AT28C64E-15JI

Features • Fast Read Access Time – 120 ns • Fast Byte Write – 200 µs or 1 ms • Self-timed Byte Write Cycle • • • • • • • – Internal Address and Data Latches – Internal Control Timer – Automatic Clear Before Write Direct Microprocessor Control – READY/BUSY Open Drain Output – DATA Polling Low Power – 30 mA Active Current – 100 µA CMOS Standby Current High Reliability – Endurance: 104 or 105 Cycles – Data Retention: 10 Years 5V ± 10% Supply CMOS and TTL Compatible Inputs and Outputs JEDEC Approved Byte-wide Pinout Commercial and Industrial Temperature Ranges 64K (8K x 8) Parallel EEPROMs AT28C64 AT28C64X Description The AT28C64 is a low-power, high-performance 8,192 words by 8-bit nonvolatile electrically erasable and programmable read only memory with popular, easy-to-use features. The device is manufactured with Atmel’s reliable nonvolatile technology. (continued) Pin Configurations A0 - A12 Addresses CE Chip Enable OE Output Enable WE Write Enable I/O0 - I/O7 Data Inputs/Outputs RDY/BUSY Ready/Busy Output NC No Connect DC Don’t Connect VCC WE NC A8 A9 A11 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 A7 A12 RDY/BUSY (or NC) DC VCC WE NC 28 27 26 25 24 23 22 21 20 19 18 17 16 15 A6 A5 A4 A3 A2 A1 A0 NC I/O0 5 6 7 8 9 10 11 12 13 29 28 27 26 25 24 23 22 21 A8 A9 A11 NC OE A10 CE I/O7 I/O6 I/O1 I/O2 VSS DC I/O3 I/O4 I/O5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 LCC, PLCC Top View TSOP Top View OE A11 A9 A8 NC WE VCC RDY/BUSY (or NC) A12 A7 A6 A5 A4 A3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 RDY/BUSY (or NC) A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 GND 4 3 2 1 32 31 30 Function 14 15 16 17 18 19 20 Pin Name PDIP, SOIC Top View Rev. 0001H–12/99 Note: PLCC package pins 1 and 17 are DON’T CONNECT. 1 The AT28C64 is accessed like a Static RAM for the read or write cycles without the need for external components. During a byte write, the address and data are latched internally, freeing the microprocessor address and data bus for other operations. Following the initiation of a write cycle, the device will go to a busy state and automatically clear and write the latched data using an internal control timer. The device includes two methods for detecting the end of a write cycle, level detection of RDY/BUSY (unless pin 1 is N.C.) and DATA Polling of I/O7 . Once the end of a write cycle has been detected, a new access for a read or write can begin. The CMOS technology offers fast access times of 120 ns at low power dissipation. When the chip is deselected the standby current is less than 100 µA. Atmel’s AT28C64 has additional features to ensure high quality and manufacturability. The device utilizes error correction internally for extended endurance and for improved data retention characteristics. An extra 32 bytes of EEPROM are available for device identification or tracking. Block Diagram Absolute Maximum Ratings* Temperature under Bias ................................ -55°C to +125°C Storage Temperature ..................................... -65°C to +150°C All Input Voltages (including NC Pins) with Respect to Ground ...................................-0.6V to +6.25V All Output Voltages with Respect to Ground .............................-0.6V to VCC + 0.6V Voltage on OE and A9 with Respect to Ground ...................................