24AA024H/24LC024H
2K I2C™ Serial EEPROM with Half-Array Write Protect
Device Selection Table
Description:
Part
Number
VCC
Range
Max.
Clock
Temp.
Range
24AA024H
1.7V-5.5V
400 kHz(1)
I
24LC024H
2.5V-5.5V
1 MHz
I, E
Note 1: 100 kHz for VCC < 1.8V
Features:
• Single-Supply with Operation Down to 1.7V
• Low-Power CMOS Technology:
- 400 μA active current, max.
- 1 μA standby current, max.
• Organized as a Single Block of 256 Bytes
(256 x 8)
• 2-Wire Serial Interface Bus, I2C™ Compatible
• Schmitt Trigger Inputs for Noise Suppression
• Output Slope Control to Eliminate Ground Bounce
• 100 kHz and 400 kHz Compatibility
• 1 MHz Compatibility (LC)
• Page Write Buffer for up to 16 Bytes
• Self-Timed Write Cycle (including Auto-Erase)
• Hardware Write Protection for Half Array
(80h-FFh)
• Address Lines Allow up to Eight Devices on Bus
• 1 Million Erase/Write Cycles
• ESD Protection > 4,000V
• Data Retention > 200 Years
• Factory Programming (QTP) Available
• 8-pin PDIP, SOIC, TSSOP, TDFN and MSOP
Packages
• Available for Extended Temperature Ranges:
The Microchip Technology Inc. 24AA024H/24LC024H is
a 2 Kbit Serial Electrically Erasable PROM with
operation down to 1.7V. The device is organized as a
single block of 256 x 8-bit memory with a 2-wire serial
interface. Low-current design permits operation with
maximum standby and active currents of only 1 μA and
400 μA, respectively. The device has a page write
capability for up to 16 bytes of data. Functional address
lines allow the connection of up to eight 24AA024H/
24LC024H devices on the same bus for up to 16 Kbits
of contiguous EEPROM memory. The device is
available in the standard 8-pin PDIP, 8-pin SOIC (150
mil), TSSOP, 2x3 TDFN and MSOP packages.
Block Diagram
A0 A1 A2
I/O
Control
Logic
WP
HV Generator
Memory
Control
Logic
EEPROM
Array
XDEC
SDA SCL
Write-Protect
Circuitry
YDEC
VCC
VSS
Sense Amp.
R/W Control
Package Types
SOIC, TSSOP
PDIP, MSOP
A0
1
8
VCC
A0
1
8
VCC
- Industrial (I):
-40°C to
+85°C
A1
2
7
WP
A1
2
7
WP
- Automotive (E):
-40°C to
+125°C
A2
3
6
SCL
A2
3
6
SCL
VSS
4
5
SDA VSS
4
5
SDA
• Pb-Free and RoHS compliant
TDFN
A0 1
A1 2
A2 3
VSS 4
© 2008 Microchip Technology Inc.
8 VCC
7 WP
6 SCL
5 SDA
DS22102A-page 1
24AA024H/24LC024H
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings (†)
VCC .............................................................................................................................................................................6.5V
All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied ................................................................................................-40°C to +125°C
ESD protection on all pins ......................................................................................................................................................≥ 4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
DC CHARACTERISTICS
Param.
No.
Sym.
Characteristic
Electrical Characteristics:
Industrial (I):
VCC = +1.7V to 5.5V
Automotive (E): VCC = +2.5V to 5.5V
Min.
Max.
Units
TA = -40°C to +85°C
TA = -40°C to +125°C
Conditions
D1
—
A0, A1, A2, SCL, SDA
and WP pins:
—
—
—
—
D2
VIH
High-level input voltage
0.7 VCC
—
V
—
D3
VIL
Low-level input voltage
—
0.3 VCC
V
—
D4
VHYS
Hysteresis of Schmitt
Trigger inputs
(SDA, SCL pins)
0.05 VCC
—
V
(Note)
D5
VOL
Low-level output voltage
—
0.40
V
IOL = 3.0 ma @ VCC = 4.5V
IOL = 2.1 ma @ VCC = 2.5V
D6
ILI
Input leakage current
—
±1
μA
VIN = VSS or VCC, WP = VSS
D7
ILO
Output leakage current
—
±1
μA
VOUT = VSS or VCC
D8
CIN,
COUT
Pin capacitance
(all inputs/outputs)
—
10
pF
VCC = 5.0V (Note)
TA = 25°C, f = 1 MHz
D9
ICC Read Operating current
—
400
μA
VCC = 5.5V, SCL = 400 kHz
—
3
mA
VCC = 5.5V
—
1
μA
VCC = 5.5V, SCL = SDA = VCC
WP = VSS, A0, A1, A2 = VSS
ICC
D10
Note:
Write
ICCS
Standby current
This parameter is periodically sampled and not 100% tested.
