COM20020i Rev. D
5Mbps ARCNET (ANSI 878.1) Controller with 2K x 8 On-chip RAM
Highlights
• Data Rates up to 5 Mbps
• Programmable Reconfiguration Times
• 28-Pin PLCC and 48-Pin TQFP RoHS Compliant
packages
• Ideal for Industrial/Factory/Building Automation
and Transportation Applications
• Deterministic, (ANSI 878.1), Token Passing ARCNET Protocol
• Minimal Microcontroller and Media Interface Logic
Required
• Flexible Interface For Use With All Microcontrollers or Microprocessors
• Automatically Detects Type of Microcontroller
Interface
• 2Kx8 On-chip Dual Port RAM
• Command Chaining for Packet Queuing
• Sequential Access to Internal RAM
• Software Programmable Node ID
2001-2020 Microchip Technology Inc.
• Eight, 256 Byte Pages Allow Four Pages TX and
RX Plus Scratch-Pad Memory
• Next ID Readable
• Internal Clock Scaler and Clock Multiplier for
Adjusting Network Speed
• Operating Temperature Range of -40oC to +85oC
• Self-Reconfiguration Protocol
• Supports up to 255 Nodes
• Supports Various Network Topologies (Star, Tree,
Bus...)
• CMOS, Single +5V Supply
• Duplicate Node ID Detection
• Powerful Diagnostics
• Receive All Packets Mode
• Flexible Media Interface:
- Traditional Hybrid Interface For Long Distances up to Four Miles at 2.5 Mbps
- RS485 Differential Driver Interface For Low
Cost, Low Power, High Reliability
DS00002704C-page 1
COM20020i Rev. D
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com. We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the
revision of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
• Microchip’s Worldwide Web site; http://www.microchip.com
• Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include -literature number) you are
using.
Customer Notification System
Register on our web site at www.microchip.com to receive the most current information on all of our products.
DS00002704C-page 2
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
Table of Contents
1.0 General Description ........................................................................................................................................................................ 4
2.0 Pin Configuration ............................................................................................................................................................................ 5
3.0 Description of Pin Functions ........................................................................................................................................................... 7
4.0 Protocol Description ...................................................................................................................................................................... 10
5.0 System Description ....................................................................................................................................................................... 14
6.0 Functional Description .................................................................................................................................................................. 21
7.0 Operational Description ................................................................................................................................................................ 41
8.0 Timing Diagrams ........................................................................................................................................................................... 44
9.0 Package Outline ............................................................................................................................................................................ 57
Appendix A: Function of NOSYNC and EF Bits .................................................................................................................................. 59
Appendix B: Example of Interface Circuit Diagram to ISA Bus ........................................................................................................... 62
Appendix C: Software Identification of the COM20020 Rev B, Rev C and Rev D .............................................................................. 63
Appendix D: Data Sheet Revision History .......................................................................................................................................... 64
The Microchip Web Site ...................................................................................................................................................................... 65
Customer Change Notification Service ............................................................................................................................................... 65
Customer Support ............................................................................................................................................................................... 65
Product Identification System ............................................................................................................................................................. 66
2001-2020 Microchip Technology Inc.
DS00002704C-page 3
COM20020i Rev. D
1.0
GENERAL DESCRIPTION
Microchip's COM20020iD is a member of the family of Embedded ARCNET Controllers. The device is a general purpose communications controller for networking microcontrollers and intelligent peripherals in industrial, automotive, and
embedded control environments using an ARCNET® protocol engine. The small 28 pin package, flexible microcontroller
and media interfaces, eight- page message support, and extended temperature range of the COM20020iD make it the
only true network controller optimized for use in industrial, embedded, and automotive applications. Using an ARCNET
protocol engine is the ideal solution for embedded control applications because it provides a deterministic token-passing
protocol, a highly reliable and proven networking scheme, and a data rate of up to 5 Mbps when using the COM20020iD.
A token-passing protocol provides predictable response times because each network event occurs within a predetermined time interval, based upon the number of nodes on the network. The deterministic nature of ARCNET is essential
in real time applications. The integration of the 2Kx8 RAM buffer on-chip, the Command Chaining feature, the 5 Mbps
maximum data rate, and the internal diagnostics make the COM20020iD the highest performance embedded communications device available. With only one COM20020iD and one microcontroller, a complete communications node may
be implemented.
For more details on the ARCNET protocol engine and traditional dipulse signaling schemes, please refer to the ARCNET Local
Area Network Standard, available from Microchip or the ARCNET Designer's Handbook, available from Datapoint Corporation.
For more detailed information on cabling options including RS485, transformer-coupled RS-485 and Fiber Optic interfaces,
please refer to the following technical note which is available from Microchip: Technical Note 7-5 - Cabling Guidelines for the
COM20020iD ULANC.
DS00002704C-page 4
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
2.0
PIN CONFIGURATION
FIGURE 2-1:
COM20020ID 28-PIN PLCC PACKAGE
nWR/DIR
26
nRD/nDS
27
VDD
nCS
nINTR
nRESET IN
VSS
nTXEN
RXIN
nPULSE2
25
24
23
22
21
20
19
COM20020i
28
28-Pin PLCC
18
nPULSE 1
17
XTAL2
16
XTAL1
VSS
A2/ALE
3
13
N/C
AD0
4
12
D7
2001-2020 Microchip Technology Inc.
5
6
7
8
9
10
11
D6
14
D5
2
D4
A1
D3
VDD
VSS
15
AD2
1
AD1
A0/nMUX
DS00002704C-page 5
COM20020i Rev. D
DS00002704C-page 6
N/C
N/C
A2/ALE
A1
A0/nMUX
VDD
N/C
VSS
N/C
nRD/nDS
VDD
nWR/DIR
48
47
46
45
44
43
42
41
40
39
38
37
COM20020ID 48-PIN TQFP
AD0
1
36
nCS
AD1
2
35
VDD
N/C
3
34
nINTR
AD2
4
33
N/C
N/C
5
32
VDD
VSS
6
31
nRESET
D3
7
30
VSS
VDD
8
29
nTXEN
D4
9
28
RXIN
D5
10
27
N/C
VSS
11
26
BUSTMG
D6
12
25
nPULSE2
21
22
23
24
XTAL2
VSS
nPULSE1
18
VSS
XTAL1
17
N/C
20
16
N/C
19
15
N/C
N/C
14
VDD
13
D7
COM20020i
48‐Pin TQFP
N/C
FIGURE 2-2:
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
3.0
DESCRIPTION OF PIN FUNCTIONS
PLCC Pin
Number
Name
Symbol
Description
MICROCONTROLLER INTERFACE
1-3
Address
0-2
A0/nMUX,
A1,A2/ALE
Input. On a non-multiplexed mode, A0-A2 are address input
bits. (A0 is the LSB) On a multiplexed address/data bus,
nMUX tied Low, A1 is left open, and ALE is tied to the
Address Latch Enable signal. A1 is connected to an internal
pull-up resistor.
4-6,8-12
Data 0-7
AD0-AD2, D3-D7
Input/Output. On a non-multiplexed bus, these signals are
used as the data lines for the device. On a multiplexed
address/data bus, AD0-AD2 act as the address lines
(latched by ALE) and as the low data lines for the device.
D3-D7 are always used for data only. These signals are connected to internal pull-up resistors.
27
nRead/nData
Strobe
nRD/nDS
Input. On a 68XX-like bus, nDS is an active low signal
issued by the microcontroller as the data strobe signal to
strobe the data onto the bus. On a 80XX-like bus, nRD is an
active low signal issued by the microcontroller to indicate a
read operation.
26
nWrite/
Direction
nWR/DIR
Input. On a 68XX-like bus, DIR is issued by the microcontroller as the Read/nWrite signal to determine the direction
of data transfer. In this case, a logic "1" selects a read operation, while a logic "0" selects a write operation. In this case,
data is actually strobed by the nDS signal. On an 80XX-like
bus, nWR is an active low signal issued by the microcontroller to indicate a write operation. In this case, a logic "0" on
this pin, when the COM20020iD is accessed, enables data
from the data bus to be written to the device.
23
nReset in
nRESET
Input. This active low signal executes a hardware reset.
24
nInterrupt
nINTR
Output. This active low signal is generated by the
COM20020iD when an enabled interrupt condition occurs.
25
nChip Select
nCS
Input. This active low signal selects the COM20020iD for an
access.
TRANSMISSION MEDIA INTERFACE
19,18
nPulse 2,
nPulse 1
nPULSE2,
nPULSE1
Output (nPULSE1), Input/Output (nPULSE2). In Normal
Mode, these active low signals carry the transmit data information, encoded in pulse format, as DIPULSE waveform.
When the device is in Backplane Mode, the nPULSE1 signal
driver is programmable (push/pull or open-drain), while the
nPULSE2 signal provides a clock with frequency of double
the data rate. nPULSE1 is connected to a weak internal pullup resistor on the open/drain driver in backplane mode.
20
Receive In
RXIN
Input. This signal carries the receive data information from
the line transceiver.
21
nTransmit
nEnable
nTXEN
Output. This signal is used prior to the Power-up to enable
the line drivers for transmission. The polarity of the signal is
programmable through the nPULSE2 pin.
nPULSE2 floating before Power-up: nTXEN active low
(Default option)
nPULSE2 grounded before Power-up: nTXEN active high
(This option is only available in Backplane Mode.)
2001-2020 Microchip Technology Inc.
DS00002704C-page 7
COM20020i Rev. D
PLCC Pin
Number
Name
Symbol
Description
16,17
Crystal
Oscillator
XTAL1,
XTAL2
An external crystal should be connected to these pins. Oscillation frequency range is from 10 to 20 MHz. If an external
TTL clock is used instead, it must be connected to XTAL1
with a 390 pull-up resistor, and XTAL2 should be left floating.
15,28
Power
Supply
VDD
+5 Volt Power Supply pin.
7,14,22
Ground
VSS
Ground pin.
DS00002704C-page 8
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 3-1:
COM20020ID OPERATION
Power On
Reconfigure
Timer has
Timed Out
Send
Reconfigure
Burst
Read Node ID
Write ID to
RAM Buffer
1
Set NID=ID
Y
Start
Reconfiguration
Timer (420 mS)*
N
Y
TA?
Y
Transmit
NAK
Y
RI?
Send
Packet
Y
ACK?
Y
Y
N
No
Activity
for 37.4
us?
N
NAK?
Y
Y
DID
=0?
Y
Y
N
Broadcast
Enabled?
DID
=ID?
N
Y
Set TA
Set TA
Increment
NID
Y
Set TMA
No
Activity
for 37.4
us?
N
Set NID=ID
Start Timer:
T=(255-ID)
x 73 us
Y
Write Buffer
with Packet
N
N
No Activity
for 41
uS?
Activity
On Line?
Pass the
Token
N
ACK?
N
RI?
1
N
No
Activity Y
for 37.4
us?
N
SOH?
Write SID
to Buffer
N
Y
N
Y
N
Transmit
Free Buffer
Enquiry
N
Was Packet
Broadcast?
N
Free Buffer
Enquiry to
this ID?
Transmit
ACK
Broadcast?
Y
N
Invitation
to Transmit to
this ID?
Y
N
N
N
CRC
OK?
Y
T=0?
Y
LENGTH N
OK?
Y
- ID refers to the identification number of the ID assigned to this node.
- NID refers to the next identification number that receives the token
after this ID passes it.
- SID refers to the source identification.
- DID refers to the destination identification.
- SOH refers to the start of header character; preceeds all data packets.
* Reconfig timer is programmable via setup2 register bits 1, 0.
DID
=0?
Y
Set RI
N
DID
=ID?
N
Y
SEND ACK
Note - All time values are valid for 5 Mbps.
2001-2020 Microchip Technology Inc.
DS00002704C-page 9
COM20020i Rev. D
4.0
PROTOCOL DESCRIPTION
4.1
Network Protocol
Communication on the network is based on a token passing protocol. Establishment of the network configuration and
management of the network protocol are handled entirely by the COM20020iD's internal microcoded sequencer. A processor or intelligent peripheral transmits data by simply loading a data packet and its destination ID into the
COM20020iD's internal RAM buffer, and issuing a command to enable the transmitter. When the COM20020iD next
receives the token, it verifies that the receiving node is ready by first transmitting a FREE BUFFER ENQUIRY message.
If the receiving node transmits an ACKnowledge message, the data packet is transmitted followed by a 16-bit CRC. If
the receiving node cannot accept the packet (typically its receiver is inhibited), it transmits a Negative AcKnowledge
message and the transmitter passes the token. Once it has been established that the receiving node can accept the
packet and transmission is complete, the receiving node verifies the packet. If the packet is received successfully, the
receiving node transmits an ACKnowledge message (or nothing if it is not received successfully) allowing the transmitter to set
the appropriate status bits to indicate successful or unsuccessful delivery of the packet. An interrupt mask permits the COM20020iD to
generate an interrupt to the processor when selected status bits become true. Figure 3-1 is a flow chart illustrating the internal operation of the COM20020iD connected to a 20 MHz crystal oscillator.
