ATA5795C-PNQW18

ATA5795C Embedded AVR Microcontroller Including RF Transmitter and Immobilizer LF Functionality for Remote Keyless Entry DATASHEET Features ● System solution for immobilizer and remote keyless entry functionality ● Optional integrated open source immobilizer software stack supports automotive immobilizer applications (CMMI certified) ● Integrated ultra-low power flash Atmel® AVR® (8-bit) microcontroller ● 2112-byte EEPROM ● 32-bit unique device identification number ● Available in small 5x5 QFN32 pin package Contactless Transponder ● LF contactless transponder operation in passive and active modes ● Integrated codecs for enhanced LF communication range ● Ultra low-power AES-128 cryptographic engine for use of immobilizer and RKE applications ● Access protected area for two 128-bit secret keys for device authentication ● Optional one 128-bit transport key for initial configuration ● LF receiver data integrity check (CRC-4/CRC-8) RF Transmitter ● Fully integrated fractional-N PLL, VCO and loop filter covering 315MHz and 433MHz (software programmable) ● Output power programmable from –0.5 to +12.5dBm ● Supports ASK and FSK modulation with data rate up to 40Kbit/s ● Extended battery lifetime due to fast start-up time, low operating voltage and low supply current This is a summary document. The complete document is available under NDA. For more information, please contact your local Atmel sales office. 9182ES-RKE-11/14 Ultra-low-power AVR Microcontroller ● 8Kbyte flash program memory (including 2KB of immobilizer software stack) ● 2112-byte EEPROM – includes protected user data and device configuration data (64Bytes) ● Error correction code (ECC) engine protects flash and EEPROM ● 512Bytes of SRAM ● Four GP timers ● ● ● ● T0: Flexible WD and interval timers T1: 15-bit interval timer T2: Asynchronous 8-bit timer/counter with output compare T3: Asynchronous 8-bit timer/counter with output compare and input capture ● Power management unit ● System clock management and monitoring functions ● POR and brown-out detection ● Programmable voltage monitor ● RTC and two internal system clock RC oscillators with f1 = 125kHz, f2 = 4MHz ● SPI, TM/SSI, IR digital interfaces; dW 1-wire debug IF with AVR development tools ● Very low power consumption: ● ● ● ● Active: 50µA (Sys_Clk at 125kHz) Idle: < 70µA (Sys_Clk at 1MHz) Power-down: 0.8µA EE(wr): 50µA ● Wide battery voltage range from 1.9 to 3.6V (in contact mode) ● –40 to +85°C operation temperature ● Automotive grade C compiler 2 ATA5795C [DATASHEET] 9182ES–RKE–11/14 1. Description Atmel® ATA5795C is a smart remote keyless entry (RKE) device that includes an embedded ultra-low-power AVR® 8-bit microcontroller, a fractional-N RF transmitter and an LF immobilizer interface in a single QFN32 package. Furthermore, the device has an integrated AES-128 cryptography hardware engine, which is accessible by both the immobilizer and the RKE unit. The immobilizer interface can run in contactless mode, allowing energy supply and data transmission via the LF link. The Atmel ATA5795C is designed for automotive applications that necessitate both immobilization and remote keyless entry functions in one single key. It conforms to requirements of extremely low power consumption and provides all the necessary circuitry for the entire application. 1.1 System Block Diagram Figure 1-1. System Block Diagram Key Battery Car VBAT RF CBUF AVR T-Coil 16 15 14 13 12 11 10 9 17 8 18 7 19 6 RF-Receiver: 5 ATA5723/24/28 ATA5780 20 21 RFLoop antenna ATA5795C 4 22 3 23 2 24 1 25 26 27 28 29 30 31 32 Transponder Base Station: U2270, ATA5272 ATA5795C [DATASHEET] 9182ES–RKE–11/14 3 1.2 Atmel ATA5795C Block Diagram A4P A4N Power Management SPI AFE EEPROM/ 2.1KB Contactless Interface/ Transponder VSRF VCC VBAT Figure 1-2. Atmel ATA5795C Block Diagram ECIN FRC-Oscillator Clock Management and Monitoring RTC XTO XTO1 XTO2 Frac.