DS22102A-page 2
© 2008 Microchip Technology Inc.
24AA024H/24LC024H
TABLE 1-2:
AC CHARACTERISTICS
Electrical Characteristics:
AC CHARACTERISTICS
Param.
No.
Symbol
Industrial (I):
Automotive (E):
Characteristic
VCC = +1.7V to 5.5V
VCC = +2.5V to 5.5V
Min.
Max.
Units
TA = -40°C to +85°C
TA = -40°C to +125°C
Conditions
1
FCLK
Clock frequency
—
—
—
100
400
1000
kHz
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
2
THIGH
Clock high time
4000
600
500
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
3
TLOW
Clock low time
4700
1300
500
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
4
TR
SDA and SCL rise time (Note 1)
—
—
—
1000
300
300
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
5
TF
SDA and SCL fall time (Note 1)
—
—
—
1000
300
300
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
6
THD:STA
Start condition hold time
4000
600
250
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
7
TSU:STA
Start condition setup time
4700
600
250
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
8
THD:DAT
Data input hold time
0
—
ns
(Note 2)
9
TSU:DAT
Data input setup time
250
100
100
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
10
TSU:STO
Stop condition setup time
4000
600
250
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
11
TSU:WP
WP setup time
4000
600
600
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
12
THD:WP
WP hold time
4700
600
600
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
13
TAA
Output valid from clock (Note 2)
—
—
—
3500
900
400
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
14
TBUF
Bus free time: Time the bus must be
free before a new transmission can
start
1300
4700
4700
—
—
—
ns
1.7V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 5.5V
2.5V ≤ VCC ≤ 5.5V (24LC024H)
16
TSP
Input filter spike suppression
(SDA and SCL pins)
—
50
ns
24AA024H
(Note 1 and Note 3)
17
TWC
Write cycle time (byte or page)
—
5
ms
18
—
Endurance
1M
—
cycles
Note
1:
2:
3:
4:
—
25°C, VCC = 5.5V, Block mode
(Note 4)
Not 100% tested. CB = total capacitance of one bus line in pF.
As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the
falling edge of SCL to avoid unintended generation of Start or Stop conditions.
The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs, which provide improved noise spike suppression. This eliminates the need for a TI specification for standard operation.
This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult
the Total Endurance™ Model which can be obtained from Microchip’s web site at www.microchip.com.
© 2008 Microchip Technology Inc.
DS22102A-page 3
24AA024H/24LC024H
FIGURE 1-1:
BUS TIMING DATA
5
SCL
7
SDA
In
3
4
D4
2
8
10
9
6
16
14
13
SDA
Out
WP
DS22102A-page 4
(protected)
(unprotected)
11
12
© 2008 Microchip Technology Inc.
24AA024H/24LC024H
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
PIN FUNCTION TABLE
8-pin
PDIP
8-pin
SOIC
8-pin
TSSOP
8-pin
MSOP
8-pin
TDFN
A0
1
1
1
1
1
User Configurable Chip Select
A1
2
2
2
2
2
User Configurable Chip Select
A2
3
3
3
3
3
User Configurable Chip Select
VSS
4
4
4
4
4
Ground
Name
Function
SDA
5
5
5
5
5
Serial Data
SCL
6
6
6
6
6
Serial Clock
WP
7
7
7
7
7
Write-Protect Input
VCC
8
8
8
8
8
+1.7V to 5.5V (24AA024H)
+2.5V to 5.5V (24LC024H)
2.1
SDA Serial Data
2.4
WP
This is a bidirectional pin used to transfer addresses
and data into and out of the device. It is an open drain
terminal. Therefore, the SDA bus requires a pull-up
resistor to VCC (typical 10 kΩ for 100 kHz, 2 kΩ for
400 kHz).
WP is the hardware write-protect pin. It must be tied to
VCC or VSS. If tied to VCC, the hardware write protection
is enabled and will protect half of the array (80h-FFh).
If the WP pin is tied to VSS the hardware write
protection is disabled.
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
2.5
2.2
SCL Serial Clock
The SCL input is used to synchronize the data transfer
to and from the device.
2.3
Noise Protection
The 24AA024H/24LC024H employs a VCC threshold
detector circuit that disables the internal erase/write
logic if the VCC is below 1.5 volts at nominal conditions.
