Features
• Fast Read Access Time - 120 ns
• Dual Voltage Range Operation
•
•
•
•
•
•
•
•
– Unregulated Battery Power Supply Range, 2.7V to 3.6V
or Standard 5V ± 10% Supply Range
Pin Compatible with JEDEC Standard AT27C4096
Low Power CMOS Operation
– 20 µA max. (less than 1 µA typical) Standby for VCC = 3.6V
– 36 mW max. Active at 5 MHz for VCC = 3.6V
JEDEC Standard Surface Mount Packages
– 44-Lead PLCC
– 40-Lead TSOP (10 x 14mm)
High Reliability CMOS Technology
– 2,000V ESD Protection
– 200 mA Latchup Immunity
Rapid™ Programming algorithm - 100 µs/word (typical)
CMOS and TTL Compatible Inputs and Outputs
– JEDEC Standard for LVTTL and LVBO
Integrated Product Identification Code
Commercial and Industrial Temperature Ranges
4-Megabit
(256K x 16)
Unregulated
Battery-Voltage™
High-Speed OTP
EPROM
Description
The AT27BV4096 is a high performance, low power, low voltage 4,194,304-bit onetime programmable read only memory (OTP EPROM) organized as 256K by 16 bits. It
requires only one supply in the range of 2.7V to 3.6V in normal read mode operation.
The by-16 organization makes this part ideal for portable and handheld 16 and 32 bit
microprocessor based systems using either regulated or unregulated battery power.
(continued)
AT27BV4096
Pin Configurations
Pin Name
Function
A0 - A17
Addresses
O0 - O15
Outputs
CE
Chip Enable
OE
Output Enable
NC
No Connect
Note:
TSOP Top View
Type 1
Both GND pins must be connected.
39
38
37
36
35
34
33
32
31
30
29
18
19
20
21
22
23
24
25
26
27
28
7
8
9
10
11
12
13
14
15
16
17
A13
A12
A11
A10
A9
GND
NC
A8
A7
A6
A5
O3
O2
O1
O0
OE
NC
A0
A1
A2
A3
A4
O12
O11
O10
O9
O8
GND
NC
O7
O6
O5
O4
6
5
4
3
2
1
44
43
42
41
40
O13
O14
O15
CE
VPP
NC
VCC
A17
A16
A15
A14
PLCC Top View
Note: PLCC package pins 1 and 23 are
DON’T CONNECT.
A9
A10
A11
A12
A13
A14
A15
A16
A17
VCC
VPP
CE
O15
O14
O13
O12
O11
O10
O9
O8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
GND
A8
A7
A6
A5
A4
A3
A2
A1
A0
OE
O0
O1
O2
O3
O4
O5
O6
O7
GND
Rev. 0640B–10/98
1
Atmel’s innovative design techniques provide fast speeds
that rival 5V parts while keeping the low power consumption of a 3V supply. At V CC = 2.7V, any word can be
accessed in less than 120 ns. With a typical power dissipation of only 18 mW at 5 MHz and VCC = 3V, the
AT27BV4096 consumes less than one fifth the power of a
standard 5V EPROM.
Standby mode supply current is typically less than 1 µA at
3V. The AT27BV4096 simplifies system design and
stretches battery lifetime even further by eliminating the
need for power supply regulation.
The AT27BV4096 is available in industry standard JEDECapproved one-time programmable (OTP) plastic PLCC and
TSOP packages. All devices feature two-line control (CE,
OE) to give designers the flexibility to prevent bus
contention.
The AT27BV4096 operating with V CC at 3.0V produces TTL
level outputs that are compatible with standard TTL logic
devices operating at VCC = 5.0V. At VCC = 2.7V, the part is
compatible with JEDEC approved low voltage battery operation (LVBO) interface specifications. The device is also
capable of standard 5-volt operation making it ideally suited
for dual supply range systems or card products that are
pluggable in both 3-volt and 5-volt hosts.
Atmel’s AT27BV4096 has additional features to ensure
high quality and efficient production use. The Rapid™ Pro-
Block Diagram
2
AT27BV4096
gramming Algorithm reduces the time required to program
the part and guarantees reliable programming. Programming time is typically only 100 µs/word. The Integrated
Product Identification Code electronically identifies the
device and manufacturer. This feature is used by industry
standard programming equipment to select the proper programming algorithms and voltages. The AT27BV4096 programs exactly the same way as a standard 5V AT27C4096
and uses the same programming equipment.
System Considerations
Switching between active and standby conditions via the
Chip Enable pin may produce transient voltage excursions.
Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device
non-conformance. At a minimum, a 0.1 µF high frequency,
low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected
between the V CC and Ground terminals of the device, as
close to the device as possible. Additionally, to stabilize the
supply voltage level on printed circuit boards with large
EPROM arrays, a 4.7 µF bulk electrolytic capacitor should
be utilized, again connected between the VCC and Ground
terminals. This capacitor should be positioned as close as
possible to the point where the power supply is connected
to the array.
AT27BV4096
Absolute Maximum Ratings*
*NOTICE:
Temperature Under Bias ................................ -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with
Respect to Ground .........................................-2.0V to +7.0V(1)
Voltage on A9 with
Respect to Ground ......................................-2.0V to +14.0V(1)
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability
VPP Supply Voltage with
Respect to Ground .......................................-2.0V to +14.0V(1)
Note:
1.
Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is
VCC + 0.75V dc which may be exceeded if certain precautions are observed (consult application notes) and which may
overshoot to +7.0V for pulses of less than 20 ns.
Operating Modes
Mode \ Pin
Read
CE
(2)
VIL
Output Disable
(2)
Standby(2)
Rapid Program
(3)
(3)
PGM Verify
OE
VIL
Ai
VPP
Ai
(1)
X
VCC
VCC
DOUT
(2)
High Z
High Z
X
VIH
X
X
VCC
VIH
X
X
X (5)
VCC(2)
VIL
VIH
VIH
VIL
Ai
Ai
VPP
VPP
VCC
(3)
DIN
VCC
(3)
DOUT
(3)
High Z
(3)
PGM Inhibit
VIH
VIH
X
VPP
VCC
Product Identification(3)(5)
VIL
VIL
A9 = VH(4)
A0 = VIH or VIL
A1 - A17 = VIL
VCC
VCC(3)
Notes:
Outputs
(2)
Identification Code
1. X can be VIL or VIH.
2. Read, output disable, and standby modes require, 2.7V ≤ VCC ≤ 3.6V, or 4.5V ≤ VCC ≤ 5.5V.
3. Refer to Programming Characteristics. Programming modes require VCC = 6.5V.
4. VH = 12.0 ± 0.5V.
5. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled low
(VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte.
3
DC and AC Operating Conditions for Read Operation
Operating Temperature
(Case)
AT27BV4096-12
AT27BV4096-15
0°C - 70°C
0°C - 70°C
-40°C - 85°C
-40°C - 85°C
2.7V to 3.6V
2.7V to 3.6V
5V ± 10%
5V ± 10%
Com.
Ind.
VCC Power Supply
DC and Operating Characteristics for Read Operation
Symbol
Parameter
Condition
Min
Max
Units
VCC = 2.7V to 3.6V
ILI
Input Load Current
VIN = 0V to VCC
±1
µA
ILO
Output Leakage Current
VOUT = 0V to VCC
±5
µA
VPP = VCC
10
µA
ISB1 (CMOS), CE = VCC ± 0.3V
20
µA
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
100
µA
f = 5 MHz, IOUT = 0 mA, CE = VIL, VCC = 3.6V
10
mA
IPP1(2)
VPP
ISB
VCC(1) Standby Current
ICC
VCC Active Current
VIL
Input Low Voltage
VIH
Input High Voltage
VOL
VOH
(1)
Read/Standby Current
Output Low Voltage
Output High Voltage
VCC = 3.0 to 3.6V
-0.6
0.8
V
VCC = 2.7 to 3.6V
-0.6
0.2 x VCC
V
VCC = 3.0 to 3.6V
2.0
VCC + 0.5
V
VCC = 2.7 to 3.6V
0.7 x VCC
VCC + 0.5
V
IOL = 2.0 mA
0.4
V
IOL = 100 µA
0.2
V
IOL = 20 µA
0.1
V
IOH = -2.0 mA
2.4
V
IOH = -100 µA
VCC - 0.2
V
IOH = -20 µA
VCC - 0.1
V
VCC = 4.5V to 5.5V
ILI
Input Load Current
VIN = 0V to VCC
±1
µA
ILO
Output Leakage Current
VOUT = 0V to VCC
±5
µA
VPP = VCC
10
µA
ISB1 (CMOS), CE = VCC ± 0.3V
100
µA
ISB2 (TTL), CE = 2.0 to VCC + 0.5V
1
mA
f = 5 MHz, IOUT = 0 mA, CE = VIL
40
mA
IPP1(2)
VPP
ISB
VCC(1) Standby Current
ICC
VCC Active Current
VIL
Input Low Voltage
-0.6
0.8
V
VIH
Input High Voltage
2.0
VCC + 0.5
V
VOL
Output Low Voltage
IOL = 2.1 mA
0.4
V
VOH
Output High Voltage
IOH = -400 µA
Notes:
(1)
Read/Standby Current
2.4
V
1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP.