-0.6V to +13.5V 2 AT28C64(X) *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability AT28C64(X) Device Operation READ: The AT28C64 is accessed like a Static RAM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in a high impedance state whenever CE or OE is high. This dual line control gives designers increased flexibility in preventing bus contention. BYTE WRITE: Writing data into the AT28C64 is similar to writing into a Static RAM. A low pulse on the WE or CE input with OE high and CE or WE low (respectively) initiates a byte write. The address location is latched on the falling edge of WE (or CE); the new data is latched on the rising edge. Internally, the device performs a self-clear before write. Once a byte write has been started, it will automatically time itself to completion. Once a programming operation has been initiated and for the duration of tWC, a read operation will effectively be a polling operation. FAST BYTE WRITE: The AT28C64E offers a byte write time of 200 µs maximum. This feature allows the entire device to be rewritten in 1.6 seconds. READY/BUSY: Pin 1 is an open drain RDY/BUSY output that can be used to detect the end of a write cycle. RDY/BUSY is actively pulled low during the write cycle and is released at the completion of the write. The open drain connection allows for OR-tying of several devices to the same RDY/BUSY line. The RDY/BUSY pin is not connected for the AT28C64X. DATA POLLING: The AT28C64 provides DATA Polling to signal the completion of a write cycle. During a write cycle, an attempted read of the data being written results in the complement of that data for I/O 7 (the other outputs are indeterminate). When the write cycle is finished, true data appears on all outputs. WRITE PROTECTION: Inadvertent writes to the device are protected against in the following ways: (a) VCC sense – if VCC is below 3.8V (typical) the write function is inhibited; (b) VCC power on delay – once VCC has reached 3.8V the device will automatically time out 5 ms (typical) before allowing a byte write; and (c) write inhibit – holding any one of OE low, CE high or WE high inhibits byte write cycles. CHIP CLEAR: The contents of the entire memory of the AT28C64 may be set to the high state by the CHIP CLEAR operation. By setting CE low and OE to 12 volts, the chip is cleared when a 10 msec low pulse is applied to WE. D E V I C E I DE NT I FI C A TI O N : A n e x t r a 3 2 b y t e s o f EEPROM memory are available to the user for device identification. By raising A9 to 12 ± 0.5V and using address locations 1FE0H to 1FFFH the additional bytes may be written to or read from in the same manner as the regular memory array. 3 DC and AC Operating Range AT28C64-12 AT28C64-15 AT28C64-20 AT28C64-25 0°C - 70°C 0°C - 70°C 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C -40°C - 85°C -40°C - 85°C 5V ± 10% 5V ± 10% 5V ± 10% 5V ± 10% Mode CE OE WE I/O Read VIL VIL VIH DOUT VIL VIH VIL DIN VIH (1) X High Z Com. Operating Temperature (Case) Ind. VCC Power Supply Operating Modes Write (2) Standby/Write Inhibit X Write Inhibit X X VIH Write Inhibit X VIL X Output Disable X VIH X High Z VIL High Z Chip Erase Notes: VIL VH (3) 1. X can be VIL or VIH. 2. Refer to AC programming waveforms. 