AT91SAM9M11B-CU

Features • 400 MHz ARM926EJ-S™ ARM® Thumb® Processor – 32 KBytes Data Cache, 32 KBytes Instruction Cache, MMU • Memories • • • • • – 4-port, 4-bank DDR2/LPDDR Controller – External Bus Interface supporting 4-bank DDR2/LPDDR, SDR/LPSDR, Static Memories, CompactFlash®, SLC NAND Flash with ECC – One 64-KByte internal SRAM, single-cycle access at system speed or processor speed through TCM interface – One 64-KByte internal ROM, embedding bootstrap routine Peripherals – Universal Video Decoder provides decoding at up to 30 fps at D1 (720 x 576 pixels) or WVGA (800 x 480) resolution – LCD Controller supporting STN and TFT displays up to 1280*860 – ITU-R BT. 601/656 Image Sensor Interface – Dual High Speed USB Host and a High Speed USB Device with On-Chip Transceivers – 10/100 Mbps Ethernet MAC Controller – Two High Speed Memory Card Hosts (SDIO, SDCard, e.MMC and CE ATA) – AC'97 controller – Two Master/Slave Serial Peripheral Interfaces – Two Three-channel 16-bit Timer/Counters – Two Synchronous Serial Controllers (I2S mode) – Four-channel 16-bit PWM Controller – Two Two-wire Interfaces – Four USARTs with ISO7816, IrDA, Manchester and SPI modes; one DBGU – 8-channel 10-bit ADC with 4-wire Touch Screen support Cryptography – TRNG True Random Number Generator – AES256-, 192-, 128-bit Key Algorithm – TDES Compliant with FIPS PUB 46-3 Specifications – SHA (SHA1 and SHA256) Compliant with FIPS Publication 180-2 System – 133 MHz twelve 32-bit layer AHB Bus Matrix – 39 DMA Channels – Boot from NAND Flash, SDCard, DataFlash® or serial DataFlash – Reset Controller with on-chip Power-on Reset – Selectable 32768 Hz Low-power and 12 MHz Crystal Oscillators – Internal Low-power 32 kHz RC Oscillator – One PLL for the system and one 480 MHz PLL optimized for USB High Speed – Two Programmable External Clock Signals – Advanced Interrupt Controller and Debug Unit – Periodic Interval Timer, Watchdog Timer, Real Time Timer and Real Time Clock I/O – Five 32-bit Parallel Input/Output Controllers – 160 Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os with Schmitt trigger input Package – 324-ball TFBGA, pitch 0.8 mm AT91SAM ARM-based Embedded MPU SAM9M11 Summary NOTE: This is a summary document. The complete document is available under NDA. For more information, please contact your local Atmel sales office. 6437DS–ATARM–23-Apr-13 1. Description The SAM9M11 is a multimedia enabled mid-range ARM926-based embedded MPU running at 400MHz, combining user interfaces, video playback and connectivity. It includes hardware video decoder, LCD Controller, resistive touchscreen, camera interface, audio, Ethernet 10/100 and high speed USB and SDIO. The hardware video decoder supports H.264, MPEG-4, MPEG-2, VC-1, H.263 up to D1 (720 x 576 pixels) or WVGA (800 x 480) resolutions at 30 frames per second (fps). The SAM9M11 also provides hardware image post-processing, such as image scaling, color conversion and image rotation. The SAM9M11 supports the latest generation of DDR2 and NAND Flash memory interfaces for program and data storage. An internal 133 MHz multi-layer bus architecture associated with 39 DMA channels, a dual external bus interface and distributed memory including a 64-KByte SRAM which can be configured as a tightly coupled memory (TCM) sustains the high bandwidth required by the processor and the high speed peripherals. On-chip hardware accelerators with DMA support enable high-speed data encryption and authentication of the transferred data or application. Supported standards are up to 256-bit AES, FIPS PUB 46-3 compliant TDES and FIPS Publication 180-2 compliant SHA1 and SHA256. A True Random Number Generator is embedded for key generation and exchange protocols. The I/Os support 1.8V or 3.3V operation, which are independently configurable for the memory interface and peripheral I/Os. This feature completely eliminates the need for any external level shifters. In addition it supports 0.8 ball pitch package for low cost PCB manufacturing. The SAM9M11 power management controller features efficient clock gating and a battery backup section minimizing power consumption in active and standby modes. The SAM9M11 device is particularly well suited for media-rich displays and control panels in home and commercial buildings, POS terminals, entertainment systems, internet appliances and medical applications. 2 SAM9M11 6437DS–ATARM–23-Apr-13 6437DS–ATARM–23-Apr-13 MCI0/MCI1 SD/SDIO CE ATA FIFO PIOC TWI0 TWI1 PIOE PIOB RSTC PIOD POR VDDCORE RTC PIOA POR SHDC RTT 4 GPBR RC OSC 32K PIT WDT OSC12M VDDBU NRST XIN32 XOUT32 SHDN WKUP PLLA PDC DBGU AIC PLLUTMI PMC PIO XIN XOUT PLLRCA DRXD DTXD FIQ IRQ System Controller JTA GS EL NT R ST TD I TD O TM T S C K RT CK PDC USART0 USART1 USART2 USART3 ROM 64KB SRAM 64KB 4-CH PWM AES I BM TC0 TC1 TC2 PDC TDES D DCache ICache MMU 32Kbytes 32K bytes ITCM DTCM Bus Interface ARM926EJ-S In-Circuit Emulator JTAG / Boundary Scan S PB TC3 TC4 TC5 PDC SHA DMA DMA HS USB DMA LCD PIO SPI0 SPI1 PDC PIO SSC0 SSC1 PDC Peripheral DMA Controller DMA ISI SSC0_, SSC1_ Peripheral Bridge SPI0_, SPI1_ TRNG Multi-Layer AHB Matrix HS EHCI USB HOST PA HS Transceiver AC97 PDC DMA EMAC 8-CH 10Bit ADC TouchScreen PDC Video Decoder + Post Processing 8-CH DMA HF S HH DPA SD ,H P A,HFSD HS MA VB DM G A DF S DH DP/H SD FS P/H DP H B S LC DP ,DFS D B,D DM LC D0 HS /H D -L D F L V C D S S M C D YN D2 /H DM HS B LD DO C,L 3 DM D T C L EN CK DH B C SY DP ,LC NC W DC IS R, I_ C I DO LC S I_ -IS DM IS PCK I_D OD I_ 11 IS HS I _ Y IS VS NC I _M YN C C ET K X ET CK X E EC EN RX R -E C ER S-E TX K E ER XER COL R X ET 0-E ERX X R D E 0-ET X3 V M EM DC X3 DI O HS Transceiver APB Static Memory Controller CF NandFlash Controller ECC DDR2/ LPDDR/ SDRAM Controller EBI DDR2 LPDDR D16-D31 NWAIT DQM[2..3] A19-A24 NCS4/CFCS0 NCS5/CFCS1 A25/CFRNW CFCE1-CFCE2 NCS2 NCS3/NANDCS D0-D15 A0/NBS0 A1/NBS2/NWR2 A2-A15, A18 A16/BA0 A17/BA1 NCS1/SDCS SDCK, #SDCK, SDCK RAS, CAS SDWE, SDA10 DQM[0..1] DQS[0..1] NRD NWR0/NWE NWR1/NBS1 NWR3/NBS3 NCS0 NANDOE, NANDWE DDR_CS DDR_CLK,#DDR_CL DDR_CKE DDR_RAS, DDR_CAS DDR_WE DDR_BA0, DDR_BA1 DDR_A0-DDR_A13 DDR_D0-DDR_D15 DDR_VREF DDR_DQM[0..1] DDR_DQS[0..1] SAM9M11 Block Diagram M C I M 0_D CI 0_ A0M C M DA CI0 C ,M _ M I0_ CI DA C 7 C 1 I 1_ K, _C DA MC DA 0- I1_ M CI CK 1_ DA TW 7 TW D0 C -T K 0- WD CT TW 1 C S RT 0-C K1 S T SC 0-R S3 K T RD 0-S S3 X C TX 0-R K3 D D 0 X PW -TX 3 D3 M 0PW TC M L 3 K TI 0-T O A0 CL T -T K I O IO 2 TC B0 A2 L -T TI K3 IO B O TI A3 TCL 2 O B3 TIO K5 -T A5 IO B NP 5 NP CS C 3 NP S2 NP CS C 1 SP S0 C M K O M SI TK ISO 0 TF -TK TD 0-T 1 F R 0-T 1 D 0 D RF -RD1 0 RK -R 1 0- F1 AC RK1 AC 97C 9 K AC 7F 9 S AC 7RX TS 97 A TX D TR AD IG 0 AD XP 1 A XM D 2Y GP AD AD3 P Y 4 TS -GP M A A DV D7 RE V F D DA GN NA D Figure 2-1. PCK0-PCK1 TST SAM9M11 2. Block Diagram 3 3. Signal Description Table 3-1 gives details on the signal names classified by peripheral. Table 3-1. Signal Description List Signal Name Function Type Active Level Reference Voltage Comments Power Supplies VDDIOM0 DDR2 I/O Lines Power Supply Power 1.65V to 1.95V VDDIOM1 EBI I/O Lines Power Supply Power 1.65V to 1.95V or 3.0V to3.6V VDDIOP0 Peripherals I/O Lines Power Supply Power 1.65V to 3.6V VDDIOP1 Peripherals I/O Lines Power Supply Power 1.65V to 3.6V VDDIOP2 ISI I/O Lines Power Supply Power 1.65V to 3.6V VDDBU Backup I/O Lines Power Supply Power 1.8V to 3.6V VDDANA Analog Power Supply Power 3.0V to 3.6V VDDPLLA PLLA Power Supply Power 0.9V to 1.1V VDDPLLUTMI PLLUTMI Power Supply Power 0.9V to 1.1V VDDOSC Oscillator Power Supply Power 1.65V to 3.6V VDDCORE Core Chip Power Supply Power 0.9V to 1.1V VDDUTMIC UDPHS and UHPHS UTMI+ Core Power Supply Power 0.9V to 1.1V VDDUTMII UDPHS and UHPHS UTMI+ interface Power Supply Power 3.0V to 3.6V GNDIOM DDR2 and EBI I/O Lines Ground Ground GNDIOP Peripherals and ISI I/O lines Ground Ground GNDCORE Core Chip Ground Ground GNDOSC PLLA, PLLUTMI and Oscillator Ground Ground GNDBU Backup Ground Ground GNDUTMI UDPHS and UHPHS UTMI+ Core and interface Ground Ground GNDANA Analog Ground Ground Clocks, Oscillators and PLLs XIN Main Oscillator Input Input XOUT Main Oscillator Output Output XIN32 Slow Clock Oscillator Input Input XOUT32 Slow Clock Oscillator Output Output VBG Bias Voltage Reference for USB Analog PCK0 - PCK1 Programmable Clock Output Output 4 (1) SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Reference Voltage Comments Shutdown, Wakeup Logic SHDN Shut-Down Control Output VDDBU Driven at 0V only. 0: The device is in backup mode 1: The device is running (not in backup mode). WKUP Wake-Up Input Input VDDBU Accept between 0V and VDDBU. ICE and JTAG TCK Test Clock Input VDDIOP0 No pull-up resistor, Schmitt trigger TDI Test Data In Input VDDIOP0 No pull-up resistor, Schmitt trigger TDO Test Data Out Output VDDIOP0 TMS Test Mode Select Input VDDIOP0 No pull-up resistor, Schmitt trigger JTAGSEL JTAG Selection Input VDDBU Pull-down resistor (15 kΩ). RTCK Return Test Clock Output VDDIOP0 Reset/Test VDDIOP0 Open-drain output, Pull-Up resistor (100 kΩ), Schmitt trigger Input VDDBU Pull-down resistor (15 kΩ), Schmitt trigger Test Reset Signal Input VDDIOP0 Pull-Up resistor (100 kΩ), Schmitt trigger Boot Mode Select Input VDDIOP0 must be connected to GND or VDDIOP0. NRST Microcontroller Reset(2) I/O TST Test Mode Select NTRST BMS Low Debug Unit - DBGU DRXD Debug Receive Data Input (1) DTXD Debug Transmit Data Output (1) Advanced Interrupt Controller - AIC IRQ External Interrupt Input Input (1) FIQ Fast Interrupt Input Input (1) PIO Controller - PIOA- PIOB - PIOC - PIOD - PIOE PA0 - PA31 Parallel IO Controller A I/O (1) PB0 - PB31 Parallel IO Controller B I/O (1) Pulled-up input at reset (100kΩ)(3), Schmitt trigger Pulled-up input at reset (100kΩ)(3), Schmitt trigger 5 6437DS–ATARM–23-Apr-13 Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Reference Voltage PC0 - PC31 Parallel IO Controller C I/O (1) PD0 - PD31 Parallel IO Controller D I/O (1) PE0 - PE31 Parallel IO Controller E I/O (1) Comments Pulled-up input at reset (100kΩ)(3), Schmitt trigger Pulled-up input at reset (100kΩ)(3), Schmitt trigger Pulled-up input at reset (100kΩ)(3), Schmitt trigger DDR Memory Interface - DDR2/LPDDR Controller DDR_D0 DDR_D15 Data Bus I/O VDDIOM0 Pulled-up input at reset DDR_A0 DDR_A13 Address Bus Output VDDIOM0 0 at reset DDR_CLK#DDR_CLK DDR differential clock input Output VDDIOM0 DDR_CKE DDR Clock Enable Output High VDDIOM0 DDR_CS DDR Chip Select Output Low VDDIOM0 DDR_WE DDR Write