ATmega88/168 Automotive
Appendix A - Atmel ATmega88/168 Automotive
Specification at 150°C
DATASHEET
Description
This document contains information specific to devices operating at temperatures up to
150°C. Only deviations are covered in this appendix, all other information can be found in
the complete Automotive datasheet. The complete Automotive datasheet can be found on
http://www.atmel.com
7607J-AVR-07/14
1.
Electrical Characteristics
1.1
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Operating temperature
Storage temperature
Voltage on any pin except RESET with respect to ground
Voltage on RESET with respect to ground
Test Conditions
Unit
–55 to +150
°C
–65 to +175
°C
–0.5 to VCC+0.5
V
–0.5 to +13.0
V
6.0
V
30
200.0
mA
Maximum operating voltage
DC current per I/O pin
DC current VCC and GND
1.2
DC Characteristics
TA = –40°C to +150°C, VCC = 2.7V to 5.5V (unless otherwise noted)
Parameters
Test Conditions
Symbol
Min.
Input low voltage, except
XTAL1 and RESET pin
VCC = 2.7V to 5.5V
VIL
Input high voltage, except
XTAL1 and RESET pins
VCC = 2.7V to 5.5V
Input low voltage,
XTAL1 pin
Max.
Unit
–0.5
+0.3VCC(1)
V
VIH
0.6VCC(2)
VCC + 0.5
V
VCC = 2.7V to 5.5V
VIL1
–0.5
+0.1VCC(2)
V
Input high voltage,
XTAL1 pin
VCC = 2.7V to 5.5V
VIH1
0.7VCC(2)
VCC + 0.5
V
Input low voltage,
RESET pin
VCC = 2.7V to 5.5V
VIL2
–0.5
+0.2VCC(1)
V
VCC + 0.5
V
Input high voltage,
VCC = 2.7V to 5.5V
VIH2
0.9VCC(2)
RESET pin
Notes: 1. “Max” means the highest value where the pin is guaranteed to be read as low
Typ.
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V) under steady state conditions
(non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOL, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current
greater than the listed test condition.
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V) under steady state conditions
(non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 400mA.
2] The sum of all IOH, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOH, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum VCC for Power-down is 2.5V
2
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
1.2
DC Characteristics (Continued)
TA = –40°C to +150°C, VCC = 2.7V to 5.5V (unless otherwise noted)
Parameters
Test Conditions
Symbol
Min.
Input low voltage,
RESET pin as I/O
Typ.
Max.
Unit
VCC = 2.7V to 5.5V
VIL3
–0.5
+0.3VCC(1)
V
Input high voltage,
RESET pin as I/O
VCC = 2.7V to 5.5V
VIH3
0.6VCC(2)
VCC + 0.5
V
Output low voltage(3),
I/O pin except RESET
IOL = 20mA, VCC = 5V
IOL = 5mA, VCC = 3V
VOL
0.8
0.5
V
Output high voltage(4)
I/O pin except RESET
IOH = –20mA, VCC = 5V
IOH = –10mA, VCC = 3V
VOH
Input leakage
current I/O pin
VCC = 5.5V, pin low
(absolute value)
IIL
1
µA
Input leakage current I/O
pin
VCC = 5.5V, pin high
(absolute value)
IIH
1
µA
4.0
2.2
V
Reset pull-up resistor
RRST
30
60
k
I/O pin pull-up resistor
RPU
20
50
k
8
16
mA
25
mA
6
12
mA
Idle 16MHz, VCC = 5V
14
mA
WDT enabled, VCC = 3V
WDT enabled, VCC = 5V
90
140
µA
80
120
µA
40
mV
+50
nA
Active 4MHz, VCC = 3V
Active 8MHz, VCC = 5V
Power supply current(5)
Power-down mode
ICC
Active 16MHz, VCC = 5V
Idle 4MHz, VCC = 3V
Idle 8MHz, VCC = 5V
WDT disabled, VCC = 3V
WDT disabled, VCC = 5V
ICC IDLE
ICC PWD
Analog comparator
input offset voltage
VCC = 5V
Vin = VCC/2
VACIO
Analog comparator
input leakage current
VCC = 5V
Vin = VCC/2
IACLK
< 10
–50
Analog comparator
VCC = 4.0V
tACPD
500
propagation delay
Notes: 1. “Max” means the highest value where the pin is guaranteed to be read as low
ns
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V) under steady state conditions
(non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOL, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current
greater than the listed test condition.
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V) under steady state conditions
(non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 400mA.
2] The sum of all IOH, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOH, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum VCC for Power-down is 2.5V
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
3
1.3
Memory Endurance
EEPROM endurance: 50,000 write/erase cycles.
Flash endurance: 10,000 write/erase cycles.
