Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Antenna Driver Stage with Adjustable Antenna Peak Current for up to 1.5A
Frequency Tuning Range from 100 kHz to 150 kHz
Automatic Antenna Peak Current Regulation
Self-tuning Oscillator for Antenna Resonant Frequency Adaptation
Capable of Driving a High-Q Antenna
Integrated 5V Regulator for External Load up to 10 mA
Bi-directional Single Wire Interface for Microcontroller or ECU
LF Baud Rates up to 4 kbaud and Amplitude Shift Keying (ASK) Modulation
Low Power Standby Mode < 50 µA
Antenna Driver Diagnosis: Peak Current, Antenna Frequency and Battery Voltage
Monitoring
Power Supply Range 8V to 24V Direct Battery Input
Load Dump Protection
Operation at Temperature –40°C to +105°C
EMI and ESD According to Automotive Requirements
Highly Integrated, Fewer External Components Required
Overtemperature Protection
125 kHz
Transmitter IC
for TPM
ATA5276
Applications
•
•
•
•
Tire Pressure Measurement (TPM)
Wake-Up Systems
Auditing/Tracking Systems
Localization/Security Systems
Benefits
•
•
•
•
Self Tuning Capability to Antenna Resonance Frequency
Adjustable Antenna Peak Current Value
Highest Integration Level for Embedded Automotive Systems
Power Saving/Low Current Consumption for Wake-Up Systems
1. Description
The ATA5276 is an integrated 1.5A peak current BCDMOS antenna driver IC dedicated as a 125 kHz wake-up channel transmitter for TPM applications.
It includes the full functionality to generate a magnetic LF field in conjunction with an
antenna coil to transmit data and power to a receiver. The transmission can be controlled via a one wire I/O-interface by an external unit.
The smart power IC is delivered in a QFN20 power package with heat slug.
4909C–AUTO–01/07
2. General Description
The ATA5276 is a 125-kHz transmitter IC. It is dedicated to driving 125 kHz LC antenna tanks,
for the wake-up channel in Tire Pressure Measurement (TPM) applications or various power
saving Industrial wake-up applications..
It includes a control logic with VCO which generates the 125 kHz signal for the output driver
stage. A phase lock circuit regulates the driver output frequency on the antenna resonance frequency, achieving a maximum field strength on the antenna. The driver duty cycle is regulated
and stabilizes the antenna current for a wide supply voltage range.
The IC can be controlled by a microcontroller or ECU via the one wire bi-directional interface. It
is used for the data transmission and to indicate errors. For the data transmission ASK modulation is used. The antenna signal is modulated by the DIO interface line.
The IC has a build in diagnosis function and detects detuning and broken or short wire of the
antenna circuitry. If a failure is detected the IC indicates it by an error signal via the DIO line.
The integrated 5V regulator can be used externally for a load up to 10 mA.
Figure 2-1.
Block Diagram
20
DVCC3
19
BOOST
1
5V
REG
DVCC2
17
DIO
REF
16
VDIO
BIAS
KLine
ATA5276
2
DVCC1
State
Machine
Gate
Drive
Control
VCO
11
REXT
5
DRV1
6
DVSS3
2
7
DVSS2
8
DVSS1
13
TM3
12
RCR
XOR
4
DRV2
15
TM1
14
TM2
125-kHz Transmitter
Half Bridge
3
DRV3
18
VCC
9
SENSE
10
VSS
ATA5276
4909C–AUTO–01/07
ATA5276
3. Pin Configuration
Figure 3-1.
Pinning QFN20
20
19
DVCC3 BOOST
18
VCC
17
DIO
16
VDIO
1
15
TM1
DVCC2
2
DVCC1
14
TM2
ATA5276
3
DRV3
4
DRV2
12
RCR
5
DRV1
11
REXT
6
DVSS3
Table 3-1.