The SCL and SDA inputs have Schmitt Trigger and
filter circuits that suppress noise spikes to assure
proper device operation even on a noisy bus.
A0, A1, A2
The A0, A1 and A2 inputs are used by the 24AA024H/
24LC024H for multiple device operations. The levels
on these inputs are compared with the corresponding
bits in the slave address. The chip is selected if the
compare is true.
Up to eight 24AA024H/24LC024H devices may be
connected to the same bus by using different Chip
Select bit combinations. These inputs must be
connected to either VCC or VSS.
In most applications, the chip address inputs A0, A1
and A2 are hard-wired to logic ‘0’ or logic ‘1’. For
applications in which these pins are controlled by a
microcontroller or other programmable device, the chip
address pins must be driven to logic ‘0’ or logic ‘1’
before normal device operation can proceed.
© 2008 Microchip Technology Inc.
DS22102A-page 5
24AA024H/24LC024H
3.0
FUNCTIONAL DESCRIPTION
The 24AA024H/24LC024H supports a bidirectional,
2-wire bus and data transmission protocol. A device
that sends data onto the bus is defined as transmitter,
and a device receiving data as receiver. The bus has
to be controlled by a master device that generates the
Serial Clock (SCL), controls the bus access and
generates the Start and Stop conditions while the
24AA024H/24LC024H works as slave. Both master
and slave can operate as transmitter or receiver, but
the master device determines which mode is
activated.
DS22102A-page 6
© 2008 Microchip Technology Inc.
24AA024H/24LC024H
4.0
BUS CHARACTERISTICS
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
• During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Accordingly, the following bus conditions have been
defined (Figure 4-1).
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device and is,
theoretically, unlimited, though only the last sixteen will
be stored when doing a write operation. When an
overwrite does occur, it will replace data in a first-in
first-out fashion.
4.1
4.5
Bus Not Busy (A)
Each receiving device, when addressed, is required to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this Acknowledge bit.
Both data and clock lines remain high.
4.2
Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3
Note:
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
Data Valid (D)
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
FIGURE 4-1:
SCL
(A)
The 24AA024H/24LC024H does not generate any Acknowledge bits if an internal
programming cycle is in progress.
The device that acknowledges has to pull down the
SDA line during the Acknowledge clock pulse in such a
way that the SDA line is stable low during the high
period of the acknowledge-related clock pulse. Of
course, setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an Acknowledge bit on the last
byte that has been clocked out of the slave. In this case,
the slave must leave the data line high to enable the
master to generate the Stop condition (Figure 4-2).
Stop Data Transfer (C)
4.4
Acknowledge
DATA TRANSFER SEQUENCE ON THE SERIAL BUS CHARACTERISTICS
(B)
(C)
(D)
(C)
(A)
SDA
Start
Condition
FIGURE 4-2:
Address or
Acknowledge
Valid
Stop
Condition
Data
Allowed
to Change
ACKNOWLEDGE TIMING
Acknowledge
Bit
SCL
SDA
1
2
3
4
5
6
7
Data from transmitter
Transmitter must release the SDA line at this point allowing
the Receiver to pull the SDA line low to acknowledge the
previous eight bits of data.
© 2008 Microchip Technology Inc.
8
9
1
2
3
Data from transmitter
Receiver must release the SDA line at this
point so the Transmitter can continue
sending data.
DS22102A-page 7
24AA024H/24LC024H
5.0
DEVICE ADDRESSING
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a four-bit control code; for
the 24AA024H/24LC024H this is set as ‘1010’ binary
for read and write operations. The next three bits of the
control byte are the Chip Select bits (A2, A1, A0). The
Chip Select bits allow the use of up to eight 24AA024H/
24LC024H devices on the same bus and are used to
select which device is accessed. The Chip Select bits
in the control byte must correspond to the logic levels
on the corresponding A2, A1 and A0 pins for the device
to respond. These bits are in effect the three Most
Significant bits of the word address.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’, a read operation is
selected. When set to a ‘0’, a write operation is
selected. Following the Start condition, the 24AA024H/
24LC024H monitors the SDA bus, checking the control
byte being transmitted. Upon receiving a ‘1010’ code
and appropriate Chip Select bits, the slave device
outputs an Acknowledge signal on the SDA line.
Depending on the state of the R/W bit, the 24AA024H/
24LC024H will select a read or write operation.