3. VH = 12.0V ± 0.5V. DC Characteristics Symbol Parameter Condition ILI Input Load Current ILO Max Units VIN = 0V to VCC + 1V 10 µA Output Leakage Current VI/O = 0V to VCC 10 µA ISB1 VCC Standby Current CMOS CE = VCC - 0.3V to VCC + 1.0V 100 µA Com. 2 mA ISB2 VCC Standby Current TTL CE = 2.0V to VCC + 1.0V Ind. 3 mA 30 mA VCC Active Current AC f = 5 MHz; IOUT = 0 mA CE = VIL Com. ICC Ind. 45 mA VIL Input Low Voltage 0.8 V VIH Input High Voltage VOL Output Low Voltage IOL = 2.1 mA = 4.0 mA for RDY/BUSY VOH Output High Voltage IOH = -400 µA 4 Min 2.0 AT28C64(X) V 0.45 2.4 V V AT28C64(X) AC Read Characteristics Symbol Parameter tACC AT28C64-12 AT28C64-15 AT28C64-20 AT28C64-25 Min Min Min Min Max Max Max Max Units Address to Output Delay 120 150 200 250 ns (1) CE to Output Delay 120 150 200 250 ns (2) OE to Output Delay 10 60 10 70 10 80 10 100 ns tDF(3)(4) CE or OE High to Output Float 0 45 0 50 0 55 0 60 ns tOH Output Hold from OE, CE or Address, whichever occurred first 0 tCE tOE 0 0 0 ns AC Read Waveforms(1)(2)(3)(4) Notes: 1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change without impact on tACC. 3. tDF is specified from OE or CE whichever occurs first (CL = 5 pF). 4. This parameter is characterized and is not 100% tested. Input Test Waveforms and Measurement Level Output Test Load tR, tF < 20 ns Pin Capacitance f = 1 MHz, T = 25°C(1) Symbol Typ Max Units Conditions CIN 4 6 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 1. This parameter is characterized and is not 100% tested. 5 AC Write Characteristics Symbol Parameter Min tAS, tOES Address, OE Setup Time 10 ns tAH Address Hold Time 50 ns tWP Write Pulse Width (WE or CE) 100 tDS Data Setup Time 50 ns tDH, tOEH Data, OE Hold Time 10 ns tCS, tCH CE to WE and WE to CE Setup and Hold Time 0 ns tDB Time to Device Busy tWC Write Cycle Time (option available) AT28C64 AT28C64E AC Write Waveforms WE Controlled CE Controlled 6 AT28C64(X) Max 1000 Units ns 50 ns 1 ms 200 µs AT28C64(X) Data Polling Characteristics(1) Symbol Parameter tDH Data Hold Time tOEH OE Hold Time Min OE to Output Delay tWR Write Recovery Time Notes: Max Units 10 ns 10 ns (2) tOE Typ ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See “AC Read Characteristics”. Data Polling Waveforms Chip Erase Waveforms tS = tH = 1 µsec (min.) tW = 10 msec (min.) VH = 12.0 ± 0.5V 7 8 AT28C64(X) AT28C64(X) AT28C64 Ordering Information ICC (mA) tACC (ns) Active Standby Ordering Code Package 120 30 0.1 AT28C64(E)-12JC AT28C64(E)-12PC AT28C64(E)-12SC AT28C64(E)-12TC 32J 28P6 28S 28T Commercial (0°C to 70°C) 45 0.1 AT28C64(E)-12JI AT28C64(E)-12PI AT28C64(E)-12SI AT28C64(E)-12TI 32J 28P6 28S 28T Industrial (-40°C to 85°C) 30 0.1 AT28C64(E)-15JC AT28C64(E)-15PC AT28C64(E)-15SC AT28C64(E)-15TC 32J 28P6 28S 28T Commercial (0°C to 70°C) 45 0.1 AT28C64(E)-15JI AT28C64(E)-15PI AT28C64(E)-15SI AT28C64(E)-15TI 32J 28P6 28S 28T Industrial (-40°C to 85°C) 30 0.1 AT28C64(E)-20JC AT28C64(E)-20PC AT28C64(E)-20SC AT28C64(E)-20TC 32J 28P6 28S 28T Commercial (0°C to 70°C) 45 0.1 AT28C64(E)-20JI AT28C64(E)-20PI AT28C64(E)-20SI AT28C64(E)-20TI 32J 28P6 28S 28T Industrial (-40°C to 85°C) 30 0.1 AT28C64(E)-25JC AT28C64(E)-25PC AT28C64(E)-25SC AT28C64(E)-25TC 32J 28P6 28S 28T Commercial (0°C to 70°C) 45 0.1 AT28C64(E)-25JI AT28C64(E)-25PI AT28C64(E)-25SI AT28C64(E)-25TI 32J 28P6 28S 28T Industrial (-40°C to 85°C) 150 200 250 Operation Range Package Type 32J 32-lead, Plastic J-leaded Chip Carrier (PLCC) 28P6 28-lead, 0.600" Wide, Plastic Dull Inline Package (PDIP) 28S 28-lead, 0.300" Wide, Plastic Gull Wing, Small Outline (SOIC) 28T 28-lead, Plastic Thin Small Outline Package (TSOP) Options Blank Standard Device: Endurance = 10K Write Cycles; Write Time = 1 ms E High Endurance Option: Endurance = 100K Write Cycles; Write Time = 200 µs 9 AT28C64X Ordering Information ICC (mA) tACC (ns) Active Standby Ordering Code Package 150 30 0.1 AT28C64X-15JC AT28C64X-15PC AT28C64X-15SC AT28C64X-15TC 32J 28P6 28S 28T Commercial (0°C to 70°C) 45 0.1 AT28C64X-15JI AT28C64X-15PI AT28C64X-15SI AT28C64X-15TI 32J 28P6 