1.4
Maximum Speed versus VCC
Maximum frequency is dependent on VCC. As shown in Figure 1-1, the maximum frequency versus VCC curve is linear
between 2.7V < VCC < 4.5V.
Figure 1-1. Maximum Frequency versus VCC
16MHz
8MHz
Safe Operating Area
2.7V
4.5V
5.5V
)
1.5
ADC Characteristics(1)
TA = –40°C to +150°C, VCC = 4.5V to 5.5V (unless otherwise noted)
Parameters
Test Conditions
Symbol
Min
Resolution
Typ
Max
10
Unit
Bits
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
2
3.5
LSB
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
Noise reduction mode
2
3.5
LSB
Integral non-linearity (INL)
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
0.6
2.5
LSB
Differential non-linearity
(DNL)
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
0.30
1.0
LSB
Gain error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
–1.3
+3.5
LSB
Offset error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
1.8
3.5
LSB
Conversion time
Free running conversion
Absolute accuracy
(including INL, DNL,
quantization error, gain and
offset error)
–3.5
13 cycles
Clock frequency
µs
50
200
kHz
VCC – 0.3
VCC + 0.3
V
Analog supply voltage
AVCC
Reference voltage
VREF
1.0
AVCC
V
VIN
GND
VREF
V
Input voltage
Input bandwidth
38.5
kHz
Internal voltage reference
VINT
1.0
1.1
1.2
Reference input resistance
RREF
25.6
32
38.4
Analog input resistance
RAIN
100
Note:
1. Based on standard voltage range (2.7V to 5.5V) characterization results. To be confirmed after actual silicon
characterization.
4
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
V
k
M
2.
ATmega88/168 Typical Characteristics
2.1
Active Supply Current
Figure 2-1. Active Supply Current versus Frequency (1MHz to 20MHz)
16
5.5V
14
5.0V
ICC (mA)
12
10
8
3.3V
3.0V
6
4
2
0
0
2
4
6
8
10
12
16
14
18
20
Frequency (MHz)
Figure 2-2. Idle Supply Current versus Frequency (1MHz to 20MHz)
8
ICC (mA)
6
4
5.5V
5.0V
2
3.3V
3.0V
0
4
6
8
10
12
14
16
18
20
Frequency (MHz)
2.2
Power-Down Supply Current
Figure 2-3. Power-down Supply Current versus VCC (Watchdog Timer Disabled)
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
5
Figure 2-4. Power-down Supply Current versus VCC (Watchdog Timer Enabled)
35
150°C
30
ICC (µA)
25
20
15
125°C
10
-40°C
85°C
25°C
5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
2.3
Pin Pull-up
Figure 2-5. I/O Pin Pull-up Resistor Current versus Input Voltage (VCC = 5V)
160
150°C
140
IOP (µA)
120
-40°C
100
80
60
40
20
0
0
1
2
3
4
5
6
VOP (V)
Figure 2-6. Output Low Voltage versus Output Low Current (VCC = 5V)
0.8
0.7
150°C
125°C
0.6
VOL (V)
85°C
0.5
25°C
0.4
-40°C
0.3
0.2
0.1
0
0
2
4
6
8
10
IOL (mA)
6
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
12
14
16
18
20
Figure 2-7. Output Low Voltage versus Output Low Current (VCC = 3V)
1.4
1.2
150°C
125°C
VOL (V)
1.0
85°C
0.8
25°C
0.6
-40°C
0.4
0.2
0
0
2
4
6
8
10
12
14
16
18
20
IOL (mA)
Figure 2-8. Output High Voltage versus Output High Current (VCC = 5V)
5.2
5.0
VOH (V)
4.8
4.6
-40°C
25°C
85°C
125°C
150°C
4.4
4.2
4
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
Figure 2-9. Output High Voltage versus Output High Current (VCC = 3V)
3.5
3.0
Current (V)
2.5
-40°C
25°C
85°C
125°C
150°C
2.0
1.5
1.0
0.5
0
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
7
Figure 2-10. Reset Pull-up Resistor Current versus Reset Pin Voltage (VCC = 5V)
140
IRESET (µA)
120
150°C
100
80
-40°C
60
40
20
0
0
1
2
3
4
5
6
VRESET (V)
2.4
Pin Thresholds and Hysteresis
Figure 2-11. I/O Pin Input Threshold versus VCC (VIH, I/O Pin Read as ‘1’)
3
150°C
-40°C
2.5
VIH (V)
2.0
1.5
1.0
0.5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-12. I/O Pin Input Threshold versus VCC (VIL, I/O Pin Read as ‘0’)
3
150°C
-40°C
2.5
VIL (V)
2.0
1.5
1.0
0.5
0
2.5
3
3.5
4
VCC (V)
8
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
4.5