-N PLL PC0 Watchdog Oscillator Volt. Monitor PD7/TM3 RF-Transmitter AVR-Core VCO PD6/TM2 PD5/TM1 Watchdog Timer IR-Driver PD3 PD1/T3ICP SRAM/512B Flash/8KB Timer Block PD0/INT0 PB0/NSS TME PB1/SCK PB7 IO-Ports GND PB2/MOSI PB6 PB4/TM4 PB3/MISO CRC-Module XTO2 1.3 PB5/TM5 Crypto Unit PB7 XTAL1 Digital Control DebugWIRE PB6 XTAL2 Pin Configurations PB2 PB1 ANT2 ANT1 PB0 Figure 1-3. Pin Out for QFN 32 Package 32 31 30 29 28 27 26 25 TME 1 24 PB3 XTO1 2 23 PD3 VSRF 3 22 PD4 GNDRF 4 21 PD5 NRESET 5 20 PD6 PC0 6 19 PD7 A4N 7 18 PB4 A4P 8 17 PB5 Atmel ATA5795C ATA5795C [DATASHEET] 9182ES–RKE–11/14 XTAL2 GND VCC XTAL1 PD2 PD1 PD0 VBAT 9 10 11 12 13 14 15 16 4 Power Amplifier POR/BOD and Reset NRESET(DW) PD2/TEI GNDRF PD4/ECIN0 ANT1 ANT2 Table 1-1. Pin Description Pin Number Pin Name Alternate Function 1 Alternate Function 2 Function 1 TME - - Test mode enable 2 XTO1 - - Connection for RF crystal RF - pin 3 VSRF - - Power supply voltage RF RF - pin 4 GNDRF - - Power supply ground RF RF - pin 5 NRESET dW - Reset input / debugWire interface 6 PC0 - - I/O port 7 A4N - - Input pin for transponder AFE 8 A4P - - Input pin for transponder AFE 9 VBAT - - Power supply voltage for battery 10 PD0 INT0 PCINT8 I/O port / external interrupt input 0 Port D0 11 PD1 T3ICP PCINT9 I/O port / timer 3 external capture input Port D1 12 PD2 TEI PCINT10 I/O port / external timer input clock Port D2 Comment Port C0 13 VCC - - Power supply voltage for the microcontroller. A capacitor with capacitance CBUF must be connected at this pin to buffer the voltage during field supply and block the microcontroller VCC. 14 XTAL1 - - 32kHz crystal oscillator input pin 15 GND - - Power supply ground 16 XTAL2 - - 32kHz crystal oscillator output pin 17 PB5 TM5 PCINT5 I/O port / timer modulator pin 5 Port B5 18 PB4 TM4 PCINT4 I/O port / timer modulator pin 4 Port B4 19 PD7 TM3 PCINT15 I/O port / timer modulator pin 3 Port D7 20 PD6 TM2 PCINT14 I/O port / timer modulator pin 2 Port D6 21 PD5 TM1 PCINT13 I/O port / timer modulator pin 1 Port D5 22 PD4 ECIN0 PCINT12 I/O port / external clock input 0 Port D4 23 PD3 - PCINT11 I/O port Port D3 24 PB3 MISO PCINT3 I/O port / SPI Port B3 25 PB2 MOSI PCINT2 I/O port / SPI Port B2 26 PB1 SCK PCINT1 I/O port / SPI Port B1 27 ANT2 - - RF antenna 2 RF - pin 28 ANT1 - - RF antenna 1 RF - pin 29 PB0 NSS PCINT0 I/O port / SPI Port B0 30 PB7 - PCINT7 I/O port Port B7 31 PB6 - PCINT6 I/O port Port B6 32 XTO2 - - Connection for RF crystal RF - pin ATA5795C [DATASHEET] 9182ES–RKE–11/14 5 2. Ordering Information Extended Type Number Package ATA5795C-PNQW 3. Remarks QFN32 - 5x5 Pb-free, 6k Package Information Top View D 32 1 technical drawings according to DIN specifications E PIN 1 ID 8 A Side View A3 A1 Dimensions in mm Bottom View D2 9 16 17 E2 8 1 Z 24 32 e 25 COMMON DIMENSIONS (Unit of Measure = mm) L Z 10:1 b Symbol MIN NOM MAX A 0.8 0.85 0.9 A1 A3 0 0.16 0.035 0.21 0.05 0.26 D 4.9 5 5.1 D2 3.5 3.6 3.7 E 4.9 5 5.1 E2 3.5 3.6 3.7 L 0.35 0.4 0.45 b e 0.2 0.25 0.5 0.3 NOTE 05/20/14 TITLE Package Drawing Contact: packagedrawings@atmel.com 6 ATA5795C [DATASHEET] 9182ES–RKE–11/14 Package: QFN_5x5_32L Exposed pad 3.6x3.6 GPC DRAWING NO. REV. 6.543-5203.01-4 1 4. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 9182ES-RKE-11/14 History • Section 2 “Ordering Information” on page 6 updated • Section 3 “Package Information” on page 6 updated 9182DS-RKE-04/14 • Put datasheet in the latest template 9182CS-RKE-11/11 • ATA5795 to ATA5795C renamed 9182BS-RKE-07/11 • Document completely redesigned ATA5795C [DATASHEET] 9182ES–RKE–11/14 7 XXXXXX Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2014 Atmel Corporation. / Rev.: 9182ES–RKE–11/14 Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.