4.2
Data Rates
The COM20020iD is capable of supporting data rates from 156.25 Kbps to 5 Mbps. The following protocol description
assumes a 5 Mbps data rate. To attain the faster data rates, the clock frequency may be doubled by the internal clock
multiplier (see next section). For slower data rates, an internal clock divider scales down the clock frequency. Thus all
timeout values are scaled as shown in the following table:
Example:
IDLE LINE Timeout @ 5 Mbps = 41 s. IDLE LINE Timeout for 156.2 Kbps is 41 s * 32 = 1.3 ms
Internal Clock
Frequency
Clock Prescaler
40 MHz
20 MHz
4.2.1
Data Rate
Timeout Scaling Factor
(Multiply By)
Div. by 8
5 Mbps
1
Div. by 8
Div. by 16
Div. by 32
Div. by 64
Div. by 128
2.5 Mbps
1.25 Mbps
625 Kbps
312.5 Kbps
156.25 Kbps
2
4
8
16
32
SELECTING CLOCK FREQUENCIES ABOVE 2.5 MBPS
To realize a 5 Mbps network, an external 40 MHz clock must be input. However, since 40 MHz is near the frequency of
FM radio band, it is not practical for use for noise emission reasons.
Therefore, higher frequency clocks are generated from the 20 MHz crystal as selected through two bits in the Setup2
register, CKUP[1,0] as shown below. The selected clock is supplied to the ARCNET controller.
CKUP1
CKUP0
Clock Frequency Factor (Data Rate)
0
0
20 MHz (Up to 2.5Mbps) Default (Bypass)
0
1
40 MHz (Up to 5Mbps)
1
0
Reserved
1
1
Reserved
This clock multiplier is powered-down (bypassed) on default. After changing the CKUP1 and CKUP0 bits, the ARCNET
core operation is stopped and the internal PLL in the clock generator is awakened and it starts to generate the 40 MHz.
The lock out time of the internal PLL is 8uSec typically. After more than 8 msec (this wait time is defined as 1 msec in
this data sheet), it is necessary to write command data '18H' to the command register to re-start the ARCNET core operation. This clock generator is called “clock multiplier”.
Changing the CKUP1 and CKUP0 bits must be one time or less after releasing hardware reset.
The EF bit in the SETUP2 register must be set when the data rate is over 5 Mbps.
DS00002704C-page 10
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
4.3
Network Reconfiguration
A significant advantage of the COM20020iD is its ability to adapt to changes on the network. Whenever a new node is
activated or deactivated, a NETWORK RECONFIGURATION is performed. When a new COM20020iD is turned on
(creating a new active node on the network), or if the COM20020iD has not received an INVITATION TO TRANSMIT
for 420mS, or if a software reset occurs, the COM20020iD causes a NETWORK RECONFIGURATION by sending a
RECONFIGURE BURST consisting of eight marks and one space repeated 765 times. The purpose of this burst is to
terminate all activity on the network. Since this burst is longer than any other type of transmission, the burst will interfere
with the next INVITATION TO TRANSMIT, destroy the token and keep any other node from assuming control of the line.
When any COM20020iD senses an idle line for greater than 41S, which occurs only when the token Is lost, each
COM20020iD starts an internal timeout equal to 73s times the quantity 255 minus its own ID. The COM20020iD starts
network reconfiguration by sending an invitation to transmit first to itself and then to all other nodes by decrementing the
destination Node ID. If the timeout expires with no line activity, the COM20020iD starts sending INVITATION TO
TRANSMIT with the Destination ID (DID) equal to the currently stored NID. Within a given network, only one
COM20020iD will timeout (the one with the highest ID number). After sending the INVITATION TO TRANSMIT, the
COM20020iD waits for activity on the line. If there is no activity for 37.4S, the COM20020iD increments the NID value
and transmits another INVITATION TO TRANSMIT using the NID equal to the DID. If activity appears before the 37.4S
timeout expires, the COM20020iD releases control of the line. During NETWORK RECONFIGURATION, INVITATIONS
TO TRANSMIT are sent to all NIDs (1-255).
Each COM20020iD on the network will finally have saved a NID value equal to the ID of the COM20020iD that it
released control to. At this point, control is passed directly from one node to the next with no wasted INVITATIONS TO
TRANSMIT being sent to ID's not on the network, until the next NETWORK RECONFIGURATION occurs. When a node
is powered off, the previous node attempts to pass the token to it by issuing an INVITATION TO TRANSMIT. Since this
node does not respond, the previous node times out and transmits another INVITATION TO TRANSMIT to an incremented ID and eventually a response will be received.
The NETWORK RECONFIGURATION time depends on the number of nodes in the network, the propagation delay
between nodes, and the highest ID number on the network, but is typically within the range of 12 to 30.5 mS.
4.4
Broadcast Messages
Broadcasting gives a particular node the ability to transmit a data packet to all nodes on the network simultaneously. ID
zero is reserved for this feature and no node on the network can be assigned ID zero. To broadcast a message, the
transmitting node's processor simply loads the RAM buffer with the data packet and sets the DID equal to zero. FIGURE
5-3: on page 17 illustrates the position of each byte in the packet with the DID residing at address 0X01 or 1 Hex of the
current page selected in the "Enable Transmit from Page fnn" command. Each individual node has the ability to ignore
broadcast messages by setting the most significant bit of the "Enable Receive to Page fnn" command to a logic "0".
4.5
Extended Timeout Function
There are three timeouts associated with the COM20020iD operation. The values of these timeouts are controlled by
bits 3 and 4 of the Configuration Register and bit 5 of the Setup 1 Register.
4.5.1
RESPONSE TIME
The Response Time determines the maximum propagation delay allowed between any two nodes, and should be chosen to be larger than the round trip propagation delay between the two furthest nodes on the network plus the maximum
turn around time (the time it takes a particular COM20020iD to start sending a message in response to a received message) which is approximately 6.4 S. The round trip propagation delay is a function of the transmission media and network topology. For a typical system using RG62 coax in a baseband system, a one way cable propagation delay of 15.5
S translates to a distance of about 2 miles. The flow chart in Figure 3-1 uses a value of 37.4 S (15.5 + 15.5 + 6.4) to
determine if any node will respond.
2001-2020 Microchip Technology Inc.
DS00002704C-page 11
COM20020i Rev. D
4.5.2
IDLE TIME
The Idle Time is associated with a NETWORK RECONFIGURATION. FIGURE 3-1: on page 9 illustrates that during a
NETWORK RECONFIGURATION one node will continually transmit INVITATIONS TO TRANSMIT until it encounters
an active node. All other nodes on the network must distinguish between this operation and an entirely idle line. During
NETWORK RECONFIGURATION, activity will appear on the line every 41 S. This 41 S is equal to the Response
Time of 37.4 S plus the time it takes the COM20020iD to start retransmitting another message (usually another INVITATION TO TRANSMIT).
4.5.3
RECONFIGURATION TIME
If any node does not receive the token within the Reconfiguration Time, the node will initiate a NETWORK RECONFIGURATION. The ET2 and ET1 bits of the Configuration Register allow the network to operate over longer distances than
the 2 miles stated earlier. The logic levels on these bits control the maximum distances over which the COM20020iD
can operate by controlling the three timeout values described above. For proper network operation, all COM20020iD's
connected to the same network must have the same Response Time, Idle Time, and Reconfiguration Time.
4.6
Line Protocol
The ARCNET line protocol is considered isochronous because each byte is preceded by a start interval and ended with
a stop interval. Unlike asynchronous protocols, there is a constant amount of time separating each data byte. On a 5
Mbps network, each byte takes exactly 11 clock intervals of 200ns each. As a result, one byte is transmitted every 2.2
S and the time to transmit a message can be precisely determined. The line idles in a spacing (logic "0") condition. A
logic "0" is defined as no line activity and a logic "1" is defined as a negative pulse of 100nS duration. A transmission
starts with an ALERT BURST consisting of 6 unit intervals of mark (logic "1"). Eight bit data characters are then sent,
with each character preceded by 2 unit intervals of mark and one unit interval of space. Five types of transmission can
be performed as described below:
4.6.1
INVITATIONS TO TRANSMIT
An Invitation To Transmit is used to pass the token from one node to another and is sent by the following sequence:
• An ALERT BURST
• An EOT (End Of Transmission: ASCII code 04H)
• Two (repeated) DID (Destination ID) characters
ALERT
BURST
4.6.2
EOT
DID
DID
FREE BUFFER ENQUIRIES
A Free Buffer Enquiry is used to ask another node if it is able to accept a packet of data. It is sent by the following
sequence:
• An ALERT BURST
• An ENQ (ENQuiry: ASCII code 85H)
• Two (repeated) DID (Destination ID) characters
ALERT
BURST
4.6.3
ENQ
DID
DID
DATA PACKETS
A Data Packet consists of the actual data being sent to another node. It is sent by the following sequence:
•
•
•
•
•
An ALERT BURST
An SOH (Start Of Header--ASCII code 01H)
An SID (Source ID) character
Two (repeated) DID (Destination ID) characters
A single COUNT character which is the 2's complement of the number of data bytes to follow if a short packet is
sent, or 00H followed by a COUNT character if a long packet is sent.
DS00002704C-page 12
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
• N data bytes where COUNT = 256-N (or 512-N for a long packet)
• Two CRC (Cyclic Redundancy Check) characters. The CRC polynomial used is: X16 + X15 + X2 + 1.
ALERT
BURST
4.6.4
SOH
SID
DID
DID
COUNT
data
data
CRC
CRC
ACKNOWLEDGEMENTS
An Acknowledgement is used to acknowledge reception of a packet or as an affirmative response to FREE BUFFER
ENQUIRIES and is sent by the following sequence:
• An ALERT BURST
• An ACK (ACKnowledgement--ASCII code 86H) character
ALERT BURST
4.6.5
ACK
NEGATIVE ACKNOWLEDGEMENTS
A Negative Acknowledgement is used as a negative response to FREE BUFFER ENQUIRIES and is sent by the following sequence:
• An ALERT BURST
• A NAK (Negative Acknowledgement--ASCII code 15H) character
ALERT BURST
2001-2020 Microchip Technology Inc.
NAK
DS00002704C-page 13
COM20020i Rev. D
5.0
SYSTEM DESCRIPTION
5.1
Microcontroller Interface
The top halves of Figure 5-1 and Figure 5-2 illustrate typical COM20020iD interfaces to the microcontrollers. The interfaces consist of a 8-bit data bus, an address bus and a control bus. In order to support a wide range of microcontrollers
without requiring glue logic and without increasing the number of pins, the COM20020iD automatically detects and
adapts to the type of microcontroller being used. Upon hardware reset, the COM20020iD first determines whether the
read and write control signals are separate READ and WRITE signals (like the 80XX) or DIRECTION and DATA
STROBE (like the 68XX). To determine the type of control signals, the device requires the software to execute at least
one write access to external memory before attempting to access the COM20020iD. The device defaults to 80XX-like
signals. Once the type of control signals are determined, the COM20020iD remains in this interface mode until the next
hardware reset occurs. The second determination the COM20020iD makes is whether the bus is multiplexed or nonmultiplexed. To determine the type of bus, the device requires the software to write to an odd memory location followed
by a read from an odd location before attempting to access the COM20020iD. The signal on the A0 pin during the odd
location access tells the COM20020iD the type of bus. Since multiplexed operation requires A0 to be active low, activity
on the A0 line tells the COM20020iD that the bus is non-multiplexed. The device defaults to multiplexed operation. Both
determinations may be made simultaneously by performing a WRITE followed by a READ operation to an odd location
within the COM20020iD Address space 20020D registers. Once the type of bus is determined, the COM20020iD
remains in this interface mode until hardware reset occurs.
Whenever nCS and nRD are activated, the preset determinations are assumed as final and will not be changed until
hardware reset. Refer to Description of Pin Functions section for details on the related signals. All accesses to the internal RAM and the internal registers are controlled by the COM20020iD. The internal RAM is accessed via a pointerbased scheme (refer to the Sequential Access Memory section), and the internal registers are accessed via direct
addressing. Many peripherals are not fast enough to take advantage of high-speed microcontrollers. Since microcontrollers do not typically have READY inputs, standard peripherals cannot extend cycles to extend the access time. The
access time of the COM20020iD, on the other hand, is so fast that it does not need to limit the speed of the microcontroller. The COM20020iD is designed to be flexible so that it is independent of the microcontroller speed.
The COM20020iD provides for no wait state arbitration via direct addressing to its internal registers and a pointer based
addressing scheme to access its internal RAM. The pointer may be used in auto-increment mode for typical sequential
buffer emptying or loading, or it can be taken out of auto-increment mode to perform random accesses to the RAM. The
data within the RAM is accessed through the data register. Data being read is prefetched from memory and placed into
the data register for the microcontroller to read. It is important to notice that only by writing a new address pointer (writing
to an address pointer low), one obtains the contents of COM20020iD internal RAM. Performing only read from the Data
Register does not load new data from the internal RAM. During a write operation, the data is stored in the data register
and then written into memory. Whenever the pointer is loaded for reads with a new value, data is immediately prefetched
to prepare for the first read operation.
DS00002704C-page 14
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 5-1:
MULTIPLEXED, 8051-LIKE BUS INTERFACE WITH RS-485 INTERFACE
XTAL1
XTAL2
AD0-AD7
COM20022
AD0-AD2, D3-D7
ALE
A2/BALE
A15
nCS
RESET
RXIN
nRESET
nTXEN
75176B or
Equiv.
nPULSE1
nRD
nRD/nDS
nWR
nINT1
nWR/DIR
nINTR
nPULSE2
GND
Differential Driver
Configuration
8051
A0/nMUX XTAL1
27 pF
* Media Interface
may be replaced
with Figure A, B or C.