5
5.5
Figure 2-13. Reset Input Threshold Voltage versus VCC (VIH, Reset Pin Read as ‘1’)
3
Threshold (V)
2.5
2.0
-40°C
1.5
1.0
150°C
0.5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 2-14. Reset Input Threshold Voltage versus VCC (VIL, Reset Pin Read as ‘0’)
2.5
Threshold (V)
2.0
1.5
150°C
-40°C
1.0
0.5
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Internal Oscillator Speed
Figure 2-15. Watchdog Oscillator Frequency versus VCC
190
170
FRC (kHz)
2.5
150
2.7V
3.0V
5.0V
5.5V
130
110
90
70
-40 -30 -20 -10 0 10
20 30
40 50 60 70
80 90 100 110 120 130 140 150 160
Temperature
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
9
Figure 2-16. Calibrated 8MHz RC Oscillator Frequency versus Temperature
8.4
5.5V
5.0V
4.5V
3.3V
3.0V
2.7V
8.3
FRC (MHz)
8.2
8.1
8.0
7.9
7.8
7.7
7.6
-40 -30 -20 -10
0 10
20 30 40 50
60 70 80 90 100 110 120 130 140 150
Temperature
Figure 2-17. Calibrated 8MHz RC Oscillator Frequency versus VCC
8.4
150°C
8.3
125°C
FRC (MHz)
8.2
85°C
8.1
25°C
8.0
-40°C
7.9
7.8
7.7
7.6
2
2.5
3
3.5
4
4.5
5
5.5
6
VCC (V)
Figure 2-18. Calibrated 8MHz RC Oscillator Frequency versus OSCCAL Value
16
150°C
-40°C
14
FRC (MHz)
12
10
8
6
4
2
0
0
16
32
48
64
80
96 112 128 144 160 176 192 208 224 240 256
OSCCAL (X1)
10
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
BOD Thresholds and Analog Comparator Offset
Figure 2-19. BOD Threshold versus Temperature (BODLEVEL is 4.0V)
4.6
Threshold (V)
4.5
4.4
1
4.3
0
4.2
4.1
4.0
-50 -40 -30 -20 -10 0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
Temperature (°C)
Figure 2-20. BOD Threshold versus Temperature (BODLEVEL is 2.7V)
3.0
Threshold (V)
2.9
2.8
1
2.7
0
2.6
2.5
2.4
-50 -40 -30 -20 -10 0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
Temperature (°C)
Figure 2-21. Bandgap Voltage versus VCC
1.25
Bandgap Voltage (V)
2.6
1.20
1.15
1.10
150°C
-40°C
1.05
1.00
0.95
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
11
2.7
Peripheral Units
Figure 2-22. Analog to Digital Converter GAIN versus VCC
0
Error (LSB)
-0.5
-1.0
4 IDL
-1.5
4 STD
-2.0
-2.5
-50
-25
0
25
50
75
100
125
150
Temperature
Figure 2-23. Analog to Digital Converter OFFSET versus VCC
2.5
4 IDL
Error (LSB)
2.0
4 STD
1.5
1.0
0.5
0
-50
-25
0
25
50
75
100
125
150
Temperature
Figure 2-24. Analog to Digital Converter DNL versus VCC
1.0
0.9
Error (LSB)
0.8
0.7
0.6
0.5
0.4
4 IDL
0.3
4 STD
0.2
0.1
0
-50
-25
0
25
50
75
Temperature
12
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
100
125
150
Figure 2-25. Analog to Digital Converter INL versus VCC
1.0
0.9
Error (LSB)
0.8
0.7
0.6
4 IDL
0.5
4 STD
0.4
0.3
0.2
0.1
0
-50
-25
0
25
50
75
100
125
150
Temperature
Grade 0 Qualification
The ATmega88/168 has been developed and manufactured according to the most stringent quality assurance requirements
of ISO-TS-16949 and verified during product qualification as per AEC-Q100 grade 0.
AEC-Q100 qualification relies on temperature accelerated stress testing. High temperature field usage however may result
in less significant stress test acceleration. In order to prevent the risk that ATmega88/168 lifetime would not satisfy the
application end-of-life reliability requirements, Atmel® has extended the testing, whenever applicable (High Temperature
Operating Life Test, High Temperature Storage Life, Data Retention, Thermal Cycles), far beyond the AEC-Q100
requirements. Thereby, Atmel verified the ATmega88/168 has a long safe lifetime period after the grade 0 qualification
acceptance limits.
The valid domain calculation depends on the activation energy of the potential failure mechanism that is considered.
Examples are given in Figure 2-26. Therefore any temperature mission profile which could exceed the AEC-Q100
equivalence domain shall be submitted to Atmel for a thorough reliability analysis.
