SH30114R7Y2

SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 1 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SH3011□□□□2□-□□□ Ⅰ﹒CONFIGURATION & DIMENSIONS： A Marking (White) A B C D E G H I R : : : : : : : : : 3.80 ±0.30 3.80 ±0.30 1.15 ±0.15 1.30 typ. 1.20 typ. 1.10 ref. 4.30 ref. 1.60 ref. 1.30 ref. H I m/m m/m m/m m/m m/m m/m m/m m/m m/m 100 C B R D E ( PCB Pattern Suggestion ) Ⅱ﹒SCHEMATIC DIAGRAM： LCR Meter Ⅲ﹒MATERIALS： a﹒ Core： Ferrite DR core b﹒Core： Ferrite RI core c﹒Wire ：Enamelled copper wire ( Class F ) d﹒Adhesive ：Epoxy resin e﹒Terminal：Ag/Ni/Sn f﹒Remark： Products comply with RoHS' requirements D a b c d Peak Temp：260℃ max. Max time above 230℃ ： 50sec max. Max time above 200℃ ： 70sec max. Temperature R ising Area +4.0℃ / sec max. Preheat Area 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area I e Forced Cooling Area +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. Peak Temperature: 260℃ 50sec max. 230℃ 250 Temperature ( ℃ ) Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：40℃ typ. b﹒Storage temp.：-40℃ ----+125℃ c﹒Operating temp.：-40℃----+105℃ d﹒Resistance to solder heat：260℃.10 secs. 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) G 200 250 AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 2 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SH3011□□□□2□-□□□ Ⅴ﹒ ELECTRICAL CHARACTERISTICS： DWG No. SH30111R5Y2□ -□□□ SH30112R2Y2□ -□□□ SH30113R3Y2□ -□□□ SH30114R7Y2□ -□□□ SH30116R8Y2□ -□□□ SH3011100Y2□ -□□□ SH3011150Y2□ -□□□ SH3011220Y2□ -□□□ SH3011330Y2□ -□□□ SH3011470Y2□ -□□□ 1)﹒ 2)."Inductance ( µH ) 1.5 ± 30 ％ 2.2 ± 30 ％ 3.3 ± 30 ％ 4.7 ± 30 ％ 6.8 ± 30 ％ 10.0 ± 30 ％ 15.0 ± 30 ％ 22.0 ± 30 ％ 33.0 ± 30 ％ 47.0 ± 30 ％ Q ref. 7 7 6 7 6 6 6 6 6 4 Test Freq. SRF ( MHz ) ( MHz ) typ. 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 B ：Taping Reel 130 120 100 80 70 50 40 30 25 20 RDC ( mΩ ) typ. max. 68 105 130 185 270 415 720 1150 1550 2400 88 135 170 240 340 520 900 1450 1900 2750 Irms ( mA ) typ. 1900 1600 1400 1200 1000 800 650 540 440 350 Isat ( mA ) typ. 1800 1600 1400 1150 970 700 620 500 380 300 3)﹒ Inductance Test Freq.：100KHz / 0.1V 4)﹒ Isat base on △ L / L0A=35% typ. 5)﹒ Irms base on Temp. rise 40℃ typ. □□□ ":Reference code ： Packaging Information... A ：Bulk Inductance VS. DC Current curve 100 470 Inductance(μH) 10 100 4R7 2R2 1 0 0 1 10 DC Current(A) AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 3 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SH3011□□□□2□-□□□ Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape 2.0±0.5 B A ∮C ∮C N G D Embossed carrier ※Carrier tape width : D P:8 m/m End 4 m/m Start 100 100 100 100 Leader no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07 - 12 A 178 B 21±0.8 C 13 D 12 G 14 +0 N 50 -0 Unit:m/m T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SH3011 Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) Outer : Carton G.W. (Kg) Size (cm) 1,200 108 07 - 12 48,000 5.3 42 x 41 x 24 AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 4 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SH3011□□□□2□-□□□ Ⅶ﹒DWGING NUMBER EXPRESSION： S H 3 0 1 1 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2： Package Information Code A B Inner package T.B.D. T / R ( Reel package ) Inner package Q'TY T.B.D. 1,200 pcs Remark AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 5 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SH3011□□□□2□-□□□ Ⅷ﹒RELIABILITY TEST： Test item Specification More than 90% of the terminal electrode Shall be covered With fresh solder. Test condition Preheat : 150±25℃ for 60 seconds S older : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 4±1 seconds Solderability Thermal shock test ( Temp. cycle ) Inductance shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -25±2 ℃ 30 minutes 85±2 ℃ 30 minutes Humidity Resistance test Temperature : 40±2℃ Humidity : 90 ~ 95% Applied current : Per spec. Time : 500 hours High temp. Resistance test Temperature : 105±2℃ Applied current : Per spec. Time : 500 hours AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME PAGE: 6 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. ABC'S ITEM NO. SH3011□□□□2□-□□□ Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW 287806002 Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane BC Coat Typ ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 ANSI Type Temp Class 220 130 200 180 200 ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 Page 1 of 2 A not-for-profit organization dedicated to public safety and committed to quality service SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mtl Dsg Mark Dsg ____ ____ ____ ____ ____ ____ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane BC Coat Typ Polyamide ____ ____ ____ Nylon Polyamide OC MW80C MW2-C ___ MW75C MW28-C MW28-C ANSI Type Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 AR-001A