XTAL2
27 pF
20 MHz
XTAL
+5V
RXIN
+5V
2
6
RXIN
Receiver
HFD3212-002
7
100 Ohm
TXEN
Transmitter
3 HFE4211-014
nPULSE1
nPULSE1
nPULSE2
+5V
GND
2
6
7
2 Fiber Interface
(ST Connectors)
BACKPLANE CONFIGURATION
FIGURE A
2001-2020 Microchip Technology Inc.
NOTE: COM20022 must be in backplane mode
FIGURE B
DS00002704C-page 15
COM20020i Rev. D
FIGURE 5-2:
NON-MULTIPLEXED, 6801-LIKE BUS INTERFACE WITH RS-485 INTERFACE
XTAL1
COM20022
XTAL2
D0-D7
D0-D7
A0
A0/nMUX
A1
A1
A2
A2/BALE
A7
nCS
RXIN
nPULSE1
nRES
nRESET
nIOS
nRD/nDS
R/nW
nWR/nDIR
nIRQ1
75176B or
Equiv.
TXEN
nPULSE2
GND
nINTR
Differential Driver
Configuration
6801
XTAL1
27 pF
* Media Interface
may be replaced
with Figure A, B or C.
XTAL2
27 pF
20MHz
XTAL
+5V
HYC9068 or
HYC9088
10
uF
RXIN
RXIN
+
0.47
uF
6
12
nTXEN
N/C
11
nPULSE1
nPULSE1
nPULSE2
nPULSE2
GND
17, 19,
4, 13, 14
5.6K
1/2W
5.6K
1/2W
0.01 uF
1KV
3
0.47
uF
+ 10
uF
-5V
Traditional Hybrid
Configuration
*Valid for 2.5 Mbps only.
FIGURE C
5.1.1
HIGH SPEED CPU BUS TIMING SUPPORT
High speed CPU bus support was added to the COM20020iD. The reasoning behind this is as follows: With the Host
interface in Non-multiplexed Bus mode, I/O address and Chip Select signals must be stable before the read signal is
active and remain after the read signal is inactive. But the High Speed CPU bus timing doesn't adhere to these timings.
For example, a RISC type single chip microcontroller (like the HITACHI SH-1 series) changes I/O address at the same
time as the read signal. Therefore, several external logic ICs would be required to connect to this microcontroller.
In addition, the Diagnostic Status (DIAG) register is cleared automatically by reading itself. The internal DIAG register
read signal is generated by decoding the Address (A2-A0), Chip Select (nCS) and Read (nRD) signals. The decoder
will generate a noise spike at the above tight timing. The DIAG register is cleared by the spike signal without reading
itself. This is unexpected operation. Reading the internal RAM and Next Id Register have the same mechanism as reading the DIAG register.
DS00002704C-page 16
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
Therefore, the address decode and host interface mode blocks were modified to fit the above CPU interface to support
high speed CPU bus timing. In Intel CPU mode (nRD, nWR mode), 3 bit I/O address (A2-A0) and Chip Select (nCS) are
sampled internally by Flip-Flops on the falling edge of the internal delayed nRD signal. The internal real read signal is
the more delayed nRD signal. But the rising edge of nRD doesn't delay. By this modification, the internal real address
and Chip Select are stable while the internal real read signal is active. Refer to Figure 5-3 below.
FIGURE 5-3:
HIGH SPEED CPU BUS TIMING – INTEL CPU MODE
VALID
A2-A0, nCS
nRD
Delayed nRD
(nRD1)
Sampled A2-A0, nCS
VALID
More delayed nRD
(nRD2)
The I/O address and Chip Select signals, which are supplied to the data output logic, are not sampled. Also, the nRD
signal is not delayed, because the above sampling and delaying paths decrease the data access time of the read cycle.
The above sampling and delaying signals are supplied to the Read Pulse Generation logic which generates the clearing
pulse for the Diagnostic register and generates the starting pulse of the RAM Arbitration. Typical delay time between
nRD and nRD1 is around 15nS and between nRD1 and nRD2 is around 10nS.
Longer pulse widths are needed due to these delays on nRD signal. However, the CPU can insert some wait cycles to
extend the width without any impact on performance.
The RBUSTMG bit was added to Disable/Enable the High Speed CPU Read function. It is defined as: RBUSTMG=0,
Disabled (Default); RBUSTMG=1, Enabled.
In the MOTOROLA CPU mode (DIR, nDS mode), the same modifications apply.
RBUSTMG Bit
5.2
Bus Timing Mode
0
Normal Speed CPU Read and Write
1
High Speed CPU Read and Normal Speed CPU Write
Transmission Media Interface
The bottom halves of Figure 5-1 and Figure 5-2 illustrate the COM20020iD interface to the transmission media used to
connect the node to the network. Table 5-1, “Typical Media,” on page 20 lists different types of cable which are suitable
for ARCNET applications. The user may interface to the cable of choice in one of three ways.
5.2.1
TRADITIONAL HYBRID INTERFACE
The Traditional Hybrid Interface is that which is used with previous ARCNET devices. The Hybrid Interface is recommended if the node is to be placed in a network with other Hybrid-Interfaced nodes. The Traditional Hybrid Interface is
for use with nodes operating at 2.5 Mbps only. The transformer coupling of the Hybrid offers isolation for the safety of
the system and offers high Common Mode Rejection. The Traditional Hybrid Interface uses circuits like Microchip's
HYC9068 or HYC9088 to transfer the pulse-encoded data between the cable and the COM20020iD. The COM20020iD
transmits a logic "1" by generating two 100nSnon-overlapping negative pulses, nPULSE1 and nPULSE2. Lack of pulses
indicates a logic "0". The nPULSE1 and nPULSE2 signals are sent to the Hybrid, which creates a 200nS dipulse signal
on the media. A logic "0" is transmitted by the absence of the dipulse. During reception, the 200nS dipulse appearing
2001-2020 Microchip Technology Inc.
DS00002704C-page 17
COM20020i Rev. D
on the media is coupled through the RF transformer of the LAN Driver, which produces a positive pulse at the RXIN pin
of the COM20020iD. The pulse on the RXIN pin represents a logic "1". Lack of pulse represents a logic "0". Typically,
RXIN pulses occur at multiples of 400nS. The COM20020iD can tolerate distortion of plus or minus 100nS and still correctly capture and convert the RXIN pulses to NRZ format.Figure 5-4 illustrates the events which occur in transmission
or reception of data consisting of 1, 1, 0.
Note:
5.2.2
Please refer to TN7-5 – Cabling Guidelines for the COM20020 ULANC, available from Microchip, for recommended cabling distance, termination, and node count for ARCNET nodes.
BACKPLANE CONFIGURATION
The Backplane Open Drain Configuration is recommended for cost-sensitive, short-distance applications like backplanes and instrumentation. This mode is advantageous because it saves components, cost, and power.
Since the Backplane Configuration encodes data differently than the traditional Hybrid Configuration, nodes utilizing the
Backplane Configuration cannot communicate directly with nodes utilizing the Traditional Hybrid Configuration. The
Backplane Configuration does not isolate the node from the media nor protects it from Common Mode noise, but Common Mode Noise is less of a problem in short distances.
The COM20020iD supplies a programmable output driver for Backplane Mode operation. A push/pull or open drain
driver can be selected by programming the P1MODE bit of the Setup 1 Register (see register descriptions for details).
The COM20020iD defaults to an open drain output.
The Backplane Configuration provides for direct connection between the COM20020iD and the media. Only one pullup resistor (in open drain configuration of the output driver) is required somewhere on the media (not on each individual
node). The nPULSE1 signal, in this mode, is an open drain or push/pull driver and is used to directly drive the media. It
issues a 200nS negative pulse to transmit a logic "1". Note that when used in the open-drain mode, the COM20020iD
does not have a fail/safe input on the RXIN pin. The nPULSE1 signal actually contains a weak pull-up resistor. This pullup should not take the place of the resistor required on the media for open drain mode.
FIGURE 5-4:
COM20020ID NETWORK USING RS-485 DIFFERENTIAL TRANSCEIVERS
RT
RT
+VCC
+VCC
RBIAS
RBIAS
75176B or
Equiv.
COM20020ID
DS00002704C-page 18
+VCC
COM20020ID
RBIAS
COM20020ID
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 5-5:
DIPULSE WAVEFORM FOR DATA OF 1-1-0
1
20MHZ
CLOCK
(FOR REF.
ONLY)
1
0
100ns
nPULSE1
100ns
nPULSE2
200ns
DIPULSE
400ns
RXIN
In typical applications, the serial backplane is terminated at both ends and a bias is provided by the external pull-up
resistor.
The RXIN signal is directly connected to the cable via an internal Schmitt trigger. A negative pulse on this input indicates
a logic "1". Lack of pulse indicates a logic "0". For typical single-ended backplane applications, RXIN is connected to
nPULSE1 to make the serial backplane data line. A ground line (from the coax or twisted pair) should run in parallel with
the signal. For applications requiring different treatment of the receive signal (like filtering or squelching), nPULSE1 and
RXIN remain as independent pins. External differential drivers/receivers for increased range and common mode noise
rejection, for example, would require the signals to be independent of one another. When the device is in Backplane
Mode, the clock provided by the nPULSE2 signal may be used for encoding the data into a different encoding scheme
or other synchronous operations needed on the serial data stream.
5.2.3
DIFFERENTIAL DRIVER CONFIGURATION
The Differential Driver Configuration is a special case of the Backplane Mode. It is a dc coupled configuration recommended for applications like car-area networks or other cost-sensitive applications which do not require direct compatibility with existing ARCNET nodes and do not require isolation.
The Differential Driver Configuration cannot communicate directly with nodes utilizing the Traditional Hybrid Configuration. Like the Backplane Configuration, the Differential Driver Configuration does not isolate the node from the media.
The Differential Driver interface includes a RS485 Driver/Receiver to transfer the data between the cable and the
COM20020iD. The nPULSE1 signal transmits the data, provided the Transmit Enable signal is active. The nPULSE1
signal issues a 200nS (at 2.5Mbps) negative pulse to transmit a logic "1". Lack of pulse indicates a logic "0". The RXIN
signal receives the data, the transmitter portion of the COM20020iD is disabled during reset and the nPULSE1,
nPULSE2 and nTXEN pins are inactive.
5.2.4
PROGRAMMABLE TXEN POLARITY
To accommodate transceivers with active high ENABLE pins, the COM20020iD contains a programmable TXEN output.
To program the TXEN pin for an active high pulse, the nPULSE2 pin should be connected to ground. To retain the normal
active low polarity, nPULSE2 should be left open. The polarity determination is made at power on reset and is valid only
for Backplane Mode operation. The nPULSE2 pin should remain grounded at all times if an active high polarity is
desired.
2001-2020 Microchip Technology Inc.
DS00002704C-page 19
COM20020i Rev. D
FIGURE 5-6:
INTERNAL BLOCK DIAGRAM
A0/nMUX
A1
A2/BALE
ADDRESS
DECODING
CIRCUITRY
2K x 8
RAM
ADDITIONAL
REGISTERS
AD0-AD2,
D3-D7
STATUS/
COMMAND
REGISTER
nINTR
RESET
LOGIC
nRESET
TX/RX
LOGIC
MICROSEQUENCER
AND
WORKING
REGISTERS
OSCILLATOR
nPULSE1
nPULSE2
nTXEN
RXIN
XTAL1
XTAL2
nRD/nDS
nWR/DIR
nCS
TABLE 5-1:
BUS
ARBITRATION
CIRCUITRY
RECONFIGURATION
TIMER
NODE ID
LOGIC
TYPICAL MEDIA
Cable Type
Nominal Impedance
Attenuation per 1000 Ft. at 5 MHz
RG-62 Belden #86262
93
5.5dB
RG-59/U Belden #89108
75
7.0dB
RG-11/U Belden #89108
75
5.5dB
IBM Type 1 (Note 5-1) Belden
#89688
150
7.0dB
IBM Type 3 (Note 5-1) Telephone
Twisted Pair Belden #1155A
100
17.9dB
COMCODE 26 AWG Twisted Pair
Part #105-064-703
105
16.0dB
Note 5-1
Note:
Non-plenum-rated cables of this type are also available.
For more detailed information on Cabling options including RS-485, transformer-coupled RS-485 and Fiber
Optic interfaces, please refer to TN7-5 – Cabling Guidelines for the COM20020 ULANC, available from
Microchip.
DS00002704C-page 20
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
6.0
FUNCTIONAL DESCRIPTION
6.1
Microsequencer
The COM20020iD contains an internal microsequencer which performs all of the control operations necessary to carry
out the ARCNET protocol. It consists of a clock generator, a 544 x 8 ROM, a program counter, two instruction registers,
an instruction decoder, a no-op generator, jump logic, and reconfiguration logic.
The COM20020iD derives a 10 MHz and a 5 MHz clock from the output clock of the Clock Multiplier. These clocks provide the rate at which the instructions are executed within the COM20020iD. The 10 MHz clock is the rate at which the
program counter operates, while the 5 MHz clock is the rate at which the instructions are executed. The microprogram
is stored in the ROM and the instructions are fetched and then placed into the instruction registers. One register holds
the opcode, while the other holds the immediate data. Once the instruction is fetched, it is decoded by the internal
instruction decoder, at which point the COM20020iD proceeds to execute the instruction. When a no-op instruction is
encountered, the microsequencer enters a timed loop and the program counter is temporarily stopped until the loop is
complete. When a jump instruction is encountered, the program counter is loaded with the jump address from the ROM.