28S 28T Industrial (-40°C to 85°C) 30 0.1 AT28C64X-20JC AT28C64X-20PC AT28C64X-20SC AT28C64X-20TC 32J 28P6 28S 28T Commercial (0°C to 70°C) 45 0.1 AT28C64X-20JI AT28C64X-20PI AT28C64X-20SI AT28C64X-20TI 32J 28P6 28S 28T Industrial (-40°C to 85°C) 30 0.1 AT28C64X-25JC AT28C64X-25PC AT28C64X-25SC AT28C64X-25TC 32J 28P6 28S 28T Commercial (0°C to 70°C) 45 0.1 AT28C64X-25JI AT28C64X-25PI AT28C64X-25SI AT28C64X-25TI 32J 28P6 28S 28T Industrial (-40°C to 85°C) 200 250 Valid Part Numbers The following table lists standard Atmel products that can be ordered. Device Numbers Speed Package and Temperature Combinations AT28C64 X 12 JC, JI, PC, PI, SC, SI, TC, TI AT28C64 X 15 JC, JI, PC, PI, SC, SI, TC, TI AT28C64 X 20 JC, JI, PC, PI, SC, SI, TC, TI AT28C64 X 25 JC, JI, PC, PI, SC, SI, TC, TI Die Products Reference Section: Parallel EEPROM Die Products Package Type 32J 32-lead, Plastic J-leaded Chip Carrier (PLCC) 28P6 28-lead, 0.600" Wide, Plastic Dull Inline Package (PDIP) 28S 28-lead, 0.300" Wide, Plastic Gull Wing, Small Outline (SOIC) 28T 28-lead, Plastic Thin Small Outline Package (TSOP) 10 AT28C64(X) Operation Range AT28C64(X) Packaging Information 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-016 AE 28P6, 28-lead, 0.600" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-011 AB .045(1.14) X 45˚ PIN NO. 1 IDENTIFY .553(14.0) .547(13.9) .595(15.1) .585(14.9) .032(.813) .026(.660) 1.47(37.3) 1.44(36.6) .025(.635) X 30˚ - 45˚ .012(.305) .008(.203) PIN 1 .530(13.5) .490(12.4) .566(14.4) .530(13.5) .021(.533) .013(.330) .090(2.29) MAX 1.300(33.02) REF .050(1.27) TYP .300(7.62) REF .430(10.9) .390(9.90) AT CONTACT POINTS .030(.762) .015(.381) .095(2.41) .060(1.52) .140(3.56) .120(3.05) .022(.559) X 45˚ MAX (3X) .453(11.5) .447(11.4) .495(12.6) .485(12.3) 28S, 28-lead, 0.300" Wide, Plastic Gull Wing Small Outline (SOIC) Dimensions in Inches and (Millimeters) .220(5.59) MAX .005(.127) MIN SEATING PLANE .065(1.65) .015(.381) .022(.559) .014(.356) .161(4.09) .125(3.18) .110(2.79) .090(2.29) .012(.305) .008(.203) .065(1.65) .041(1.04) .630(16.0) .590(15.0) 0 REF 15 .690(17.5) .610(15.5) 28T, 28-lead, Plastic Thin Small Outline Package (TSOP) Dimensions in Millimeters and (Inches)* INDEX MARK AREA 11.9 (0.469) 11.7 (0.461) 13.7 (0.539) 13.1 (0.516) 0.27 (0.011) 0.18 (0.007) 0.55 (0.022) BSC 7.15 (0.281) REF 8.10 (0.319) 7.90 (0.311) 1.25 (0.049) 1.05 (0.041) 0.20 (0.008) 0.10 (0.004) 0 5 REF 0.20 (0.008) 0.15 (0.006) 0.70 (0.028) 0.30 (0.012) *Controlling dimension: millimeters 11 Atmel Headquarters Atmel Operations Corporate Headquarters Atmel Colorado Springs 2325 Orchard Parkway San Jose, CA 95131 TEL (408) 441-0311 FAX (408) 487-2600 Europe 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL (719) 576-3300 FAX (719) 540-1759 Atmel Rousset Atmel U.K., Ltd. Coliseum Business Centre Riverside Way Camberley, Surrey GU15 3YL England TEL (44) 1276-686-677 FAX (44) 1276-686-697 Zone Industrielle 13106 Rousset Cedex France TEL (33) 4-4253-6000 FAX (33) 4-4253-6001 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369 Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Fax-on-Demand North America: 1-(800) 292-8635 International: 1-(408) 441-0732 e-mail literature@atmel.com Web Site http://www.atmel.com BBS 1-(408) 436-4309 © Atmel Corporation 1999. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. Marks bearing ® and/or ™ are registered trademarks and trademarks of Atmel Corporation. Terms and product names in this document may be trademarks of others. Printed on recycled paper. 0001H–12/99/xM