Enable Output Low VDDIOM0 DDR_RASDDR_CAS Row and Column Signal Output Low VDDIOM0 DDR_DQM[0..1] Write Data Mask Output VDDIOM0 DDR_DQS[0..1] Data Strobe Output VDDIOM0 DDR_BA0 DDR_BA1 Bank Select Output VDDIOM0 DDR_VREF Reference Voltage Input VDDIOM0 External Bus Interface - EBI D0 -D31 Data Bus I/O VDDIOM1 Pulled-up input at reset A0 - A25 Address Bus Output VDDIOM1 0 at reset NWAIT External Wait Signal Input Low VDDIOM1 EBI - Static Memory Controller - SMC NCS0 - NCS5 Chip Select Lines Output Low VDDIOM1 NWR0 - NWR3 Write Signal Output Low VDDIOM1 NRD Read Signal Output Low VDDIOM1 NWE Write Enable Output Low VDDIOM1 NBS0 - NBS3 Byte Mask Signal Output Low VDDIOM1 EBI - CompactFlash Support CFCE1 - CFCE2 CompactFlash Chip Enable Output Low VDDIOM1 CFOE CompactFlash Output Enable Output Low VDDIOM1 CFWE CompactFlash Write Enable Output Low VDDIOM1 CFIOR CompactFlash IO Read Output Low VDDIOM1 6 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Table 3-1. Signal Description List (Continued) Signal Name Function Type CFIOW CompactFlash IO Write Output CFRNW CompactFlash Read Not Write Output CFCS0 -CFCS1 CompactFlash Chip Select Lines Output Active Level Low Reference Voltage Comments VDDIOM1 VDDIOM1 Low VDDIOM1 EBI - NAND Flash Support NANDCS NAND Flash Chip Select Output Low VDDIOM1 NANDOE NAND Flash Output Enable Output Low VDDIOM1 NANDWE NAND Flash Write Enable Output Low VDDIOM1 EBI - DDR2/SDRAM/LPDDR Controller SDCK,#SDCK DDR2/SDRAM differential clock Output VDDIOM1 SDCKE DDR2/SDRAM Clock Enable Output High VDDIOM1 SDCS DDR2/SDRAM Controller Chip Select Output Low VDDIOM1 BA0 - BA1 Bank Select Output SDWE DDR2/SDRAM Write Enable Output Low VDDIOM1 RAS - CAS Row and Column Signal Output Low VDDIOM1 SDA10 SDRAM Address 10 Line Output VDDIOM1 DQS[0..1] Data Strobe Output VDDIOM1 DQM[0..3] Write Data Mask Output VDDIOM1 VDDIOM1 High Speed Multimedia Card Interface - HSMCIx MCIx_CK Multimedia Card Clock I/O (1) MCIx_CDA Multimedia Card Slot A Command I/O (1) MCIx_DA0 MCIx_DA7 Multimedia Card Slot A Data I/O (1) Universal Synchronous Asynchronous Receiver Transmitter - USARTx SCKx USARTx Serial Clock I/O (1) TXDx USARTx Transmit Data Output (1) RXDx USARTx Receive Data Input (1) RTSx USARTx Request To Send Output (1) CTSx USARTx Clear To Send Input (1) Synchronous Serial Controller - SSCx TDx SSC Transmit Data Output (1) RDx SSC Receive Data Input (1) TKx SSC Transmit Clock I/O (1) RKx SSC Receive Clock I/O (1) TFx SSC Transmit Frame Sync I/O (1) RFx SSC Receive Frame Sync I/O (1) 7 6437DS–ATARM–23-Apr-13 Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Reference Voltage Comments AC97 Controller - AC97C AC97RX AC97 Receive Signal Input (1) AC97TX AC97 Transmit Signal Output (1) AC97FS AC97 Frame Synchronization Signal Output (1) AC97CK AC97 Clock signal Input (1) Time Counter - TCx TCLKx TC Channel x External Clock Input Input (1) TIOAx TC Channel x I/O Line A I/O (1) TIOBx TC Channel x I/O Line B I/O (1) Pulse Width Modulation Controller - PWM PWMx Pulse Width Modulation Output (1) Output Serial Peripheral Interface - SPIx_ SPIx_MISO Master In Slave Out I/O (1) SPIx_MOSI Master Out Slave In I/O (1) SPIx_SPCK SPI Serial Clock I/O (1) SPIx_NPCS0 SPI Peripheral Chip Select 0 I/O Low (1) SPIx_NPCS1SPIx_NPCS3 SPI Peripheral Chip Select Output Low (1) Two-Wire Interface TWDx Two-wire Serial Data I/O (1) TWCKx Two-wire Serial Clock I/O (1) USB Host High Speed Port - UHPHS HFSDPA USB Host Port A Full Speed Data + Analog VDDUTMII HFSDMA USB Host Port A Full Speed Data - Analog VDDUTMII HHSDPA USB Host Port A High Speed Data + Analog VDDUTMII HHSDMA USB Host Port A High Speed Data - Analog VDDUTMII HFSDPB USB Host Port B Full Speed Data + Analog VDDUTMII Multiplexed with DFSDP HFSDMB USB Host Port B Full Speed Data - Analog VDDUTMII Multiplexed with DFSDM HHSDPB USB Host Port B High Speed Data + Analog VDDUTMII Multiplexed with DHSDP HHSDMB USB Host Port B High Speed Data - Analog VDDUTMII Multiplexed with DHSDM USB Device High Speed Port - UDPHS DFSDM USB Device Full Speed Data - Analog VDDUTMII DFSDP USB Device Full Speed Data + Analog VDDUTMII DHSDM USB Device High Speed Data - Analog VDDUTMII DHSDP USB Device High Speed Data + Analog VDDUTMII 8 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Reference Voltage Comments Ethernet 10/100 ETXCK ERXCK Transmit Clock or Reference Clock Receive Clock Input (1) MII only, REFCK in RMII Input (1) MII only ETXEN Transmit Enable Output (1) ETX0-ETX3 Transmit Data Output (1) ETX0-ETX1 only in RMII Output (1) MII only Input (1) RXDV in MII, CRSDV in RMII ERX0-ERX1 only in RMII ETXER ERXDV Transmit Coding Error Receive Data Valid ERX0-ERX3 Receive Data Input (1) ERXER Receive Error Input (1) ECRS Carrier Sense and Data Valid Input (1) MII only Input (1) MII only ECOL Collision Detect EMDC Management Data Clock Output (1) EMDIO Management Data Input/Output I/O (1) Image Sensor Interface ISI_D0-ISI_D11 Image Sensor Data Input VDDIOP2 ISI_MCK Image sensor Reference clock output VDDIOP2 ISI_HSYNC Image Sensor Horizontal Synchro input VDDIOP2 ISI_VSYNC Image Sensor Vertical Synchro input VDDIOP2 ISI_PCK Image Sensor Data clock input VDDIOP2 LCD Controller - LCDC LCDD0 LCDD23 LCD Data Bus Output VDDIOP1 LCDVSYNC LCD Vertical Synchronization Output VDDIOP1 LCDHSYNC LCD Horizontal Synchronization Output VDDIOP1 LCDDOTCK LCD Dot Clock Output VDDIOP1 LCDDEN LCD Data Enable Output VDDIOP1 LCDCC LCD Contrast Control Output VDDIOP1 LCDPWR LCD panel Power enable control Output VDDIOP1 LCDMOD LCD Modulation signal Output VDDIOP1 Touch Screen Analog-to-Digital Converter AD0XP Analog input channel 0 or Touch Screen Top channel Analog VDDANA Multiplexed with AD0 AD1XM Analog input channel 1 or Touch Screen Bottom channel Analog VDDANA Multiplexed with AD1 AD2YP Analog input channel 2 or Touch Screen Right channel Analog VDDANA Multiplexed with AD2 9 6437DS–ATARM–23-Apr-13 Table 3-1. Signal Description List (Continued) Signal Name Function Type Active Level Reference Voltage Comments Multiplexed with AD3 AD3YM Analog input channel 3 or Touch Screen Left channel Analog VDDANA GPAD4-GPAD7 Analog Inputs Analog VDDANA TSADTRG ADC Trigger Input VDDANA TSADVREF ADC Reference Analog VDDANA Notes: 1. Refer to peripheral multiplexing tables in Section 9.4 “Peripheral Signals Multiplexing on I/O Lines” for these signals. 2. When configured as an input, the NRST pin enables asynchronous reset of the device when asserted low. This allows connection of a simple push button on the NRST pin as a system-user reset. 3. Programming of this pull-up resistor is performed independently for each I/O line through the PIO Controllers. After reset, all the I/O lines default as inputs with pull-up resistors enabled, except those which are multiplexed with the External Bus Interface signals that require to be enabled as Peripheral at reset. This is explicitly indicated in the column “Reset State” of the peripheral multiplexing tables. 10 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 4. Package and Pinout The SAM9M11 is delivered in a 324-ball LFBGA package. 4.1 Mechanical Overview of the 324-ball LFBGA Package Figure 4-1 shows the orientation of the 324-ball LFBGA Package Figure 4-1. Orientation of the 324-ball LFBGA Package Bottom VIEW V U T R P N M L K J H G F E D C B A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 11 6437DS–ATARM–23-Apr-13 4.2 324-ball TFBGA Package Pinout Table 4-1. Pin A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 12 SAM9M11 Pinout for 324-ball BGA Package Signal Name PC27 PC28 PC25 PC20 PC12 PC7 PC5 PC0 NWR3/NBS3 NCS0 DQS0 RAS SDCK NSDCK D7 DDR_VREF D0 A14 PC31 PC29 PC30 PC22 PC17 PC10 PC11 PC2 SDA10 A17/BA1 DQM0 SDCKE D12 D8 D4 D3 A15 A13 XIN32 GNDANA WKUP PC26 PC21 PC15 PC9 PC3 NWR0/NWE A16/BA0 CAS D15 Pin E10 E11 E12 E13 E14 E15 E16 E17 E18 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 G13 G14 G15 G16 G17 G18 H1 H2 H3 Signal Name NANDWE DQS1 D13 D11 A4 A8 A9 A7 VDDCORE PD22 PD24 SHDN PE1 PE3 VDDIOM1 PC19 PC14 PC4 NCS1/SDCS NRD SDWE A0/NBS0 A1/NBS2/NWR2 A3 A6 A5 A2 PD25 PD23 PE6 PE0 PE2 PE8 PE4 PE11 GNDCORE VDDIOM1 VDDIOM1 VDDCORE VDDCORE DDR_DQM0 DDR_DQS1 DDR_BA1 DDR_BA0 DDR_DQS0 PD26 PD27 VDDIOP1 Pin K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 K12 K13 K14 K15 K16 K17 K18 L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 L15 L16 L17 L18 M1 M2 M3 M4 M5 M6 M7 M8 M9 M10 M11 M12 Signal Name PE21 PE23 PE26 PE22 PE24 PE25 PE27 PE28 VDDIOP0 VDDIOP0 GNDIOM GNDIOM VDDIOM0 DDR_A7 DDR_A8 DDR_A9 DDR_A11 DDR_A10 PA0 PE30 PE29 PE31 PA2 PA4 PA8 PD2 PD13 PD29 PD31 VDDIOM0 VDDIOM0 DDR_A1 DDR_A3 DDR_A4 DDR_A6 DDR_A5 PA1 PA5 PA6 PA7 PA10 PA14 PB14 PD4 PD15 NRST PB11 PB25 Pin P10 P11 P12 P13 P14 P15 P16 P17 P18 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17 T18 U1 U2 U3 Signal Name TMS VDDPLLA PB20 PB31 DDR_D7 DDR_D3 DDR_D4 DDR_D5 DDR_D10 PA18 PA20 PA24 PA30 PB4 PB13 PD0 PD9 PD18 TDI RTCK PB22 PB29 DDR_D6 DDR_D1 DDR_D0 HHSDMA HFSDMA PA22 PA25 PA26 PB0 PB6 PB16 PD1 PD11 PD19 PD30 BMS PB8 PB30 DDR_D2 PB21 PB23 HHSDPA HFSDPA PA27 PA29 PA28 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Table 4-1. Pin C13 C14 C15 C16 C17 C18 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 E1 E2 E3 E4 E5 E6 E7 E8 E9 SAM9M11 Pinout for 324-ball BGA Package (Continued) Signal Name D10 D6 D2 GNDIOM A18 A12 XOUT32 PD20 GNDBU VDDBU PC24 PC18 PC13 PC6 NWR1/NBS1 NANDOE DQM1 D14 D9 D5 D1 VDDIOM1 A11 A10 PD21 TSADVREF VDDANA JTAGSEL TST PC23 PC16 PC8 PC1 Pin H4 H5 H6 H7 H8 H9 H10 H11 H12 H13 H14 H15 H16 H17 H18 J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J16 J17 J18 Signal Name PE13 PE5 PE7 PE9 PE10 GNDCORE GNDIOP VDDCORE GNDIOM GNDIOM DDR_CS DDR_WE DDR_DQM1 DDR_CAS DDR_NCLK PE19 PE16 PE14 PE15 PE12 PE17 PE18 PE20 GNDCORE GNDCORE GNDIOP GNDIOM GNDIOM DDR_A12 DDR_A13 DDR_CKE DDR_RAS DDR_CLK Pin M13 M14 M15 M16 M17 M18 N1 N2 N3 N4 N5 N6 N7 N8 N9 N10 N11 N12 N13 N14 N15 N16 N17 N18 P1 P2 P3 P4 P5 P6 P7 P8 P9 Signal Name PB27 VDDIOM0 DDR_D14 DDR_D15 DDR_A0 DDR_A2 PA3 PA9 PA12 PA15 PA16 PA17 PB18 PD6 PD16 NTRST PB9 PB24 PB28 DDR_D13 DDR_D8 DDR_D9 DDR_D11 DDR_D12 PA11 PA13 PA19 PA21 PA23 PB12 PB19 PD8 PD28 Pin U4 U5 U6 U7 U8 U9 U10 U11 U12 U13 U14 U15 U16 U17 U18 V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 V15 V16 V17 V18 Signal Name PB3 PB7 PB17 PD7 PD10 PD14 TCK VDDOSC GNDOSC PB10 PB26 HHSDPB/DHSDP HHSDMB/DHSDM GNDUTMI VDDUTMIC PA31 PB1 PB2 PB5 PB15 PD3 PD5 PD12 PD17 TDO XOUT XIN VDDPLLUTMI VDDIOP2 HFSDPB/DFSDP HFSDMB/DFSDM VDDUTMII