DS22102A-page 8
FIGURE 5-1:
CONTROL BYTE FORMAT
Read/Write Bit
Chip Select
Bits
Control Code
S
1
0
1
0
A2
A1
A0 R/W ACK
Slave Address
Start Bit
5.1
Acknowledge Bit
Contiguous Addressing Across
Multiple Devices
The Chip Select bits A2, A1 and A0 can be used to
expand the contiguous address space for up to 16K bits
by adding up to eight 24AA024H/24LC024H devices on
the same bus. In this case, software can use A0 of the
control byte as address bit A9, A1 as address bit A10,
and A2 as address bit A11. It is not possible to
sequentially read across device boundaries.
© 2008 Microchip Technology Inc.
24AA024H/24LC024H
6.0
WRITE OPERATIONS
6.1
Byte Write
The higher order four bits of the word address remain
constant. If the master should transmit more than 16
bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received, an
internal write cycle will begin (Figure 6-2). If an attempt
is made to write to the protected portion of the array
when the hardware write protection has been enabled,
the device will acknowledge the command, but no data
will be written. The write cycle time must be observed
even if write protection is enabled.
Following the Start signal from the master, the device
code (4 bits), the Chip Select bits (3 bits) and the R/W
bit (which is a logic low) are placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
be written into the Address Pointer of the 24AA024H/
24LC024H. After receiving another Acknowledge
signal from the 24AA024H/24LC024H, the master
device will transmit the data word to be written into the
addressed memory location. The 24AA024H/
24LC024H acknowledges again and the master
generates a Stop condition. This initiates the internal
write cycle and the 24AA024H/24LC024H will not
generate Acknowledge signals during this time
(Figure 6-1). If an attempt is made to write to the
protected portion of the array when the hardware write
protection has been enabled, the device will
acknowledge the command, but no data will be written.
The write cycle time must be observed even if write
protection is enabled.
6.2
Note:
Page Write
The write-control byte, word address and the first data
byte are transmitted to the 24AA024H/24LC024H in the
same way as in a byte write. But instead of generating
a Stop condition, the master transmits up to 15
additional data bytes to the 24AA024H/24LC024H that
are temporarily stored in the on-chip page buffer and
will be written into the memory once the master has
transmitted a Stop condition. Upon receipt of each
word, the four lower order Address Pointer bits are
internally incremented by one.
FIGURE 6-1:
6.3
Page write operations are limited to writing
bytes within a single physical page,
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page size’) and end at addresses that are
integer multiples of [page size – 1]. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page, as might be
expected. It is therefore necessary that the
application software prevent page write
operations that would attempt to cross a
page boundary.
Write Protection
The WP pin must be tied to VCC or VSS. If tied to VCC,
half of the array will be write-protected (80h-FFh). If the
WP pin is tied to VSS, write operations to all address
locations are allowed.
BYTE WRITE
Bus Activity
Master
S
T
A
R
T
SDA Line
S
Control
Byte
Word
Address
S
T
O
P
Data
P
A
C
K
Bus Activity
FIGURE 6-2:
A
C
K
A
C
K
PAGE WRITE
Bus Activity
Master
S
T
A
R
T
SDA Line
S
Control
Byte
Bus Activity
© 2008 Microchip Technology Inc.
Word
Address (n)
Data (n)
S
T
O
P
Data (n + 15)
Data (n + 1)
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
DS22102A-page 9
24AA024H/24LC024H
7.0
ACKNOWLEDGE POLLING
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the Stop condition for a write
command has been issued from the master, the device
initiates the internally-timed write cycle and ACK polling
can be initiated immediately. This involves the master
sending a Start condition followed by the control byte
for a Write command (R/W = 0). If the device is still
busy with the write cycle, no ACK will be returned. If no
ACK is returned, the Start bit and control byte must be
re-sent. If the cycle is complete, the device will return
the ACK and the master can then proceed with the next
Read or Write command. See Figure 7-1 for a flow
diagram of this operation.
FIGURE 7-1:
ACKNOWLEDGE POLLING
FLOW
Send
Write Command
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
Did Device
Acknowledge
(ACK = 0)?
No
Yes
Next
Operation
DS22102A-page 10
© 2008 Microchip Technology Inc.
24AA024H/24LC024H
8.0
READ OPERATIONS
Read operations are initiated in the same way as write
operations, with the exception that the R/W bit of the
slave address is set to ‘1’. There are three basic types
of read operations: current address read, random read
and sequential read.
8.1
Current Address Read
The 24AA024H/24LC024H contains an address
counter that maintains the address of the last word
accessed, internally incremented by one. Therefore, if
the previous read access was to address n, the next
current address read operation would access data from
address n + 1. Upon receipt of the slave address with
the R/W bit set to ‘1’, the 24AA024H/24LC024H issues
an acknowledge and transmits the 8-bit data word. The
master will not acknowledge the transfer, but does
generate a Stop condition and the 24AA024H/
24LC024H discontinues transmission (Figure 8-1).
