ATXPRO-10PIN

USER GUIDE 10Pin XPRO Adapter Atmel MCU Wireless Features • • • • Enables Atmel Legacy platforms to use newer ZigBit® Extensions. Supports RF-only ZigBits, SoC ZigBits and RF Extensions. On board current measurement header. Minimal jumper configuration. 42207A−WIRELESS−10/2013 Table of Contents 1. Introduction ........................................................................................ 3 1.1 1.2 Summary ........................................................................................................... 3 Supported kits containing 10 pin Headers......................................................... 3 2. Specifications ..................................................................................... 3 2.1 2.2 2.3 2.4 Pin Configuration............................................................................................... 3 Jumper Settings ................................................................................................ 4 Current Measurement ....................................................................................... 5 Schematics ....................................................................................................... 5 3. Revision History ................................................................................. 6 10Pin XPRO Adapter [USER GUIDE] 42207A−WIRELESS−10/2013 2 1. Introduction 1.1 Summary ATXPRO-10PIN is a 10- to 20-pin adaptor that facilitates to connect new 20-pin Zigbits extensions and RF extensions to legacy 10-pin headers on SAM-EKs, STK®600, Xplained kits. The 10-pin header on legacy kits refers to the RF header where RZ600 fits. The supported 20-pin extensions includes RF only ZigBit extension, SoC ZigBit extension and REB233-XPRO. 1.2 Supported Kits Containing 10 Pin Headers 1. SAM4E-EK 4. SAM4L-EK 7. XMEGA® A3BU Xplained 10. SAM4S-XPLD 2. SAM3X-EK 5. SAM4S-EK2 8. XMEGA B1 Xplained 11. Mega1284P Xplained 3. SAM3S-EK 6. SAM3N-EK 9. XMEGA A1 Xplained 12. STK600 2. Specifications 2.1 Pin Configuration Pin No. 20-pin Connector (J3) Pin No. 10-pin Connector (J1) 1 ID_DATA 1 RST 2 GND 2 MISC IO 3 ADC(+) 3 IRQ 4 ADC(-) 4 SLP_TR 5 GPIO 5 SEL/SPI_CS 6 GPIO 6 MOSI 7 PWM(+) 7 MISO 8 PWM(-) 8 SCLK/SPCK 9 IRQ/GPIO 9 GND 10 SPI_SS_B/GPIO 10 VCC 11 TWI_SDA 12 TWI_SCL 13 UART_RX Note: Refer datasheets of the selected evaluation board or XPRO extension for details on the signal names mentioned in above tables. 14 UART_TX 15 SPI_SS_A 16 SPI_MOSI 17 SPI_MISO 18 SPI_SCK 19 GND 20 VCC_TARGET 10Pin XPRO Adapter [USER GUIDE] 42207A−WIRELESS−10/2013 3 2.2 Jumper Settings For REB233-XPRO and RF only Zigbits, jumper settings for J4 and J2 are as shown in Figure 2-1. Figure 2-1. ATXPRO-10PIN for REB233-XPRO and RF only ZigBits For SoC Zigbits, jumper settings for J4 and J2 are as shown in Figure 2-2. 10Pin XPRO Adapter [USER GUIDE] 42207A−WIRELESS−10/2013 4 Figure 2-2. ATXPRO-10PIN for SoC ZigBits 2.3 Current Measurement Header J5 is the current measurement header which enables user to measure current consumed by the extension modules. When ‘J5’ is not used for current measurement, the jumper should be placed on it. 2.4 Schematics The schematic of the 10-pin to 20-pin Adaptor is shown below. 