The COM20020iD contains an internal reconfiguration timer which interrupts the microsequencer if it has timed out. At
this point the program counter is cleared and the MYRECON bit of the Diagnostic Status Register is set.
TABLE 6-1:
READ REGISTER SUMMARY
Register
MSB
LSB
ADDR
STATUS
RI/TRI
X/RI
X/TA
POR
TEST
RECON
TMA
TA/
TTA
00
DIAG.
STATUS
MYRECON
DUPID
RCVACT
TOKEN
EXCNAK
TENTID
NEW
NEXTID
X
01
ADDRESS
PTR HIGH
RD-DATA
AUTOINC
X
X
X
A10
A9
A8
02
ADDRESS
PTR LOW
A7
A6
A5
A4
A3
A2
A1
A0
03
DATA
D7
D6
D5
D4
D3
D2
D1
D0
04
SUB ADR
(R/W)
Note 6-1
0
0
0
SUBAD1
SUBAD0
05
CONFIGURATION
RESET
CCHEN
TXEN
ET1
ET2
BACKPLANE
SUBAD1
SUBAD0
06
TENTID
TID7
TID6
TID5
TID4
TID3
TID2
TID1
TID0
07-0
NODE ID
NID7
NID6
NID5
NID4
NID3
NID2
NID1
NID0
07-1
SETUP1
P1
MODE
FOUR
NAKS
X
RCVALL
CKP3
CKP2
CKP1
SLOWARB
07-2
NEXT ID
NXT ID7
NXT ID6
NXT ID5
NXT ID4
NXT ID3
NXT
ID2
NXT ID1
NXT ID0
07-3
SETUP2
RBUSTMG
X
CKUP1
CKUP0
EF
NOSYNC
RCNTM1
RCMTM2
07-4
Note 6-1
Read
(R/W)
SUB-AD2
Note 6-1
(R/W) This bit can be Written or Read. For more information see Appendix C: "Software Identification
of the COM20020 Rev B, Rev C and Rev D".
2001-2020 Microchip Technology Inc.
DS00002704C-page 21
COM20020i Rev. D
TABLE 6-2:
WRITE REGISTER SUMMARY
ADDR
MSB
Write
LSB
Register
00
RI/TR1
0
0
0
EXCNAK
RECON
NEW
NEXTID
TA/
TTA
INTERRUPT
MASK
01
C7
C6
C5
C4
C3
C2
C1
C0
COMMAND
02
RD-DATA
AUTOINC
0
0
0
A10
A9
A8
ADDRESS
PTR HIGH
03
A7
A6
A5
A4
A3
A2
A1
A0
ADDRESS
PTR LOW
04
D7
D6
D5
D4
D3
D2
D1
D0
DATA
05
(R/W)
Note 6-2
0
0
0
(R/W)
Note 6-2
SUB-AD2
SUBAD1
SUBAD0
SUBADR
06
RESET
CCHEN
TXEN
ET1
ET2
BACKPLANE
SUBAD1
SUBAD0
CONFIGURATION
07-0
TID7
TID6
TID5
TID4
TID3
TID2
TID1
TID0
TENTID
07-1
NID7
NID6
NID5
NID4
NID3
NID2
NID1
NID0
NODEID
07-2
P1MODE
FOUR
NAKS
0
RCVALL
CKP3
CKP2
CKP1
SLOWARB
SETUP1
07-3
0
0
0
0
0
0
0
0
TEST
07-4
RBUSTMG
0
CKUP1
CKUP0
EF
NOSYNC
RCNTM1
RCNTM0
SETUP2
Note 6-2
6.2
(R/W) This bit can be Written or Read. For more information see Appendix C: "Software Identification
of the COM20020 Rev B, Rev C and Rev D".
Internal Registers
The COM20020iD contains 14 internal registers. Table 6-1 and Table 6-2 illustrate the COM20020iD register map. All
undefined bits are read as undefined and must be written as logic "0".
6.2.1
INTERRUPT MASK REGISTER (IMR)
The COM20020iD is capable of generating an interrupt signal when certain status bits become true. A write to the IMR
specifies which status bits will be enabled to generate an interrupt. The bit positions in the IMR are in the same position
as their corresponding status bits in the Status Register and Diagnostic Status Register. A logic "1" in a particular position enables the corresponding interrupt. The Status bits capable of generating an interrupt include the Receiver Inhibited bit, New Next ID bit, Excessive NAK bit, Reconfiguration Timer bit, and Transmitter Available bit. No other Status or
Diagnostic Status bits can generate an interrupt.
The six maskable status bits are ANDed with their respective mask bits, and the results are ORed to produce the interrupt signal. An RI or TA interrupt is masked when the corresponding mask bit is reset to logic "0", but will reappear when
the corresponding mask bit is set to logic "1" again, unless the interrupt status condition has been cleared by this time.
A RECON interrupt is cleared when the "Clear Flags" command is issued. An EXCNAK interrupt is cleared when the
"POR Clear Flags" command is issued. A New Next ID interrupt is cleared by reading the Next ID Register. The Interrupt
Mask Register defaults to the value 0000 0000 upon hardware reset.
6.2.2
DATA REGISTER
This read/write 8-bit register is used as the channel through which the data to and from the RAM passes. The data is
placed in or retrieved from the address location presently specified by the address pointer. The contents of the Data
Register are undefined upon hardware reset. In case of READ operation, the Data Register is loaded with the contents
of COM20020iD Internal Memory upon writing Address Pointer low only once.
6.2.3
TENTATIVE ID REGISTER
The Tentative ID Register is a read/write 8-bit register accessed when the Sub Address Bits are set up accordingly
(please refer to the Configuration Register and SUB ADR Register). The Tentative ID Register can be used while the
node is on-line to build a network map of those nodes existing on the network. It minimizes the need for operator inter-
DS00002704C-page 22
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
action with the network. The node determines the existence of other nodes by placing a Node ID value in the Tentative
ID Register and waiting to see if the Tentative ID bit of the Diagnostic Status Register gets set. The network map developed by this method is only valid for a short period of time, since nodes may join or depart from the network at any time.
When using the Tentative ID feature, a node cannot detect the existence of the next logical node to which it passes the
token. The Next ID Register will hold the ID value of that node. The Tentative ID Register defaults to the value 0000 0000
upon hardware reset only.
6.2.4
NODE ID REGISTER
The Node ID Register is a read/write 8-bit register accessed when the Sub Address Bits are set up accordingly (please
refer to the Configuration Register and SUB ADR Register). The Node ID Register contains the unique value which identifies this particular node. Each node on the network must have a unique Node ID value at all times. The Duplicate ID
bit of the Diagnostic Status Register helps the user find a unique Node ID. Refer to the Initialization Sequence section
for further detail on the use of the DUPID bit. The core of the COM20020iD does not wake up until a Node ID other than
zero is written into the Node ID Register. During this time, no microcode is executed, no tokens are passed by this node,
and no reconfigurations are caused by this node. Once a non-zero NodeID is placed into the Node ID Register, the core
wakes up but will not join the network until the TXEN bit of the Configuration Register is set. While the Transmitter is
disabled, the Receiver portion of the device is still functional and will provide the user with useful information about the
network. The Node ID Register defaults to the value 0000 0000 upon hardware reset only.
6.2.5
NEXT ID REGISTER
The Next ID Register is an 8-bit, read-only register, accessed when the sub-address bits are set up accordingly (please
refer to the Configuration Register and SUB ADR Register). The Next ID Register holds the value of the Node ID to
which the COM20020iD will pass the token. When used in conjunction with the Tentative ID Register, the Next ID Register can provide a complete network map. The Next ID Register is updated each time a node enters/leaves the network
or when a network reconfiguration occurs. Each time the microsequencer updates the Next ID Register, a New Next ID
interrupt is generated. This bit is cleared by reading the Next ID Register. Default value is 0000 0000 upon hardware or
software reset.
6.2.6
STATUS REGISTER
The COM20020iD Status Register is an 8-bit read-only register. All of the bits, except for bits 5 and 6, are software compatible with previous Microchip ARCNET devices. In previous Microchip ARCNET devices the Extended Timeout status
was provided in bits 5 and 6 of the Status Register. In the COM20020iD, the COM20020, the COM90C66, and the
COM90C165, COM20020-5, COM20051 and COM20051+ these bits exist in and are controlled by the Configuration
Register. The Status Register contents are defined as in Table 6-3, but are defined differently during the Command
Chaining operation. Please refer to the Command Chaining section for the definition of the Status Register during Command Chaining operation. The Status Register defaults to the value 1XX1 0001 upon either hardware or software reset.
6.2.7
DIAGNOSTIC STATUS REGISTER
The Diagnostic Status Register contains seven read-only bits which help the user troubleshoot the network or node
operation. Various combinations of these bits and the TXEN bit of the Configuration Register represent different situations. All of these bits, except the Excessive NAcK bit and the New Next ID bit, are reset to logic "0" upon reading the
Diagnostic Status Register or upon software or hardware reset. The EXCNAK bit is reset by the "POR Clear Flags" command or upon software or hardware reset. The Diagnostic Status Register defaults to the value 0000 000X upon either
hardware or software reset.
6.2.8
COMMAND REGISTER
Execution of commands are initiated by performing microcontroller writes to this register. Any combinations of written
data other than those listed in Table 6-4 are not permitted and may result in incorrect chip and/or network operation.
6.2.9
ADDRESS POINTER REGISTERS
These read/write registers are each 8-bits wide and are used for addressing the internal RAM. New pointer addresses
should be written by first writing to the High Register and then writing to the Low Register because writing to the Low
Register loads the address. The contents of the Address Pointer High and Low Registers are undefined upon hardware
reset. Writing to Address Pointer low loads the address.
2001-2020 Microchip Technology Inc.
DS00002704C-page 23
COM20020i Rev. D
6.2.10
CONFIGURATION REGISTER
The Configuration Register is a read/write register which is used to configure the different modes of the COM20020iD.
The Configuration Register defaults to the value 0001 1000 upon hardware reset only. SUBAD0 and SUBAD1 point to
the selection in Register 7.
6.2.11
SUB-ADDRESS REGISTER
The sub-address register is new to the COM20020iD, previously a reserved register. Bits 2, 1 and 0 are used to select
one of the registers assigned to address 7h. SUBAD1 and SUBAD0 already exist in the Configuration register on the
COM20020B. They are exactly same as those in the Sub-Address register. If the SUBAD1 and SUBAD0 bits in the Configuration register are changed, the SUBAD1and SUBAD0 in the Sub-Address register are also changed. SUBAD2 is a
new sub-address bit. It Is used to access the 1 new Set Up register, SETUP2. This register is selected by setting SUBAD2=1. The SUBAD2 bit is cleared automatically by writing the Configuration register.
6.2.12
SETUP 1 REGISTER
The Setup 1 Register is a read/write 8-bit register accessed when the Sub Address Bits are set up accordingly (see the
bit definitions of the Configuration Register). The Setup 1 Register allows the user to change the network speed (data
rate) or the arbitration speed independently, invoke the Receive All feature and change the nPULSE1 driver type. The
data rate may be slowed to 156.25Kbps and/or the arbitration speed may be slowed by a factor of two. The Setup 1
Register defaults to the value 0000 0000 upon hardware reset only.
6.2.13
SETUP 2 REGISTER
The Setup 2 Register is new to the COM20020iD. It is an 8-bit read/write register accessed when the Sub Address Bits
SUBAD[2:0] are set up accordingly (see the bit definitions of the Sub Address Register). This register contains bits for
various functions. The CKUP1,0 bits select the clock to be generated from the 20 MHz crystal. The RBUSTMG bit is
used to Disable/Enable Fast Read function for High Speed CPU bus support. The EF bit is used to enable the new timing
for certain functions in the COM20020iD (if EF = 0, the timing is the same as in the COM20020 Rev. B). See Appendix
A. The NOSYNC bit is used to enable the NOSYNC function during initialization. If this bit is reset, the line has to be idle
for the RAM initialization sequence to be written. If set, the line does not have to be idle for the initialization sequence
to be written. See Appendix A:, "Function of NOSYNC and EF Bits," on page 59.
The RCNTM[1,0] bits are used to set the time-out period of the recon timer. Programming this timer for shorter time
periods has the benefit of shortened network reconfiguration periods. The time periods shown in the table on the following page are limited by a maximum number of nodes in the network. These time-out period values are for 5Mbps. For
other data rates, scale the time-out period time values accordingly; the maximum node count remains the same.
RCNTM1
RCNTM0
Time-Out Period
MAX Node Count
0
0
420 mS
Up to 255 nodes
0
1
105 mS
Up to 64 nodes
1
0
52.5 mS
Up to 32 nodes
1
1
26.25 mS*
Up to 16 nodes (Note 6-3)
Note 6-3
The node ID value 255 must exist in the network for the 26.25 mS time-out to be valid.