VBG 13 6437DS–ATARM–23-Apr-13 5. Power Considerations 5.1 Power Supplies The SAM9M11 has several types of power supply pins: • VDDCORE pins: Power the core, including the processor, the embedded memories and the peripherals; voltage ranges from 0.9V to 1.1V, 1.0V typical. • VDDIOM0 pins: Power the DDR2/LPDDR I/O lines; voltage ranges between 1.65V and 1.95V (1.8V typical). • VDDIOM1 pins: Power the External Bus Interface 1 I/O lines; voltage ranges between 1.65V and 1.95V (1.8V typical) or between 3.0V and 3.6V (3.3V typical). • VDDIOP0, VDDIOP1, VDDIOP2 pins: Power the Peripherals I/O lines; voltage ranges from 1.65V to 3.6V. • VDDBU pin: Powers the Slow Clock oscillator, the internal RC oscillator and a part of the System Controller; voltage ranges from 1.8V to 3.6V. • VDDPLLUTMI Powers the PLLUTMI cell; voltage range from 0.9V to 1.1V. • VDDUTMIC pin: Powers the USB device and host UTMI+ core; voltage range from 0.9V to 1.1V, 1.0V typical. • VDDUTMII pin: Powers the USB device and host UTMI+ interface; voltage range from 3.0V to 3.6V, 3.3V typical. • VDDPLLA pin: Powers the PLLA cell; voltage ranges from 0.9V to 1.1V. • VDDOSC pin: Powers the Main Oscillator cells; voltage ranges from 1.65V to 3.6V • VDDANA pin: Powers the Analog to Digital Converter; voltage ranges from 3.0V to 3.6V, 3.3V typical. Some supply pins share common ground (GND) pins whereas others have separate grounds. The respective power/ground pin assignments are as follows: 14 VDDCORE GNDCORE VDDIOM0, VDDIOM1 GNDIOM VDDIOP0, VDDIOP1, VDDIOP2 GNDIOP VDDBU GNDBU VDDUTMIC, VDDUTMII GNDUTMI VDDPLLUTMI, VDDPLLA, VDDOSC, GNDOSC VDDANA GNDANA SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 6. Processor and Architecture 6.1 ARM926EJ-S Processor • RISC Processor Based on ARM v5TEJ Architecture with DSP Instruction Extensions and Jazelle® technology for Java® acceleration • Two Instruction Sets – ARM High-performance 32-bit Instruction Set – Thumb High Code Density 16-bit Instruction Set • 5-Stage Pipeline Architecture: – Instruction Fetch (F) – Instruction Decode (D) – Execute (E) – Data Memory (M) – Register Write (W) • 32-KByte Data Cache, 32-KByte Instruction Cache – Virtually-addressed 4-way Associative Cache – Eight words per line – Write-through and Write-back Operation – Pseudo-random or Round-robin Replacement • Write Buffer – Main Write Buffer with 16-word Data Buffer and 4-address Buffer – DCache Write-back Buffer with 8-word Entries and a Single Address Entry – Software Control Drain • Standard ARM v4 and v5 Memory Management Unit (MMU) – Access Permission for Sections – Access Permission for large pages and small pages can be specified separately for each quarter of the page – 16 embedded domains • Bus Interface Unit (BIU) – Arbitrates and Schedules AHB Requests – Separate Masters for both instruction and data access providing complete Matrix system flexibility – Separate Address and Data Buses for both the 32-bit instruction interface and the 32-bit data interface – On Address and Data Buses, data can be 8-bit (Bytes), 16-bit (Half-words) or 32-bit (Words) • TCM Interface 15 6437DS–ATARM–23-Apr-13 6.2 Bus Matrix • 12-layer Matrix, handling requests from 11 masters • Programmable Arbitration strategy – Fixed-priority Arbitration – Round-Robin Arbitration, either with no default master, last accessed default master or fixed default master • Burst Management – Breaking with Slot Cycle Limit Support – Undefined Burst Length Support • One Address Decoder provided per Master – Three different slaves may be assigned to each decoded memory area: one for internal ROM boot, one for internal flash boot, one after remap • Boot Mode Select – Non-volatile Boot Memory can be internal ROM or external memory on EBI_NCS0 – Selection is made by General purpose NVM bit sampled at reset • Remap Command – Allows Remapping of an Internal SRAM in Place of the Boot Non-Volatile Memory (ROM or External Flash) – Allows Handling of Dynamic Exception Vectors 6.2.1 Matrix Masters The Bus Matrix of the SAM9M11 manages Masters, thus each master can perform an access concurrently with others, depending on whether the slave it accesses is available. Each Master has its own decoder, which can be defined specifically for each master. In order to simplify the addressing, all the masters have the same decodings. Table 6-1. 16 List of Bus Matrix Masters Master 0 ARM926™ Instruction Master 1 ARM926 Data Master 2 Peripheral DMA Controller (PDC) Master 3 USB HOST OHCI Master 4 DMA Master 5 DMA Master 6 ISI Controller DMA Master 7 LCD DMA Master 8 Ethernet MAC DMA Master 9 USB Device High Speed DMA Master 10 USB Host High Speed EHCI DMA Master 11 Video Decoder SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 6.2.2 Matrix Slaves Each Slave has its own arbiter, thus allowing a different arbitration per Slave to be programmed. Table 6-2. Slave 0 List of Bus Matrix Slaves Internal SRAM Internal ROM USB OHCI USB EHCI Slave 1 UDP High Speed RAM LCD User Interface Video Decoder 6.2.3 Slave 2 DDR Port 0 Slave 3 DDR Port 1 Slave 4 DDR Port 2 Slave 5 DDR Port 3 Slave 6 External Bus Interface Slave 7 Internal Peripherals Masters to Slaves Access All the Masters can normally access all the Slaves. However, some paths do not make sense, such as allowing access from the Ethernet MAC to the internal peripherals. Thus, these paths are forbidden or simply not wired, and shown as “-” in the following tables. The four DDR ports are connected differently according to the application device. The user can disable the Video Decoder in the Video Mode Configuration Register (bit VDEC_SEL) in the Chip Configuration User Interface. • When the Video Decoder is not enabled (VDEC_SEL=0), the ARM instruction and data are respectively connected to DDR Port 0 and DDR Port 1. The other masters share DDR Port 2 and DDR Port 3. • When the Video Decoder is enabled (VDEC_SEL=1), DDR Port 0 is dedicated to the video controller, and DDR Port 1 to the LCD controller. The remaining masters share DDR Port 2 and DDR Port 3. 17 6437DS–ATARM–23-Apr-13 Figure 6-1. Video Mode Configuration VDEC_EN Video Decoder LCD + Post Processing DMA DDR_S0 ARM I DDR_S1 ARM I ARM D ARM D VDEC_EN DDR_S2 MATRIX DDR_S3 Table 6-3. Master 0 1 ARM 926 Instr. Internal SRAM 0 SAM9M11 Masters to Slaves Access with VDEC_SEL = 0 2 3 4&5 6 7 8 9 10 11 ARM 926 Data PDC USB Host OHCI DMA ISI DMA LCD DMA Ethernet MAC USB Device HS USB Host EHCI VDEC X X X X X X - X X X - Internal ROM X X X - - - - - X - - UHP OHCI X X - - - - - - - - - UHP EHCI X X - - - - - - - - - LCD User Int. X X - - - - - - - - - UDPHS RAM X X - - - - - - - - - 1 VDEC X X - - - - - - - - - 2 DDR Port 0 X - - - - - - - - - - 3 DDR Port 1 - X - - - - - - - - - 4 DDR Port 2 - - X X X X - X X X X 5 DDR Port 3 - - X X X X X X X X - 6 EBI X X X X X X X X X X X 7 Internal Periph. X X X - X - - - - - - Slave 0 18 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Table 6-4. 4&5 6 7 8 9 10 11 PDC USB HOST OHCI DMA ISI DMA LCD DMA Ethern et MAC USB Device HS USB Host EHCI VDEC X X X X X - X X X - X X X - - - - - X - - UHP OHCI X X - - - - - - - - - UHP EHCI X X - - - - - - - - - LCD User Int. X X - - - - - - - - - UDPHS RAM X X - - - - - - - - - VDEC X X - - - - - - - - - 2 DDR Port 0 - - - - - - - - - - X 3 DDR Port 1 - - - - - - X - - - - 4 DDR Port 2 X - X X X X - X X X - 5 DDR Port 3 - X X X X X - X X X - 6 EBI X X X X X X X X X X X 7 Internal Periph. X X X - X - - - - - - 0 Master 0 1 Slave ARM 926 Instr. Internal SRAM 0 SAM9M11 Masters to Slaves Access with VDEC_SEL = 1 (default) 2 3 ARM 926 Data X Internal ROM 1 Table 6-5 summarizes the Slave Memory Mapping for each connected Master, depending on the Remap status (RCBx bit in Bus Matrix Master Remap Control Register MATRIX_MRCR) and the BMS state at reset. Table 6-5. Internal Memory Mapping Master 6.3 RCBx = 0 Slave Base Address BMS = 1 BMS = 0 0x0000 0000 Internal ROM EBI NCS0 RCBx = 1 Internal SRAM Peripheral DMA Controller (PDC) • Acting as one AHB Bus Matrix Master • Allows data transfers from/to peripheral to/from any memory space without any intervention of the processor. • Next Pointer support, prevents strong real-time constraints on buffer management. 19 6437DS–ATARM–23-Apr-13 The Peripheral DMA Controller handles transfer requests from the channel according to the following priorities (Low to High priorities): Table 6-6. 6.4 Peripheral DMA Controller Instance name Channel T/R DBGU Transmit USART3 Transmit USART2 Transmit USART1 Transmit USART0 Transmit AC97 Transmit SPI1 Transmit SPI0 Transmit SSC1 Transmit SSC0 Transmit TSDAC Receive DBGU Receive USART3 Receive USART2 Receive USART1 Receive USART0 Receive AC97 Receive SPI1 Receive SPI0 Receive SSC1 Receive SSC0 Receive USB The SAM9M11 features USB communication ports as follows: • 2 Ports USB Host full speed OHCI and High speed EHCI • 1 Device High speed USB Host Port A is directly connected to the first UTMI transceiver. The Host Port B is multiplexed with the USB device High speed and connected to the second UTMI port. The selection between Host Port B and USB device high speed is controlled by a the bit UDPHS enable bit located in the UDPHS_CTRL control register. 