Pin
7
DVSS2
8
DVSS1
9
SENSE
10
VSS
Pin Description
(1)
Symbol
Function
1
DVCC2
Battery supply input
2
DVCC1
Battery supply input
3
DRV3
Antenna driver stage output
4
DRV2
Antenna driver stage output
5
DRV1
Antenna driver stage output
6
DVSS3
Power supply ground
7
DVSS2
Power supply ground
8
DVSS1
Power supply ground
9
SENSE
Current zero crossing sense input
10
VSS
11
REXT
External reference current input
12
RCR
External reference for antenna peak current
13
TM3
For test purposes only
14
TM2
For test purposes only
15
TM1
For test purposes only
16
VDIO
DIO line interface voltage selection
17
DIO
Analog and digital ground
One-wire serial interface line
18
VCC
19
BOOST
External bootstrap cap
20
DVCC3
Battery supply input
Note:
13
TM3
5V supply output (for external storage capacitor only)
1. Pin numbers valid for all revisions of the ATA5276
3
4909C–AUTO–01/07
4. Functional Description
4.1
Operation Modes
There are two different operation modes for the ATA5276:
• Standby mode
• Transmission mode
4.2
Standby Mode and Wake-up
After power-on-reset, the ATA5276 is in standby mode. For minimum power consumption, only
the internal 5V supply and the DIO line interface are active. The IC can be activated by the external control unit via the serial interface. The DIO line is called logic high if it is pulled up to the
VDIO voltage level. The DIO line is called logic low if it is pulled down to the VSS voltage level. A
low signal at the DIO line wakes-up the IC.
The circuit enters the standby mode if either of these three conditions are fulfilled:
1. After power-on-reset and the DIO is high (see Figure 4-1)
2. After a time out of TOUTL(1) during which DIO is permanently low (see Figure 4-3 on
page 5)
3. After a time out of TOUTH(2) during which DIO is permanently high and an acknowledge
time TACK/TERR(1) (see Figure 4-2)
Notes:
1. Time does not depend on the antenna resonance frequency.
2. Time depends on the antenna resonance frequency.
Figure 4-1.
STBY After POR
STBY
t
DIO
t
POR
t
Figure 4-2.
STBY After DIO = H
STBY
t
TOUT_H
TACK/TERR
DIO
t
4
ATA5276
4909C–AUTO–01/07
ATA5276
Figure 4-3.
STBY After DIO = L
TOUT_L
STBY
t
DIO
t
4.3
4.3.1
Transmission Mode
ASK Modulation
For the transmission of a wake-up signal or data to a receiver, the ATA5276 generates a
antenna resonance synchronized signal at the antenna driver output (DRV pin). A connected LC
antenna radiates a magnetic field. For the data transmission the field can be 100% amplitude
modulated by the DIO interface input. If a low level signal is applied at the DIO pin, the driver
generates a square wave signal DRV for the antenna. If a high level signal is applied at the DIO
pin the driver is stopped and switched to ground. In this way ASK modulated data can be transmitted (see Figure 4-4).
Figure 4-4.
Data Transmission
DIO
DRV
COIL
4.3.2
Anti-bouncing Filter in Transmission Mode
The DIO input signal is delayed for a anti-bouncing time.
The driver is switched on after a delay time of TDL (typically 64 µs) if the DIO is pulled to a low
level continuously. The driver is switched-off after a delay time of TDH if the DIO is pulled to high
level.
The TDH time depends on the antenna resonance frequency, suppressing short disturbance
pulses from the DIO line.
Figure 4-5.
Anti-bouncing
TD_L
TD_H
5
4909C–AUTO–01/07
4.3.3
Time Out and Time Out Reset
The IC has a time out supervisor for the interface line to avoid unintended continuous transmission in case of line errors. The time out timer runs if the DIO pin is pulled to a low level. If the DIO
pin is permanently low for more than the time TOUTL the driver is switched off and the IC enters
the standby mode. This avoids the discharging of the supply battery if the DIO line has a failure
like a body contact or another permanent low level failure. The time TOUTL depends on the
antenna resonance frequency.
Figure 4-6.