DS00002704C-page 24
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
TABLE 6-3:
Bit
7
6,5
STATUS REGISTER
Bit Name
Receiver
Inhibited
Symbol
RI
(Reserved)
Description
This bit, if high, indicates that the receiver is not enabled because either an
"Enable Receive to Page fnn" command was never issued, or a packet has
been deposited into the RAM buffer page fnn as specified by the last
"Enable Receive to Page fnn" command. No messages will be received
until this command is issued, and once the message has been received,
the RI bit is set, thereby inhibiting the receiver. The RI bit is cleared by issuing an "Enable Receive to Page fnn" command. This bit, when set, will
cause an interrupt if the corresponding bit of the Interrupt Mask Register
(IMR) is also set. When this bit is set and another station attempts to send a
packet to this station, this station will send a NAK.
These bits are undefined.
4
Power On Reset
POR
This bit, if high, indicates that the COM20020iD has been reset by either a
software reset, a hardware reset, or writing 00H to the Node ID Register.
The POR bit is cleared by the "Clear Flags" command.
3
Test
TEST
This bit is intended for test and diagnostic purposes. It is a logic "0" under
normal operating conditions.
2
Reconfiguration
RECON
This bit, if high, indicates that the Line Idle Timer has timed out because the
RXIN pin was idle for 41S. The RECON bit is cleared during a "Clear
Flags" command. This bit, when set, will cause an interrupt if the corresponding bit in the IMR is also set. The interrupt service routine should consist of examining the MYRECON bit of the Diagnostic Status Register to
determine whether there are consecutive reconfigurations caused by this
node.
1
Transmitter
Message
Acknowledged
TMA
This bit, if high, indicates that the packet transmitted as a result of an
"Enable Transmit from Page fnn" command has been acknowledged. This
bit should only be considered valid after the TA bit (bit 0) is set. Broadcast
messages are never acknowledged. The TMA bit is cleared by issuing the
"Enable Transmit from Page fnn" command.
0
Transmitter
Available
TA
This bit, if high, indicates that the transmitter is available for transmitting.
This bit is set when the last byte of scheduled packet has been transmitted
out, or upon execution of a "Disable Transmitter" command. The TA bit is
cleared by issuing the "Enable Transmit from Page fnn" command after the
node next receives the token. This bit, when set, will cause an interrupt if
the corresponding bit in the IMR is also set.
2001-2020 Microchip Technology Inc.
DS00002704C-page 25
COM20020i Rev. D
TABLE 6-4:
Bit
DIAGNOSTIC STATUS REGISTER
Bit Name
Symbol
Description
7
My Reconfiguration MYRECON
This bit, if high, indicates that a past reconfiguration was caused by this
node. It is set when the Lost Token Timer times out, and should be typically
read following an interrupt caused by RECON. Refer to the Improved Diagnostics section for further detail.
6
Duplicate ID
DUPID
This bit, if high, indicates that the value in the Node ID Register matches
both Destination ID characters of the token and a response to this token
has occurred. Trailing zero's are also verified. A logic "1" on this bit indicates a duplicate Node ID, thus the user should write a new value into the
Node ID Register. This bit is only useful for duplicate ID detection when the
device is off line, that is, when the transmitter is disabled. When the device
is on line this bit will be set every time the device gets the token. This bit is
reset automatically upon reading the Diagnostic Status Register. Refer to
the Improved Diagnostics section for further detail.
5
Receive
Activity
RCVACT
This bit, if high, indicates that data activity (logic "1") was detected on the
RXIN pin of the device. Refer to the Improved Diagnostics section for further detail.
4
Token Seen
TOKEN
This bit, if high, indicates that a token has been seen on the network, sent
by a node other than this one. Refer to the Improved Diagnostic section for
further detail.
3
Excessive NAK
EXCNAK
This bit, if high, indicates that either 128 or 4 Negative Acknowledgements
have occurred in response to the Free Buffer Enquiry. This bit is cleared
upon the "POR Clear Flags" command. Reading the Diagnostic Status
Register does not clear this bit. This bit, when set, will cause an interrupt if
the corresponding bit in the IMR is also set. Refer to the Improved Diagnostics section for further detail.
2
Tentative ID
TENTID
This bit, if high, indicates that a response to a token whose DID matches
the value in the Tentative ID Register has occurred. The second DID and
the trailing zero's are not checked. Since each node sees every token
passed around the network, this feature can be used with the device on-line
in order to build and update a network map. Refer to the Improved Diagnostics section for further detail.
1
New Next ID
NEW
NXTID
This bit, if high, indicates that the Next ID Register has been updated and
that a node has either joined or left the network. Reading the Diagnostic
Status Register does not clear this bit. This bit, when set, will cause an
interrupt if the corresponding bit in the IMR is also set. The bit is cleared by
reading the Next ID Register.
1,0
(Reserved)
DS00002704C-page 26
These bits are undefined.
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
TABLE 6-5:
Data
COMMAND REGISTER
Command
Description
0000 0000
Clear
Transmit
Interrupt
This command is used only in the Command Chaining operation. Please
refer to the Command Chaining section for definition of this command.
0000 0001
Disable
Transmitter
This command will cancel any pending transmit command (transmission
that has not yet started) and will set the TA (Transmitter Available) status
bit to logic "1" when the COM20020iD next receives the token.
0000 0010
Disable
Receiver
This command will cancel any pending receive command. If the
COM20020iD is not yet receiving a packet, the RI (Receiver Inhibited) bit
will be set to logic "1" the next time the token is received. If packet reception is already underway, reception will run to its normal conclusion.
b0fn n100
Enable
Receive to
Page fnn
This command allows the COM20020iD to receive data packets into RAM
buffer page fnn and resets the RI status bit to logic "0". The values placed
in the "nn" bits indicate the page that the data will be received into (page
0, 1, 2, or 3). If the value of "f" is a logic "1", an offset of 256 bytes will be
added to that page specified in "nn", allowing a finer resolution of the buffer. Refer to the Selecting RAM Page Size section for further detail. If the
value of "b" is logic "1", the device will also receive broadcasts (transmissions to ID zero). The RI status bit is set to logic "1" upon successful
reception of a message.
00fn n011
Enable
Transmit from
Page fnn
This command prepares the COM20020iD to begin a transmit sequence
from RAM buffer page fnn the next time it receives the token. The values
of the "nn" bits indicate which page to transmit from (0, 1, 2, or 3). If "f" is
logic "1", an offset of 256 bytes is the start of the page specified in "nn",
allowing a finer resolution of the buffer. Refer to the Selecting RAM Page
Size section for further detail. When this command is loaded, the TA and
TMA bits are reset to logic "0". The TA bit is set to logic "1" upon completion of the transmit sequence. The TMA bit will have been set by this time
if the device has received an ACK from the destination node. The ACK is
strictly hardware level, sent by the receiving node before its microcontroller is even aware of message reception. Refer to Figure 3-1 for details of
the transmit sequence and its relation to the TA and TMA status bits.
0000 c101
Define
Configuration
This command defines the maximum length of packets that may be handled by the device. If "c" is a logic "1", the device handles both long and
short packets. If "c" is a logic "0", the device handles only short packets.
000r p110
Clear Flags
This command resets certain status bits of the COM20020iD. A logic "1"
on "p" resets the POR status bit and the EXCNAK Diagnostic status bit. A
logic "1" on "r" resets the RECON status bit.
0000 1000
Clear
Receive
Interrupt
This command is used only in the Command Chaining operation. Please
refer to the Command Chaining section for definition of this command.
0001 1000
Start Internal Operation
This command restarts the stopped internal operation after changing
CKUP1 or CKUP0 bit.
2001-2020 Microchip Technology Inc.
DS00002704C-page 27
COM20020i Rev. D
TABLE 6-6:
Bit
ADDRESS POINTER HIGH REGISTER
Bit Name
Symbol
Description
7
Read Data
RDDATA
This bit tells the COM20020iD whether the following access will be
a read or write. A logic "1" prepares the device for a read, a logic
"0" prepares it for a write.
6
Auto Increment
AUTOINC
This bit controls whether the address pointer will increment automatically. A logic "1" on this bit allows automatic increment of the
pointer after each access, while a logic "0" disables this function.
Please refer to the Sequential Access Memory section for further
detail.
5-3
(Reserved)
2-0
Address 10-8
TABLE 6-7:
Bit
7-0
Bit
7-3
2,1,0
These bits hold the upper three address bits which provide
addresses to RAM.
ADDRESS POINTER LOW REGISTER
Bit Name
Address 7-0
TABLE 6-8:
These bits are undefined.
A10-A8
Symbol
Description
A7-A0
These bits hold the lower 8 address bits which provide the
addresses to RAM.
SUB ADDRESS REGISTER
Bit Name
Symbol
Reserved
Sub Address 2,1,0
Description
These bits are undefined.
SUBAD
2,1,0
These bits determine which register at address 07 may be accessed.
The combinations are as follows:
SUBAD2
0
0
0
0
1
1
1
1
SUBAD1
0
0
1
1
0
0
1
1
SUBAD0
0
1
0
1
0
1
0
1
Register
Tentative ID \ (Same
Node ID
\ as in
Setup 1
/ Config
Next ID
/ Register)
Setup 2
Reserved
Reserved
Reserved
SUBAD1 and SUBAD0 are exactly the same as exist in the Configuration Register. SUBAD2 is cleared automatically by writing the Configuration Register.
DS00002704C-page 28
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
TABLE 6-9:
Bit
CONFIGURATION REGISTER
Bit Name
Symbol
Description
7
Reset
RESET
A software reset of the COM20020iD is executed by writing a logic
"1" to this bit. A software reset does not reset the microcontroller
interface mode, nor does it affect the Configuration Register. The
only registers that the software reset affect are the Status Register,
the Next ID Register, and the Diagnostic Status Register. This bit
must be brought back to logic "0" to release the reset.
6
Command
Chaining Enable
CCHEN
This bit, if high, enables the Command Chaining operation of the
device. Please refer to the Command Chaining section for further
details. A low level on this bit ensures software compatibility with previous Microchip ARCNET devices.
5
Transmit Enable
TXEN
When low, this bit disables transmissions by keeping nPULSE1,
nPULSE2 if in non-Backplane Mode, and nTXEN pin inactive. When
high, it enables the above signals to be activated during transmissions. This bit defaults low upon reset. This bit is typically enabled
once the Node ID is determined, and never disabled during normal
operation. Please refer to the Improved Diagnostics section for
details on evaluating network activity.
Extended
Timeout 1,2
ET1, ET2
These bits allow the network to operate over longer distances than
the default maximum 2 miles by controlling the Response, Idle, and
Reconfiguration Times. All nodes should be configured with the same
timeout values for proper network operation. For the COM20020iD
with a 20 MHz crystal oscillator, the bit combinations follow:
4,3
ET2
0
0
1
1
Note:
2
1,0
Reconfig
Time
Response
Idle Time
ET1
(mS)
Time (S)
(S)
0
840
596.6
656
1
840
298.4
328
0
840
149.2
164
1
420
37.4
41
These values are for 5Mbps and RCNTMR[1,0]=00.
Reconfiguration time is changed by the RCNTMR1 and
RCNTMR0 bits.
Backplane
BACKPLANE
A logic "1" on this bit puts the device into Backplane Mode signaling
which is used for Open Drain and Differential Driver interfaces.
Sub Address 1,0
SUBAD 1,0
These bits determine which register at address 07 may be accessed.
The combinations are as follows:
SUBAD1
0
0
1
1
SUBAD0
0
1
0
1
Register
Tentative ID
Node ID
Setup 1
Next ID
See also the Sub Address Register.
2001-2020 Microchip Technology Inc.
DS00002704C-page 29
COM20020i Rev. D
TABLE 6-10:
Bit
SETUP 1 REGISTER
Bit Name
Symbol
Description
7
Pulse1 Mode
P1MODE
6
Four NACKS
FOUR NACKS This bit, when set, will cause the EXNACK bit in the Diagnostic Status Register to set after four NACKs to Free Buffer Enquiry are
detected by the COM20020iD. This bit, when reset, will set the
EXNACK bit after 128 NACKs to Free Buffer Enquiry. The default is
128.
5
Reserved
4
Receive All
RCVALL
This bit, when set, allows the COM20020iD to receive all valid data
packets on the network, regardless of their destination ID. This
mode can be used to implement a network monitor with the transmitter on- or off-line. Note that ACKs are only sent for packets
received with a destination ID equal to the COM20020iD's programmed node ID. This feature can be used to put the
COM20020iD in a 'listen-only' mode, where the transmitter is disabled and the COM20020iD is not passing tokens. Defaults low.
Clock Prescaler Bits
3,2,1
CKP3,2,1
These bits are used to determine the data rate of the
COM20020iD. The following table is for a 20 MHz crystal: (Clock
Multiplier is bypassed).
3,2,1
This bit determines the type of PULSE1 output driver used in Backplane Mode. When high, a push/pull output is used. When low, an
open drain output is used. The default is open drain.
Do not set.
CKP3
0
0
0
0
1
Note:
0
Slow Arbitration Select SLOWARB
This bit, when set, will divide the arbitration clock by 2. Memory
cycle times will increase when slow arbitration is selected.
Note:
DS00002704C-page 30
CKP2 CKP1 DIVISOR
SPEED
0
0
8
2.5Mbs
0
1
16
1.25Mbs
1
0
32
625Kbs
1
1
64
312.5Kbs
0
0
128
156.25Kbs
The lowest data rate achievable by the COM20020iD is
156.25Kbs. Defaults to 000 or 2.5Mbs. For Clock Multiplier output clock speed greater than 20 MHz, CKP3,
CKP2 and CKP1 must all be zero.
