper wire (Class F & H) c ﹒Terminal： Ag/Ni/Sn d﹒Remark：Products comply with RoHS' requirements 250 Peak Temp：245±5℃ Max time above 200℃ ： 60sec max. Temperature Rising Area +4.0℃ / sec max. Preheat Area 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area c +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. Peak Temperature: 245±5℃ Ⅳ﹒GENERAL SPECIFICATION： a﹒Storage temp.：-40℃ ----+125℃ b﹒Operating temp.：-40℃----+105℃ c﹒Resistance to solder heat：245±5℃.10 secs. Tempe ra tu re ( ℃ ) 200 150 60sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME ABC'S DWG NO. PAGE: 2 ESR0604□□□□L□-□□□ SMD POWER INDUCTOR ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISITCS： Inductance ( μH ) 10±20% 12±20% 15±20% 18±20% 22±20% 27±20% 33±20% 39±20% 47±20% 56±10% 68±10% 82±10% 100±10% 120±10% 150±10% 180±10% 220±10% RDC ( mΩ ) max. typ. 62 69 87 114 128 140 184 215 258 298 343 436 559 599 900 986 1222 100 120 140 150 180 200 230 320 370 420 460 600 700 900 1100 1380 1570 Rated Current (A) 1.69 1.53 1.44 1.42 1.26 1.17 0.99 0.90 0.81 0.77 0.65 0.63 0.61 0.59 0.52 0.47 0.38 SRF (MHz) ref. 32.0 29.0 26.0 24.0 19.0 18.0 17.0 17.0 14.0 12.0 11.0 8.0 7.5 7.5 7.0 6.5 6.5 DWG No. ESR0604100ML□ -□□□ ESR0604120ML□ -□□□ ESR0604150ML□ -□□□ ESR0604180ML□ -□□□ ESR0604220ML□ -□□□ ESR0604270ML□ -□□□ ESR0604330ML□ -□□□ ESR0604390ML□ -□□□ ESR0604470ML□ -□□□ ESR0604560KL□ -□□□ ESR0604680KL□ -□□□ ESR0604820KL□ -□□□ ESR0604101KL□ -□□□ ESR0604121KL□ -□□□ ESR0604151KL□ -□□□ ESR0604181KL□ -□□□ ESR0604221KL□ -□□□ 1). □：Packaging information… A：Bulk B：Taping Reel 2)."":Reference code 3). Inductance test condition :10uH~82uH at 1MHz/1V 100uH~220uH at 1KHz/1V 4). Rated current: The DC current at which the inductance decreases to 90% of it's initial value or when Δt=40℃,whichever is lower(Ta=20℃) □□□ AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME ABC'S DWG NO. P AGE: 3 ESR0604□□□□L□-□□□ SMD POWER INDUCTOR ABC'S ITEM NO. Ⅵ﹒INDUCTANCE VS. DC CURRENT CURVE： ( 1 ) Configuration T Cover tape 2.0±0.5 A B ∮C ∮C N G D Embossed carrier ※Carrier tape width : D P:12 m/m End 4 m/m Start 100 100 100 100 100 100 Leader no component 350 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Unit:m/m Style 13 - 16 A 330 B 21±0.8 C 13±0.5 D 16 G 18 +0 N 50 -0 T 22.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) Outer : Carton ESR0604 1000 780 13 - 16 6,000 7.4 40 x 40 x 24 AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME ABC'S DWG NO. PAGE: 4 ESR0604□□□□L□-□□□ SMD POWER INDUCTOR ABC'S ITEM NO. Ⅶ﹒PACKAGING INFORMATION： E S R 0 6 0 4 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code E : Economy Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code A B T.B.D. T / R ( Reel package ) Inner package Inner package Q'TY T.B.D. 1,000 pcs Remark AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME ABC'S DWG NO. PAGE: 5 ESR0604 □□□□L□-□□□ SMD POWER INDUCTOR ABC'S ITEM NO. Ⅷ﹒DWGING NUMBER EXPRESSION： Test item Specification Test condition Preheat : 155℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Solderability More than 95% of the terminal electrode Shall be covered With fresh solder. Thermal shock test ( Temp. cycle ) Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -40 ℃ 30 minutes +105 ℃ 30 minutes Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME ABC'S DWG NO. PAGE: 6 ESR0604□□□□L□-□□□ SMD POWER INDUCTOR ABC'S ITEM NO. Ⅸ﹒RELIABILITY TEST： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS S F.BW@ SFFW 287806002 Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane Coat Typ ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC ANSI Type MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 Temp Class 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 Page 1 of 2 A not-for-profit organization dedicated to public safety and committed to quality service Mtl Dsg SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mark Dsg ____ ____ ____ ____ ____ ____ BC Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Coat Typ OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type MW80C MW2-C ___ MW75C MW28-C MW28-C Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2 ⁄E174837 September 8 , 2000 AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME ABC'S DWG NO. PAGE: 7 ESR0604□□□□L□-□□□ SMD POWER INDUCTOR ABC'S ITEM NO. OBMW2 Magnet Wire-Comporent October 06, 2005 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD JALAN DAMAI SATU JANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 180 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Polysol P155p Mark Dsg E180 A200 PN155 P155, G155 Pg155 Pp155,Gp155 P160 P180,G180 P170 or G170 PN180 P155p BC Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ____ ANSI Typ MW-77 MW-74 MW-80, MW-28 MW-79, MW-75 MW-75 MW-79 MW-79 MW-82 MW-79 MW-79 MW-83 MW-79 Temp Class 180 200 155, 130 155, 130 130 155 155 180 155 155 180 155 Marking ：Company name, material designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A