Time Out and Time Out Reset Protocol
Transmission
Delay
Standby
Time Out
Standby
TD_L TOUT_L
Timeout
Reset
TOR
Time Out
Reset Periode
TORP
Transmission
Delay
TD_H
DIO
DRV
For continuous transmission periods the internal time out timer must be reset within the time out
reset period TORP with a short high pulse of length TOR at DIO. Any transmission time periods
can be made by cyclical resetting of the time out timer (see Figure 4-6). The time TORP and TOR
depends on the antenna resonance frequency.
4.3.4
Transmission Acknowledge and Error Signal
If no failure is detected during a transmission sequence the IC acknowledges the transmission
by pulling the DIO line to low level for time TACK (typically 256 µs). The acknowledge signal is
generated at the end of a transmission sequence if the DIO line was high for the time TOUTH (typically 16 ms).
Their are two types of error detection (see section “Diagnosis and Protection” on page 8):
• Immediate switch-off of the driver stage
• The failure is indicated through the DIO line based on transmission acknowledge and Error
signal
At the end of transmission the IC indicates the failure by an error signal by pulling the DIO line to
a low level for time TERR (typically 128 µs) instead of TACK.
With the acknowledge and the error signal a connected microcontroller is able to recognize failures of the IC or the antenna module as well as DIO line failures like a broken wire or a short
circuit.
6
ATA5276
4909C–AUTO–01/07
ATA5276
Figure 4-7.
Transmission Acknowledge and Error Signal
Time Out
TOUT_H
Acknowledge
TACK
Failure Detection
Time Out
TOUT_H
Error Signal
TERR
TDFx
DIO
DRV
Failure
COIL
The various failure types are monitored during transmission in time TFDx (see section “Diagnosis and Protection” on page 8). The time TFDx depends on the antenna resonance frequency.
4.4
Internal Voltage Regulator and POR
The IC contains a 5-V regulator. It is used for the supply voltage VCC of the logic circuits and the
low voltage analog circuits. Additionally, the VCC can be used externally for loads up to 10 mA.
The stabilized voltage is available at pin VCC and must be buffered with an external capacitor.
4.4.1
Reset
After power on or after a voltage breakdown the power-on-reset circuit of the IC generates a
reset pulse which sets the logic circuit to a defined initial state. A RESET is generated if the VCC
is below the reset threshold voltage VPOR and after power on.
4.4.2
DIO Interface
The interface can be operated either as a 5-V microcontroller interface or as automotive K-line
interface with the car battery voltage. In which mode it operates must be selected with the VDIO
pin. If it is connected to 5V the DIO pin operates as microcontroller interface and if it is connected with the battery voltage it operates as automotive interface according to the K-line
specification.
4.5
Oscillator and Carrier Frequency Generation
A Voltage Controlled Oscillator (VCO) is used to clock the interface logic and the gate driver
logic. The antenna driver output signal DRV is derived from this clock. The VCO operates in two
modes: the self-oscillation mode with clock CLKSO and the resonance tracking mode with clock
CLKRT.
4.5.1
Self-oscillating Mode
If the antenna half-bridge is not activated the VCO is in self-oscillating mode. It runs at a center
frequency CLKSO of typically 125 kHz with an accuracy of ±8%. For that purpose, an external
reference resistor has to be applied to pin REXT. The resistor at pin REXT determines the VCO
frequency proportionally. The recommended value is 100 kΩ achieving 125 kHz oscillator
frequency.
7
4909C–AUTO–01/07
4.5.2
Resonance Tracking Mode
In case the antenna half-bridge is activated the VCO is tracked by the antenna current by means
of it zero crossing detection. The VCO runs at the antenna resonance frequency stationary. The
clock CLKRT deviates ±1.4% from the antenna resonance frequency, depending on the antenna
quality and resonance frequency (see section “Application Hints” on page 14). For that purpose,
an antenna current shunt resistor has to be applied to the SENSE pin. The shunt resistance is
used internally for the zero crossing detection of the antenna current only.
