SH3018101YL

SPECIFICATION FOR APPROVAL R EF : 20080801-A PROD. NAME PAGE: 1 ABC'S DWG NO. ABC'S ITEM NO. SH3018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅰ﹒CONFIGURATION & DIMENSIONS： A A B C D E G H I R : : : : : : : : : 3.80±0.30 3.80±0.30 1.65±0.15 1.30 typ. 1.20 typ. 1.10 ref. 4.30 ref. 1.60 ref. 1.30 ref. H D I m/m m/m m/m m/m m/m m/m m/m m/m m/m 6R8 C B R LCR Meter a c D ( PCB Pattern suggestion ) Ⅱ﹒SCHEMATIC DIAGRAM： Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core b﹒Core：Ferrite RI core c﹒Wire ：Enamelled copper wire (class F & H) d﹒Adhesive ：Epoxy resin e﹒Terminal：Ag/Ni/Sn f﹒Remark：Products comply with RoHS' requirements I b d Peak Temp： 260 ℃ m ax. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. Temperature Rising Area +4.0℃ / sec max. Preheat Area 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area +2.0 ~ 4.0℃ / sec max. G e Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 260℃ 50sec max. 230℃ 70sec max. E 250 T e m p e ra t u r e ( ℃ ) Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：30℃ max. b﹒Storage temp.：-40℃ ----+125℃ c﹒Operating temp.：-25℃----+105℃ d﹒Resistance to solder heat：260℃.10 secs. 200 150 100 50 0 50 100 150 Time ( seconds ) 200 250 AR-001A SPECIFICATION FOR APPROVAL REF : 20080801-A PROD. NAME PAGE: 2 ABC'S DWG NO. ABC'S ITEM NO. SH3018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅴ﹒ ELECTRICAL CHARACTERISTICS： Inductance ( μH ) 1.5 ±30％ 2.5 ±30％ 3.6 ±30％ 4.7 ±30％ 6.8 ±30％ 10.0 ±30％ 15.0 ±30％ 22.0 ±30％ 33.0 ±30％ 47.0 ±30％ 68.0 ±30％ 100.0 ±30％ SRF (MHz) typ. 118 79 79 61 46 39 31 29 24 21 13 10 RDC (mΩ) max. 47 58 85 105 156 205 285 450 660 1000 1450 2400 typ. 35 45 65 85 125 165 230 360 545 800 1200 2050 Irms (mA) max. 1750 1450 1380 1200 850 740 620 510 420 390 320 250 Isat (mA) typ. 1550 1250 1100 900 750 560 450 360 320 250 220 180 DWG No. SH30181R5YL□-□□□ SH30182R5YL□-□□□ SH30183R6YL□-□□□ SH30184R7YL□-□□□ SH30186R8YL□-□□□ SH3018100YL□-□□□ SH3018150YL□-□□□ SH3018220YL□-□□□ SH3018330YL□-□□□ SH3018470YL□-□□□ SH3018680YL□-□□□ SH3018101YL□-□□□ 1). 2)."- □□□ ":Reference code ：Packaging Information… A：Bulk B：Taping Reel 3). Inductance Test Freq. ：100KHz /0.1V 4). Irms base on Temp. rise 30℃ max. 5). Isat base on △L/L0A＝35％ typ. @ Inductance VS. DC Superposition Characteristics 10 3 10 Inductance ( uH ) 2 101 330 10 1 150 4R7 1R5 10 0 10-1 10-2 10-1 100 DC Current ( A ) 101 AR-001A SPECIFICATION FOR APPROVAL REF : 20080801-A PROD. NAME PAGE: 3 ABC'S DWG NO. ABC'S ITEM NO. SH3018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover tape 2.0±0.5 A B ∮C ∮C N G D Embossed carrier ※Carrier tape width : D P:8 m/m End 4 m/m Start 6R8 6R8 6R8 6R8 Leadr no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07 - 12 A 178 B 21±0.8 C 13 D 12 G 14 +0 N 50 -0 Unit:m/m T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SH3018 Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) Outer : Carton G.W. (Kg) Size (cm) 1,000 150 07 - 12 40,000 8.50 42 x 41 x 24 AR-001A SPECIFICATION FOR APPROVAL REF : 20080801-A PROD. NAME PAGE: 4 ABC'S DWG NO. ABC'S ITEM NO. SH3018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅷ﹒DWGING NUMBER EXPRESSION： S H 3 0 1 8 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code A B C T.B.D Inner package Inner package Q'TY T.B.D 1,000 pcs 1,000 pcs Remark T /R (Reel package) T /R (Reel package) Hot-press Type AR-001A SPECIFICATION FOR APPROVAL REF : 20080801-A PROD. NAME PAGE: 5 ABC'S DWG NO. ABC'S ITEM NO. SH3018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅷ ﹒RELIABILITY TEST： Test item Specification Test condition Preheat : 155℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Solderability More than 95% of the terminal electrode Shall be covered With fresh solder. Thermal shock test ( Temp. cycle ) Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -25 ℃ 30 minutes +105 ℃ 30 minutes Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A SPECIFICATION FOR APPROVAL REF : 20080801-A PROD. NAME PAGE: 6 ABC'S DWG NO. ABC'S ITEM NO. SH3018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅸ ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW 287806002 Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ Coat Typ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane Page 1 of 2 ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC ANSI Type MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 Temp Class 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Mtl Dsg SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mark Dsg ____ ____ ____ ____ ____ ____ BC Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Coat Typ OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type MW80C MW2-C ___ MW75C MW28-C MW28-C Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2⁄ E174837 September 8 , 2000 AR-001A SPECIFICATION FOR APPROVAL REF : 20080801-A PROD. NAME PAGE: 7 ABC'S DWG NO. ABC'S ITEM NO. SH3018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR OBMW2 Magnet Wire-Comporent October 06, 2005 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD JALAN DAMAI SATU JANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 180 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Polysol P155p Mark Dsg E180 A200 PN155 P155, G155 Pg155 Pp155,Gp155 P160 P180,G180 P170 or G170 PN180 P155p BC Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ____ ANSI Typ MW-77 MW-74 MW-80, MW-28 MW-79, MW-75 MW-75 MW-79 MW-79 MW-82 MW-79 MW-79 MW-83 MW-79 Temp Class 180 200 155, 130 155, 130 130 155 155 180 155 155 180 155 Marking ：Company name, material designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A