20 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Figure 6-2. USB Selection HS Transceiver HS Transceiver EN_UDPHS 0 PA PB HS EHCI FS OHCI DMA 6.5 1 HS USB DMA DMA Controller • Two Masters • Embeds 8 channels • 64 bytes/FIFO for Channel Buffering • Linked List support with Status Write Back operation at End of Transfer • Word, HalfWord, Byte transfer support. • memory to memory transfer • Peripheral to memory • Memory to peripheral The DMA controller can handle the transfer between peripherals and memory and so receives the triggers from the peripherals below. The hardware interface numbers are also given below in Table Table 6-7. DMA Channel Definition Instance Name T/R DMA Channel HW interface Number MCI0 TX/RX 0 SPI0 TX 1 SPI0 RX 2 SPI1 TX 3 SPI1 RX 4 SSC0 TX 5 SSC0 RX 6 SSC1 TX 7 SSC1 RX 8 AC97 TX 9 AC97 RX 10 MCI1 TX/RX 13 21 6437DS–ATARM–23-Apr-13 6.6 Debug and Test Features • ARM926 Real-time In-circuit Emulator – Two real-time Watchpoint Units – Two Independent Registers: Debug Control Register and Debug Status Register – Test Access Port Accessible through JTAG Protocol – Debug Communications Channel • Debug Unit – Two-pin UART – Debug Communication Channel Interrupt Handling – Chip ID Register • IEEE1149.1 JTAG Boundary-scan on All Digital Pins. 22 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 7. Memories Figure 7-1. SAM9M11 Memory Mapping Address Memory Space Internal Memory Mapping 0x0000 0000 0x0000 0000 0x0010 0000 Internal Memories 256M Bytes 0x0020 0000 Notes: (1) Can be ROM, EBI1_NCS0 or SRAM 0x0030 0000 depending on BMS and REMAP (2) Software programmable 0x0FFF FFFF 0x1000 0000 EBI Chip Select 0 0x0070 0000 256M Bytes 0xF000 0000 0x2FFF FFFF 256M Bytes 256M Bytes 1 MBytes UDPHS RAM UHP OHCI 1 MBytes UHP EHCI 1 MBytes VDEC 1 MBytes 0x00A0 0000 UDPHS 16K Bytes TCO, TC1, TC2 16K Bytes MCI0 16K Bytes TWI0 16K Bytes TWI1 16K Bytes 1 MBytes 1 MBytes Undefined (Abort) 0x0FFF FFFF 0xFFF8 0000 0x4FFF FFFF 0x6FFF FFFF 1 MBytes ROM 0xFFF7 C000 EBI Chip Select 3/ NANDFlash 0x5FFF FFFF SRAM LCD User Interface 0xFFF7 8000 0x4000 0000 0x6000 0000 1 MBytes 0x0090 0000 Reserved 0x3FFF FFFF 0x5000 0000 0x0080 0000 Peripheral Mapping 0x3000 0000 EBI Chip Select 2 1 MBytes DTCM(2) 0x0050 0000 256M Bytes 0x0060 0000 EBI Chip Select 1/ DDRSDRC1 ITCM(2) 0x0040 0000 0x1FFF FFFF 0x2000 0000 1 MBytes Boot Memory (1) EBI Chip Select 4/ Compact Flash Slot 0 EBI Chip Select 5/ Compact Flash Slot 1 0xFFF8 4000 256M Bytes 0xFFF8 8000 256M Bytes USART0 16K Bytes USART1 16K Bytes USART2 16K Bytes Reserved 0xFFF9 0000 0x7000 0000 DDRSDRC0 Chip Select System Controller Mapping 0xFFFF C000 0xFFF8 C000 256M Bytes 0x7FFF FFFF 0x8000 0000 0xFFFF E200 0xFFF9 4000 0xFFF9 8000 USART3 16K Bytes SSC0 16K Bytes SSC1 16K Bytes 0xFFFA 4000 SPI0 16K Bytes SPI1 16K Bytes 0xFFFA 8000 MATRIX 512 Bytes DMAC 512 bytes DBGU 512 Bytes AIC 512 Bytes PIOA 512 Bytes PIOB 512 Bytes PIOC 512 Bytes PIOD 512 bytes PIOE 512 bytes PMC 256 Bytes 0xFFFF F200 AC97 16K Bytes TSADC 16K Bytes ISI 16K Bytes PWMC 16K Bytes EMAC 16K Bytes AES 16K Bytes TDES 16K Bytes 0xFFFB C000 0xFFFC 0000 0xFFFF F400 0xFFFF F600 0xFFFF F800 0xFFFF FA00 0xFFFF FC00 0xFFFF FD00 0xFFFC 4000 RSTC 16 Bytes SHDC 16 Bytes RTTC 16 Bytes PITC 16 Bytes 0xFFFF FD10 0xFFFC 8000 SHA 16K Bytes TRNG 16K Bytes 0xFFFC C000 0xFFFF FD20 0xFFFF FD30 0xFFFF FD40 0xFFFF FD50 0xFFFD 0000 MCI1 16K Bytes 0xFFFF FD60 TC3, TC4, TC5 16K Bytes 0xFFFF FD70 0xFFFD 4000 0xFFFF FFFF 512 Bytes 0xFFFF EE00 0xFFFB 4000 256M Bytes 512 Bytes SMC 0xFFFF EC00 0xFFFB 8000 Internal Peripherals DDRSDRC0 0xFFFF EA00 0xFFFB 0000 0xEFFF FFFF 512 Bytes 0xFFFF F000 0xFFFA C000 0xF000 0000 DDRSDRC1 0xFFFF E800 0xFFFA 0000 1,792M Bytes 512 Bytes 0xFFFF E600 0xFFF9 C000 Undefined (Abort) ECC 0xFFFF E400 0xFFFD 8000 WDTC 16 Bytes SCKCR 16 Bytes GPBR 16 Bytes Reserved 0xFFFF FDB0 Reserved 0xFFFF C000 SYSC 0xFFFF FDC0 0xFFFF FFFF RTCC 16 Bytes Reserved 0xFFFF FFFF 23 6437DS–ATARM–23-Apr-13 7.1 Memory Mapping A first level of address decoding is performed by the AHB Bus Matrix, i.e., the implementation of the Advanced High performance Bus (AHB) for its Master and Slave interfaces with additional features. Decoding breaks up the 4 Gbytes of address space into 16 banks of 256 Mbytes. The banks 1 to 6 are directed to the EBI that associates these banks to the external chip selects NCS0 to NCS5. The bank 7 is directed to the DDRSDRC0 that associates this bank to DDR_NCS chip select and so dedicated to the 4-port DDR2/ LPDDR controller. The bank 0 is reserved for the addressing of the internal memories, and a second level of decoding provides 1 Mbyte of internal memory area. The bank 15 is reserved for the peripherals and provides access to the Advanced Peripheral Bus (APB). Other areas are unused and performing an access within them provides an abort to the master requesting such an access. 7.2 7.2.1 Embedded Memories Internal SRAM The SAM9M11 product embeds a total of 64 Kbytes high-speed SRAM split in 4 blocks of 16 KBytes connected to one slave of the matrix. After reset and until the Remap Command is performed, the four SRAM blocks are contiguous and only accessible at address 0x00300000. After Remap, the SRAM also becomes available at address 0x0. Figure 7-2. Internal SRAM Reset RAM RAM Remap 64K 64K 0x00300000 0x00000000 The SAM9M11 device embeds two memory features. The processor Tightly Coupled Memory Interface (TCM) that allows the processor to access the memory up to processor speed (PCK) and the interface on the AHB side allowing masters to access the memory at AHB speed (MCK). A wait state is necessary to access the TCM at 400 MHz. Setting the bit NWS_TCM in the bus Matrix TCM Configuration Register of the matrix inserts a wait state on the ITCM and DTCM accesses. 7.2.2 TCM Interface On the processor side, this Internal SRAM can be allocated to two areas. 24 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 • Internal SRAM A is the ARM926EJ-S Instruction TCM. The user can map this SRAM block anywhere in the ARM926 instruction memory space using CP15 instructions and the TCR configuration register located in the Chip Configuration User Interface. This SRAM block is also accessible by the ARM926 Masters and by the AHB Masters through the AHB bus • Internal SRAM B is the ARM926EJ-S Data TCM. The user can map this SRAM block anywhere in the ARM926 data memory space using CP15 instructions. This SRAM block is also accessible by the ARM926 Data Master and by the AHB Masters through the AHB bus. • Internal SRAM C is only accessible by all the AHB Masters. After reset and until the Remap Command is performed, this SRAM block is accessible through the AHB bus at address 0x0030 0000 by all the AHB Masters. After Remap, this SRAM block also becomes accessible through the AHB bus at address 0x0 by the ARM926 Instruction and the ARM926 Data Masters. Within the 64 Kbyte SRAM size available, the amount of memory assigned to each block is software programmable according to Table 7-1. Table 7-1. ITCM and DTCM Memory Configuration SRAM A ITCM size (KBytes) seen at 0x100000 through AHB SRAM B DTCM size (KBytes) seen at 0x200000 through AHB SRAM C (KBytes) seen at 0x300000 through AHB 0 0 64 0 64 0 32 32 0 7.2.3 Internal ROM The SAM9M11 embeds an Internal ROM, which contains the bootrom and SAM-BA program. At any time, the ROM is mapped at address 0x0040 0000. It is also accessible at address 0x0 (BMS =1) after the reset and before the Remap Command. 7.2.4 Boot Strategies The system always boots at address 0x0. To ensure maximum boot possibilities the memory layout can be changed with two parameters. REMAP allows the user to layout the internal SRAM bank to 0x0 to ease the development. This is done by software once the system has boot. BMS allows the user to lay out to 0x0, when convenient, the ROM or an external memory. This is done by a hardware way at reset. Note: All the memory blocks can always be seen at their specified base addresses that are not concerned by these parameters. The SAM9M11 Bus Matrix manages a boot memory that depends on the level on the pin BMS at reset. The internal memory area mapped between address 0x0 and 0x000F FFFF is reserved to this effect. If BMS is detected at 1, the boot memory is the embedded ROM. If BMS is detected at 0, the boot memory is the memory connected on the Chip Select 0 of the External Bus Interface. 25 6437DS–ATARM–23-Apr-13 7.2.4.1 BMS = 1, boot on embedded ROM The system boots on Boot Program. • Boot on on-chip RC • Enable the 32768 Hz oscillator • Auto baudrate detection • Downloads and runs an application from external storage media into internal SRAM • Downloaded code size depends on embedded SRAM size • Automatic detection of valid application • Bootloader on a non-volatile memory – SPI DataFlash/SerialFlash connected on NPCS0 of the SPI0 – SDCard – NandFlash – EEPROM connected on TWI0 • SAM-BA Boot in case no valid program is detected in external NVM, supporting – Serial communication on a DBGU – USB Device HS Port 7.2.4.2 BMS = 0, boot on external memory • Boot on on-chip RC • Boot with the default configuration for the Static Memory Controller, byte select mode, 16-bit data bus, Read/Write controlled by Chip Select, allows boot on 16-bit non-volatile memory. For optimization purpose, nothing else is done. To speed up the boot sequence user programmed software should perform a complete configuration: • Enable the 32768 Hz oscillator if best accuracy needed • Program the PMC (main oscillator enable or bypass mode) • Program and Start the PLL • Reprogram the SMC setup, cycle, hold, mode timings registers for EBI CS0 to adapt them to the new clock • Switch the main clock to the new value 7.3 External Memories The SAM9M11 features a Multi-port DDR2 Interface and an External Bus Interface allowing to connect to a wide range of external memories and to any parallel peripheral. 7.3.1 DDRSDRC0 Multi-port DDRSDR Controller Four AHB Interfaces, Management of All Accesses Maximizes Memory Bandwidth and Minimizes Transaction Latency. • Supports AHB Transfers: – Word, Half Word, Byte Access. • Supports DDR2, LPDDR • Numerous Configurations Supported – 2K, 4K, 8K, 16K Row Address Memory Parts 26 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 – DDR2 with Four Internal Banks – DDR2/LPDDR with 16-bit Data Path – One Chip Select for DDR2/LPDDR Device (256 Mbytes Address Space) • Programming Facilities – Multibank Ping-pong Access (Up to 4 Banks Opened at Same Time = Reduces Average Latency of Transactions) – Timing Parameters Specified by Software – Automatic Refresh Operation, Refresh Rate is Programmable – Automatic Update of DS, TCR and PASR Parameters • Energy-saving Capabilities – Self-refresh, Power-down and Deep Power Modes Supported • Power-up Initialization by Software • CAS Latency of 2, 3 Supported • Reset function supported (DDR2) • Auto Precharge Command Not Used • On Die Termination not supported • OCD mode not supported 7.3.2 External Bus Interface • Integrates Three External Memory Controllers: – Static Memory Controller – DDR2/SDRAM Controller – SLC Nand Flash ECC Controller • Additional logic for NAND Flash and CompactFlashTM • Optional Full 32-bit External Data Bus • Up to 26-bit Address Bus (up to 64MBytes linear per chip select) • Up to 6 chip selects, Configurable Assignment: – Static Memory Controller on NCS0 – DDR2/SDRAM Controller (SDCS) or Static Memory Controller on NCS1 – Static Memory Controller on NCS2 – Static Memory Controller on NCS3, Optional NAND Flash support – Static Memory Controller on NCS4 - NCS5, Optional CompactFlashM support 7.3.2.1 Static Memory Controller • 8-, 16- or 32-bit Data Bus • Multiple Access Modes supported – Byte Write or Byte Select Lines – Asynchronous read in Page Mode supported (4- up to 32-byte page size) • Multiple device adaptability – Control signals programmable setup, pulse and hold time for each Memory Bank • Multiple Wait State Management – Programmable Wait State Generation 27 6437DS–ATARM–23-Apr-13 – External Wait Request – Programmable Data Float Time • Slow Clock mode supported 7.3.2.2 DDR2/SDR Controller • Supports DDR2/LPDDR2, SDR-SDRAM and LPSDR • Numerous Configurations Supported – 2K, 4K, 8K, 16K Row Address Memory Parts – SDRAM with Four Internal Banks – SDR-SDRAM with 16- or 32- bit Data Path – DDR2/LPDDR with 16- bit Data Path – One Chip Select for SDRAM Device (256 Mbyte Address Space) • Programming Facilities – Multibank Ping-pong Access (Up to 4 Banks Opened at Same Time = Reduces Average Latency of Transactions) – Timing Parameters Specified by Software – Automatic Refresh Operation, Refresh Rate is Programmable – Automatic Update of DS, TCR and PASR Parameters (LPSDR) • Energy-saving Capabilities – Self-refresh, Power-down and Deep Power Modes Supported • SDRAM Power-up Initialization by Software • CAS Latency of 2, 3 Supported • Auto Precharge Command Not Used • SDR-SDRAM with 16-bit Datapath and Eight Columns Not Supported – Clock Frequency Change in Precharge Power-down Mode Not Supported 7.3.2.3 NAND Flash Error Corrected Code Controller • Tracking the accesses to a NAND Flash device by triggering on the corresponding chip select • Single bit error correction and 2-bit Random detection. • Automatic Hamming Code Calculation while writing – ECC value available in a register • Automatic Hamming Code Calculation while reading – Error Report, including error flag, correctable error flag and word address being detected erroneous – Support 8- or 16-bit NAND Flash devices with 512-, 1024-, 2048- or 4096-bytes pages 8. System Controller The System Controller is a set of peripherals that allows handling of key elements of the system, such as power, resets, clocks, time, interrupts, watchdog, etc. 28 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 The System Controller User Interface also embeds the registers that configure the Matrix and a set of registers for the chip configuration. The chip configuration registers configure the EBI chip select assignment and voltage range for external memories. 8.1 System Controller Mapping The System Controller’s peripherals are all mapped within the highest 16 KBytes of address space, between addresses 0xFFFF E800 and 0xFFFF FFFF. However, all the registers of the System Controller are mapped on the top of the address space. All the registers of the System Controller can be addressed from a single pointer by using the standard ARM instruction set, as the Load/Store instruction have an indexing mode of ±4 KB. Figure 8-1 on page 30 shows the System Controller block diagram. Figure 7-1 on page 23 shows the mapping of the User Interfaces of the System Controller peripherals. 29 6437DS–ATARM–23-Apr-13 8.2 System Controller Block Diagram Figure 8-1. SAM9M11 System Controller Block Diagram System Controller VDDCORE Powered irq0-irq2 fiq periph_irq[2..24] nirq nfiq Advanced Interrupt Controller pit_irq rtt_irq wdt_irq dbgu_irq pmc_irq rstc_irq int ntrst por_ntrst MCK periph_nreset Debug Unit dbgu_irq dbgu_txd dbgu_rxd MCK debug periph_nreset proc_nreset PCK debug Periodic Interval Timer pit_irq Watchdog Timer wdt_irq tag_nreset SLCK debug idle proc_nreset ARM926EJ-S Boundary Scan TAP Controller MCK wdt_fault WDRPROC NRST periph_nreset Bus Matrix rstc_irq por_ntrst tag_nreset VDDCORE POR Reset Controller periph_nreset proc_nreset backup_nreset VDDBU VDDBU POR VDDBU Powered SLCK UPLLCK UHP48M SLCK backup_nreset Real-Time Clock SLCK backup_nreset Real-Time Timer rtc_irq rtc_alarm UHP12M rtt_irq periph_nreset rtt_alarm periph_irq[25] USB High Speed Host Port SLCK SHDN WKUP backup_nreset RC OSC SLOW CLOCK OSC XIN32 XOUT32 rtt0_alarm 4 General-purpose Backup Registers XIN periph_nreset USB High Speed Device Port periph_irq[24] SCKCR SLCK XOUT UPLLCK Shut-Down Controller int 12MHz MAIN OSC UPLL PLLA MAINCK UPLLCK Power Management Controller periph_clk[2..30] pck[0-1] UHP48M UHP12M PCK MCK DDR sysclk pmc_irq idle PLLACK periph_clk[6..30] periph_nreset periph_nreset periph_nreset periph_clk[2..6] dbgu_rxd PA0-PA31 PB0-PB31 PC0-PC31 PD0-PD31 PIO Controllers periph_irq[2..6] irq fiq dbgu_txd Embedded Peripherals periph_irq[6..30] in out enable PE0-PE31 30 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 8.3 Reset Controller The Reset Controller is based on two Power-on-Reset cells, one on VDDBU and one on VDDCORE. The Reset Controller is capable to return to the software the source of the last reset, either a general reset (VDDBU rising), a wake-up reset (VDDCORE rising), a software reset, a user reset or a watchdog reset. The Reset Controller controls the internal resets of the system and the NRST pin output. It is capable to shape a reset signal for the external devices, simplifying to a minimum connection of a push-button on the NRST pin to implement a manual reset. The configuration of the Reset Controller is saved as supplied on VDDBU. 8.4 Shut Down Controller The Shut Down Controller is supplied on VDDBU and allows a software-controllable shut down of the system through the pin SHDN. An input change of the WKUP pin or an alarm releases the SHDN pin, and thus wakes up the system power supply. 8.5 Clock Generator The Clock Generator is made up of: • One Low Power 32768 Hz Slow Clock Oscillator with bypass mode • One Low-Power RC oscillator • One 12 MHz Main Oscillator, which can be bypassed • One 400 to 800 MHz programmable PLLA, capable to provide the clock MCK to the processor and to the peripherals. This PLL has an input divider to offer a wider range of output frequencies from the 12 MHz input, the only limitation being the lowest input frequency shall be higher or equal to 2 MHz. The USB Device and Host HS Clocks are provided by a the dedicated UTMI PLL (UPLL) embedded in the UTMI macro. 31 6437DS–ATARM–23-Apr-13 Figure 8-2. Clock Generator Block Diagram Clock Generator RCEN On Chip RC OSC XIN32 XOUT32 Slow Clock SLCK Slow Clock Oscillator OSCSEL OSC32EN OSC32BYP XIN 12M Main Oscillator Main Clock MAINCK XOUT UPLL UPLLCK PLLA Clock PLLACK PLLA and Divider Status Control Power Management Controller 8.6 Slow Clock Selection The SAM9M11 slow clock can be generated either by an external 32768Hz crystal or the onchip RC oscillator. The 32768 Hz crystal oscillator can be bypassed, by setting the bit OSC32BYP, to accept an external slow clock on XIN32. The internal RC oscillator and the 32768 Hz oscillator can be enabled by setting to 1 respectively RCEN bit and OSC32EN bit in the system controller user interface. OSCSEL command selects the slow clock source. RCEN, OSC32EN,OSCSEL and OSC32BYP bits are located in the slow clock control register (SCKCR) located at address 0xFFFFFD50 in the backup part of the system controller and so are preserved while VDDBU is present. 32 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Figure 8-3. Slow Clock Clock Generator RCEN On Chip RC OSC Slow Clock SLCK XIN32 Slow Clock Oscillator XOUT32 OSCSEL OSC32EN OSC32BYP After a VDDBU power on reset, the default configuration is RCEN = 1, OSC32EN = 0 and OSCSEL = 0 allowing the system to start on the internal RC oscillator. The programmer controls by software the slow clock switching and so must take precautions during the switching phase. 8.6.1 Switch from Internal RC Oscillator to the 32768 Hz Crystal To switch from internal RC oscillator to the 32768 Hz crystal, the programmer must execute the following sequence: • Switch the master clock to a source different from slow clock (PLLA or PLLB or Main Oscillator) through the Power Manage23-Apr-13ment Controller. • Enable the 32768 Hz oscillator by setting the bit OSCEN to 1. • Wait 32768 Hz startup time for clock stabilization (software loop). • Switch from internal RC to 32768 Hz by setting the bit OSCSEL to 1. • Wait 5 slow clock cycles for internal resynchronization. • Disable the RC oscillator by setting the bit RCEN to 0. 8.6.2 Bypass the 32768 Hz Oscillator The following step must be added to bypass the 32768 Hz Oscillator. • An external clock must be connected on XIN32. • Enable the bypass path OSC32BYP bit set to 1. • Disable the 32768 Hz oscillator by setting the bit OSC32EN to 0. 8.6.3 Switch from 32768 Hz Crystal to the Internal RC Oscillator The same procedure must be followed to switch from 32768 Hz crystal to the internal RC oscillator. • Switch the master clock to a source different from slow clock (PLLA or PLLB or Main Oscillator). • Enable the internal RC oscillator by setting the bit RCEN to 1. • Wait internal RC Startup Time for clock stabilization (software loop). 33 6437DS–ATARM–23-Apr-13 • Switch from 32768 Hz oscillator to internal RC oscillator by setting the bit OSCSEL to 0. • Wait 5 slow clock cycles for internal resynchronization. • Disable the 32768Hz oscillator by setting the bit OSC32EN to 0. 