By this feature the antenna operates with the maximum voltage, current and field strength. It is
recommended specially for systems with high antenna Q-factors and low LC tolerances.
4.6
Coil Driver Output and Antenna Peak Current Control
The driver circuit consists on a DMOS half-bridge designed for 1.5A peak current with low
on-resistance RDSON. It is short-circuit and overtemperature protected (see section “Diagnosis
and Protection” on page 8). The half-bridge is switched on by a low level signal at DIO and generates a square wave voltage for the antenna RLC circuitry.
A very useful function of the driver stage is the build-in antenna current control loop. The IC
senses the current through the antenna internally and controls the peak value IAPEAK by controlling the duty cycle DCDRV of the driver output.
So the antenna can be designed for maximum antenna current with the typical or even the minimum supply voltage. For higher supply voltages the current is controlled by reducing the driver
duty cycle. The reference value for the antenna current IAPEAK can be adjusted externally with a
resistor RCR at the RCR pin.
50 kΩ
IA PEAK = 750 mA × --------------R CR
Note:
Applying the formula above, the right driver current for the antenna has to be adjusted for the
worst supply voltage case. The IC operates from 14% up to 86% duty cycle for that case and
reduces the duty cycle for higher voltages (for the definition of the duty cycle DCDRV, see “Application Hints” on page 14).
This feature allows the user to operate the IC in a wide field of operational voltage field and protects the driver stage and the antenna from antenna overcurrent.
The driver out square wave starts with a duty cycle of 50%. After three or four cycles the duty
cycle can reach its maximum. As far as the peak current will stay smaller than IApeak this duty
cycle maximum is really 100%. If during the ramp up of the antenna current the envelope of the
peak current will be greater than IApeak + 20% a pulse skipping function will suppress the next
driver output pulse to minimize the antenna current overshoot.
4.7
Diagnosis and Protection
The IC supervises several parameters of IC operation for transmission diagnosis and circuit
protection.
In any case of circuit protection mode or error detection the IC indicates this states according to
the transmission protocol via the DIO line (see section “Transmission Acknowledge and Error
Signal” on page 6).
8
ATA5276
4909C–AUTO–01/07
ATA5276
4.7.1
Circuit Protection Cases
The circuit protection is activated in normal mode, i.e., if the antenna circuit is driven to the oscillation with its own frequency. It is switched off in standby mode. Between the end of the
transmission and the acknowledge signal the low side driver is switched on. In case a protection
switch-off occurs the half-bridge is set in tri-state mode.
For all cases, there is a filter implemented to debounce half-bridge switch-off for a time of TDEB
(typically 20 µs). This debounce filter is activated in case the half-bridge is activated.
These are the following circuit protection cases:
1. Load dump protection: In case the voltage at DVCC exceeds a voltage VBATLD (typically 31V).
2. Overtemperature protection: In case the junction temperature exceeds a value of TSD
(typically 165°C).
4.7.2
Error Diagnosis
During the transmission the diagnosis function of the IC supervises the antenna current and frequency and the half-driver bridge supply voltage. If any error is detected at the end of the
transmission cycle the error indication is set (as in circuit protection case).
There are the following diagnosis cases:
1. Under-voltage detection: Monitors if DVCC is below VBATUV (typically 6.5V).
2. Antenna frequency error: Diagnosis if the oscillation frequency during transmission is
outside the typical tracking range 90 kHz to 160 kHz.
3. Antenna peak current error: Diagnosis if the peak current is greater than the adjusted
IAPEAK + 15% typically.
9
4909C–AUTO–01/07
5. Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Symbol
Min.
Max.