For clock multiplier output clock speeds greater than 40
MHz, SLOWARB must be set. Defaults to low.
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
TABLE 6-11:
Bit
7
6
5,4
SETUP 2 REGISTER
Bit Name
Read Bus Timing
Select
Symbol
RBUSTMG
This bit is used to Disable/Enable the High Speed CPU Read function for High Speed CPU bus support. RBUSTMG=0: Disable
(Default), RBUSTMG=1: Enable. It does not influence write operation. High speed CPU Read operation is only for non-multiplexed
bus.
CKUP1, 0
Higher frequency clocks are generated from the 20 MHz crystal
through the selection of these two bits as shown. This clock multiplier
is powered-down on default. After changing the CKUP1 and CKUP0
bits, the ARCNET core operation is stopped and the internal PLL in
the clock multiplier is awakened and it starts to generate the 40 MHz.
The lock out time of the internal PLL is 8mSec typically. After 1 mS it
is necessary to write command data '18H' to command register for
re-starting the ARCNET core operation. EF bit must be ‘1’ if the data
rate is over 5Mbps.
CAUTION: Changing the CKUP1 and CKUP0 bits must be one time
or less after releasing a hardware reset.
Reserved
Clock Multiplier
Description
This bit is undefined.
CKUP1
CKUP0
Clock Frequency (Data Rate)
0
0
20 MHz (Up to 2.5Mbps) Default
0
1
40 MHz (Up to 5Mbps)
1
0
Reserved
1
Note:
1
Reserved
After changing the CKUP1 or CKUP0 bits, it is necessary
to write a command data '18H' to the command register.
Because after changing the CKUP [1, 0] bits, the internal
operation is stopped temporarily. The writing of the command is to start the operation.
These initializing steps are shown below.
Hardware reset (Power ON)
Change CKUP[1, 0] bit
Wait 1mSec (wait until stable oscillation)
Write command '18H' (start internal operation)
Start initializing routine (Execute existing software)
3
Enhanced Functions
EF
This bit is used to enable the new enhanced functions in the
COM20020iD. EF = 0: Disable (Default), EF = 1: Enable. If EF = 0,
the timing and function is the same as in the COM20020, Revision
B. See Appendix A: “Function of NOSYNC and EF Bits”. EF bit
must be ‘1’ if the data rate is over 5Mbps.
EF bit should be ‘1’ for new design customers.
EF bit should be ‘0’ for replacement customers.
2
No Synchronous
NOSYNC
This bit is used to enable the SYNC command during initialization.
NOSYNC= 0, Enable (Default) The line must be idle for the RAM
initialization sequence to be written. NOSYNC= 1, Disable:) The line
does not have to be idle for the RAM initialization sequence to be
written. See Appendix A.
2001-2020 Microchip Technology Inc.
DS00002704C-page 31
COM20020i Rev. D
TABLE 6-11:
SETUP 2 REGISTER (CONTINUED)
Bit
Bit Name
Symbol
1,0
Reconfiguration Timer
1, 0
RCNTM1,0
Description
These bits are used to program the reconfiguration timer as a
function of maximum node count. These bits set the time out period
of the reconfiguration timer as shown below. The time out periods
shown are for 5 Mbps.
RCNTM1
RCNTM0
Time Out Period
Max Node Count
0
0
420 mS
Up to 255 nodes
0
1
105 mS
Up to 64 nodes
1
0
52.5 mS
Up to 32 nodes
1
Note:
FIGURE 6-1:
1
26.25 mS*
Up to 16 nodes
*The node ID value 255 must exist in the network for 26.25
mS timeout to be valid.
SEQUENTIAL ACCESS OPERATION
Data Register
I/O Address 04H
Memory
Data Bus
2K x 8
8
D0-D7
INTERNAL
RAM
Address Pointer Register
I/O Address 02H
I/O Address 03H
High
Low
Memory
Address Bus
11-Bit Counter
11
DS00002704C-page 32
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
6.3
Internal RAM
The integration of the 2K x 8 RAM in the COM20020iD represents significant real estate savings. The most obvious
benefit is the 48 pin package in which the device is now placed (a direct result of the integration of RAM). In addition,
the PC board is now free of the cumbersome external RAM, external latch, and multiplexed address/data bus and control functions which were necessary to interface to the RAM. The integration of RAM represents significant cost savings
because it isolates the system designer from the changing costs of external RAM and it minimizes reliability problems,
assembly time and costs, and layout complexity.
6.3.1
SEQUENTIAL ACCESS MEMORY
The internal RAM is accessed via a pointer-based scheme. Rather than interfering with system memory, the internal
RAM is indirectly accessed through the Address High and Low Pointer Registers. The data is channeled to and from
the microcontroller via the 8-bit data register. For example: a packet in the internal RAM buffer is read by the microcontroller by writing the corresponding address into the Address Pointer High and Low Registers (offsets 02H and 03H).
Note that the High Register should be written first, followed by the Low Register, because writing to the Low Register
loads the address. At this point the device accesses that location and places the corresponding data into the data register. The microcontroller then reads the data register (offset 04H) to obtain the data at the specified location. If the Auto
Increment bit is set to logic "1", the device will automatically increment the address and place the next byte of data into
the data register, again to be read by the microcontroller. This process is continued until the entire packet is read out of
RAM. Refer to Figure 6-1 for an illustration of the Sequential Access operation. When switching between reads and
writes, the pointer must first be written with the starting address. At least one cycle time should separate the pointer
being loaded and the first read (see timing parameters).
6.3.2
ACCESS SPEED
The COM20020iD is able to accommodate very fast access cycles to its registers and buffers. Arbitration to the buffer
does not slow down the cycle because the pointer based access method allows data to be prefetched from memory and
stored in a temporary register. Likewise, data to be written is stored in the temporary register and then written to memory.
For systems which do not require quick access time, the arbitration clock may be slowed down by setting bit 0 of the
Setup1 Register equal to logic "1". Since the Slow Arbitration feature divides the input clock by two, the duty cycle of
the input clock may be relaxed.
6.4
Software Interface
The microcontroller interfaces to the COM20020iD via software by accessing the various registers. These actions are
described in the Internal Registers section. The software flow for accessing the data buffer is based on the Sequential
Access scheme. The basic sequence is as follows:
•
•
•
•
•
•
Disable Interrupts
Write to Pointer Register High (specifying Auto-Increment mode)
Write to Pointer Register Low (this loads the address)
Enable Interrupts
Read or Write the Data Register (repeat as many times as necessary to empty or fill the buffer)
The pointer may now be read to determine how many transfers were completed.
The software flow for controlling the Configuration, Node ID, Tentative ID, and Next ID registers is generally limited to
the initialization sequence and the maintenance of the network map.
Additionally, it is necessary to understand the details of how the other Internal Registers are used in the transmit and
receive sequences and to know how the internal RAM buffer is properly set up. The sequence of events that tie these
actions together is discussed as follows.
6.4.1
SELECTING RAM PAGE SIZE
During normal operation, the 2K x 8 of RAM is divided into four pages of 512 bytes each. The page to be used is specified in the "Enable Transmit (Receive) from (to) Page fnn" command, where "nn" specifies page 0, 1, 2, or 3. This allows
the user to have constant control over the allocation of RAM.
When the Offset bit "f" (bit 5 of the "Enable Transmit (Receive) from (to) Page fnn" command word) is set to logic "1",
an offset of 256 bytes is added to the page specified. For example: to transmit from the second half of page 0, the command "Enable Transmit from Page fnn" (fnn=100 in this case) is issued by writing 0010 0011 to the Command Register.
This allows a finer resolution of the buffer pages without affecting software compatibility. This scheme is useful for appli-
2001-2020 Microchip Technology Inc.
DS00002704C-page 33
COM20020i Rev. D
cations which frequently use packet sizes of 256 bytes or less, especially for microcontroller systems with limited memory capacity. The remaining portions of the buffer pages which are not allocated for current transmit or receive packets
may be used as temporary storage for previous network data, packets to be sent later, or as extra memory for the system, which may be indirectly accessed.
If the device is configured to handle both long and short packets (see "Define Configuration" command), then receive
pages should always be 512 bytes long because the user never knows what the length of the receive packet will be. In
this case, the transmit pages may be made 256 bytes long, leaving at least 512 bytes free at any given time. Even if the
Command Chaining operation is being used, 512 bytes is still guaranteed to be free because Command Chaining only
requires two pages for transmit and two for receive (in this case, two 256 byte pages for transmit and two 512 byte pages
for receive, leaving 512 bytes free). Please note that it is the responsibility of software to reserve 512 bytes for each
receive page if the device is configured to handle long packets. The COM20020iD does not check page boundaries
during reception. If the device is configured to handle only short packets, then both transmit and receive pages may be
allocated as 256 bytes long, freeing at least 1KByte at any given time.
Even if the Command Chaining operation is being used, 1KByte is still guaranteed to be free because Command Chaining only requires two pages for transmit and two for receive (in this case, a total of four 256 byte pages, leaving 1K free).
The general rule which may be applied to determine where in RAM a page begins is as follows:
Address = (nn x 512) + (f x 256).
DS00002704C-page 34
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 6-2:
RAM BUFFER PACKET CONFIGURATION
ADDRESS
0
SHORT PACKET
FORMAT
LONG PACKET
FORMAT
SID
ADDRESS
0
1
DID
1
DID
2
COUNT = 256-N
2
0
3
COUNT = 512-N
NOT USED
COUNT
DATA BYTE 1
SID
NOT USED
DATA BYTE 2
COUNT
DATA BYTE 1
DATA BYTE 2
DATA BYTE N-1
255
DATA BYTE N
DATA BYTE N-1
NOT USED
511
511
DATA BYTE N
N = DATA PACKET LENGTH
SID = SOURCE ID
DID = DESTINATION ID
(DID = 0 FOR BROADCASTS)
6.4.2
TRANSMIT SEQUENCE
During a transmit sequence, the microcontroller selects a 256 or 512 byte segment of the RAM buffer and writes into it.
The appropriate buffer size is specified in the "Define Configuration" command. When long packets are enabled, the
COM20020iD interprets the packet as either a long or short packet, depending on whether the buffer address 2 contains
a zero or non-zero value. The format of the buffer is shown in Figure 6-2. Address 0 contains the Source Identifier (SID);
Address 1 contains the Destination Identifier (DID); Address 2 (COUNT) contains, for short packets, the value 256-N,
where N represents the number of information bytes in the message, or for long packets, the value 0, indicating that it
is indeed a long packet. In the latter case, Address 3 (COUNT) would contain the value 512-N, where N represents the
number of information bytes in the message. The SID in Address 0 is used by the receiving node to reply to the transmitting node. The COM20020iD puts the local ID in this location, therefore it is not necessary to write into this location.
Please note that a short packet may contain between 1 and 253 data bytes, while a long packet may contain between
257 and 508 data bytes. A minimum value of 257 exists on a long packet so that the COUNT is expressible in eight bits.
This leaves three exception packet lengths which do not fit into either a short or long packet; packet lengths of 254, 255,
or 256 bytes. If packets of these lengths must be sent, the user must add dummy bytes to the packet in order to make
the packet fit into a long packet.
2001-2020 Microchip Technology Inc.
DS00002704C-page 35
COM20020i Rev. D
Once the packet is written into the buffer, the microcontroller awaits a logic "1" on the TA bit, indicating that a previous
transmit command has concluded and another may be issued. Each time the message is loaded and a transmit command issued, it will take a variable amount of time before the message is transmitted, depending on the traffic on the
network and the location of the token at the time the transmit command was issued. The conclusion of the Transmit
Command will generate an interrupt if the Interrupt Mask allows it. If the device is configured for the Command Chaining
operation, please see the Command Chaining section for further detail on the transmit sequence. Once the TA bit
becomes a logic "1", the microcontroller may issue the "Enable Transmit from Page fnn" command, which resets the TA
and TMA bits to logic "0". If the message is not a BROADCAST, the COM20020iD automatically sends a FREE BUFFER
ENQUIRY to the destination node in order to send the message. At this point, one of four possibilities may occur.
The first possibility is if a free buffer is available at the destination node, in which case it responds with an ACKnowledgement. At this point, the COM20020iD fetches the data from the Transmit Buffer and performs the transmit
sequence. If a successful transmit sequence is completed, the TMA bit and the TA bit are set to logic "1". If the packet
was not transmitted successfully, TMA will not be set. A successful transmission occurs when the receiving node
responds to the packet with an ACK. An unsuccessful transmission occurs when the receiving node does not respond
to the packet.
The second possibility is if the destination node responds to the Free Buffer Enquiry with a Negative AcKnowledgement.
A NAK occurs when the RI bit of the destination node is a logic "1". In this case, the token is passed on from the transmitting node to the next node. The next time the transmitter receives the token, it will again transmit a FREE BUFFER
ENQUIRY. If a NAK is again received, the token is again passed onto the next node. The Excessive NAK bit of the Diagnostic Status Register is used to prevent an endless sending of FBE's and NAK's. If no limit of FBE-NAK sequences
existed, the transmitting node would continue issuing a Free Buffer Enquiry, even though it would continuously receive
a NAK as a response. The EXCNAK bit generates an interrupt (if enabled) in order to tell the microcontroller to disable
the transmitter via the "Disable Transmitter" command. This causes the transmission to be abandoned and the TA bit
to be set to a logic "1" when the node next receives the token, while the TMA bit remains at a logic "0". Please refer to
the Improved Diagnostics section for further detail on the EXCNAK bit.
