SU60132R2YF

SPECIFICATION FOR APPROVAL REF :20080804-A PROD. NAME PAGE: 1 ABC'S DWG NO. ABC'S ITEM NO. SU6013 □□□□F□-□□□ SHIELDED SMD POWER INDUCTOR Ⅰ﹒CONFIGURATION & DIMENSIONS： ±0.30 ±0.30 ±0.20 typ typ typ ref ref ref A Marking White B C A B C D E F G H I I H I : : : : : : : : : 6.20 6.50 1.40 2.15 2.20 4.90 2.40 4.90 1.10 m/m m/m m/m m/m m/m m/m m/m m/m m/m D I H D E I G Ⅱ . SCHEMATIC DIAGRAM： ( PCB Pattern suggestion ) Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core b ﹒Core：Ferrite RI core c﹒Wire ：Enamelled copper wire (class F & H) d ﹒Adhesive ：Epoxy resin e﹒Terminal：Ag/Ni/Sn f﹒Remark：Products comply with RoHS' requirements 250 G a﹒Temp. rise ：40℃ typ. b ﹒Rated current： Base on temp. rise & △L / L0A=35% typ. c﹒Storage temp.：-40℃ ----+125℃ d ﹒Operating temp. ：-40 ℃----+105℃ e﹒Resistance to solder heat：260 ℃.10 secs. AR-001A Temp erat u re ( ℃ ) Ⅳ﹒GENERAL SPECIFICATION： 100 F e Temperature Rising Area +4.0℃ / sec max. or a c b d Peak Temp： 260 ℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. Preheat Area 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. Peak Temperature: 260℃ 50sec max. 230℃ 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 2 ABC'S DWG NO. ABC'S ITEM NO. SHIELDED SMD POWER INDUCTOR SU6013□□□□F□-□□□ Ⅴ﹒ ELECTRICAL CHARACTERISTICS： DWG No. SU60131R0YF□ -□□□ SU60131R5YF□ -□□□ SU60132R2YF□ -□□□ SU60133R3YF□ -□□□ SU60134R2YF□ -□□□ SU60136R4YF□ -□□□ SU6013100YF□ -□□□ SU6013150YF□ -□□□ SU6013220YF□ -□□□ SU6013330YF□ -□□□ SU6013470YF□ -□□□ SU6013680YF□ -□□□ 1)﹒ 2)."- Inductance ( μH ) 1.0±30% 1.5±30% 2.2±30% 3.3±30% 4.2±30% 6.4±30% 10.0±30% 15.0±30% 22.0±30% 33.0±30% 47.0±30% 68.0±30% Q ref. 12 10 10 10 10 10 14 12 12 10 10 10 Test Freq. ( Hz ) L Q 100K 7.96M 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 100K 7.96M 7.96M 7.96M 7.96M 7.96M 2.52M 2.52M 2.52M 2.52M 2.52M 2.52M SRF RDC ( MHz ) ( mΩ ) typ. max. typ. 28 36 100 32 40 45 58 85 132 180 260 400 540 720 40 50 60 75 110 165 235 325 500 675 900 90 80 70 55 45 35 26 22 18 14 10 Irms ( mA ) typ. 3200 3000 2500 2350 2100 1700 1400 1100 950 780 660 600 Isat ( mA ) typ. 2900 2400 2100 1750 1500 1300 1000 800 720 580 500 400 3)﹒Inductance Test Freq.：100KHz / 0.1V 4)﹒Isat base on △L / L0A=35% typ. 5)﹒Irms base on Temp. rise 40℃ typ. @ Inductance VS. DC Current Curve 10 2 7 5 3 2 10 1 7 5 3 2 10 0 7 5 3 2 10 -1 10 -2 680 □□□":Reference code ：Packaging Information... A ：Bulk B ：Taping Reel Inductance（uH） 100 1R0 2 3 5 7 10 -1 2 3 5 7 10 0 2 3 5 7 10 1 DC Current (A) AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 3 ABC'S DWG NO. ABC'S ITEM NO. SHIELDED SMD POWER INDUCTOR SU6013□□□□F□- □□□ Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape 2.0±0.5 A B ∮C ∮C N G D E mbossed carrier ※Carrier tape width : D P:8.0m/m End 10 0 10 0 10 0 10 0 10 0 10 0 4m/m Start Leader no component 200 m/m min. Components User direction of feed Trailer no component 400 m/m min. ( 2 ) Dimensions Style 07 - 12 A 178 B 21±0.8 C 13±0.5 D 12 G 14 +0 N 50 -0 Unit:m/m T 18.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SU6013 Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) Outer : Carton G.W. (Kg) Size (cm) 1000 230 07 - 12 40,000 8.5 42 x 41 x 24 AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 4 ABC'S DWG NO. ABC'S ITEM NO. SU6013□□□□F□-□□□ SHIELDED SMD POWER INDUCTOR Ⅶ﹒DWGING NUMBER EXPRESSION： S U 6 0 1 3 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification F：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code A B T.B.D. T / R ( Reel package ) Inner package Inner package Q'TY T.B.D. 1000 pcs Remark AR-001A SPECIFICATION FOR APPROVAL REF : 20080804-A PROD. NAME PAGE: 5 ABC'S DWG NO. ABC'S ITEM NO. SHIELDED SMD POWER INDUCTOR SU6013□□□□F□-□□□ Ⅷ﹒RELIABILITY TEST： Test item Specification Test condition Preheat : 155℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Solderability More than 95% of the terminal electrode Shall be covered With fresh solder. Thermal shock test ( Temp. cycle ) Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes Room temp. 15 minutes Total : 50 cycles -40 ℃ 30 minutes +105 ℃ 30 minutes Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A SPECIFICATION FOR APPROVAL REF : PROD. NAME 20080804-A PAGE: 6 ABC'S DWG NO. ABC'S ITEM NO. SHIELDED SMD POWER INDUCTOR SU6013□□□□F□-□□□ Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW E ILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ S FFW 287806002 Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Modified Polyester Polyurethane Coat Typ ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ Nylon ____ ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ OC ANSI Type MW81-C MW75C MW35C ___ ___ ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ MW26C MW79 Temp Class 220 130 200 180 200 220 200 155 155 130 155 155 155 180 155 155 155 180 180 155 155 Page 1 of 2 A not-for-profit organization dedicated to public safety and comm itted to quality service Mtl Dsg SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 Mark Dsg ____ ____ ____ ____ ____ ____ BC Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Coat Typ OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type MW80C MW2-C ___ MW75C MW28-C MW28-C Temp Class 155 105 130 130 130 130 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks or 榮星電線 , material designation or marked designation on packaed or reel, and Recognized Component Mark. See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 2 87806002 Page 2 of 2 OBMW2 ⁄E174837 September 8 , 2000 AR-001A SPECIFICATION FOR APPROVAL REF :20080804-A PROD. NAME PAGE: 7 ABC'S DWG NO. ABC'S ITEM NO. SU6013 □□□□F□-□□□ SHIELDED SMD POWER INDUCTOR OBMW2 Magnet Wire-Comporent August 27, 1999 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 160 Amldester 200 Polysol-N 155 Polysol 155 Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Mark Dsg E180 A200 PN155 P155 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 BC Polyesterimide (solderable) Polyesterimide Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ANSI Typ MW-77 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ Temp Class 180 200 155, 100 155, 130 130 155 155 155 156 180 Marking：Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A