SU5018100YL

SPECIFICATION FOR APPROVAL REF :20080804-A PROD. NAME PAGE: 1 ABC'S DWG NO. ABC'S ITEM NO. SHIELDED SMD POWER INDUCTOR SU5018□□□□L □-□□□ Ⅰ﹒CONFIGURATION & DIMENSIONS： A A B C D E F G H I : : : : : : : : : I F D I 5.20 5.20 1.80 1.70 1.80 3.90 2.00 3.70 1.10 ±0.20 ±0.20 ±0.20 typ. typ. typ. ref. ref. ref. I m/m m/m m/m m/m m/m m/m m/m m/m m/m C H E D I G ( PCB Pattern Suggestion ) Ⅱ﹒SCHEMATIC DIAGRAM： Ⅲ﹒MATERIALS： a﹒Core： Ferrite DR core b ﹒Core： Ferrite RI core c﹒Wire ：Enamelled copper wire (class F & H) d ﹒Adhesive ：Epoxy resin e﹒Terminal：Ag/Ni/Sn f﹒Remark：Products comply with RoHS' requirements LCR Meter a c b e Peak Temp：260℃ max. Max time above 230℃ ： 50sec max. Max time above 200℃ ： 70sec max. Temperature Rising Area +4.0℃ / sec max. Preheat Area 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. P eak Temperature: 260℃ 50sec max. 230℃ G d 70s ec max. Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise ：30 ℃ max. b﹒Rated current： Base on temp. rise & △L / L0A=35% typ. c﹒Storage temp.：-40 ℃ ----+125℃ d﹒Operating temp.：-40℃----+105℃ e﹒Resistance to solder heat：260 ℃.10 secs. Tem pera ture ( ℃ ) 100 B H 250 200 150 100 50 0 50 100 150 Time ( seconds ) 200 250 AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 2 ABC'S DWG NO. ABC'S ITEM NO. SU5018□□□□ L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅴ﹒ ELECTRICAL CHARACTERISTICS： DWG No. SU50181R0YL□-□□□ SU50181R5YL□-□□□ SU50182R2YL□-□□□ SU50183R5YL□-□□□ SU50184R7YL□-□□□ SU50186R8YL□-□□□ SU5018100YL□-□□□ SU5018150YL□-□□□ SU5018220YL□-□□□ SU5018330YL□-□□□ SU5018470YL□-□□□ SU5018680YL□-□□□ Inductance ( μH ) 1.0 ± 30 ％ 1.5 ± 30 ％ 2.2 ± 30 ％ 3.5 ± 30 ％ 4.7 ± 30 ％ 6.8 ± 30 ％ 10.0 ± 30 ％ 15.0 ± 30 ％ 22.0 ± 30 ％ 33.0 ± 30 ％ 47.0 ± 30 ％ 68.0 ± 30 ％ Q ref. 9.0 9.0 10.0 9.0 8.5 7.5 12.0 12.0 12.0 13.0 13.0 12.0 15.0 Test Freq. ( Hz ) L Q 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 7.96M 7.96M 7.96M 7.96M 7.96M 7.96M 2.52M RDC ( mΩ ) typ. max. 12.5 15.5 20.5 32.0 36.0 50.0 65.0 16.5 20.5 27.0 42.0 47.0 65.0 85.0 130.0 210.0 290.0 430.0 620.0 780.0 SRF ( MHz ) typ. 200 160 130 90 80 60 50 40 28 23 18 16 15 Irms ( mA ) max. 2800 2500 2300 2100 2000 1450 1250 950 680 660 540 370 320 Isat ( mA ) typ. 2850 2400 2100 1700 1550 1200 1050 800 650 560 450 360 310 2.52M 100.0 2.52M 160.0 2.52M 220.0 2.52M 330.0 2.52M 480.0 796K 620.0 SU5018101YL□-□□□ 100.0 ± 30 ％ 1)﹒ 2 )﹒ "- □□□":Reference code ： Packaging Information... A ：Bulk B ：Taping Reel 3)﹒Inductance Test Freq.： 100KHz / 0.1V 4)﹒ Isat base on △ L / LOA=35% typ. 5)﹒ Irms base on Temp. rise 30℃ max. 10 5 3 @ Inductance vs. DC Current curve 10 L (uH) 2 101Y 470Y 5 10 5 1 100Y 4R7Y 10 0 -2 10 5 -1 0 10 5 10 DC Current (A) 5 10 1 AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 3 ABC'S DWG NO. ABC'S ITEM NO. SU5018 □□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape 2.0±0.5 A B ∮C ∮C N G D Embossed carrier ※Carrier tape width : D P:8 m/m 4 m/m End Start 100 100 100 100 Leadr no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07 - 12 A 178 B 21±0.8 C 13 D 12 G 14 +0 N 50 -0 Unit:m/m T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SU5018 Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) Outer : Carton G.W. (Kg) Size (cm) 1,000 200 07 - 12 40,000 9.0 42 x 41 x 24 AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 4 ABC'S DWG NO. ABC'S ITEM NO. SU5018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅶ﹒DWGING NUMBER EXPRESSION： S U 5 0 1 8 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1： Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code A B T.B.D. Inner package Inner package Q'TY T.B.D. 1,000 pcs Remark T / R ( Reel package ) AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 5 ABC'S DWG NO. ABC'S ITEM NO. SU5018□□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅷ﹒RELIABILITY TEST： Test item Specification Test condition Preheat : 155℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Solderability More than 95% of the terminal electrode Shall be covered With fresh solder. Thermal shock test ( Temp. cycle ) Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -40 ℃ 30 minutes +105 ℃ 30 minutes Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 6 ABC'S DWG NO. ABC'S ITEM NO. SU5018 □□□□L□-□□□ SHIELDED SMD POWER INDUCTOR Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW E ILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW 287806002 Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ Coat Typ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane Page 1 of 2 ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC ANSI Type MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 Temp Class 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Mtl Dsg SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mark Dsg ____ ____ ____ ____ ____ ____ Coat Typ BC Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type MW80C MW2-C ___ MW75C MW28-C MW28-C Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 Page 2 of 2 OBMW2 ⁄E174837 September 8 , 2000 AR-001A REF :20080804-A PROD. NAME PAGE: 7 ABC'S DWG NO. ABC'S ITEM NO. SHIELDED SMD POWER INDUCTOR SU5018□□□□L□-□□□ OBMW2 Magnet Wire-Comporent August 27, 1999 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 160 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Mark Dsg E180 A200 PN155 P155 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 BC Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ANSI Typ MW-77 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ Temp Class 180 2 00 155, 100 155, 130 130 155 155 155 156 180 Marking ： Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A