Figure 2-26. AEC-Q100 Lifetime Equivalence
1000000
100000
10000
Hours
2.8
1000
100
10
1
0
20
40
60
80
100
120
140
160
Temperature (°C)
HTOL 0.59eV
HTSL 0.45eV
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
13
3.
Ordering Information
Table 3-1.
Speed (MHz)
Power Supply
Ordering Code
Package(1)
Operation Range
16(2)
2.7V to 5.5V
ATmega88-15MT2
PN
Extended (–40C to +150C)
16(2)
2.7V to 5.5V
ATmega88-15AD
MA
Extended (–40C to +150C)
16
(2)
2.7V to 5.5V
ATmega168-15MD
PN
Extended (–40C to +150C)
16
(2)
2.7V to 5.5V
ATmega168-15AD
MA
Extended (–40C to +150C)
Notes:
4.
ATmega88/168
1.
Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also halide free and fully green.
2.
For speed versus Vcc, see complete datasheet.
Package Information
Table 4-1.
Package Types
Package Type
14
PN
32-pad, 5 5 1.0mm body, lead pitch 0.50mm, quad flat no-lead/micro lead frame package (QFN/MLF): E2/D2
3.1 ±0.1mm
MA
32 - Lead, 7mm 7mm body size, 1.0mm body thickness 0.8mm lead pitch, thin profile plastic quad flat package
(TQFP)
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
Figure 4-1. PN
Drawings not scaled
A
A3
D
A1
N
1
0.30
Dia. Typ. Laser Marking
E
Seating Plane
C
0.080 C
Top View
L
Side View
D2
COMMON DIMENSIONS
b
(Unit of Measure = mm)
Option A
Pin 1# Chamfer
(C 0.30)
E2
Option B
PIN1 ID
1
Pin 1# Notch
(C 0.20 R)
See Options
A, B
e
Symbol
MIN
NOM
MAX
A
0.80
0.85
0.90
A1
A3
0.00
NOTE
0.05
0.20 REF
D/E
5.00 BSC
D2/E2
3.00
3.10
3.20
L
0.30
0.40
0.50
b
0.18
0.25
0.30
e
0.50 BSC
n
32
2
Bottom View
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-220, Variation VHHD-2, for proper dimensions, tolerances, datums, etc.
2. Dimensions b applies to metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip.
If the terminal has the optical radius on the other end of the terminal, the dimensions should not be measured in that radius area.
01/31/12
Package Drawing Contact:
packagedrawings@atmel.com
TITLE
GPC
DRAWING NO.
REV.
PN, 32 Leads - 0.50mm Pitch, 5x5mm
Very Thin Quad Flat no Lead Package (VQFN) Sawn
ZMF
PN
I
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
15
Figure 4-2. MA
Drawings not scaled
A
A2
A1
D1
32
1
E1
e
L
0°~7°
Top View
C
Side View
D
COMMON DIMENSIONS
(Unit of Measure = mm)
Symbol
MIN
NOM
A
MAX
1.20
A1
0.05
A2
0.95
1.00
D/E
8.75
9.00
9.25
D1/E1
6.90
7.00
7.10
E
b
Bottom View
NOTE
0.15
1.05
C
0.09
0.20
L
0.45
0.75
b
0.30
2
0.45
e
0.80 TYP.
n
32
Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MS-026, Variation ABA.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25mm per side.
Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10mm maximum.
02/29/12
Package Drawing Contact:
packagedrawings@atmel.com
16
TITLE
GPC
DRAWING NO.
REV.
MA, 32 Lds - 0.80mm Pitch, 7x7x1.00mm Body size
Thin Profile Plastic Quad Flat Package (TQFP)
AUT
MA
C
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
5.
Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this
document.
Revision No.
History
7607J-AVR-07/14
Put datasheet in the latest template
7607I-AVR-03/12
Section 4 “Package Information” on pages 15 to 16 changed
7607H-AVR-02/10
Table 4-1 “Package Types” on page 15 changed
7607G-AVR-07/09
Package MA updated
7607F-AVR-01/08
Added memory endurance. See Section 1.3 “Memory Endurance” on page 4
7607E-AVR-11/07
Added ATMega168 product offering
Added MA package offering
Updated electrical characteristics
7607D-AVR-03/07
Removed Grade0 qualification section
Updated product part number in ordering information
7607C-AVR-09/06
Ordering and package information updated
7607B-AVR-08/06
Added typical characteristics
7607A-AVR-01/06
Document Creation
ATmega88/168 Automotive [DATASHEET]
7607J–AVR–07/14
17
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2014 Atmel Corporation. / Rev.: 7607J–AVR–07/14
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, and others are registered trademarks or trademarks of Atmel Corporation in U.S.
and other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Atmel:
ATMEGA168-15MD
工商网监
湘ICP备2023018690号
