SU4011100YL

SPECIFICATION FOR APPROVAL REF : 20080804-B PROD. NAME PAGE: 1 ABC'S DWG NO. ABC'S ITEM NO. SU4011□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅰ﹒CONFIGURATION & DIMENSIONS： A : 4.30±0.20 B m/m m/m m/m m/m m/m m/m m/m m/m m/m m/m B : 4.50±0.20 C : 1.10±0.15 D : 1.50 typ E : 0.50 typ F : 3.30 typ G : 1.70 ref H : 5.30 ref I : 1.00 ref J : 3.30 ref 100 Ⅱ﹒SCHEMATIC DIAGRAM： ( PCB Pattern suggestion ) I a c b d Ⅲ﹒MATERIALS： a﹒Core： Ferrite DR core b﹒Core：Ferrite RI core c﹒Wire ：Enamelled copper wire (class F & H) d﹒Adhesive ：Epoxy resin e﹒Terminal： Ag/Ni/Sn f﹒Remark： Products comply with RoHS' requirements 250 T empe ratu re ( ℃ ) e Peak Temp： 260 ℃ max. Max time above 230℃ ： 50sec max. Max time above 200℃ ： 70sec max. Temperature Rising Area +4.0℃ / sec max. Preheat Area 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. Peak Temperature: 260℃ 5 0sec max. 230℃ Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：30℃ typ. b﹒Rated current： Base on temp. rise & △L / L0A=35% typ. c﹒Storage temp.：-40℃ ----+125℃ d﹒Operating temp.：-40℃----+105℃ e﹒Resistance to solder heat：260℃.10 secs. AR-001A 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL 20080804-B R EF : 20070329-A PROD. NAME PAGE: 2 ABC'S DWG NO. ABC'S ITEM NO. SU4011 □□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅴ﹒ ELECTRICAL CHARACTERISTICS： Inductance ( μH ) 3.0 ± 30 ％ 4.7 ± 30 ％ 6.8 ± 30 ％ 10.0 ± 30 ％ 15.0 ± 30 ％ 22.0 ± 30 ％ Q ref. 8.0 8.0 8.0 16.0 12.0 12.0 Test Freq. ( Hz ) L Q 100K 7.96M 100K 7.96M 100K 7.96M 100K 2.52M 100K 100K 2.52M 2.52M SRF RDC Irms Isat ( MHz ) ( mA ) ( mA ) ( mΩ ) typ. max. typ. typ. typ. 70 100 150 230 350 420 92 130 230 300 460 680 95 70 54 40 34 22 1700 1250 1050 820 650 580 1150 940 760 610 480 420 DWG No. SU40113R0YL□-□□□ SU40114R7YL□-□□□ SU40116R8YL□-□□□ SU4011100YL□-□□□ SU4011150YL□-□□□ SU4011220YL□-□□□ 1)﹒ 2)﹒"":Reference code 3)﹒ Inductance Test Freq.：100KHz / 0.1V 4)﹒ Isat base on △ L / L0A=35% typ. 5)﹒ Irms base on Temp. rise 30 ℃ typ. □□□ ： Packaging Information... A ：Bulk B ：Taping Reel @ Inductance VS. DC Current Curve 10 2 7 5 3 2 10 1 7 5 3 2 10 0 7 5 3 2 10 -1 10 -2 220 100 6R8 3R0 Induct ance（uH） 2 3 5 7 10 -1 2 3 5 7 10 0 2 3 5 7 10 1 DC Current (A) AR-001A SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. NAME PAGE: 3 ABC'S DWG NO. ABC'S ITEM NO. SU4011□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover tape 2.0 ±0.5 A N ∮C ∮C B G D Embossed carrier ※ Carrier tape width : D P:8 m/m End 4 m/m Stary 100 100 100 100 Leadr no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07 - 12 A 178 B 21±0.8 C 13 D 12 G 14 +0 N 50 -0 Unit:m/m T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) Outer : Carton SU4011 1,500 180 07 - 12 60,000 8.00 42 x 41 x 24 AR-001A SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. NAME PAGE: 4 ABC'S DWG NO. ABC'S ITEM NO. SU4011 □□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅶ﹒DWGING NUMBER EXPRESSION： S U 4 0 1 1 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1： Product Classification L ：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code A B T.B.D. T / R ( Reel package ) Inner package Inner package Q'TY T.B.D. 1,500 pcs Remark AR-001A SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. N AME PAGE: 5 ABC'S DWG NO. ABC'S ITEM NO. SU4011□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅷ﹒RELIABILITY TEST： Test item Specification Test condition Solderability More than 95% of the terminal electrode Shall be covered With fresh solder. Preheat : 155 ℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Thermal shock test ( Temp. cycle ) Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -40 ℃ 30 minutes +105 ℃ 30 minutes Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. N AME PAGE: 6 ABC'S DWG NO. ABC'S ITEM NO. SU4011 □□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Comporent August 27, 1999 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 160 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Mark Dsg E180 A200 PN155 P155 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 BC Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ANSI Typ MW-77 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ Temp Class 180 200 155, 100 155, 130 130 155 155 155 156 180 Marking：Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A SPECIFICATION FOR APPROVAL REF :20080804-B PROD. NAME PAGE: 7 ABC'S DWG NO. ABC'S ITEM NO. SU4011□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR OBMW2 Magnet Wire-Comporent August 27, 1999 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 160 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Mark Dsg E180 A200 PN155 P155 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 BC Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ANSI Typ MW-77 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ Temp Class 180 200 155, 100 155, 130 130 155 155 155 156 180 Marking ：Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A