8.2
Random Read
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, the word address must first
be set. This is done by sending the word address to the
24AA024H/24LC024H as part of a write operation.
FIGURE 8-1:
Once the word address is sent, the master generates a
Start condition following the acknowledge. This
terminates the write operation, but not before the
internal Address Pointer is set. The master then issues
the control byte again but with the R/W bit set to a ‘1’.
The 24AA024H/24LC024H will then issue an
acknowledge and transmits the eight-bit data word.
The master will not acknowledge the transfer, but does
generate a Stop condition and the 24AA024H/
24LC024H discontinues transmission (Figure 8-2).
After this command, the internal address counter will
point to the address location following the one that was
just read.
8.3
Sequential Read
Sequential reads are initiated in the same way as a
random read except that after the 24AA024H/
24LC024H transmits the first data byte, the master
issues an acknowledge as opposed to a Stop condition
in a random read. This directs the 24AA024H/
24LC024H to transmit the next sequentially addressed
8-bit word (Figure 8-3).
To provide sequential reads, the 24AA024H/24LC024H
contains an internal Address Pointer which is
incremented by one at the completion of each
operation. This Address Pointer allows the entire
memory contents to be serially read during one
operation. The
internal
Address
Pointer
will
automatically roll over from address FFh to address
00h.
CURRENT ADDRESS READ
Bus Activity
Master
S
T
A
R
T
SDA Line
S
Bus Activity
© 2008 Microchip Technology Inc.
Control
Byte
S
T
O
P
Data
P
A
C
K
N
O
A
C
K
DS22102A-page 11
24AA024H/24LC024H
FIGURE 8-2:
Bus Activity
Master
SDA Line
RANDOM READ
S
T
A
R
T
Control
Byte
S
Bus Activity
Master
Control
Byte
S
T
O
P
Data (n)
P
S
A
C
K
A
C
K
Bus Activity
FIGURE 8-3:
S
T
A
R
T
Word
Address (n)
N
O
A
C
K
A
C
K
SEQUENTIAL READ
Control
Byte
Data (n)
Data (n + 1)
Data (n + 2)
S
T
O
P
Data (n + X)
P
SDA Line
Bus Activity
DS22102A-page 12
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
© 2008 Microchip Technology Inc.
24AA024H/24LC024H
9.0
PACKAGING INFORMATION
9.1
Package Marking Information
8-Lead PDIP (300 mil)
Example:
24LC024H
I/P e3 12F
0821
XXXXXXXX
T/XXXNNN
YYWW
8-Lead SOIC (3.90 mm)
XXXXXXXT
XXXXYYWW
NNN
8-Lead TSSOP
Example:
24L024HI
SN e3 0821
12F
Example:
XXXX
L24H
TYWW
I821
NNN
12F
8-Lead MSOP
XXXXT
YWWNNN
8-Lead 2x3 TDFN
XXX
YWW
NN
© 2008 Microchip Technology Inc.
Example:
4L24HI
82112F
Example:
AF4
821
12
DS22102A-page 13
24AA024H/24LC024H
1st Line Marking Codes
Part Number
TSSOP
MSOP
TDFN
I
E
I
E
I
E
24AA024H
A24H
A24H
4A24HI
4A24HE
AF1
AF2
24LC024H
L24H
L24H
4L24HI
4L24HE
AF4
AF5
Legend: XX...X
T
Y
YY
WW
NNN
e3
Note:
Part number or part number code
Temperature (I, E)
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code (2 characters for small packages)
Pb-free JEDEC designator for Matte Tin (Sn)
Note:
For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion.
*Standard OTP marking consists of Microchip part number, year code, week code, and traceability code.
DS22102A-page 14
© 2008 Microchip Technology Inc.
24AA024H/24LC024H
3
&'
!&" &4# *!(!!&
4%&
&#&
&&255***'
'54
N
NOTE 1
E1
1
3
2
D
E
A2
A
L
A1
c
e
eB
b1
b
6&!
'!
9'&!
7"')
%!
7,8.
7
7
7:
;
<
&
&
&
=
=
##4
4!!
-
1!&
&
=
=
"# &
"# >#&
.
-
-
##4>#&
.
#&
9
* 9#>#&
:
*+
1,
-
!"#$%&" ' ()"&'"!&)
&#*&&&#
+%&, & !&
- '!
!#.#
&"#'
#%!
& "!
!
#%!
& "!
!!
&$#/ !#
'!
#&
.0
1,21!'!
&$& "!
**&
"&&
!
* ,