SB5011101ML

SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 1 SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SB5011□□□□L□-□□□ Ⅰ﹒CONFIGURATION & DIMENSIONS： A 4 3 A B C D E F G H I J K L M L : 5.60 : 6.00 : : : : : : : : : : 1.15 1.00 5.20 3.20 0.80 1.30 2.00 6.40 4.60 1.30 ±0.3 ±0.3 ±0.1 typ. typ. typ. ref. ref. ref. ref. ref. ref. ref. m/m m/m m/m m/m m/m m/m m/m m/m m/m m/m m/m m/m m/m 100 1 2 C B D G D H I H : 3.80 E F K ( PCB Pattern Suggestion ) Ⅱ﹒SCHEMATIC DIAGRAM： 1 3 L M a b d Peak Temp：260 ℃ m ax. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. Temperature Rising Area +4.0℃ / sec max. Preheat Area 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area +2.0 ~ 4.0℃ / sec max. Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 50sec max. 230℃ Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core b﹒Base：PCB Base FR4 c﹒Adhesive ：Epoxy resin d﹒Wire：Enamelled copper wire （class F） e﹒Terminal：Cu/Ni/Au f﹒Remark：Products comply with RoHS' requirements 250 Temperature ( ℃ ) J 100 c Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：40℃ typ. b﹒Storage Temp.：-40℃ ----+125℃ c﹒Operating Temp.：-40℃----+125℃ ( Temp. rise Included ) d﹒Resistance to solder heat ：260℃.10 secs. AE-001A 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 2 SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SB5011□□□□L□-□□□ Ⅴ﹒ELECTRICAL CHARACTERISTICS ： DWG No. SB50111R0ML□-□□□ SB50112R2ML□-□□□ SB50113R3ML□-□□□ SB50114R7ML□-□□□ SB50116R8ML□-□□□ SB5011100ML□-□□□ SB5011150ML□-□□□ SB5011220ML□-□□□ SB5011330ML□-□□□ SB5011470ML□-□□□ SB5011680ML□-□□□ SB5011101ML□-□□□ Inductance ( µH ) 1.0±20% 2.2±20% 3.3±20% 4.7±20% 6.8±20% 10.0±20% 22.0±20% 22.0±20% 33.0±20% 47.0±20% 68.0±20% 100.0±20% Test Freq. ( Hz ) 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K RDC (Ω ) max. 0.053 0.082 0.128 0.158 0.230 0.380 0.580 0.760 1.050 1.580 2.300 3.600 Irms (A) typ. 1.60 1.30 1.05 0.96 0.80 0.62 0.46 0.40 0.30 0.25 0.20 0.16 Isat (A) typ. 2.50 1.70 1.40 1.20 1.05 0.80 0.62 0.52 0.42 0.35 0.30 0.24 1). □：Packaging information … A：Bulk B：Taping Reel 2). "- □□□":Reference code 3).Inductance Test Freq : 100KHz / 1V 4). Irms Base on Temp. rise 40℃ typ. Isat Bae on △L/L0A=10 % typ. @ Inductance VS. DC Superposition Characteristics 1000 100 Inductance ( uH ) 101 330 10 100 3R3 1 0.1 0.01 0.1 1 10 DC Current ( A ) AE-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 3 SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SB5011□□□□L□-□□□ Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T 2.0±0.5 Cover Tape A B ∮C ∮C N G D Embossed carrier P:8 m/m End ※Carrier Tape width : D 4 m/m Start 100 100 100 100 100 Leader no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07-12 A 178 B 21±0.8 C 13 D 12 G 14 +0 N 50 -0 Unit:m/m T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SB5011 AE-001A Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) Outer : Carton G.W. (Kg) Size (cm) 1200 120 07-12 48000 4.6 42 x 41 x 24 SPECIFICATION FOR APPROVAL REF : PROD. NAME P AGE: 4 SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SB5011□□□□L□-□□□ Ⅶ﹒DWGING NUMBER EXPRESSION： S B 5 0 1 1 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1： Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9： Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Remark Code A B Inner package T.B.D. T / R ( Reel package ) Inner package Q'TY T.B.D. 1200 pcs AE-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME P AGE: 5 SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SB5011□□□□L□-□□□ Ⅷ﹒RELIABILITY TEST： Test item Specification More than 90% of the terminal electrode Shall be covered With fresh solder. Test condition Preheat : 150±25℃ for 60 seconds Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 4±1 seconds Solderability Thermal shock test ( Temp. cycle ) Inductance shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -25±2 ℃ 30 minutes 85±2 ℃ 30 minutes Humidity Resistance test Temperature : 40±2℃ Humidity : 90 ~ 95% Applied current : Per spec. Time : 500 hours High temp. Resistance test Temperature : 85±2℃ Applied current : Per spec. Time : 500 hours AE-001A SPECIFICATION FOR APPROVAL REF : P ROD. NAME P AGE: 6 SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SB5011□□□□L□-□□□ Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW 287806002 Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane BC Coat Typ ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 ANSI Type Temp Class 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 Page 1 of 2 A not-for-profit organization dedicated to public safety and committed to quality service SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ ____ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane BC Coat Typ Polyamide ____ ____ ____ Nylon Polyamide OC MW80C MW2-C ___ MW75C MW28-C MW28-C ANSI Type Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2 ⁄E174837 September 8 , 2000 AE-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME P AGE: 7 SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SB5011□□□□ L□-□□□ QMTS2 September 20, 2000 Polymeric Materials-Filament-wound Tubing. Industrial Laminates. Vulcanized Fiber, and Materials for Use in Fabricating Recognized Printed Wiring Boards Component TAIWAN LEADER COPPER CLAD LAMINATE CO LTD Base Mtl Min ANSI Thick Type In. (mm) Clad Cond Thick Min Mils (Mks) Max Mils (Mks) Max Area Dla In. (mm) E176891 Clad Mil Deg Soldering Temp Time C Sec UL94 Flame Class Max Oper T emp Metal clad industriai laminates for use in printed wiring boards, furnished in the form of sheets with copper cladding on one or both sides. JL-180L LS-4 LS-4Y FR-5 FR-4 FR-4 0.025 0.015 0.015 0.015 (0.63) (0.38) (0.38) (0.38) 0.67 0.68 0.68 0.67 (17) (17) (17) (17) 2.68 2.68 2.68 2.68 (68) (68) (68) (68) 2.0 2.0 1.5 2.0 (50.8) (50.8) (38.1) (50.8) 300 280 288 288 30 30 30 30 94V-0 94V-0 94V-0 94V-0 140 130 130 130 Underwriters Laboratories Inc. R AE-001A