APT5020SVFRG/TR

APT5020SVFR 26A 0.200Ω 500V POWER MOS V ® FREDFET D3PAK V® Power MOS is a new generation of high voltage N-Channel enhancement mode power MOSFETs. This new technology minimizes the JFET effect, increases packing density and reduces the on-resistance. Power MOS V® also achieves faster switching speeds through optimized gate layout. • Fast Recovery Body Diode • 100% Avalanche Tested D FREDFET • Surface Mount D3PAK Package • Lower Leakage G • Faster Switching S MAXIMUM RATINGS Symbol VDSS ID All Ratings: TC = 25°C unless otherwise specified. Parameter APT5020SVFR UNIT 500 Volts Drain-Source Voltage 26 Continuous Drain Current @ TC = 25°C 1 Amps IDM Pulsed Drain Current VGS Gate-Source Voltage Continuous ±30 Gate-Source Voltage Transient ±40 Total Power Dissipation @ TC = 25°C 300 Watts Linear Derating Factor 2.4 W/°C VGSM PD TJ,TSTG 104 -55 to 150 Operating and Storage Junction Temperature Range TL Lead Temperature: 0.063" from Case for 10 Sec. IAR Avalanche Current 1 26 1 Repetitive Avalanche Energy EAS Single Pulse Avalanche Energy °C 300 (Repetitive and Non-Repetitive) EAR Volts Amps 30 4 mJ 1300 STATIC ELECTRICAL CHARACTERISTICS BVDSS ID(on) RDS(on) IDSS IGSS VGS(th) Characteristic / Test Conditions MIN Drain-Source Breakdown Voltage (VGS = 0V, ID = 250µA) 500 Volts 26 Amps On State Drain Current 2 (VDS > I D(on) x R DS(on) Max, VGS = 10V) Drain-Source On-State Resistance 2 TYP (VGS = 10V, 0.5 ID[Cont.]) MAX 0.20 Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V) 250 UNIT Ohms µA Zero Gate Voltage Drain Current (VDS = 0.8 VDSS, VGS = 0V, TC = 125°C) 1000 Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) ±100 nA 4 Volts Gate Threshold Voltage (VDS = VGS, ID = 1.0mA) 2 CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. USA APT Website - http://www.advancedpower.com 405 S.W. Columbia Street Bend, Oregon 97702 -1035 Phone: (541) 382-8028 FAX: (541) 388-0364 F-33700 Merignac - France Phone: (33) 5 57 92 15 15 FAX: (33) 5 56 47 97 61 EUROPE Avenue J.F. Kennedy Bât B4 Parc Cadéra Nord 050-5569 Rev B Symbol APT5020SVFR DYNAMIC CHARACTERISTICS Symbol Test Conditions Characteristic MIN TYP MAX Ciss Input Capacitance VGS = 0V 3700 4440 Coss Output Capacitance VDS = 25V 510 715 Crss Reverse Transfer Capacitance f = 1 MHz 200 300 Qg Total Gate Charge VGS = 10V 150 225 Qgs Gate-Source Charge VDD = 0.5 VDSS Qgd Gate-Drain ("Miller") Charge ID = ID [Cont.] @ 25°C 25 70 37 105 VGS = 15V 12 25 t d(on) 3 Turn-on Delay Time tr Rise Time t d(off) Turn-off Delay Time tf VDD = 0.5 VDSS 10 20 ID = ID [Cont.] @ 25°C 50 75 RG = 1.8Ω 8 15 TYP MAX Fall Time UNIT pF nC ns SOURCE-DRAIN DIODE RATINGS AND CHARACTERISTICS Symbol Characteristic / Test Conditions IS ISM Pulsed Source Current 1 VSD Diode Forward Voltage 2 dv/ MIN 26 Continuous Source Current (Body Diode) Peak Diode Recovery dt dv/ 104 (Body Diode) dt (VGS = 0V, IS = -ID [Cont.]) 5 UNIT Amps 1.3 Volts 5 V/ns t rr Reverse Recovery Time (IS = -ID [Cont.], di/dt = 100A/µs) Tj = 25°C 250 Tj = 125°C 500 Q rr Reverse Recovery Charge (IS = -ID [Cont.], di/dt = 100A/µs) Tj = 25°C 1.3 Tj = 125°C 4.5 IRRM Peak Recovery Current (IS = -ID [Cont.], di/dt = 100A/µs) Tj = 25°C 12 Tj = 125°C 18 ns µC Amps THERMAL CHARACTERISTICS Symbol Characteristic MIN TYP MAX 0.42 RθJC Junction to Case RθJA Junction to Ambient 1 Repetitive Rating: Pulse width limited by maximum junction temperature. 2 Pulse Test: Pulse width < 380 µS, Duty Cycle < 2% 40 VR = 200V. D=0.5 0.05 0.1 0.05 0.01 0.005 Note: 0.02 PDM Z JC, THERMAL IMPEDANCE (°C/W) θ 050-5569 Rev B 0.5 0.2 0.01 SINGLE PULSE t1 t2 Duty Factor D = t1/t2 Peak TJ = PDM x ZθJC + TC 0.001 10-5 10-4 °C/W 3 See MIL-STD-750 Method 3471 4 Starting T = +25°C, L = 3.85mH, R = 25Ω, Peak I = 26A j G L 5 I ≤ -I [Cont.], di/ = 100A/µs, V S D DD ≤ VDSS, Tj ≤ 150°C, RG = 2.0Ω, dt APT Reserves the right to change, without notice, the specifications and information contained herein. 0.1 UNIT 10-3 10-2 10-1 1.0 10 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 1, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION APT5020SVFR 50 VGS=6V, 7V, 10V & 15V VGS=15V ID, DRAIN CURRENT (AMPERES) 40 5.5V 30 5V 20 10 4.5V 4V 0 VDS> ID (ON) x RDS (ON)MAX. 250µSEC. PULSE TEST @