SF1358101YL

SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 1 SMD LINE FILTER ABC'S DWG NO. ABC'S ITEM NO. SF1358□□□□L□-□□□ Ⅰ﹒CONFIGURATION & DIMENSIONS： A D A: B: 13.50 max. 10.50 max. 6.10 max. 9.50 ±0.2 2.50 ±0.2 1.20 max. 2.2 m/m m/m m/m m/m m/m m/m 2.2 101Y Marking Inductance code C: B D: E: W∮ : C 10.3 W∮ 1.2 2.5 14.7 ( PCB Pattern ) Ⅱ﹒SCHEMATIC DIAGRAM： STYLE "A" 1 8 STYLE "B" N1 a d c N1 2 3 7 6 5 1 4 8 5 N2 4 N2 " " : Polarity e b Ⅲ﹒MATERIALS： a﹒ Core：Ferrite T core b﹒Case：DAP WH9100 c﹒ Wire：Enamelled copper wire ( class B or F ) d﹒Adhesive：Epoxy resin e﹒ Terminal： Tinned copper plate f﹒Remark： Products comply with RoHS' requirements 250 Peak Temp： 260 ℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. Temperature Rising Area +4.0℃ / sec max. Preheat Area Reflow Area +2.0 ~ 4.0℃ / sec max. Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 150 ~ 200 ℃ / 60 ~ 120sec 50sec max. 230℃ Ⅳ﹒ENVIRONMENTAL SPECIFICATION： a﹒Temp. rise： 45℃ max. b﹒Storage temp .：-40℃ ----+85℃ c﹒Operating ambient temp .： -40℃ ----+80℃ d﹒ Resistance to solder heat ：260℃. 10 secs. AE-001A Temperature ( ℃ ) 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 REF : PROD. NAME SPECIFICATION FOR APPROVAL SMD LINE FILTER ABC'S DWG NO. ABC'S ITEM NO. SF1358□□□□L□-□□□ PAGE: 2 Ⅴ﹒ELECTRICAL CHARACTERISTICS： Inductance ( uH ) 0.1 V , 100 KHZ L1 , L2 SF1358350YL□ - □□□ SF1358600YL□ - □□□ SF1358101YL□ - □□□ SF1358251YL□ - □□□ SF1358501YL□ - □□□ 35±35% 60±35% DC resistance | L1-L2 | N1 , N2 ( Ω ) 4 max. 5 max. 0.035 max. 0.065 max. 0.100 max. 0.150 max. Rated current (A) 2.70 max. 2.00 max. 0.70 max. 0.60 max. 0.40 max. 0.35 max. 600 Vac 60 Hz 3 mA 3 sec. HI-POT test Impedance (Ω) Freq. range ( MHz ) DWG NO. Style B B A A A A 400 min. 5 ~ 250 600 min. 5 ~ 100 300 min. 1 ~ 50 600 min. 1 ~ 40 1200 min. 1 ~ 40 2200 min. 0.5 ~ 10 100±35% 15 max. 250±35% 25 max. 500±35% 35 max.. 0.300 max. 0.400 max. SF1358102YL□ - □□□ 1000±35% 45 max. 1). □： Packaging information … A：Bulk B：Taping Reel 2)."3). Temp. rise : 45℃ max. at rated current 4). Test equipment : HP-4284A □□□ ":Reference code Ⅵ﹒IMPEDANCE VS﹒FREQUENCY ： 10 5 IMPEDANCE ( KΩ) 6 : SF1358102Y 5 : SF1358501Y 4 : SF1358251Y 3 : SF1358101Y 2 : SF1358600Y 1 : SF1358350Y 1 0.5 6 MEASURING CIRCUIT : 5 4 0.1 3 2 1 0.05 RF IMPEDANCE ANALYZER 0.01 0.1 1 10 100 300 FREQUENCY ( MHz ) AE-001A REF : PROD. NAME SPECIFICATION FOR APPROVAL SMD LINE FILTER ABC'S DWG NO. ABC'S ITEM NO. SF1358□□□□L□-□□□ PAGE: 3 Ⅶ﹒PACKAGING INFORMATION： ( 1 ) Configuration T C over Tape 2.0±0.5 A N ∮C ∮C B G D Embossed carrier ※ Carrier tape width : D P:16 m/m 4 m/m End Start 101Y 101Y 101Y 101Y 101Y Leader no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 13 - 24 A 330 B 21±0.8 C 13±0.5 D 24 G 26 +0 N 50 -0 Unit:m/m T 30.