Unit
VSS
0
0
V
Power ground
DVSS1,2,3
–0.3
+0.3
V
Reverse protected battery voltage
DVCC1,2,3
–0.3
+44
V
Ground
Half-bridge driver output
Bootstrap
DRV1,2,3
–0.3
DVCC + 0.3
V
BOOST
–0.3
DVCC + 6(2)
V
VCC
–0.3
+7
V
REXT
–0.3
VCC + 0.3
V
5-V regulator output
Analog reference input
Digital test mode
RCR
–0.3
VCC + 0.3
V
TM1,2,3
–0.3
VCC + 0.3
V
VDIO
–0.3
DVCC + 0.3
V
DIO
–0.3
DVCC + 0.3
V
SENSE
–2
DVCC + 0.3
V
250
V/M
4 (on PCB)
kV
DIO interface supply
DIO interface
Zero crossing analog input
Electromagnetic Interference
EMI
Minimum ESD protection
(100 pF through 1.5 kΩ), at all pins
Power dissipation
Ptot
2(1)
W
Junction temperature
ϑj
150
°C
Storage temperature
ϑ STORE
–55
+125
°C
Ambient temperature range under bias
ϑ ambient
–40
+105
°C
260 +0/–5
°C
Soldering temperature (10s)
Notes:
ϑ SOLDERING
1. May be limited by external thermal resistance.
2. If the low side driver is switched on, it is not allowed to connect a voltage source to pin BOOST.
Electrostatic sensitive device. Observe precautions for handling.
6. Thermal Resistance
Parameters
Thermal resistance, junction ambient
Symbol
Value
Unit
RthJA
35
K/W
7. Operating Range
The operating conditions define the limits for functional operation and parametric characteristics of the device. Functionality outside these
limits is not implied if not otherwise stated explicitly.
Parameters
Operating supply voltage
Operating temperature range
10
Symbol
Value
Unit
VVBAT1
8 to 24
V
ϑ amb
–40 to +105
°C
ATA5276
4909C–AUTO–01/07
ATA5276
8. Noise and Surge Immunity
Parameter
Conducted interferences
Note:
Test Conditions
Value
ISO 7637-1
Level 4(1)
1. Test pulse 5: Vsmax = 45V
9. Electrical Characteristics(1)
No.
1
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
VCC
VCC
4.7
5.0
5.3
V
A
Power Supply
1.1
Main supply voltage
I(VCC) = 10 mA,
including load and line
regulation
1.2
Supply current
without antenna load
DVCC
ISUPP
2
10
20
mA
A
1.3
Standby current
Pin DVCC = 13.5V,
Tamb = 90°C
DVCC
ISTBY
20
35
60
µA
B
1.4
Power-on-reset
threshold voltage
VCC
VPOR
3.5
4
4.5
V
A
1.5
Load dump protection
voltage
DVCC
VBATLD
29
31
35
V
A
1.6
Under voltage
detection
DVCC
VBATUV
6.0
6.5
7.0
V
A
1.7
Thermal shut down
TSD
150
165
180
1.8
Protection debounce
filter
TDEB
10
15
2
o
C
B
25
µs
A
Half-bridge Driver Stage
2.1
Coil driver resistance
low side driver
DRV,
DVSS
RDSONL
0.3
0.7
Ω
A
2.2
Coil driver resistance
high side driver
DVCC,
DRV
RDSONH
0.3
0.7
Ω
A
Driver output rise time
10% to 90% slope
time,
0% = DVSS,
100% = DVCC
DVCC = 12V
(smooth edges)
DRV
TDRV,RISE
50
100
150
ns
D
Driver output fall time
10% to 90% slope
time,
0% = DVSS,
100% = DVCC
DVCC = 12V
(smooth edges)
DRV
TDRV,FALL
50
100
150
ns
D
2.3
2.4
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1. 8V < V(DVCC) < 24V; –40° C < ϑ amb < 105° C, unless otherwise specified; all values refer to GND
2. Definition of DCDRV see “Application Hints” on page 14
3. IVDIO,stby = 7.5 µA at Tamb = 90°C
11
4909C–AUTO–01/07
9. Electrical Characteristics(1) (Continued)
No.
