AOCJY1_1012

OVEN CONTROLLED CRYSTAL OSCILLATOR AOCJY1 Series FEATURES: • 20.8 x 13.2 x 8.2 mm Leaded- RoHS Compliant Reflow-able Package • AT-Cut, High “Q” resonator based design • Either Sinewave or CMOS RF output • Available with ±500 ppb over -40°C to +75°C operating temperature Range • Tighter Stabilities to ±50.0 ppb over 0°C to +50°C also available • Exceptional long-term Aging of ±3 ppm max. over 10-Year Product Life • Excellent close-in phase noise (-145 dBc/Hz Typical @1k Hz offset; 10MHz carrier) Pb RoHS Compliant 20.8 x 13.2 x 8.2 mm |||||||||||||| | APPLICATIONS: • Cellular Infrastructure • Radar Systems • Test & Measurement Equipment • GPS Tracking with precision hold-over accuracy • WiMax / WLAN STANDARD SPECIFICATIONS: Parameters RF Output Frequency Standard Available Frequencies Waveform Level "1" (Logic High) Level "0" (Logic Low) Load Rise & Fall Time Duty Cycle Waveform Peak Power Output Load Short Term Stability Operable Temperature Range Frequency Stability Options 0º C to +50ºC -20º C to +70ºC -40º C to +75ºC Frequency Stability vs. Supply Voltage (Vdd ± 5%) Warm-Up @ 25 ºC Power Consumption @ turn on Power Consumption Steady State Supply Voltage (Vdd) Aging Yearly 10-Years ABRACON IS ABRACON IS ISO9001:2008 CE R TIFIED CE R TIFIED Minimum Typical Maximum Units Notes Overall Frequency range 10.00 100.00 MHz 10.00, 12.80, 13.00, 26.00, 38.88, 40.00, 100.00 MHz CMOS 0.9*Vdd 0.1*Vdd 15 6.0 45 Sinewave 2.00 50 1x10 -40 -9 Volts Volts pf ns % dBm Ω /second 75 ±50.00 ±200.00 ±500.00 ºC ppb ppb ppb Alan Variance See Stability Options Default Spec. Option “E” Option “F” 55 ±50.00 ±500.00 2.00 1.00 3.13 3.30 3.46 ±500 ±3.00 ppb ppb Watts Watt Volts ppb ppm See Options In < 3-minutes Visit www.abracon.com for Terms & Conditions of Sale Revised: 12.01.10 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com OVEN CONTROLLED CRYSTAL OSCILLATOR AOCJY1 Series STANDARD SPECIFICATIONS - continued. Parameters Supply Voltage Variation Spectral Content Spurious Response Phase Noise (10MHz Carrier) @ 5V @ 10 @ 100 Hz offset Hz offset -90 -120 -145 -150 0. 0 ±5.00 Positive 10 (Vdd/2) 0.5 -40 kΩ Vdd/2 ±10 +100 (Vdd/2) +0.5 Volts % ºC Vdd dBc / Hz dBc / Hz dBc / Hz dBc / Hz Volts ppm Minimum Typical Maximum ±50 -35 Units ppb dBc Notes VDD ± 5% change Pb RoHS Compliant 20.8 x 13.2 x 8.2 mm ||||||||||||||| @ 1,000 Hz offset @ 10,000 Hz offset Electrical Frequency Adjustment Control Voltage Range (Vc) Frequency Pull Range Frequency Pull Slope Control Voltage Port Impedance Center Control Voltage Control Port Linearity Storage Temperature OPTIONS AND PART IDENTIFICATION (Left blank if standard) AOCJY1 Supply Voltage Option Blank 3.30V A 5.00V - MHz - - Temperature Options E -20°C to +70°C F -40°C to +75°C Frequency in MHz Such as; 10.000 MHz 26.000 MHz 100.000 MHz RF Output Options Blank CMOS SW Sinewave ABRACON IS ABRACON IS ISO9001:2008 CE R TIFIED CE R TIFIED Revised: 12.01.10 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com Visit www.abracon.com for Terms & Conditions of Sale OVEN CONTROLLED CRYSTAL OSCILLATOR AOCJY1 Series OUTLINE DIMENSIONS Pb RoHS Compliant 20.8 x 13.2 x 8.2 mm ||||||||||||||| 7.80 Max Pin 1 7 8 14 Function Control Voltage GND Output Power Supply (50) PACKAGING: units per tray REFLOW PROFILE: TS max to TL (Ramp-up Rate) Preheat Temperature Min. (TS Min.) Temperature Typical (T S Typ.) Temperature Max. (TS Max.) Time (tS) Ramp-up rate (TL to Tp ) Time Maintained Above: --Temperature (TL)/Time (TL) Peak Temperature (Tp) Target Peak Temperature (Tp Target) Time within 5°C of actual peak (tp) Ramp-down Rate Tune 25°C to Peak Temperature (t) 3°C/second max. 150°C 175°C 200°C 60 ~ 180 seconds 3°C/second max. 217°C/60 ~ 150 seconds 250°C max. for 10 seconds 250°C +0/-5°C 20 ~ 40 seconds 6°C/second max. 8 minutes max. ATTENTION: Abracon Corporation’s products are COTS – Commercial-Off-The-Shelf products; suitable for Commercial, Industrial and, where designated, Automotive Applications. Abracon’s products are not specifically designed for Military, Aviation, Aerospace, Life-dependant Medical applications or any application requiring high reliability where component failure could result in loss of life and/or property. For applications requiring high reliability and/or presenting an extreme operating environment, written consent and authorization from Abracon Corporation is required. Please contact Abracon Corporation for more information. ABRACON IS ABRACON IS ISO9001:2008 CE R TIFIED CE R TIFIED Visit www.abracon.com for Terms & Conditions of Sale Revised: 12.01.10 30332 Esperanza, Rancho Santa Margarita, California 92688 tel 949-546-8000 | fax 949-546-8001 | www.abracon.com