8.7 Power Management Controller The Power Management Controller provides all the clock signals to the system. PMC input clocks: • UPLLCK: From UTMI PLL • PLLACK From PLLA • SLCK: slow clock from OSC32K or internal RC OSC • MAINCK: from 12 MHz external oscillator PMC output clocks • Processor Clock PCK • Master Clock MCK, in particular to the Matrix and the memory interfaces. The divider can be 1,2,3 or 4 • DDR system clock equal to 2xMCK Note: DDR system clock is not available when Master Clock (MCK) equals Processor Clock (PCK). • USB Host EHCI High speed clock (UPLLCK) • USB OHCI clocks (UHP48M and UHP12M) • Independent peripheral clocks, typically at the frequency of MCK • Two programmable clock outputs: PCK0 and PCK1 This allows the software control of five flexible operating modes: • Normal Mode, processor and peripherals running at a programmable frequency • Idle Mode, processor stopped waiting for an interrupt • Slow Clock Mode, processor and peripherals running at low frequency • Standby Mode, mix of Idle and Backup Mode, peripheral running at low frequency, processor stopped waiting for an interrupt • Backup Mode, Main Power Supplies off, VDDBU powered by a battery 34 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 Figure 8-4. SAM9M11 Power Management Controller Block Diagram PLLACK USBS UHP48M USBDIV+1 USB OHCI UHP12M /4 USB EHCI /1,/2 PCK Processor Clock Controller UPLLCK int Divider MAINCK SLCK Prescaler /1,/2,/4,.../64 X /1 /1.5 /2 SysClk DDR /1 /2 MCK /3 /4 Peripherals Clock Controller ON/OFF Master Clock Controller SLCK MAINCK periph_clk[..] ON/OFF Prescaler /1,/2,/4,...,/64 pck[..] UPLLCK Programmable Clock Controller 8.7.1 8.7.1.1 Main Application Modes The Power Management Controller provides 3 main application modes. Normal Mode • PLLA and UPLL are running respectively at 400 MHz and 480 MHz • USB Device High Speed and Host EHCI High Speed operations are allowed • Full Speed OHCI input clock is UPLLCK, USBDIV is 9 (division by 10) • System Input clock is PLLACK, PCK is 400 MHz • MDIV is ‘11’, MCK is 133 MHz • DDR2 can be used at up to 133 MHz 8.7.1.2 USB HS and LP-DDR Mode • Only UPLL is running at 480 MHz, PLLA power consumption is saved • USB Device High Speed and Host EHCI High Speed operations are allowed • Full Speed OHCI input clock is UPLLCK, USBDIV is 9 (division by 10) • System Input clock is UPLLCK, Prescaler is 2, PCK is 240 MHz • MDIV is ‘01’, MCK is 120 MHz • Only LP-DDR can be used at up to 120 MHz 35 6437DS–ATARM–23-Apr-13 8.7.1.3 No UDP HS, UHP FS and DDR2 Mode • Only PLLA is running at 384 MHz, UPLL power consumption is saved • USB Device High Speed and Host EHCI High Speed operations are NOT allowed • Full Speed OHCI input clock is PLLACK, USBDIV is 7 (division by 8) • System Input clock is PLLACK, PCK is 384 MHz • MDIV is ‘11’, MCK is 128 MHz • DDR2 can be used at up to 128 MHz 8.8 Periodic Interval Timer • Includes a 20-bit Periodic Counter, with less than 1µs accuracy • Includes a 12-bit Interval Overlay Counter • Real Time OS or Linux/WinCE compliant tick generator 8.9 Watchdog Timer • 16-bit key-protected only-once-Programmable Counter • Windowed, prevents the processor to be in a dead-lock on the watchdog access 8.10 Real-Time Timer • Real-Time Timer, allowing backup of time with different accuracies – 32-bit Free-running back-up Counter – Integrates a 16-bit programmable prescaler running on slow clock – Alarm Register capable to generate a wake-up of the system through the Shut Down Controller 8.11 Real Time Clock • Low power consumption • Full asynchronous design • Two hundred year calendar • Programmable Periodic Interrupt • Alarm and update parallel load • Control of alarm and update Time/Calendar Data In 8.12 General-Purpose Backup Registers • Four 32-bit backup general-purpose registers 8.13 Advanced Interrupt Controller • Controls the interrupt lines (nIRQ and nFIQ) of the ARM Processor • Thirty-two individually maskable and vectored interrupt sources – Source 0 is reserved for the Fast Interrupt Input (FIQ) – Source 1 is reserved for system peripherals (PIT, RTT, PMC, DBGU, etc.) – Programmable Edge-triggered or Level-sensitive Internal Sources – Programmable Positive/Negative Edge-triggered or High/Low Level-sensitive 36 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 • One External Sources plus the Fast Interrupt signal • 8-level Priority Controller – Drives the Normal Interrupt of the processor – Handles priority of the interrupt sources 1 to 31 – Higher priority interrupts can be served during service of lower priority interrupt • Vectoring – Optimizes Interrupt Service Routine Branch and Execution – One 32-bit Vector Register per interrupt source – Interrupt Vector Register reads the corresponding current Interrupt Vector • Protect Mode – Easy debugging by preventing automatic operations when protect modes are enabled • Fast Forcing – Permits redirecting any normal interrupt source on the Fast Interrupt of the processor 8.14 Debug Unit • Composed of two functions – Two-pin UART – Debug Communication Channel (DCC) support • Two-pin UART – Implemented features are 100% compatible with the standard Atmel USART – Independent receiver and transmitter with a common programmable Baud Rate Generator – Even, Odd, Mark or Space Parity Generation – Parity, Framing and Overrun Error Detection – Automatic Echo, Local Loopback and Remote Loopback Channel Modes – Support for two PDC channels with connection to receiver and transmitter • Debug Communication Channel Support – Offers visibility of and interrupt trigger from COMMRX and COMMTX signals from the ARM Processor’s ICE Interface 8.15 Chip Identification The SAM9M11 Chip ID is defined in the Debug Unit Chip ID Register and Debug Unit Chip ID Extension Register. • Chip ID: 0x819B05A1 • Ext ID: 0x00000001 • JTAG ID: 05B2_703F • ARM926 TAP ID: 0x0792603F 37 6437DS–ATARM–23-Apr-13 8.16 PIO Controllers • 5 PIO Controllers, PIOA, PIOB, PIOC, PIOD and PIOE, controlling a maximum of 160 I/O Lines • Each PIO Controller controls up to 32 programmable I/O Lines – PIOA has 32 I/O Lines – PIOB has 32 I/O Lines – PIOC has 32 I/O Lines – PIOD has 32 I/O Lines – PIOE has 32 I/O Lines • Fully programmable through Set/Clear Registers • Multiplexing of two peripheral functions per I/O Line • For each I/O Line (whether assigned to a peripheral or used as general purpose I/O) – Input change interrupt – Glitch filter – Multi-drive option enables driving in open drain – Programmable pull up on each I/O line – Pin data status register, supplies visibility of the level on the pin at any time • Synchronous output, provides Set and Clear of several I/O lines in a single write 38 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 9. Peripherals 9.1 Peripheral Mapping As shown in Figure 7-1, the Peripherals are mapped in the upper 256 Mbytes of the address space between the addresses 0xFFF7 8000 and 0xFFFC FFFF. Each User Peripheral is allocated 16K bytes of address space. 9.2 Peripheral Identifiers Table 9-1 defines the Peripheral Identifiers of the SAM9M11. A peripheral identifier is required for the control of the peripheral interrupt with the Advanced Interrupt Controller and for the control of the peripheral clock with the Power Management Controller. Table 9-1. SAM9M11 Peripheral Identifiers Peripheral ID Peripheral Mnemonic Peripheral Name 0 AIC Advanced Interrupt Controller 1 SYS System Controller Interrupt 2 PIOA Parallel I/O Controller A 3 PIOB Parallel I/O Controller B 4 PIOC Parallel I/O Controller C 5 PIOD, PIOE External Interrupt FIQ Parallel I/O Controller D, Parallel I/O Controller E 6 TRNG 7 USART0 True Random Number Generator USART 0 8 USART1 USART 1 9 USART2 USART 2 10 USART3 USART 3 11 MCI0 High Speed Multimedia Card Interface 0 12 TWI0 Two-Wire Interface 0 13 TWI1 Two-Wire Interface 1 14 SPI0 Serial Peripheral Interface 15 SPI1 Serial Peripheral Interface 16 SSC0 Synchronous Serial Controller 0 17 SSC1 Synchronous Serial Controller 1 18 TC0 .. TC5 Timer Counter 0 .. Timer Counter 5 19 PWM Pulse Width Modulation Controller 20 TSADCC 21 DMAC DMA Controller USB Host High Speed Touch Screen ADC Controller 22 UHPHS 23 LCDC LCD Controller 24 AC97C AC97 Controller 25 EMAC Ethernet MAC 26 ISI Image Sensor Interface 27 UDPHS USB Device High Speed 28 AES, TDES, SHA Advanced Encryption Standard, Triple Data Encryption Standard, Secure Hash Algorithm 39 6437DS–ATARM–23-Apr-13 Table 9-1. SAM9M11 Peripheral Identifiers (Continued) Peripheral ID 9.3 9.3.1 Peripheral Mnemonic Peripheral Name 29 MCI1 High Speed Multimedia Card Interface 1 30 VDEC Video Decoder 31 AIC Advanced Interrupt Controller External Interrupt IRQ Peripheral Interrupts and Clock Control System Interrupt The System Interrupt in Source 1 is the wired-OR of the interrupt signals coming from: • the DDR2/LPDDR Controller • the Debug Unit • the Periodic Interval Timer • the Real-Time Timer • the Real-Time Clock • the Watchdog Timer • the Reset Controller • the Power Management Controller The clock of these peripherals cannot be deactivated and Peripheral ID 1 can only be used within the Advanced Interrupt Controller. 9.3.2 9.4 External Interrupts All external interrupt signals, i.e., the Fast Interrupt signal FIQ or the Interrupt signal IRQ, use a dedicated Peripheral ID. However, there is no clock control associated with these peripheral IDs. Peripheral Signals Multiplexing on I/O Lines The SAM9M11 features 5 PIO controllers, PIOA, PIOB, PIOC, PIOD and PIOE, which multiplexes the I/O lines of the peripheral set. Each PIO Controller controls up to 32 lines. Each line can be assigned to one of two peripheral functions, A or B. The multiplexing tables in the following paragraphs define how the I/O lines of the peripherals A and B are multiplexed on the PIO Controllers. The two columns “Function” and “Comments” have been inserted in this table for the user’s own comments; they may be used to track how pins are defined in an application. Note that some peripheral function which are output only, might be duplicated within the both tables. The column “Reset State” indicates whether the PIO Line resets in I/O mode or in peripheral mode. If I/O is mentioned, the PIO Line resets in input with the pull-up enabled, so that the device is maintained in a static state as soon as the reset is released. As a result, the bit corresponding to the PIO Line in the register PIO_PSR (Peripheral Status Register) resets low. If a signal name is mentioned in the “Reset State” column, the PIO Line is assigned to this function and the corresponding bit in PIO_PSR resets high. This is the case of pins controlling memories, in particular the address lines, which require the pin to be driven as soon as the reset is released. Note that the pull-up resistor is also enabled in this case. To amend EMC, programmable delay has been inserted on PIO lines able to run at high speed. 