3
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
85
%
B
Antenna Peak Current Control
3.1
Duty cycle control
range
DRV
DCDRV(2)
15
3.2
Peak current control
reference
RCR
VRCR
1.15
1.215
1.28
V
A
3.3
Peak current control
accuracy
RCR = 25 kΩ
IApeak
1.0
1.5
1.8
A
B
3.4
Antenna peak under
current threshold
0% NOM value = IAacc
RCR = 25 kΩ
IAUC
–30
–20
–10
%
A
3.5
Antenna peak
overcurrent threshold
0% NOM value = IAacc
RCR = 25 kΩ
IAOV
30
20
10
%
A
125
135
kHz
A
200
kHz
B
+120
ns
B
160
µs
D
4
Oscillator and Phase Control
4.1
VCO initial frequency
Self oscillating mode =
half-bridge not
activated
CLKSO
115
4.2
VCO frequency
tracking range
Tracking frequency
mode = half-bridge
activated
CLKTR
80
4.3
Phase shift between
voltage at DRV and
zero crossing of
current through
SENSE
Antenna resonance
frequency range =
100 kHz to150 kHz,
antenna quality = 5 to
50
DRV,
SENSE
ϕA
–120
4.4
Phase control set-up
time
–240 ns ≤ ϕA ≤
+240 ns
DRV,
SENSE
Tsetup
4.5
High frequency failure
threshold
DRV
fVCOH
150
160
200
kHz
A
4.6
Low frequency failure
threshold
DRV
fVCOL
80
90
105
kHz
A
5
0
DIO Interface
5.1
VDIO leakage current
Pin VDIO = 13.5V,
Pin DIO = 13.5V
Tamb ≤ 27°C(3)
VDIO
IVDIO,STBY
2
4
5
µA
A
5.2
DIO leakage current
Pin VDIO = 13.5V,
Pin DIO = 13.5V
Tamb = 90°C
DIO
IDIO,LEAK
5.5
10
15
µA
A
5.3
DIO sink current
DIO
IDIO,LIMIT
36
44
52
mA
A
5.4
Output low level
IDIO = 20 mA
DIO
VDIOL
1.2
1.5
V
A
5.5
Input low level
threshold
100% = DVCC
DIO
VDIO,THL
30
45
70
%V
(VDIO)
A
5.6
Input high level
threshold
100% = DVCC
DIO
VDIO,TLH
30
50
70
%V
(VDIO)
A
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1. 8V < V(DVCC) < 24V; –40° C < ϑ amb < 105° C, unless otherwise specified; all values refer to GND
2. Definition of DCDRV see “Application Hints” on page 14
3. IVDIO,stby = 7.5 µA at Tamb = 90°C
12
ATA5276
4909C–AUTO–01/07
ATA5276
9. Electrical Characteristics(1) (Continued)
No.
6
Parameters
Test Conditions
Pin
Symbol
Min.
Typ.
Max.
Unit
Type*
4
kbit/s
C, D
Transmission Protocol
6.1
LF data baud rate
BdRF
1
6.2
Anti-bouncing time for
activate half-bridge
DIO = H → L,
for fVCO = 125 kHz
TDL
64
µs
B
6.3
Anti-bouncing time for
de-activate half-bridge
DIO = L → H,
for fVCO = 125 kHz
TDH
64
µs
B
6.4
Acknowledge pulse
width
TACK
256
µs
B
6.5
Error signal pulse
width
TERR
128
µs
B
6.6
Transmission time out
de-activated
half-bridge
TOUTL
16
ms
B
6.7
Transmission time out
activated half-bridge
TOUTH
16
ms
6.8
Time out reset pulse
width
TOR
32
µs
6.9
Time out reset pulse
period
TORP
15
ms
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Notes:
1. 8V < V(DVCC) < 24V; –40° C < ϑ amb < 105° C, unless otherwise specified; all values refer to GND
2. Definition of DCDRV see “Application Hints” on page 14
3. IVDIO,stby = 7.5 µA at Tamb = 90°C
10. External Components
The following external components have to be applied to the circuit for functional operation (see Figure 11-1 on page 15).
Component
Pin
C1
Min.