2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and IPP.
4
AT27BV4096
AT27BV4096
AC Characteristics for Read Operation
VCC = 2.7V to 3.6V and 4.5V to 5.5V
Symbol
Parameter
Condition
tACC(3)
Address to Output Delay
CE = OE
= VIL
tCE(2)
CE to Output Delay
tOE(2)(3)
OE to Output Delay
tDF(4)(5)
OE or CE High to Output Float,
whichever occurred first
tOH
Output Hold from Address, CE or OE,
whichever occurred first
AT27BV4096-12
AT27BV4096-15
Min
Min
Max
Max
Units
120
150
ns
OE = VIL
120
150
ns
CE = VIL
35
50
ns
30
40
ns
0
0
ns
AC Waveforms for Read Operation(1)
Notes:
1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified.
2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE.
3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC.
4. This parameter is only sampled and is not 100% tested.
5. Output float is defined as the point when data is no longer driven.
6. When reading a 27BV4096, a 0.1 µF capacitor is required across VCC and ground to suppress spurious voltage transients.
5
Input Test Waveforms and
Measurement Levels
Output Test Load
tR, tF < 20 ns (10% to 90%)
Note: CL = 100 pF including
jig capacitance.
Pin Capacitance
f = 1 MHz T = 25°C(1)
Symbol
Typ
Max
Units
Conditions
CIN
4
10
pF
VIN = 0V
COUT
8
12
pF
VOUT = 0V
Note:
6
1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested.
AT27BV4096
AT27BV4096
Programming Waveforms(1)
Notes:
1.
The Input Timing Reference is 0.8V for VIL and 2.0V for VIH.
2.
tOE and tDFP are characteristics of the device but must be accommodated by the programmer.
3.
When programming the AT27BV4096 a 0.1 µF capacitor is required across VPP and ground to suppress spurious voltage
transients.
DC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V
Limits
Symbol
Parameter
Test Conditions
ILI
Input Load Current
VIN = VIL, VIH
VIL
Input Low Level
VIH
Input High Level
VOL
Output Low Voltage
IOL = 2.1 mA
VOH
Output High Voltage
IOH = -400 µA
ICC2
VCC Supply Current (Program and Verify)
IPP2
VPP Supply Current
VID
A9 Product Identification Voltage
Min
Max
Units
±10
mA
-0.6
0.8
V
2.0
VCC + 0.1
V
0.4
V
2.4
CE = VIL
11.5
V
50
mA
30
mA
12.5
V
7
AC Programming Characteristics
TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V
Limits
(1)
Symbol
Parameter
tAS
Address Setup Time
2
µs
tCES
CE Setup Time
2
µs
tOES
OE Setup Time
2
µs
tDS
Data Setup Time
2
µs
tAH
Address Hold Time
0
µs
tDH
Data Hold Time
2
µs
tDFP
OE High to Output Float Delay(2)
tVPS
VPP Setup Time
tVCS
VCC Setup Time
tPW
PGM Program Pulse Width(3)
tOE
Data Valid from OE
tPRT
VPP Pulse Rise Time During
Programming
Notes:
Test Conditions
Min
Input Rise and Fall Times:
(10% to 90%) 20 ns
Input Pulse Levels:
0.45V to 2.4V
Max
0
Input Timing Reference Level:
0.8V to 2.0V
Output Timing Reference Level:
0.8V to 2.0V
Units
130
ns
2
µs
2
µs
47.5
52.5
µs
150
ns
50
ns
1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP.
2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven—
see timing diagram.
3. Program Pulse width tolerance is 50 µsec ± 5%.
Atmel’s 27BV4096 Integrated Product Identification Code(1)
Pins
A0
O15-O8
O7
O6
O5
O4
O3
O2
O1
O0
Hex
Data
Manufacturer
0
0
0
0
0
1
1
1
1
0
001E
Device Type
1
0
1
1
1
1
0
1
0
0
00F4
Codes
Note:
8
1. The AT27BV4096 has the same Product Identification Code as the AT27C4096. Both are programming compatible.
AT27BV4096
AT27BV4096
Rapid Programming Algorithm
A 50 µs CE pulse width is used to program. The address is
set to the first location. V CC is raised to 6.5V and V PP is
raised to 13.0V. Each address is first programmed with one
50 µs CE pulse without verification. Then a verification /
reprogramming loop is executed for each address. In the
event a word fails to pass verification, up to 10 successive
50 µs pulses are applied with a verification after each
pulse. If the word fails to verify after 10 pulses have been
applied, the part is considered failed. After the word verifies
properly, the next address is selected until all have been
checked. VPP is then lowered to 5.0V and VCC to 5.0V. All
words are read again and compared with the original data
to determine if the device passes or fails.