40 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 9.4.1 Table 9-2. PIO Controller A Multiplexing Multiplexing on PIO Controller A (PIOA) I/O Line Peripheral A Peripheral B Reset State Power Supply PA0 MCI0_CK TCLK3 I/O VDDIOP0 PA1 MCI0_CDA TIOA3 I/O VDDIOP0 PA2 MCI0_DA0 TIOB3 I/O VDDIOP0 PA3 MCI0_DA1 TCKL4 I/O VDDIOP0 PA4 MCI0_DA2 TIOA4 I/O VDDIOP0 PA5 MCI0_DA3 TIOB4 I/O VDDIOP0 PA6 MCI0_DA4 ETX2 I/O VDDIOP0 PA7 MCI0_DA5 ETX3 I/O VDDIOP0 PA8 MCI0_DA6 ERX2 I/O VDDIOP0 PA9 MCI0_DA7 ERX3 I/O VDDIOP0 PA10 ETX0 I/O VDDIOP0 PA11 ETX1 I/O VDDIOP0 PA12 ERX0 I/O VDDIOP0 PA13 ERX1 I/O VDDIOP0 PA14 ETXEN I/O VDDIOP0 PA15 ERXDV I/O VDDIOP0 PA16 ERXER I/O VDDIOP0 PA17 ETXCK I/O VDDIOP0 PA18 EMDC I/O VDDIOP0 PA19 EMDIO I/O VDDIOP0 PA20 TWD0 I/O VDDIOP0 PA21 TWCK0 I/O VDDIOP0 PA22 MCI1_CDA SCK3 I/O VDDIOP0 PA23 MCI1_DA0 RTS3 I/O VDDIOP0 PA24 MCI1_DA1 CTS3 I/O VDDIOP0 PA25 MCI1_DA2 PWM3 I/O VDDIOP0 PA26 MCI1_DA3 TIOB2 I/O VDDIOP0 PA27 MCI1_DA4 ETXER I/O VDDIOP0 PA28 MCI1_DA5 ERXCK I/O VDDIOP0 PA29 MCI1_DA6 ECRS I/O VDDIOP0 PA30 MCI1_DA7 ECOL I/O VDDIOP0 PA31 MCI1_CK PCK0 I/O VDDIOP0 Function Comments 41 6437DS–ATARM–23-Apr-13 9.4.2 PIO Controller B Multiplexing Table 9-3. Multiplexing on PIO Controller B (PIOB) Reset State Power Supply SPI0_MISO I/O VDDIOP0 PB1 SPI0_MOSI I/O VDDIOP0 PB2 SPI0_SPCK I/O VDDIOP0 PB3 SPI0_NPCS0 I/O VDDIOP0 PB4 TXD1 I/O VDDIOP0 PB5 RXD1 I/O VDDIOP0 PB6 TXD2 I/O VDDIOP0 PB7 RXD2 I/O VDDIOP0 PB8 TXD3 ISI_D8 I/O VDDIOP2 PB9 RXD3 ISI_D9 I/O VDDIOP2 PB10 TWD1 ISI_D10 I/O VDDIOP2 PB11 TWCK1 ISI_D11 I/O VDDIOP2 PB12 DRXD I/O VDDIOP0 PB13 DTXD I/O VDDIOP0 PB14 SPI1_MISO I/O VDDIOP0 PB15 SPI1_MOSI CTS0 I/O VDDIOP0 PB16 SPI1_SPCK SCK0 I/O VDDIOP0 PB17 SPI1_NPCS0 RTS0 I/O VDDIOP0 PB18 RXD0 SPI0_NPCS1 I/O VDDIOP0 PB19 TXD0 SPI0_NPCS2 I/O VDDIOP0 PB20 ISI_D0 I/O VDDIOP2 PB21 ISI_D1 I/O VDDIOP2 PB22 ISI_D2 I/O VDDIOP2 PB23 ISI_D3 I/O VDDIOP2 PB24 ISI_D4 I/O VDDIOP2 PB25 ISI_D5 I/O VDDIOP2 PB26 ISI_D6 I/O VDDIOP2 PB27 ISI_D7 I/O VDDIOP2 PB28 ISI_PCK I/O VDDIOP2 PB29 ISI_VSYNC I/O VDDIOP2 PB30 ISI_HSYNC I/O VDDIOP2 PB31 ISI_MCK I/O VDDIOP2 I/O Line Peripheral A PB0 42 Peripheral B PCK1 Function Comments SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 9.4.3 Table 9-4. PIO Controller C Multiplexing Multiplexing on PIO Controller C (PIOC) Reset State Power Supply DQM2 DQM2 VDDIOM1 PC1 DQM3 DQM3 VDDIOM1 PC2 A19 A19 VDDIOM1 PC3 A20 A20 VDDIOM1 PC4 A21/NANDALE A21 VDDIOM1 PC5 A22/NANDCLE A22 VDDIOM1 PC6 A23 A23 VDDIOM1 PC7 A24 A24 VDDIOM1 PC8 CFCE1 I/O VDDIOM1 PC9 CFCE2 RTS2 I/O VDDIOM1 PC10 NCS4/CFCS0 TCLK2 I/O VDDIOM1 PC11 NCS5/CFCS1 CTS2 I/O VDDIOM1 PC12 A25/CFRNW A25 VDDIOM1 PC13 NCS2 I/O VDDIOM1 PC14 NCS3/NANDCS I/O VDDIOM1 PC15 NWAIT I/O VDDIOM1 PC16 D16 I/O VDDIOM1 PC17 D17 I/O VDDIOM1 PC18 D18 I/O VDDIOM1 PC19 D19 I/O VDDIOM1 PC20 D20 I/O VDDIOM1 PC21 D21 I/O VDDIOM1 PC22 D22 I/O VDDIOM1 PC23 D23 I/O VDDIOM1 PC24 D24 I/O VDDIOM1 PC25 D25 I/O VDDIOM1 PC26 D26 I/O VDDIOM1 PC27 D27 I/O VDDIOM1 PC28 D28 I/O VDDIOM1 PC29 D29 I/O VDDIOM1 PC30 D30 I/O VDDIOM1 PC31 D31 I/O VDDIOM1 I/O Line Peripheral A PC0 Peripheral B Function Comments 43 6437DS–ATARM–23-Apr-13 9.4.4 PIO Controller D Multiplexing Table 9-5. Multiplexing on PIO Controller D (PIOD) I/O Line Peripheral A Peripheral B Reset State Power Supply PD0 TK0 PWM3 I/O VDDIOP0 PD1 TF0 I/O VDDIOP0 PD2 TD0 I/O VDDIOP0 PD3 RD0 I/O VDDIOP0 PD4 RK0 I/O VDDIOP0 PD5 RF0 I/O VDDIOP0 PD6 AC97RX I/O VDDIOP0 PD7 AC97TX TIOA5 I/O VDDIOP0 PD8 AC97FS TIOB5 I/O VDDIOP0 PD9 AC97CK TCLK5 I/O VDDIOP0 PD10 TD1 I/O VDDIOP0 PD11 RD1 I/O VDDIOP0 PD12 TK1 I/O VDDIOP0 PD13 RK1 I/O VDDIOP0 PD14 TF1 I/O VDDIOP0 PD15 RF1 I/O VDDIOP0 PD16 RTS1 I/O VDDIOP0 PD17 CTS1 I/O VDDIOP0 PD18 SPI1_NPCS2 IRQ I/O VDDIOP0 PD19 SPI1_NPCS3 FIQ I/O VDDIOP0 PD20 TIOA0 I/O VDDANA TSAD0 PD21 TIOA1 I/O VDDANA TSAD1 PD22 TIOA2 I/O VDDANA TSAD2 PD23 TCLK0 I/O VDDANA TSAD3 PD24 SPI0_NPCS1 PWM0 I/O VDDANA GPAD4 PD25 SPI0_NPCS2 PWM1 I/O VDDANA GPAD5 PD26 PCK0 PWM2 I/O VDDANA GPAD6 PD27 PCK1 SPI0_NPCS3 I/O VDDANA GPAD7 PD28 TSADTRG SPI1_NPCS1 I/O VDDIOP0 PD29 TCLK1 SCK1 I/O VDDIOP0 PD30 TIOB0 SCK2 I/O VDDIOP0 PD31 TIOB1 PWM1 I/O VDDIOP0 44 PCK0 Function Comments SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 9.4.5 Table 9-6. PIO Controller E Multiplexing Multiplexing on PIO Controller E (PIOE) I/O Line Peripheral A Peripheral B Reset State Power Supply PE0 LCDPWR PCK0 I/O VDDIOP1 PE1 LCDMOD I/O VDDIOP1 PE2 LCDCC I/O VDDIOP1 PE3 LCDVSYNC I/O VDDIOP1 PE4 LCDHSYNC I/O VDDIOP1 PE5 LCDDOTCK I/O VDDIOP1 PE6 LCDDEN I/O VDDIOP1 PE7 LCDD0 LCDD2 I/O VDDIOP1 PE8 LCDD1 LCDD3 I/O VDDIOP1 PE9 LCDD2 LCDD4 I/O VDDIOP1 PE10 LCDD3 LCDD5 I/O VDDIOP1 PE11 LCDD4 LCDD6 I/O VDDIOP1 PE12 LCDD5 LCDD7 I/O VDDIOP1 PE13 LCDD6 LCDD10 I/O VDDIOP1 PE14 LCDD7 LCDD11 I/O VDDIOP1 PE15 LCDD8 LCDD12 I/O VDDIOP1 PE16 LCDD9 LCDD13 I/O VDDIOP1 PE17 LCDD10 LCDD14 I/O VDDIOP1 PE18 LCDD11 LCDD15 I/O VDDIOP1 PE19 LCDD12 LCDD18 I/O VDDIOP1 PE20 LCDD13 LCDD19 I/O VDDIOP1 PE21 LCDD14 LCDD20 I/O VDDIOP1 PE22 LCDD15 LCDD21 I/O VDDIOP1 PE23 LCDD16 LCDD22 I/O VDDIOP1 PE24 LCDD17 LCDD23 I/O VDDIOP1 PE25 LCDD18 I/O VDDIOP1 PE26 LCDD19 I/O VDDIOP1 PE27 LCDD20 I/O VDDIOP1 PE28 LCDD21 I/O VDDIOP1 PE29 LCDD22 I/O VDDIOP1 PE30 LCDD23 I/O VDDIOP1 PE31 PWM2 I/O VDDIOP1 PCK1 Function Comments 45 6437DS–ATARM–23-Apr-13 10. Embedded Peripherals 10.1 Serial Peripheral Interface (SPI) • Supports communication with serial external devices – Four chip selects with external decoder support allow communication with up to 15 peripherals – Serial memories, such as DataFlash and 3-wire EEPROMs – Serial peripherals, such as ADCs, DACs, LCD Controllers, CAN Controllers and Sensors – External co-processors • Master or slave serial peripheral bus interface – 8- to 16-bit programmable data length per chip select – Programmable phase and polarity per chip select – Programmable transfer delays between consecutive transfers and between clock and data per chip select – Programmable delay between consecutive transfers – Selectable mode fault detection • Very fast transfers supported – Transfers with baud rates up to MCK – The chip select line may be left active to speed up transfers on the same device 10.2 Two Wire Interface (TWI) • Compatibility with standard two-wire serial memory • One, two or three bytes for slave address • Sequential read/write operations • Supports either master or slave modes • Compatible with Standard Two-wire Serial Memories • Master, Multi-master and Slave Mode Operation • Bit Rate: Up to 400 Kbits • General Call Supported in Slave mode 10.3 Universal Synchronous Asynchronous Receiver Transmitter (USART) • Programmable Baud Rate Generator • 5- to 9-bit full-duplex synchronous or asynchronous serial communications – 1, 1.5 or 2 stop bits in Asynchronous Mode or 1 or 2 stop bits in Synchronous Mode – Parity generation and error detection – Framing error detection, overrun error detection – MSB- or LSB-first – Optional break generation and detection – By 8 or by-16 over-sampling receiver frequency – Hardware handshaking RTS-CTS 46 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 – Receiver time-out and transmitter timeguard – Optional Multi-drop Mode with address generation and detection – Optional Manchester Encoding • RS485 with driver control signal • ISO7816, T = 0 or T = 1 Protocols for interfacing with smart cards – NACK handling, error counter with repetition and iteration limit • IrDA modulation and demodulation – Communication at up to 115.2 Kbps • SPI Mode – Master or Slave – Serial Clock Programmable Phase and Polarity – SPI Serial Clock (SCK) Frequency up to Internal Clock Frequency MCK/4 • LIN Mode – Compliant with LIN 1.3 and LIN 2.0 specifications – Master or Slave – Processing of frames with up to 256 data bytes – Response Data length can be configurable or defined automatically by the Identifier – Self synchronization in Slave node configuration – Automatic processing and verification of the “Synch Break” and the “Synch Field” – The “Synch Break” is detected even if it is partially superimposed with a data byte – Automatic Identifier parity calculation/sending and verification – Parity sending and verification can be disabled – Automatic Checksum calculation/sending and verification – Checksum sending and verification can be disabled – Support both “Classic” and “Enhanced” checksum types – Full LIN error checking and reporting – Frame Slot Mode: the Master allocates slots to the scheduled frames automatically. – Generation of the Wakeup signal • Test Modes – Remote Loopback, Local Loopback, Automatic Echo 10.4 Serial Synchronous Controller (SSC) • Provides serial synchronous communication links used in audio and telecom applications (with CODECs in Master or Slave Modes, I2S, TDM Buses, Magnetic Card Reader,...) • Contains an independent receiver and transmitter and a common clock divider • Offers a configurable frame sync and data length • Receiver and transmitter can be programmed to start automatically or on detection of different event on the frame sync signal • Receiver and transmitter include a data signal, a clock signal and a frame synchronization signal 47 6437DS–ATARM–23-Apr-13 10.5 AC97 Controller • Compatible with AC97 Component Specification V2.2 • Capable to Interface with a Single Analog Front end • Three independent RX Channels and three independent TX Channels – One RX and one TX channel dedicated to the AC97 Analog Front end control – One RX and one TX channel for data transfers, associated with a PDC – One RX and one TX channel for data transfers with no PDC • Time Slot Assigner allowing to assign up to 12 time slots to a channel • Channels support mono or stereo up to 20 bit sample length – Variable sampling rate AC97 Codec Interface (48KHz and below) 10.6 Timer Counter (TC) • Three 16-bit Timer Counter Channels • Wide range of functions including: – Frequency Measurement – Event Counting – Interval Measurement – Pulse Generation – Delay Timing – Pulse Width Modulation – Up/down Capabilities • Each channel is user-configurable and contains: – Three external clock inputs – Five internal clock inputs – Two multi-purpose input/output signals • Two global registers that act on all three TC Channels 10.7 Pulse Width Modulation Controller (PWM) • Four channels, one 16-bit counter per channel • Common clock generator, providing Thirteen Different Clocks – A Modulo n counter providing eleven clocks – Two independent Linear Dividers working on modulo n counter outputs • Independent channel programming – Independent Enable Disable Commands – Independent Clock Selection – Independent Period and Duty Cycle, with Double Buffering – Programmable selection of the output waveform polarity – Programmable center or left aligned output waveform 10.8 High Speed Multimedia Card Interface (MCI) • Compatibility with MultiMedia Card Specification Version 4.3 48 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 • Compatibility with SD Memory Card Specification Version 2.0 • Compatibility with SDIO Specification Version V2.0. • Compatibility with Memory Stick PRO • Compatibility with CE ATA 10.9 USB High Speed Host Port (UHPHS) • Compliant with Enhanced HCI Rev 1.0 Specification – Compliant with USB V2.0 High-speed and Full-speed Specification – Supports Both High-speed 480Mbps and Full-speed 12 Mbps USB devices • Compliant with Open HCI Rev 1.0 Specification – Compliant with USB V2.0 Full-speed and Low-speed Specification – Supports Both Low-speed 1.5 Mbps and Full-speed 12 Mbps USB devices • Root Hub Integrated with 2 Downstream USB Ports • Shared Embedded USB Transceivers 