ANFCA-101-2515-A02

Engineering/Process Change Notice ECN/PCN No.: #R0012 For Manufacturer Product Description: NXP IOT RFERENCE DESIGN: FLEXIBLE NFC ANTENNA WITH FERRITE Affected Revision: INITIAL RELEASE Abracon Part Number / Part Series: ANFCA-101-2515-A02 New Revision: ☐ Series ☒ Part Number Application: N/A ☐ Safety ☐ Non-Safety Prior to Change: ACTIVE After Change: PRODUCT EOL - NO LONGER AVAILABLE Cause/Reason for Change: FACTORY EOL Change Plan Effective Date: 7/7/2020 Additional Remarks: Change Declaration: Issued Date: 7/7/2020 Issued By: JUSTIN FAHEY Approval: Approval: Reuben Quintanilla Quality Director Syed Raza Engineering VP Issued Department: MARKETING - PLM Approval: Ying Huang Purchasing Director For Abracon EOL only Last Time Buy (if applicable): NONE Additional Approval: JUSTIN FAHEY – PLM Alternate Part Number / Part Series: NONE Additional Approval: Additional Approval: Customer Approval (If Applicable) Qualification Status: ☐ Approved ☐ Not accepted Note: It is considered approved if there is no feedback from the customer 1 month after ECN/PCN is released. Customer Part Number: Company Name: Customer Project: Company Representative: Customer Remarks: Form #7020 Rev. E Effective: 04/20/2020 Page 1 of 1 Representative Signature: FLEXIBLE NFC ANTENNA WITH FERRITE ANFCA-2515-A02 ANFCA-101-2515-A02 Pb FEATURES • • • • • • 25 x 15 mm RoHS/RoHS II Compliant MSL = MSL-1 APPLICATIONS Ultra thin flexible antenna structure (220+/-46μm) Peel and Stick antenna designs Ferrite sheet backing optimizes magnetic fields Wide operating temperature range -40℃ to +85℃ Matched to leading NFC controller IC’s Customized solutions available • • • • • • • IoT devices NFC payment readers Healthcare ID scanners NFC data loggers transport Ticketing systems Electronic parking payments Industrial data collection L ELECTRICAL CHARACTERISTICS Spec Operating Frequency (MHz) 13.56 Inductance (μH) 1.8±10% RAC (Ω) 4.75±20% Test Condition 1 MHz/500mV Operating Temperature Range -40ºC to + 85ºC EO Item Test equipment: TH2828S. LLC 5101 Hidden Creek Ln Spicewood TX 78669 Phone: 512-371-6159 | Fax: 512-351-8858 For terms and conditions of sales, please visit: www.abracon.com REVISED: 04.25.2018 ABRACON IS ISO9001-2008 CERTIFIED FLEXIBLE NFC ANTENNA WITH FERRITE ANFCA-2515-A02 ANFCA-101-2515-A02 Pb 25 x 15 mm RoHS/RoHS II Compliant MSL = MSL-1 MATCHING CIRCUIT AND REFERENCE VALUES Component Value for reference only (1) Notes L0 560 / 330nH NXP / Broadcom) EMC filter resonance at 15.4MHz（NXP) and 20.6MHz (Broadcom). C0 180pF EMC filter resonance at 15.4MHz (NXP) and 20.6MHz (Broadcom). 33pF L C1 Antenna matching component, to achieve series resonance at 13.56MHz. (Note: Antenna matching component value may need optimization depending upon antenna environment) Antenna matching component, to achieve parallel resonance at 15MHz. (Note: Antenna matching component value may need optimization depending upon antenna environment). 82pF Rq 0 Ohm Damping resistor, the Rq resistor used to lower Q-value if above 35 Ohm, if needed. EO C2 (Includes C2a and C2b values) Note (1) Values can change depending upon drive circuits, design of the antenna and environment. Matching Circuit LLC 5101 Hidden Creek Ln Spicewood TX 78669 Phone: 512-371-6159 | Fax: 512-351-8858 For terms and conditions of sales, please visit: www.abracon.com REVISED: 04.25.2018 ABRACON IS ISO9001-2008 CERTIFIED FLEXIBLE NFC ANTENNA WITH FERRITE ANFCA-101-2515-A02 ANFCA-2515-A02 Pb 25 x 15 mm RoHS/RoHS II Compliant MSL = MSL-1 MATCHING NETWORKS L Several conditions apply when matching: • Environment of the design. • Placement of Antenna o The antenna should be placed as close to the matching network as possible o How close the NFC antenna is placed to other metalwork and other coils within the design. • Antenna design o Optimization of the matching network is likely to be needed and this should be done with the antenna in the desired position. • NFC normally operates from 1 to 4cm between devices. Final optimization of the matching circuit should be com pleted to ensure compliance. • Designers need to consider interoperability with other devices. The antenna and matching network contribute to best interoperability. CONNECTION TO THE PCB EO While soldering thin wires to the pads on the antenna is possible, great care must be taken, (see manual soldering Section 10.1). However it is recommended to make contact to the antenna pads via Pogo Pins. These are soldered onto the product PCB, and interface mechanically via a pressure contact to the pads on the NFC antenna. Volume applications using the NFC antenna should always use Pogo Pins to make the connections. ANTENNA RESPONSE – RETURN LOSS LLC 5101 Hidden Creek Ln Spicewood TX 78669 Phone: 512-371-6159 | Fax: 512-351-8858 For terms and conditions of sales, please visit: www.abracon.com REVISED: 04.25.2018 ABRACON IS ISO9001-2008 CERTIFIED FLEXIBLE NFC ANTENNA WITH FERRITE ANFCA-2515-A02 ANFCA-101-2515-A02 Pb 25 x 15 mm RoHS/RoHS II Compliant MSL = MSL-1 OUTSIDE DIMENSIONS (Dimensions in mm) CONSTRUCTION Construction materials and thickness No 1 2 3 4 5 6 Material Name PET Tape Ferrite Sheet Adhesive Tape FCP Adhesive Tape Release Paper Total Thickness LLC Thickness ( μm) 10+/-3 100+/-5 10+/-3 70+/-30 30+/-5 / 220+/-46 Thickness (in) 0.000393±0.000118 0.00393±0.000196 0.000393±0.000118 0.00275±0.000118 0.00118±0.000196 / 0.00866±0.00181 5101 Hidden Creek Ln Spicewood TX 78669 Phone: 512-371-6159 | Fax: 512-351-8858 For terms and conditions of sales, please visit: www.abracon.com REVISED: 04.25.2018 ABRACON IS ISO9001-2008 CERTIFIED FLEXIBLE NFC ANTENNA WITH FERRITE ANFCA-101-2515-A02 ANFCA-2515-A02 Pb 25 x 15 mm RoHS/RoHS II Compliant MSL = MSL-1 REFLOW PROFILE: Not recommended for reflow soldering. MANUAL SOLDERING Recommended Soldering iron temperature setting: 330°C, 3 seconds max, 3 times max. PACKAGING: 100pcs per polyphene bag / box LLC 5101 Hidden Creek Ln Spicewood TX 78669 Phone: 512-371-6159 | Fax: 512-351-8858 For terms and conditions of sales, please visit: www.abracon.com REVISED: 04.25.2018 ABRACON IS ISO9001-2008 CERTIFIED