1N4916A/TR

1N4916 thru • 19.2 VOLT NOMINAL ZENER VOLTAGE + 5% • TEMPERATURE COMPENSATED ZENER REFERENCE DIODES 1N4932A • LOW NOISE • METALLURGICALLY BONDED • DOUBLE PLUG CONSTRUCTION MAXIMUM RATINGS Operating Temperature: -65°C to +175°C Storage Temperature: -65°C to +175°C DC Power Dissipation: 500mW @ +50°C Power Derating: 4 mW / °C above +50°C REVERSE LEAKAGE CURRENT lR = 15 µA @ 25°C & VR = 12Vdc ELECTRICAL CHARACTERISTICS @ 25°C, unless otherwise speci½ed. JEDEC TYPE NUMBER TEST CURRENT l ZT (Note 3) VOLTAGE TEMPERATURE STABILITY ³VZT (Note 2) TEMPERATURE RANGE EFFECTIVE TEMPERATURE COEFFICIENT MAXIMUM DYNAMIC IMPEDANCE ZZT (Note 1) MAXIMUM NOISE DENSITY ND µV √ Hz mA mV °C %/°C OHMS 1N4916 1N4916A 1N4917 1N4917A 0.5 0.5 0.5 0.5 144 298 72 149 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.01 0.01 0.005 0.005 600 600 600 600 1.0 1.0 1.0 1.0 1N4918 1N4918A 1N4919 1N4919A 0.5 0.5 1.0 1.0 29 60 144 298 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.002 0.002 0.01 0.01 600 600 300 300 1.0 1.0 0.5 0.5 1N4920 1N4920A 1N4921 1N4921A 1.0 1.0 1.0 1.0 72 149 29 60 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.005 0.005 0.002 0.002 300 300 300 300 0.5 0.5 0.5 0.5 1N4922 1N4922A 1N4923 1N4923A 2.0 2.0 2.0 2.0 144 298 72 149 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.01 0.01 0.005 0.005 150 150 150 150 0.25 0.25 0.25 0.25 1N4924 1N4924A 1N4925 1N4925A 2.0 2.0 4.0 4.0 29 60 144 298 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.002 0.002 0.01 0.01 150 150 75 75 0.25 0.25 0.22 0.22 DESIGN DATA 1N4926 1N4926A 1N4927 1N4927A 4.0 4.0 4.0 4.0 72 149 29 60 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.005 0.005 0.002 0.002 75 75 75 75 0.22 0.22 0.22 0.22 CASE: Hermetically sealed glass case. DO – 35 outline. 1N4928 1N4928A 1N4929 1N4929A 4.0 4.0 7.5 7.5 14 30 144 298 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.001 0.001 0.01 0.01 75 75 36 36 0.22 0.22 0.20 0.20 1N4930 1N4930A 1N4931 1N4931A 7.5 7.5 7.5 7.5 72 149 29 60 +25 to +100 -55 to +100 +25 to +100 -55 to +100 0.005 0.005 0.002 0.002 36 36 36 36 0.20 0.20 0.20 0.20 1N4932 1N4932A 7.5 7.5 14 30 +25 to +100 -55 to +100 0.001 0.001 36 36 0.20 0.20 FIGURE 1 LEAD MATERIAL: Copper clad steel. LEAD FINISH: Tin / Lead POLARITY: Diode to be operated with the banded (cathode) end positive. MOUNTING POSITION: Any. NOTE 1 Zener impedance is derived by superimposing on lZT A 60Hz rms a.c. current equal to 10% of lZT. NOTE 2 The maximum allowable change observed over the entire temperature range i.e.,the diode voltage will not exceed the speci½ed mV at any discrete temperature between the established limits, per JEDEC standard No.5. NOTE 3 Zener voltage range equals 19.2 volts + 5%. 6 LAKE STREET, LAWRENCE, MASSACHUSETTS 01841 PHONE (978) 620-2600 FAX (978) 689-0803 WEBSITE: http://www.microsemi.com 55 1N4916 thru 1N4932A ZENER IMPEDANCE ZZT (OHMS) 1000 500 200 100 50 20 10 2 4 6 8 10 12 OPERATING CURRENT lZT (mA) FIGURE 2 1N4916—1N4918 1N4919—1N4921 .2 .4 .6 .8 OPERATING CURRENT lZT (mA) 0.5 1.0 1.5 2.0 OPERATING CURRENT lZT (mA) 1N4922—1N4924 +.0015 +.0010 +.0005 0 -.0005 -.0010 -.0015 CHANGE IN TEMPERATURE COEFFICIENT ( %/°C) CHANGE IN TEMPERATURE COEFFICIENT ( %/°C) ZENER IMPEDANCE VS. OPERATING CURRENT 1.0 2.0 3.0 4.0 OPERATING CURRENT lZT (mA) 1N4925—1N4928 1N4929—1N4932 2 3 4 5 6 OPERATING CURRENT lZT (mA) 6 7 8 9 OPERATING CURRENT lZT (mA) +.0015 +.0010 +.0005 0 -.0005 -.0010 -.0015 FIGURE 3 TYPICAL CHANGE OF TEMPERATURE COEFFICIENT WITH CHANGE IN OPERATING CURRENT 56