The third possibility which may occur after a FREE BUFFER ENQUIRY is issued is if the destination node does not
respond at all. In this case, the TA bit is set to a logic "1", while the TMA bit remains at a logic "0". The user should
determine whether the node should try to reissue the transmit command.
The fourth possibility is if a non-traditional response is received (some pattern other than ACK or NAK, such as noise).
In this case, the token is not passed onto the next node, which causes the Lost Token Timer of the next node to time
out, thus generating a network reconfiguration.
The "Disable Transmitter" command may be used to cancel any pending transmit command when the COM20020iD
next receives the token. Normally, in an active network, this command will set the TA status bit to a logic "1" when the
token is received. If the "Disable Transmitter" command does not cause the TA bit to be set in the time it takes the token
to make a round trip through the network, one of three situations exists. Either the node is disconnected from the network, or there are no other nodes on the network, or the external receive circuitry has failed. These situations can be
determined by either using the improved diagnostic features of the COM20020iD or using another software timeout
which is greater than the worst case time for a round trip token pass, which occurs when all nodes transmit a maximum
length message.
6.4.3
RECEIVE SEQUENCE
A receive sequence begins with the RI status bit becoming a logic "1", which indicates that a previous reception has
concluded. The microcontroller will be interrupted if the corresponding bit in the Interrupt Mask Register is set to logic
"1". Otherwise, the microcontroller must periodically check the Status Register. Once the microcontroller is alerted to
the fact that the previous reception has concluded, it may issue the "Enable Receive to Page fnn" command, which
resets the RI bit to logic "0" and selects a new page in the RAM buffer. Again, the appropriate buffer size is specified in
the "Define Configuration" command. Typically, the page which just received the data packet will be read by the microcontroller at this point. Once the "Enable Receive to Page fnn" command is issued, the microcontroller attends to other
duties. There is no way of knowing how long the new reception will take, since another node may transmit a packet at
any time. When another node does transmit a packet to this node, and if the "Define Configuration" command has
enabled the reception of long packets, the COM20020iD interprets the packet as either a long or short packet, depending on whether the content of the buffer location 2 is zero or non-zero. The format of the buffer is shown in Figure 6-3.
Address 0 contains the Source Identifier (SID), Address 1 contains the Destination Identifier (DID), and Address 2 contains, for short packets, the value 256-N, where N represents the message length, or for long packets, the value 0, indicating that it is indeed a long packet. In the latter case, Address 3 contains the value 512-N, where N represents the
message length. Note that on reception, the COM20020iD deposits packets into the RAM buffer in the same format that
the transmitting node arranges them, which allows for a message to be received and then retransmitted without rear-
DS00002704C-page 36
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
ranging any bytes in the RAM buffer other than the SID and DID. Once the packet is received and stored correctly in
the selected buffer, the COM20020iD sets the RI bit to logic "1" to signal the microcontroller that the reception is complete.
FIGURE 6-3:
COMMAND CHAINING STATUS REGISTER QUEUE
MSB
TRI
LSB
RI
TA
POR
TEST
TRI
6.5
RECON
TMA
TTA
TMA
TTA
Command Chaining
The Command Chaining operation allows consecutive transmissions and receptions to occur without host microcontroller intervention.
Through the use of a dual two-level FIFO, commands to be transmitted and received, as well as the status bits, are
pipelined.
In order for the COM20020iD to be compatible with previous Microchip ARCNET device drivers, the device defaults to
the non-chaining mode. In order to take advantage of the Command Chaining operation, the Command Chaining Mode
must be enabled via a logic "1" on bit 6 of the Configuration Register.
In Command Chaining, the Status Register appears as in Figure 6-3.
The following is a list of Command Chaining guidelines for the software programmer. Further detail can be found in the
Transmit Command Chaining and Receive Command Chaining sections.
• The device is designed such that the interrupt service routine latency does not affect performance.
• Up to two outstanding transmissions and two outstanding receptions can be pending at any given time. The commands may be given in any order.
• Up to two outstanding transmit interrupts and two outstanding receive interrupts are stored by the device, along
with their respective status bits.
• The Interrupt Mask bits act on TTA (Rising Transition on Transmitter Available) for transmit operations and TRI
(Rising Transition of Receiver Inhibited) for receive operations. TTA is set upon completion of a packet transmission only. TRI is set upon completion of a packet reception only. Typically there is no need to mask the TTA and
TRI bits after clearing the interrupt.
• The traditional TA and RI bits are still available to reflect the present status of the device.
6.5.1
TRANSMIT COMMAND CHAINING
When the processor issues the first "Enable Transmit to Page fnn" command, the COM20020iD responds in the usual
manner by resetting the TA and TMA bits to prepare for the transmission from the specified page. The TA bit can be
used to see if there is currently a transmission pending, but the TA bit is really meant to be used in the non-chaining
mode only. The TTA bits provide the relevant information for the device in the Command Chaining mode.
In the Command Chaining Mode, at any time after the first command is issued, the processor can issue a second
"Enable Transmit from Page fnn" command. The COM20020iD stores the fact that the second transmit command was
issued, along with the page number.
After the first transmission is completed, the COM20020iD updates the Status Register by setting the TTA bit, which
generates an interrupt. The interrupt service routine should read the Status Register. At this point, the TTA bit will be
found to be a logic "1" and the TMA (Transmit Message Acknowledge) bit will tell the processor whether the transmission
was successful. After reading the Status Register, the "Clear Transmit Interrupt" command is issued, thus resetting the
TTA bit and clearing the interrupt. Note that only the "Clear Transmit Interrupt" command will clear the TTA bit and the
interrupt. It is not necessary, however, to clear the bit or the interrupt right away because the status of the transmit oper-
2001-2020 Microchip Technology Inc.
DS00002704C-page 37
COM20020i Rev. D
ation is double buffered in order to retain the results of the first transmission for analysis by the processor. This information will remain in the Status Register until the "Clear Transmit Interrupt" command is issued. Note that the interrupt will
remain active until the command is issued, and the second interrupt will not occur until the first interrupt is acknowledged. The COM20020iD guarantees a minimum of 200nS (at EF=1) interrupt inactive time interval between interrupts.
The TMA bit is also double buffered to reflect whether the appropriate transmission was a success. The TMA bit should
only be considered valid after the corresponding TTA bit has been set to a logic "1". The TMA bit never causes an interrupt.
When the token is received again, the second transmission will be automatically initiated after the first is completed by
using the stored "Enable Transmit from Page fnn" command. The operation is as if a new "Enable Transmit from Page
fnn" command has just been issued. After the first Transmit status bits are cleared, the Status Register will again be
updated with the results of the second transmission and a second interrupt resulting from the second transmission will
occur. The COM20020iD guarantees a minimum of 200ns (at EF=1) interrupt inactive time interval before the following
edge.
The Transmitter Available (TA) bit of the Interrupt Mask Register now masks only the TTA bit of the Status Register, not
the TA bit as in the non-chaining mode. Since the TTA bit is only set upon transmission of a packet (not by RESET), and
since the TTA bit may easily be reset by issuing a "Clear Transmit Interrupt" command, there is no need to use the TA
bit of the Interrupt Mask Register to mask interrupts generated by the TTA bit of the Status Register.
In Command Chaining mode, the "Disable Transmitter" command will cancel the oldest transmission. This permits canceling a packet destined for a node not ready to receive. If both packets should be canceled, two "Disable Transmitter"
commands should be issued.
6.5.2
RECEIVE COMMAND CHAINING
Like the Transmit Command Chaining operation, the processor can issue two consecutive "Enable Receive from Page
fnn" commands.
After the first packet is received into the first specified page, the TRI bit of the Status Register will be set to logic "1",
causing an interrupt. Again, the interrupt need not be serviced immediately. Typically, the interrupt service routine will
read the Status Register. At this point, the RI bit will be found to be a logic "1". After reading the Status Register, the
"Clear Receive Interrupt" command should be issued, thus resetting the TRI bit and clearing the interrupt. Note that only
the "Clear Receive Interrupt" command will clear the TRI bit and the interrupt. It is not necessary, however, to clear the
bit or the interrupt right away because the status of the receive operation is double buffered in order to retain the results
of the first reception for analysis by the processor, therefore the information will remain in the Status Register until the
"Clear Receive Interrupt" command is issued. Note that the interrupt will remain active until the "Clear Receive Interrupt"
command is issued, and the second interrupt will be stored until the first interrupt is acknowledged. A minimum of 200nS
(at EF=1) interrupt inactive time interval between interrupts is guaranteed.
The second reception will occur as soon as a second packet is sent to the node, as long as the second "Enable Receive
to Page fnn" command was issued. The operation is as if a new "Enable Receive to Page fnn" command has just been
issued. After the first Receive status bits are cleared, the Status Register will again be updated with the results of the
second reception and a second interrupt resulting from the second reception will occur.
In the COM20020iD, the Receive Inhibit (RI) bit of the Interrupt Mask Register now masks only the TRI bit of the Status
Register, not the RI bit as in the non-chaining mode. Since the TRI bit is only set upon reception of a packet (not by
RESET), and since the TRI bit may easily be reset by issuing a "Clear Receive Interrupt" command, there is no need to
use the RI bit of the Interrupt Mask Register to mask interrupts generated by the TRI bit of the Status Register. In Command Chaining mode, the "Disable Receiver" command will cancel the oldest reception, unless the reception has
already begun. If both receptions should be canceled, two "Disable Receiver" commands should be issued.
6.6
6.6.1
Reset Details
INTERNAL RESET LOGIC
The COM20020iD includes special reset circuitry to provide smooth operation during reset. Special care is taken to
assure proper operation in a variety of systems and modes of operation. The COM20020iD contains digital filter circuitry
and a Schmitt Trigger on the nRESET signal to reject glitches in order to ensure fault-free operation.
The COM20020iD supports two reset options; software and hardware reset. A software reset is generated when a logic
"1" is written to bit 7 of the Configuration Register. The device remains in reset as long as this bit is set. The software
reset does not affect the microcontroller interface modes determined after hardware reset, nor does it affect the contents
DS00002704C-page 38
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
of the Address Pointer Registers, the Configuration Register, or the Setup1 Register. A hardware reset occurs when a
low signal is asserted on the nRESET input. The minimum reset pulse width is 5TXTL. This pulse width is used by the
internal digital filter, which filters short glitches to allow only valid resets to occur.
Upon reset, the transmitter portion of the device is disabled and the internal registers assume those states outlined in
the Internal Registers section. After the nRESET signal is removed the user may write to the internal registers. Since
writing a non-zero value to the Node ID Register wakes up the COM20020iD core, the Setup1 Register should be written
before the Node ID Register. Once the Node ID Register is written to, the COM20020iD reads the value and executes
two write cycles to the RAM buffer. Address 0 is written with the data D1H and address 1 is written with the Node ID.
The data pattern D1H was chosen arbitrarily, and is meant to provide assurance of proper microsequencer operation.
6.7
6.7.1
Initialization Sequence
BUS DETERMINATION
Writing to and reading from an odd address location from the COM20020iD's address space causes the COM20020iD
to determine the appropriate bus interface. When the COM20020iD is powered on the internal registers may be written
to. Since writing a non-zero value to the Node ID Register wakes up the core, the Setup1 Register should be written to
before the Node ID Register. Until a non-zero value is placed into the NID Register, no microcode is executed, no tokens
are passed by this node, and no reconfigurations are generated by this node. Once a non-zero value is placed in the
register, the core wakes up, but the node will not attempt to join the network until the TX Enable bit of the Configuration
Register is set.
Before setting the TX Enable bit, the software may make some determinations. The software may first observe the
Receive Activity and the Token Seen bits of the Diagnostic Status Register to verify the health of the receiver and the
network.
Next, the uniqueness of the Node ID value placed in the Node ID Register is determined. The TX Enable bit should still
be a logic "0" until it is ensured that the Node ID is unique. If this node ID already exists, the Duplicate ID bit of the Diagnostic Status Register is set after a maximum of 420mS (or 840mS if the ET1 and ET2 bits are other than 1,1). To determine if another node on the network already has this ID, the COM20020iD compares the value in the Node ID Register
with the DID's of the token, and determines whether there is a response to it. Once the Diagnostic Status Register is
read, the DUPID bit is cleared. The user may then attempt a new ID value, wait 420mS before checking the Duplicate
ID bit, and repeat the process until a unique Node ID is found. At this point, the TX Enable bit may be set to allow the
node to join the network. Once the node joins the network, a reconfiguration occurs, as usual, thus setting the
MYRECON bit of the Diagnostic Status Register.
The Tentative ID Register may be used to build a network map of all the nodes on the network, even once the
COM20020iD has joined the network. Once a value is placed in the Tentative ID Register, the COM20020iD looks for a
response to a token whose DID matches the Tentative ID Register. The software can record this information and continue placing Tentative ID values into the register to continue building the network map. A complete network map is only
valid until nodes are added to or deleted from the network. Note that a node cannot detect the existence of the next
logical node on the network when using the Tentative ID. To determine the next logical node, the software should read
the Next ID Register.