START
ADDR = FIRST LOCATION
VCC = 6.5V
VPP = 13.0V
PROGRAM ONE 50 µS PULSE
INCREMENT ADDRESS
NO
LAST
ADDR.?
YES
ADDR = FIRST LOCATION
INCREMENT ADDRESS
X=0
NO
LAST
ADDR.?
PASS
VERIFY
WORD
FAIL
INCREMENT X
YES
PROGRAM ONE 50 µS PULSE
X = 10?
YES
VCC = 5.0V
VPP = 5.0V
COMPARE
ALL WORDS
TO ORIGINAL
DATA
NO
FAIL
DEVICE
FAILED
PASS
DEVICE
PASSED
9
Ordering Information
tACC
(ns)
ICC (mA)
Active
Standby
Ordering Code
Package
44J
40V
Commercial
(0°C to 70°C)
8
0.02
8
0.02
AT27BV4096-12JI
AT27BV4096-12VI
44J
40V
Industrial
(-40°C to 85°C)
8
0.02
AT27BV4096-15JC
AT27BV4096-15VC
44J
40V
Commercial
(0°C to 70°C)
8
0.02
AT27BV4096-15JI
AT27BV4096-15VI
44J
40V
Industrial
(-40°C to 85°C)
120
150
Package Type
44J
44-Lead, Plastic J-Leaded Chip Carrier (PLCC)
40V
40-Lead, Plastic Thin Small Outline Package (TSOP) 10 x 14 mm
10
Operation Range
AT27BV4096-12JC
AT27BV4096-12VC
AT27BV4096
AT27BV4096
Packaging Information
44J, 44-Lead. Plastic J-Leaded Chip Carrier (PLCC)
Dimensions in Inches and (Millimeters)
JEDEC STANDARD MS-018 AC
40V, 40-Lead. Plastic Thin Small Outline Package
(TSOP)
Dimensions in Millimeters and (Inches)
JEDEC OUTLINE MO-142 CA
.045(1.14) X 45°
PIN NO. 1
IDENTIFY
.045(1.14) X 30° - 45°
.012(.305)
.008(.203)
.630(16.0)
.590(15.0)
.656(16.7)
SQ
.650(16.5)
.032(.813)
.026(.660)
.695(17.7)
SQ
.685(17.4)
.050(1.27) TYP
.500(12.7) REF SQ
.021(.533)
.013(.330)
.043(1.09)
.020(.508)
.120(3.05)
.090(2.29)
.180(4.57)
.165(4.19)
.022(.559) X 45° MAX (3X)
11
Atmel Headquarters
Atmel Operations
Corporate Headquarters
Atmel Colorado Springs
2325 Orchard Parkway
San Jose, CA 95131
TEL (408) 441-0311
FAX (408) 487-2600
Europe
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL (719) 576-3300
FAX (719) 540-1759
Atmel Rousset
Atmel U.K., Ltd.
Coliseum Business Centre
Riverside Way
Camberley, Surrey GU15 3YL
England
TEL (44) 1276-686677
FAX (44) 1276-686697
Zone Industrielle
13106 Rousset Cedex, France
TEL (33) 4 42 53 60 00
FAX (33) 4 42 53 60 01
Asia
Atmel Asia, Ltd.
Room 1219
Chinachem Golden Plaza
77 Mody Road
Tsimshatsui East
Kowloon, Hong Kong
TEL (852) 27219778
FAX (852) 27221369
Japan
Atmel Japan K.K.
Tonetsu Shinkawa Bldg., 9F
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
Fax-on-Demand
North America:
1-(800) 292-8635
International:
1-(408) 441-0732
e-mail
literature@atmel.com
Web Site
http://www.atmel.com
BBS
1-(408) 436-4309
© Atmel Corporation 1998.
Atmel Cor poration makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s website. The Company assumes no responsibility for
any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without
notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual proper ty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are
not authorized for use as critical components in life suppor t devices or systems.
Marks bearing
®
and/or
™
are registered trademarks and trademarks of Atmel Corporation.
Terms and product names in this document may be trademarks of others.
Printed on recycled paper.
0640B–10/98/xM
工商网监
湘ICP备2023018690号