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SF1358 Q 'TY (pcs) G.W. (gw) Style Q'TY (pcs) Outer : Carton G.W. (Kg) Size (cm) 600 700 13 - 24 2,400 6.5 40 x 40 x 24 AE-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 4 SMD LINE FILTER ABC'S DWG NO. ABC'S ITEM NO. SF1358□□□□L□-□□□ Ⅷ﹒DWGING NUMBER EXPRESSION： S F 1 3 5 8 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1： Product Classification L： Lead Free Standard products comply with RoHS' requirements 1 ~ 9： Lead Free Special products comply with RoHS' requirements Appendix code 2： Package Information Code A B Inner package T.B.D. T / R ( Reel package ) Inner package Q'TY T.B.D. 600 pcs Remark AE-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 5 SMD LINE FILTER ABC'S DWG NO. ABC'S ITEM NO. SF1358□□□□L□-□□□ Ⅸ﹒RELIABILITY TEST： Test item Specification More than 90% of the terminal electrode Shall be covered With fresh solder. Test condition Preheat : 150±25℃ for 60 seconds Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 4±1 seconds Solderability Thermal shock test ( Temp. cycle ) Inductance shall not change more than ± 30% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -25±2 ℃ 30 minutes 85±2 ℃ 30 minutes Humidity Resistance test Temperature : 40±2℃ Humidity : 90 ~ 95% Applied current : Per spec. Time : 500 hours High temp. Resistance test Temperature : 105±2℃ Applied current : Per spec. Time : 500 hours AE-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 6 SMD LINE FILTER ABC'S DWG NO. ABC'S ITEM NO. SF1358□□□□L□-□□□ Ⅹ﹒DWG EXPRESSION： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW 287806002 Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane BC Coat Typ OC ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 ANSI Type Temp Class 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 Page 1 of 2 A not-for-profit organization dedicated to public safety and committed to quality service SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ ____ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane BC Coat Typ Polyamide ____ ____ ____ Nylon Polyamide OC MW80C MW2-C ___ MW75C MW28-C MW28-C ANSI Type Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 AE-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 7 SMD LINE FILTER ABC'S DWG NO. ABC'S ITEM NO. SF1358□□□□L□-□□□ QMFZ2 Component - Plastics Friday , October 24, 2003 E150608 WAH HONG INDUSTRIAL CORP 10TH FL 235 CHUNG CHENG 4TH RD KAOHSIUNG TAIWAN Material Designation: Product Description: Diallyl Phthalate ( DAP ), molding compound, furnished as pellets. Color BK BK Min. Thick. (m/m) 0.37 0.82 Flame Class V-0 V-0 HVTR: 0 HWI HAI 0 2 3 0 x RTI RTI Elec Imp 130 130 D495: 4 130 130 RTI Str 130 130 IEC GWIT IEC GWFI CTI: 0 Dielectric Strength (kV/m/m): ISO Tensile Strength (MPa): ISO Tensile Impact (kJ/m 2): Report Date: 8/18/1998 IEC Ball Pressure (℃): Dimensional Stability (%): ISO Heat Deflection (℃): ISO Charpy Impact (kJ/m 2): R Volume Resistivity (10 ohm-cm): ISO Flexural Strength (MPa): ISO Izod Impact (kJ/m 2 ): Underwriters Laboratories Inc UL94 small-scale test data does not pertain to building materials, furnishings and related contents. UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in components and parts of end-product devices and appliances, where the acceptability of the combination is determined by ULI. AE-001A