ABLS-24.000MHZ-D-R60-1-W-T

SOURCE CONTROL DRAWING OFFICIAL SPECIFICATION HC/49US (AT49) SMD Low Profile Crystal Item : 565-2400-001 ABLS-24.000MHZ-D-R60-1-W-T EMBER CORP P/N ABRACON P/N : Customer's Approval Please return this copy as a certification of your approval. Approved by: Date : PROPRIETARY NOTICE These documents, and the contained information herein, are proprietary and are not to be reproduced, used or disclosed to others for manufacture or for any other purpose, except as specifically authorized, in writing, by Abracon Corporation. WARNING: ESD SENSITIVE PRODUCT REV. ECO - - Initial release ABRACON ABRACON CORPORATION Headquarters 30332 Esperanza, Rancho Santa Margarita California, The USA. Tel : 949-546-8000 Internal Use Only Fax: 949-546-8001 500205 500041 500450 500210 500710 REVISION HISTORY DESCRIPTION DATE APP'D 1/22/2007 LL TITLE ABLS-24.000MHZ-D-R60-1-W-T HC/49US (AT49) SMD Low Profile Crystal DRAWING NO. CORPORATION The Power Of Linking Together PREP. LL CKD CB DATE 1/22/2007 DATE 1/22/2007 ENGR. HU APP'D JE DATE SCALE 1/22/2007 None DATE PAGE 1/22/2007 452489 OF 1 7 REV. - ABRACON CORPORATION Drawing No. : 452489 Rev. - The Power Of Linking Together 1.0 SCOPE This specification describes a 24.000MHz HC/49US SMD crystal. 2.0 ELECTRICAL SPECIFICATIONS Abracon P/N: Frequency: Operation mode: Operating temperature: Storage temperature: Frequency tolerance: Frequency stability over the operating temperature (Ref to +25° C): Equivalent series resistance (max.): Shunt capacitance C0: Load capacitance CL: Drive level: Aging @ 25° C per a year : Insulation resistance: 3.0 SPECIAL REQUIREMENT This product is RoHS compliant and Pb-free. ABLS-24.000MHZ-D-R60-1-W-T 24.000MHz Fundamental, AT-strip - 40°C to + 85°C - 55°C to + 125° C ± 10 ppm max. ± 25 ppm max. 60ohms max. 7.0pF max 18.0+/-1.0pF 1mW max,. 100uW Typical ± 5 ppm max. / year 500 Mohms min. at 100 Vdc ± 15 Vdc Page 2 of 7 ABRACON CORPORATION Drawing No. : 452489 Rev. - Page 3 of 7 The Power Of Linking Together 4.0 Marking 240: Frequency 24.000MHz A240ZYX Traceability Code (Internal) Year : e.g. 7 for 2007 Month : A to Z Month January February March April May June July August September October November December 4.1 Marking Method : Laser Marking Code A B C D E F G H I J K L ABRACON CORPORATION Drawing No. : 452489 Rev. - Page 4 of 7 The Power Of Linking Together 5.0 Outline dimensions Dimension : Inches (mm) TOLERANCES: UNLESS OTHERWISE SPECIFIED: .X: ± 0.1 (0.25) .XX: ± 0.01 (0.025) .XXX: ± 0.005 (0.013) ABRACON CORPORATION Drawing No. : 452489 Rev. - Page 5 of 7 The Power Of Linking Together 6.0 Reliability Test No. Test Items 1 Temperature Cycling: 2 Thermal Shock: 3 Vibration: 4 Drop Test: 5 Humidity: 6 Fine Leak Test: 7 Gross Leak Test: 8 Solderability: 9 Lead Bend 6.1 Reflow Profile Test Conditions The component shall remain within the electrical specification (± 5 ppm max) after 3 cycles of high and low temperature testing (-40°C to +85°C) for 2 hours max. The component shall remain within the electrical specification after exposure at extreme temperature -40°C to +85°C for 5 minutes for 3 cycles. The component shall remain within the electrical specification after loaded vibration at 10Hz to 55Hz, amplitude 1.5mm, within 1 minute for 2 hours minimum on each axis (X,Y,Z). The component shall remain within the electrical specifications after a natural drop (3X) on a hard wooden board at 75 cm. The component shall remain within the electrical specifications after being kept at a condition of ambient temperature +85°C, 85% RH for 96 hours minimum. Expose samples to 60PSIG Helium gas for 2 hours. Max leak rate 2X10-8atmcc/s. Submerge samples in 100% De-ionized water or Perfluorocarbon at 85°C for at least 1 minute. Check for bubbles. Solderability of terminals shall be kept at more than 95% after dipped in solder flux at 230°C ± 5°C for 5 seconds. The component shall withstand maximum bend of 90°C reference to base for 2 bends. Solder tinning must be 4 microns thick minimum. ABRACON CORPORATION Drawing No. : 452489 Rev. - Page 6 of 7 The Power Of Linking Together 7.0 PACKING T= tape and reel (1,000pcs/reel) Dimension : Inches (mm) TOLERANCES: UNLESS OTHERWISE SPECIFIED: .X: ± 0.1 (0.25) .XX: ± 0.01 (0.025) .XXX: ± 0.005 (0.013) ABRACON CORPORATION Drawing No. : 452489 Rev. - The Power Of Linking Together 8.0 Note (1) The parts are manufactured in accordance with this specification. If other conditions and specifications which are required for this specification, please contact ABRACON for more information. (2) ABRACON will supply the parts in accordance with this specification unless we receive a written request to modify prior to an order placement. (3) In no case shall ABRACON be liable for any product failure from in appropriate handling or operation of the item beyond the scope of this specification. (4) When changing your production process, please notify ABRACON immediately. (5) If you intend to use the product for listed application which may possibly cause to loss of life or assets, please notify ABRACON in advance. (For example, Medical, Aerospace, Aeronautic equipment, Safety control equipment as well as safety related.) (6) All specifications and Marking will be subject to change without notice. (7) See ABRACON website (www.abracon.com) for additional Terms and Conditions. Page 7 of 7