10.10 USB High Speed Device Port (UDPHS) • USB V2.0 high-speed compliant, 480 MBits per second • Embedded USB V2.0 UTMI+ high-speed transceiver shared with UHP HS. • Embedded 4-KByte dual-port RAM for endpoints • Embedded 6 channels DMA controller • Suspend/Resume logic • Up to 2 or 3 banks for isochronous and bulk endpoints • Seven endpoints: – Endpoint 0: 64 bytes, 1 bank mode – Endpoint 1 & 2: 1024 bytes, 2 banks mode, High Bandwidth, DMA – Endpoint 3 & 4: 1024 bytes, 3 banks mode, DMA – Endpoint 5 & 6: 1024 bytes, 3 banks mode, High Bandwidth, DMA 10.11 LCD Controller (LCDC) • Single and Dual scan color and monochrome passive STN LCD panels supported • Single scan active TFT LCD panels supported. • 4-bit single scan, 8-bit single or dual scan, 16-bit dual scan STN interfaces supported • Up to 24-bit single scan TFT interfaces supported • Up to 16 gray levels for mono STN and up to 4096 colors for color STN displays • 1, 2 bits per pixel (palletized), 4 bits per pixel (non-palletized) for mono STN • 1, 2, 4, 8 bits per pixel (palletized), 16 bits per pixel (non-palletized) for color STN • 1, 2, 4, 8 bits per pixel (palletized), 16, 24 bits per pixel (non-palletized) for TFT • Single clock domain architecture • Resolution supported up to 2048 x 2048 49 6437DS–ATARM–23-Apr-13 10.12 Touch Screen Analog-to-Digital Converter (TSADC) • 8-channel ADC • Support 4-wire resistive Touch Screen • 10-bit 384 Ksamples/sec. Successive Approximation Register ADC • -3/+3 LSB Integral Non Linearity, -2/+2 LSB Differential Non Linearity • Integrated 8-to-1 multiplexer, offering eight independent 3.3V analog inputs • External voltage reference for better accuracy on low voltage inputs • Individual enable and disable of each channel • Multiple trigger sources – Hardware or software trigger – External trigger pin • Sleep Mode and conversion sequencer – Automatic wakeup on trigger and back to sleep mode after conversions of all enabled channels 10.13 Ethernet 10/100 MAC (EMAC) • Compatibility with IEEE Standard 802.3 • 10 and 100 MBits per second data throughput capability • Full- and half-duplex operations • MII or RMII interface to the physical layer • Register Interface to address, data, status and control registers • DMA Interface, operating as a master on the Memory Controller • Interrupt generation to signal receive and transmit completion • 128-byte transmit and 128-byte receive FIFOs • Automatic pad and CRC generation on transmitted frames • Address checking logic to recognize four 48-bit addresses • Supports promiscuous mode where all valid frames are copied to memory • Supports physical layer management through MDIO interface • Supports Wake On Lan. The receiver supports Wake on LAN by detecting the following events on incoming receive frames: – Magic packet – ARP request to the device IP address – Specific address 1 filter match – Multicast hash filter match 10.14 Image Sensor Interface (ISI) • ITU-R BT. 601/656 8-bit mode external interface support • Support for ITU-R BT.656-4 SAV and EAV synchronization • Vertical and horizontal resolutions up to 2048 x 2048 • Preview Path up to 640*480 • Support for packed data formatting for YCbCr 4:2:2 formats 50 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 • Preview scaler to generate smaller size image 10.15 8-channel DMA (DMA) • Acting as two Matrix Masters • Embeds 8 unidirectional channels with programmable priority • Address Generation – Source/Destination address programming – Address increment, decrement or no change – DMA chaining support for multiple non-contiguous data blocks through use of linked lists – Scatter support for placing fields into a system memory area from a contiguous transfer. Writing a stream of data into non-contiguous fields in system memory – Gather support for extracting fields from a system memory area into a contiguous transfer – User enabled auto-reloading of source, destination and control registers from initially programmed values at the end of a block transfer – Auto-loading of source, destination and control registers from system memory at end of block transfer in block chaining mode – Unaligned system address to data transfer width supported in hardware • Channel Buffering – 16-word FIFO – Automatic packing/unpacking of data to fit FIFO width • Channel Control – Programmable multiple transaction size for each channel – Support for cleanly disabling a channel without data loss – Suspend DMA operation – Programmable DMA lock transfer support • Transfer Initiation – Support for Software handshaking interface. Memory mapped registers can be used to control the flow of a DMA transfer in place of a hardware handshaking interface • Interrupt – Programmable Interrupt generation on DMA Transfer completion Block Transfer completion, Single/Multiple transaction completion or Error condition 10.16 True Random Number Generator (TRNG) • Passed NIST Special Publication 800-22 Tests Suite • Passed Diehard Random Tests Suite • Provides a 32-bit Random Number Every 84 Clock Cycles • For 133 MHz Clock Frequency, Throughput Close to 50 Mbits/s 10.17 Advanced Encryption Standard (AES) • Compliant with FIPS Publication 197, Advanced Encryption Standard (AES) 51 6437DS–ATARM–23-Apr-13 • 256-bit Cryptographic Key • 16 Clock Cycles Encryption/Decryption Processing Time with a 256-bit Cryptographic Key • Support of the Five Standard Modes of Operation Specified in the NIST Special Publication 800- 38A, Recommendation for Block Cipher Modes of Operation - Methods and Techniques: – Electronic Code Book (ECB) – Cipher Block Chaining (CBC) – Cipher Feedback (CFB) – Output Feedback (OFB) – Counter (CTR) • 8-, 16-, 32-, 64- and 128-bit Data Sizes Possible in CFB Mode • Last Output Data Mode Allows Optimized Message Authentication Code (MAC) Generation • Hardware Counter Measures against Differential Power Analysis Attacks • Connected to the DMA Controller to optimize Data Transfers for all Operating Modes – One Channel for the Receiver, One Channel for the Transmitter – Next Buffer Support 10.18 Triple Data Encryption Standard (TDES) • Supports Single Data Encryption Standard (DES) and Triple Data Encryption Algorithm (TDEA or TDES) • Compliant with FIPS Publication 46-3, Data Encryption Standard (DES) • 64-bit Cryptographic Key for TDES • Two-key or Three-key Algorithms for TDES • 18-clock Cycles Encryption/Decryption Processing Time for DES • 50-clock Cycles Encryption/Decryption Processing Time for TDES • Support the Four Standard Modes of Operation specified in the FIPS Publication 81, DES Modes of Operation – Electronic Code Book (ECB) – Cipher Block Chaining (CBC) – Cipher Feedback (CFB) – Output Feedback (OFB) • 8-, 16-, 32-, 64- and 128-bit Data Sizes Possible in CFB Mode • Last Output Data Mode Allows Optimized Message (Data) Authentication Code (MAC) Generation • Connection to PDC Channel Capabilities Optimizes Data Transfers for all Operating Modes – One Channel for the Receiver, One Channel for the Transmitter – Next Buffer Support 10.19 Secure Hash Algorithm (SHA) • Supports Secure Hash Algorithm (SHA1 and SHA256) • Compliant with FIPS Publication 180-2 • Configurable Processing Period: 52 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 – 85 Clock Cycles to Maximize the Bandwidth for SHA1 or 386 Clock Cycles or Other Applications in PDC (Peripheral DMA) – 72 Clock Cycles to Maximize the Bandwidth for SHA256 or 265 Clock Cycles or Other Applications in PDC (Peripheral DMA) • Connection to PDC Channel Capabilities Optimizes Data Transfers – One Channel for the Transmitter – Next Buffer Support 10.20 Video Decoder (VDEC) • Little-endian and Big-endian support. Decoder supported standards: • MPEG-4 Simple and Advanced Profile, levels 0-5 • H.264 Baseline Profile, levels 1-3.1 • H.263 Profile 0, levels 10-70 • VC-1 – Simple Profile, Low and Medium Levels – Main Profile, Low, Medium and High Levels – Advanced Profile, Levels 0-3 • MPEG-2 Main Profile, Low, Medium and High Levels • JPEG Profile Baseline DCT (sequential) and JFIF 1.02 file form Post-processor features: • Image up-scaling • Image down-scaling • YCbCr to RGB conversion • Dithering • Deinterlacing • Programmable alpha channel • Alpha blending • De-blocking filter for MPEG-4 simple profile/H.263 • Image cropping / digital zoom • Picture in picture • Supported display size for picture in picture • Image rotation 53 6437DS–ATARM–23-Apr-13 11. Mechanical Characteristics 11.1 Package Drawings Figure 11-1. 324-ball TFBGA Package Drawing 54 SAM9M11 6437DS–ATARM–23-Apr-13 SAM9M11 12. SAM9M11 Ordering Information Table 12-1. AT91SAM9M11 Ordering Information Ordering Code Package Package Type Temperature Operating Range AT91SAM9M11B-CU TFBGA324 Green Industrial -40°C to 85°C 55 6437DS–ATARM–23-Apr-13 Revision History Change Request Ref. Doc. Rev Comments 6355DS In “Features” on page 1 added mention of DBGU. In Section 12. “SAM9M11 Ordering Information” updated Table 12-1, “AT91SAM9M11 Ordering Information,” on page 55 6355CS Product Line/Product naming convention changed - AT91SAM ARM-based MPU / SAM9M11 Section 5.1 “Power Supplies”, replaced ground pin names by GNDIOM, GNDCORE, GNDANA, GNDIOP, GNDBU, GNDOSC, GNDUTMI. Reorganized text describing GND association to power supply pins rfo 8551 rfo 7332 rfo Section 10.20 “Video Decoder (VDEC)” added. RFO ‘11-layer --> ‘12-layer’ in Section 6.2 “Bus Matrix”. 7172 6437BS 6437AS 56 First issue SAM9M11 6437DS–ATARM–23-Apr-13 Headquarters International Atmel Corporation 1600 Technology Drive San Jose, CA 95110 USA Tel: (+1) (408) 441-0311 Fax: (+1) (408) 487-2600 Atmel Asia Limited Unit 01-5 & 16, 19F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 16F, Shin-Osaki Kangyo Bldg. 1-6-4 Osaki, Shingawa-ku Tokyo 141-0032 JAPAN Tel: (+81)( 3) 6417-0300 Fax: (+81)( 3) 6417-0370 Technical Support AT91SAM Support Atmel technical support Sales Contacts www.atmel.com/contacts/ Product Contact Web Site www.atmel.com www.atmel.com/AT91SAM Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2013 Atmel Corporation. All rights reserved. Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, DataFlash®, SAM-BA® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. ARM® logo, Thumb® and others are the registered trademarks or trademarks of ARM Ltd. Windows® and others are registered trademarks or trademarks of Microsoft Corporation in the US and/or other countries. Other terms and product names may be the trademarks of others. 6437DS–ATARM–23-Apr-13