10Pin XPRO Adapter [USER GUIDE] 42207A−WIRELESS−10/2013 5 1 2 A 3 4 COJS1 JS1 COJS2 JS2 To be used by request from ESCATEC SNT-100-BK-G To be used by request from ESCATEC SNT-100-BK-G IRQ/RXD IRQ SLP_TR/TXD UART_RX SPI_SS_B/GPIO/SLP_TR 3 2 1 PIJ403 PIJ402 PIJ401 3 2 1 PIJ203 PIJ20 PIJ201 UART_TX COJ2 J2 COJ4 J4 HEADER 1x3 CD075014 1X3 HEADER 1x3 CD075014 1X3 10-Pin/EVK Side 5 6 A Note: 1. ID_DATA has no connection to 10-pin Connector 2. ADC+/NC/DIG1, ADC-/DIG2, TWI_SDA, TWI_SCL, UART_RX and UART_TX have no connection to 10-pin connector, except(UART_RX and UART_TX were used for some kits) 3. CSD has Pull down on RF-only Zigbits. SPI_SS/SEL SPI_MOSI SPI_MISO SPI_SCK B RST# PWM+/RST# MISC PWM-/FEM_SEL/CPS 8 Note: For some of these kits pin3 and pin4 of 10pin Connector has UART interface connected. for those kits SoCZigbits Can be directly interfaced. 1.Xmega A3BU Xplained 2.Xmega B1 Xplained 3.Xmega A1 Xplained 4.SAM4S-XPLD 5.Mega1284P Xplained 6.STK600(mapping) 20-Pin/ZiGBITS Side SSEL MOSI MISO SCK 7 B 20-Pin/ Zigbits Extender Side P101-2*10RGF-139-ND GND COJ3 J3 1 2 ID_DATA PIJ301 PIJ302 3 4 ADC+/NC/DIG1 ADC-/DIG2 PIJ303 PIJ304 5 6 GPIO/CSDPIJ305 GPIO/CLKM PIJ306 7 8 PWM+/RST# PWM-/FEM_SEL/CPS PIJ307 PIJ308 9 10 IRQ SPI_SS_B/GPIO/SLP_TR PIJ309 PIJ3010 11 12 TWI_SDA PIJ3011 TWI_SCL PIJ3012 13 14 UART_RXPIJ3013 UART_TX PIJ3014 15 16 SPI_SS/SEL SPI_MOSI PIJ3015 PIJ3016 17 18 SPI_MISOPIJ3017 SPI_SCK VCC_P3V3 PIJ3018 19 20 Connections Block PIJ3019 PIJ3020 HEADER 2x10 GND Note: Place 100nF very near to Connector PIC101 PIC102 PIC301 PIC302 C1 COC1 COC3 C3 100n 4.7uF C Right Angle C GND 10-Pin/EVK Side J1 COJ1 1 RST# PIJ101 IRQ/RXD 3 PIJ103 5 SSEL PIJ105 7 MISO PIJ107 9 PIJ109 2 4 PIJ104 6 PIJ106 8 PIJ108 10 PIJ102 PIJ1010 MISC SLP_TR/TXD MOSI SCK VCC_3V3_IN 1. RF212B RF-only Zigbits 2. RF233 RF-only Zigbits 3. mega256RFR2 SoC Zigbits(Optional - only listed kits will be supported) 2 1 PIR302 J5 COJ5 HEADER 1x2 HMTSW-102-23-F-S-237 R3 330R COR3 D1 2 PIR301 PID102 COD1 1 PID101 EL17-21UYC/A2 Yellow GND D VCC_P3V3 PIJ502 PIJ501 Pin in paste possible SSW-105-02-G-D-RA Note: As this is an adapto doesn't require Rubber Feet Supported Zigbits JS3 COJS3 To be used by request from ESCATEC SNT-100-BK-G ATMEL R&D INDIA Mallikarjun RMZ Millenia Narayana Karthik Chennai * D INDIA GND Date: 7/16/2013 1:59:52 PM Document number: * PAGE: 1 of Revision: 1 TITLE: 10-pin to 20-pin XPRO adaptor ATXPRO-10PIN.SchDoc 1 2 3 4 5 6 7 8 1 3. Revision History Doc. Rev. Date 42207A 10/2013 Comments Initial document release 10Pin XPRO Adapter [USER GUIDE] 42207A−WIRELESS−10/2013 6 Atmel Corporation Atmel Asia Limited Atmel Munich GmbH Atmel Japan G.K. 1600 Technology Drive Unit 01-5 & 16, 19F Business Campus 16F Shin-Osaki Kangyo Bldg. San Jose, CA 95110 BEA Tower, Millennium City 5 Parkring 4 1-6-4 Osaki, Shinagawa-ku USA 418 Kwun Tong Road D-85748 Garching b. Munich Tokyo 141-0032 Tel: (+1)(408) 441-0311 Kwun Tong, Kowloon GERMANY JAPAN Fax: (+1)(408) 487-2600 HONG KONG Tel: (+49) 89-31970-0 Tel: (+81)(3) 6417-0300 www.atmel.com Tel: (+852) 2245-6100 Fax: (+49) 89-3194621 Fax: (+81)(3) 6417-0370 Fax: (+852) 2722-1369 © 2013 Atmel Corporation. All rights reserved. / Rev.: 42207A−WIRELESS−10/2013 Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, STK®, XMEGA®, ZigBit® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.