DVCC
D1 standard diode
REXT
REXT
RCR
RCR
(3)
C3
VCC
C2
BOOST
SENSE
DIO
RDIO
LANT antenna inductance
RANT Q-factor adjuster
CANT resonant-frequency adjuster
Notes:
Max.
1.5/50
A/V
100
kΩ
25
0.68
(2)
0.1
0.6
Unit
µF/V
200
10
(1)
RSENSE
Typ.
100/50
kΩ
µF
1
2
nF
0.5
1
Ω
1
6
kΩ
345/2.5
µH/Ω
10
Ω
4.7/400
nF/V
1. Sensitivity at input SENSE is proportional to resistor Rs times antenna peak current.
2. For antenna peak value 1.5A.
3. Recommended range: RCR = 25 to 100 kΩ.
13
4909C–AUTO–01/07
11. Application Hints
A typical application of ATA5276 is shown in Figure 11-1 on page 15. The peak value of the
antenna current can be estimated by the formula:
π
2 V DVCC
Î A = --- × ----------------- × sin ⎛ --- × DC DRV⎞ × cosϕA
⎝2
⎠
π
RA
Here RA denotes the equivalent series resistance of the driver load, i.e., the external coil series
resistance in series with the shunt resistance and the internal drain-source-on-resistance of the
NDMOS. The duty cycle DCDRV is the ratio of the driver high-side on-time with respect to the half
of the oscillation period.
The phase difference ϕA is measured as the time difference between the point of mass of VDRV
and the peak value of the antenna current.
14
ATA5276
4909C–AUTO–01/07
8V to 24V
D1
+ C1
C2
DVCC3
20
RDIO
+ C3
DRV
GND
VCC
BOOST
19
DVCC2 1
17
5V
Reg.
VDIO
DIO
18
References
CDIO
16
RefExt
KLine
15
TM1
14
TM2
13
TM3
12
RCR
Microcontroller
or
ECU
BUS
State
Machine
DVCC1 2
ATA5276
CANT
Gate
Driver
Control
DRV3 3
Half
Bridge
125 kHz Transmitter
Current
Sense
DRV2 4
ON/
LF Receiver
LANT
CLK
OFF
Figure 11-1. Application Circuit
4909C–AUTO–01/07
VBATT
DRV
Duty
Cycle
Regulator
VCO
RCR
11
DRV1 5
RS
REXT
REXT
6
7
DVSS3
8
DVSS2
9
DVSS1
10
SENSE
VSS
RSHUNT
15
ATA5276
Note: For the typical values of the external components, see table "External Components" on page 13.
12. Ordering Information
Extended Type Number
Package
Remarks
Minimum Order Quantitiy
ATA5276M-PGQW
QFN20, 5 mm × 5 mm
Pb-free, Taped and reeled
6,000
ATA5276M-PGPW
QFN20, 5 mm × 5 mm
Pb-free, Taped and reeled
1,500
13. Package Information
16
ATA5276
4909C–AUTO–01/07
ATA5276
14. Revision History
Please note that the following page numbers referred to in this section refer to the specific revision
mentioned, not to this document.
Revision No.
History
4909C-AUTO-01/07
•
•
•
•
•
•
•
•
•
Put datasheet in a new template
All pages: Preliminary deleted
Page 1: Application: new bullets added
Page 1: Benefits: new bullet added
Page 2: General Description: text changed
Page 8: Coil Driver Output... last paragrah changed
Page 10: Abs.Max.Rat. Table: Minimum ESD protection rows changed
Page 15: Application Ciruit drawing changed
Page 16: Ordering Information Table changed
17
4909C–AUTO–01/07
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Atmel Operations
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-47-50
Fax: (33) 4-76-58-47-60
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
Literature Requests
www.atmel.com/literature
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided
otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use
as components in applications intended to support or sustain life.
© 2007 Atmel Corporation. All rights reserved. Atmel ®, logo and combinations thereof, Everywhere You Are® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
4909C–AUTO–01/07