SU4018150YL

SPECIFICATION FOR APPROVAL R EF :20080804-A PROD. NAME PAGE: 1 ABC'S DWG NO. ABC'S ITEM NO. SU4018□□□□L □-□□□ SHIELDED SMD POWER INDUCTOR Ⅰ﹒CONFIGURATION & DIMENSIONS： A : 4.30±0.20 B : 4.50±0.20 B m/m m/m m/m m/m m/m m/m m/m m/m m/m m/m C : 1.80±0.30 D : 1.50 typ E : 0.50 typ F : 3.30 typ G : 1.70 ref H : 5.30 ref I : 1.00 ref J : 3.30 ref 100 Ⅱ﹒SCHEMATIC DIAGRAM： ( PCB Pattern suggestion ) I a c b d Ⅲ﹒MATERIALS： a﹒ Core：Ferrite DR core b﹒ Core： Ferrite RI core c﹒ Wire ： Enamelled copper wire (class F & H) d﹒ Adhesive ：Epoxy resin e﹒Terminal： Ag/Ni/Sn f﹒ Remark ：Products comply with RoHS' requirements 250 Tem p eratu re ( ℃ ) e Peak Temp： 260 ℃ m ax. Max time above 230℃ ： 50sec max. Max time above 200℃ ： 70sec max. Temperature Rising Area +4.0 ℃ / sec max. Preheat Area 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area +2.0 ~ 4.0℃ / sec max. Forced Coolin g Area -(1 .0 ~ 5 .0 )℃ / sec max. Peak Temperature: 260℃ 230℃ Ⅳ﹒GENERAL SPECIFICATION： a﹒ Temp. rise ：30℃ typ. b﹒ Rated current： Base on temp. rise & △L / L0A=35% typ. c﹒ Storage temp.： -40℃ ----+125℃ d﹒ Operating temp.：-40℃----+105℃ e﹒ Resistance to solder heat：260℃.10 secs. AR-001A 5 0sec max. 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : 20080804-A PAGE: 2 ABC'S DWG NO. ABC'S ITEM NO. SU4018□□□□L□-□□□ PROD. NAME SHIELDED SMD POWER INDUCTOR Ⅴ﹒ ELECTRICAL CHARACTERISTICS： DWG No. SU40181R2YL □-□□□ SU40183R0YL □-□□□ SU40184R7YL □-□□□ SU40186R8YL □-□□□ SU4018100YL□-□□□ SU4018150YL□-□□□ SU4018220YL□-□□□ SU4018330YL□-□□□ SU4018470YL□-□□□ SU4018680YL□-□□□ SU4018101YL□-□□□ 1)﹒ Inductance ( μH ) 1.20 3.00 4.70 6.80 10.00 15.00 22.00 33.00 47.00 68.00 100.0 ±30% ±30% ±30% ±30% ±30% ±30% ±30% ±30% ±30% ±30% ±30% Q ref. 10 10 10 10 20 24 26 22 24 22 60 Test Freq. RDC SRF ( Hz ) ( mΩ ) ( MHz ) typ. max. typ. L Q 100 K 7.96 M 30 40 120 100 K 7.96 M 45 60 80 58 78 60 100 K 7.96 M 80 105 45 100 K 7.96 M 30 100 K 2.52 M 117 160 26 100 K 2.52 M 175 240 20 100 K 2.52 M 255 350 18 100 K 2.52 M 310 400 14 100 K 2.52 M 510 660 10 100 K 2.52 M 750 980 796 K 1170 1500 100 K 6 B ：Taping Reel Irms ( mA ) typ. 2700 2050 1800 1500 1200 900 800 650 550 480 320 Isat ( mA ) typ. 2200 1500 1300 1050 800 600 500 450 400 330 255 2)﹒."":Reference code 3)﹒Inductance Test Freq.：100KHz / 0.1V 4)﹒Isat base on △L / L0A=35% typ. 5)﹒Irms base on Temp. rise 30℃ typ. 10 2 7 5 3 2 10 1 7 5 3 2 10 0 7 5 3 2 10 -1 10 -2 □□□ ： Packaging Information... A ：Bulk @ Inductance VS. DC Current Curve 101 Inductance（uH） 100 1R0 2 3 5 7 10 -1 2 3 5 7 10 0 2 3 5 7 10 1 DC Current (A) AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 3 ABC'S DWG NO. ABC'S ITEM NO. SU4018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover tape 2.0±0.5 A B N ∮C ∮C G D Embossed carrier ※Carrier tape width : D P:8 m/m End 4 m/m Stary 100 100 100 100 Leadr no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07 - 12 A 178 B 21±0.8 C 13 D 12 G 14 +0 N 50 -0 Unit:m/m T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) Outer : Carton SU4018 1,000 180 07 - 12 40,000 8.00 42 x 41 x 24 AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PAGE: 4 ABC'S DWG NO. ABC'S ITEM NO. SU4018□□□□L□-□□□ PROD. NAME SHIELDED SMD POWER INDUCTOR Ⅶ﹒DWGING NUMBER EXPRESSION： S U 4 0 1 8 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code A B T.B.D. T / R ( Reel package ) Inner package Inner package Q'TY T.B.D. 1,000 pcs Remark AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PAGE: 5 ABC'S DWG NO. ABC'S ITEM NO. SU4018□□□□L□-□□□ PROD. N AME SHIELDED SMD POWER INDUCTOR Ⅷ﹒RELIABILITY TEST： Test item Specification Test condition Preheat : 155 ℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Solderability More than 95% of the terminal electrode Shall be covered With fresh solder. Thermal shock test ( Temp. cycle ) Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -40 ℃ 30 minutes +105 ℃ 30 minutes Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PAGE: 6 ABC'S DWG NO. ABC'S ITEM NO. SU4018□□□□L□-□□□ PROD. N AME SHIELDED SMD POWER INDUCTOR Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW 287806002 Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane Coat Typ ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC ANSI Type MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 Temp Class 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 Page 1 of 2 A not-for-profit organization dedicated to public safety and committed to quality service Mtl Dsg S FFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mark Dsg ____ ____ ____ ____ ____ _ ___ BC Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Coat Typ OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type MW80C MW2-C ___ MW75C MW28-C MW28-C Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 AR-001A SPECIFICATION FOR APPROVAL REF :20080804-A PROD. NAME PAGE: 7 ABC'S DWG NO. ABC'S ITEM NO. SU4018 □□□□L□-□□□ SHIELDED SMD POWER INDUCTOR OBMW2 Magnet Wire-Comporent August 27, 1999 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 160 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Mark Dsg E180 A200 PN155 P155 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 BC Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ANSI Typ MW-77 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ Temp Class 180 200 155, 100 155, 130 130 155 155 155 156 180 Marking ：Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A