6.8
Improved Diagnostics
The COM20020iD allows the user to better manage the operation of the network through the use of the internal Diagnostic Status Register.
A high level on the My Reconfiguration (MYRECON) bit indicates that the Token Reception Timer of this node expired,
causing a reconfiguration by this node. After the Reconfiguration (RECON) bit of the Status Register interrupts the
microcontroller, the interrupt service routine will typically read the MYRECON bit of the Diagnostic Status Register.
Reading the Diagnostic Status Register resets the MYRECON bit. Successive occurrences of a logic "1" on the
MYRECON bit indicates that a problem exists with this node. At that point, the transmitter should be disabled so that
the entire network is not held down while the node is being evaluated.
The Duplicate ID (DUPID) bit is used before the node joins the network to ensure that another node with the same ID
does not exist on the network. Once it is determined that the ID in the Node ID Register is unique, the software should
write a logic "1" to bit 5 of the Configuration Register to enable the basic transmit function. This allows the node to join
the network.
The Receive Activity (RCVACT) bit of the Diagnostic Status Register will be set to a logic "1" whenever activity (logic
"1") is detected on the RXIN pin.
2001-2020 Microchip Technology Inc.
DS00002704C-page 39
COM20020i Rev. D
The Token Seen (TOKEN) bit is set to a logic "1" whenever any token has been seen on the network (except those
tokens transmitted by this node).
The RCVACT and TOKEN bits may help the user to troubleshoot the network or the node. If unusual events are occurring on the network, the user may find it valuable to use the TXEN bit of the Configuration Register to qualify events.
Different combinations of the RCVACT, TOKEN, and TXEN bits, as shown indicate different situations:
6.8.1
NORMAL RESULTS
RCVACT=1, TOKEN=1, TXEN=0: The node is not part of the network. The network is operating properly without this
node.
RCVACT=1, TOKEN=1, TXEN=1: The node sees receive activity and sees the token. The basic transmit function is
enabled. Network and node are operating properly.
MYRECON=0, DUPID=0, RCVACT=1, TXEN=0, TOKEN=1: Single node network.
6.8.2
ABNORMAL RESULTS
RCVACT=1, TOKEN=0, TXEN=X: The node sees receive activity, but does not see the token. Either no other nodes
exist on the network, some type of data corruption exists, the media driver is malfunctioning, the topology is set up incorrectly, there is noise on the network, or a reconfiguration is occurring.
RCVACT=0, TOKEN=0, TXEN=1: No receive activity is seen and the basic transmit function is enabled. The transmitter
and/or receiver are not functioning properly.
RCVACT=0, TOKEN=0, TXEN=0: No receive activity and basic transmit function disabled. This node is not connected
to the network.
The Excessive NAK (EXCNAK) bit is used to replace a timeout function traditionally implemented in software. This function is necessary to limit the number of times a sender issues a FBE to a node with no available buffer. When the destination node replies to 128 FBEs with 128 NAKs or 4 FBEs with 4 NAKs, the EXCNAK bit of the sender is set,
generating an interrupt. At this point the software may abandon the transmission via the "Disable Transmitter" command. This sets the TA bit to logic "1" when the node next receives the token, to allow a different transmission to occur.
The timeout value for the EXNACK bit (128 or 4) is determined by the FOUR-NAKS bit on the Setup1 Register.
The user may choose to wait for more NAK's before disabling the transmitter by taking advantage of the wraparound
counter of the EXCNAK bit. When the EXCNAK bit goes high, indicating 128 or 4 NAKs, the "POR Clear Flags" command maybe issued to reset the bit so that it will go high again after another count of 128 or 4. The software may count
the number of times the EXCNAK bit goes high, and once the final count is reached, the "Disable Transmitter" command
may be issued.
The New Next ID bit permits the software to detect the withdrawal or addition of nodes to the network.
The Tentative ID bit allows the user to build a network map of those nodes existing on the network. This feature is useful
because it minimizes the need for human intervention. When a value placed in the Tentative ID Register matches the
Node ID of another node on the network, the TENTID bit is set, telling the software that this NODE ID already exists on
the network. The software should periodically place values in the Tentative ID Register and monitor the New Next ID bit
to maintain an updated network map.
6.9
Oscillator
The COM20020iD contains circuitry which, in conjunction with an external parallel resonant crystal or TTL clock, forms
an oscillator.
If an external crystal is used, two capacitors are needed (one from each leg of the crystal to ground). No external resistor
is required, since the COM20020iD contains an internal resistor. The crystal must have an accuracy of 0.020% or better.
The oscillation frequency range is from 10 MHz to 20 MHz.
The crystal must have an accuracy of 0.010% or better when the internal clock multiplier is turned on. The oscillation
frequency must be 20MHz when the internal clock multiplier is turned on.
The XTAL2 side of the crystal may be loaded with a single 74HC-type buffer in order to generate a clock for other
devices.
The user may attach an external TTL clock, rather than a crystal, to the XTAL1 signal. In this case, a 390 pull-up resistor is required on XTAL1, while XTAL2 should be left unconnected.
DS00002704C-page 40
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
7.0
OPERATIONAL DESCRIPTION
7.1
Maximum Ratings*
Operating Temperature Range.....................................................................................................................0oC to +70oC
Storage Temperature Range...................................................................................................................-55oC to +150oC
Lead Temperature (soldering, 10 seconds).......................................................................................................... +325 oC
Positive Voltage on any pin, with respect to ground ......................................................................................... VDD+0.3V
Negative Voltage on any pin, with respect to ground ................................................................................................-0.3V
Maximum VDD ............................................................................................................................................................+7V
* Stresses above those listed may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other condition above those indicated in the operational sections of this specification is not implied.
Note:
7.2
When powering this device from laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes or
"glitches" on their outputs when the AC power is switched on or off. In addition, voltage transients on the
AC power line may appear on the DC output. If this possibility exists it is suggested that a clamp circuit be
used.
DC Electrical Characteristics
VDD=5.0V±10%
COM20020: TA=0oC to +70oC, COM20020I: TA=-40oC to +85oC
Parameter
Low Input Voltage 1
(All inputs except A2,
XTAL1, nRESET, nRD,
nWR, and RXIN)
High Input Voltage 1
(All inputs except A2,
XTAL1, nRESET, nRD,
nWR, and RXIN)
Low Input Voltage 2
(XTAL1)
High Input Voltage 2
(XTAL1)
Low to High Threshold
Input Voltage
(A2, nRESET, nRD, nWR, and
RXIN)
High to Low Threshold
Input Voltage
(A2, nRESET, nRD, nWR, and
RXIN)
2001-2020 Microchip Technology Inc.
Symbol
MIN
TYP
VIL1
VIH1
Unit
0.8
V
TTL Levels
V
TTL Levels
V
TTL Clock Input
2.0
1.0
VIL2
VIH2
MAX
4.0
Comment
V
VILH
1.8
V
VIHL
1.2
V
Schmitt Trigger,
All Values at VDD =
5V
DS00002704C-page 41
COM20020i Rev. D
Parameter
Low Output Voltage 1
(nPULSE1 in Push/Pull
Mode, nPULSE2,
NTXEN)
High Output Voltage 1
(nPULSE1 in Push/Pull
Mode, nPULSE2,
nTXEN)
Low Output Voltage 2
(D0-D7)
High Output Voltage 2
(D0-D7)
Low Output Voltage 3
(nINTR)
High Output Voltage 3
(nINTR)
Low Output Voltage 4
(nPULSE1 in Open-Drain
Mode)
Dynamic VDD Supply
Current
Symbol
MIN
TYP
MAX
Unit
0.4
V
ISINK=4mA
V
ISOURCE=-2mA
VOL1
VOH1
2.4
VOH1C
0.8 x VDD
ISOURCE=-200µA
VOL2
0.4
VOH2
V
ISINK=16mA
V
ISOURCE=-12mA
V
ISINK=24mA
V
ISOURCE=-10mA
V
ISINK=48mA
Open Drain Driver
mA
5 Mbps
All Outputs Open
200
A
VIN=0.0V
±10
A
VSS < VIN < VDD
2.4
VOL3
0.8
VOH3
2.4
VOL4
0.5
IDD
40
IP
80
Input Pull-up Current
(nPULSE1 in Open-Drain
Mode, A1, AD0-AD2,
D3-D7)
Input Leakage Current
(All inputs except A1,
AD0-AD2, D3-D7,
XTAL1, XTAL2
Comment
IL
CAPACITANCE (TA = 25C; fC = 1MHz; VDD = 0V)
Output and I/O pins capacitive load specified as follows:
Parameter
Input Capacitance
Output Capacitance 1
(All outputs except XTAL2,
nPULSE1 in Push/Pull Mode)
Output Capacitance 2
(nPULSE1, in BackPlane
Mode Only - Open
Drain)
DS00002704C-page 42
Symbol
MIN
TYP
MAX
Unit
CIN
5.0
pF
COUT1
45
pF
COUT2
400
pF
Comment
Maximum Capacitive
Load which can be supported by each output.
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
AC Measurements are taken at the following points:
Outputs:
Inputs:
t
t
2.0V
2.4V
1.4V
50%
0.8V
0.4V
t
2.4V
2.0V
1.4V
0.4V
50%
0.8V
t
Inputs are driven at 2.4V for logic "1" and 0.4 V for logic "0" except XTAL1 pin.
Outputs are measured at 2.0V min. for logic "1" and 0.8V max. for logic "0".
2001-2020 Microchip Technology Inc.
DS00002704C-page 43
COM20020i Rev. D
8.0
TIMING DIAGRAMS
FIGURE 8-1:
MULTIPLEXED BUS, 68XX-LIKE CONTROL SIGNALS; READ CYCLE
AD0-AD2,
D3-D7
VALID DATA
VALID
t1
nCS
t2,
t4
t3
t12
t11
ALE
t6
t5
nDS
t7
t13
t14
Note 2
t8
t9
DIR
t10
MUST BE: RBUSTMG bit = 0
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
t14
Address Setup to ALE Low
Address Hold from ALE Low
nCS Setup to ALE Low
nCS Hold from ALE Low
ALE Low to nDS Low
nDS Low to Valid Data
nDS High to Data High Impedance
Cycle Time (nDS Low to Next Time Low)
DIR Setup to nDS Active
DIR Hold from nDS Inactive
ALE High Width
ALE Low Width
nDS Low Width
nDS High Width
min
20
10
10
10
15
0
4TARB*
10
10
20
20
60
20
max
40
20
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
Note 2: Read cycle for Address Pointer Low/High Registers occurring after an access
to Data Register requires a minimum of 5TARB from the trailing edge of nDS to
the leading edge of the next nDS.
DS00002704C-page 44
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 8-2:
MULTIPLEXED BUS, 80XX-LIKE CONTROL SIGNALS; READ CYCLE
AD0-AD2,
D3-D7
VALID DATA
VALID
t1
t2,
t4
nCS
t3
ALE
t10
t9
nRD
t5
nWR
t6
t13 Note 3
t7
t11
t8
t12
Note 2
MUST BE: RBUSTMG bit = 0
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
Address Setup to ALE Low
Address Hold from ALE Low
nCS Setup to ALE Low
nCS Hold from ALE Low
ALE Low to nRD Low
nRD Low to Valid Data
nRD High to Data High Impedance
Cycle Time (nRD Low to Next Time Low)
ALE High Width
ALE Low Width
nRD Low Width
nRD High Width
nWR
to nRD Low
min
20
10
10
10
15
0
4TARB*
20
20
60
20
20
max
40
20
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
Note 2: Read cycle for Address Pointer Low/High Registers occurring after a read from
Data Register requires a minimum of 5TARB from the trailing edge of nRD to the
leading edge of the next nRD.
Note 3: Read cycle for Address Pointer Low/High Registers occurring after a write to
Data Register requires a minimum of 5TARB from the trailing edge of nWR to the
leading edge of nRD.
2001-2020 Microchip Technology Inc.
DS00002704C-page 45
COM20020i Rev. D
FIGURE 8-3:
MULTIPLEXED BUS, 68XX-LIKE CONTROL SIGNALS; WRITE CYCLE
D0-AD2,
A
D3-D7
VALID DATA
VALID
t1
t2,
t4
nCS
t3
t12
t11
ALE
t5
nDS
t7
t6
Note 2
t8**
t13
DIR
t14
t9
t10
min
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
t14
Address Setup to ALE Low
Address Hold from ALE Low
nCS Setup to ALE Low
nCS Hold from ALE Low
ALE Low to nDS Low
Valid Data Setup to nDS High
Data Hold from nDS High
Cycle Time (nDS
to Next
DIR Setup to nDS Active
DIR Hold from nDS Inactive
ALE High Width
ALE Low Width
nDS Low Width
nDS High Width
t8
)**
20
10
10
10
15
30
10
4TARB*
10
10
20
20
20
20
max
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
The Microcontroller typically accesses the COM20020 on every other cycle.
Note 1:
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
** Note 2:
Any cycle occurring after a write to Address Pointer Low Register requires a
minimum of 4TARB from the trailing edge of nDS to the leading edge of the
next nDS.
Write cycle for Address Pointer Low Register occurring after an access to
Data Register requires a minimum of 5TARB from the trailing edge of nDS to
the leading edge of the next nDS.
DS00002704C-page 46
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 8-4:
MULTIPLEXED BUS, 80XX-LIKE CONTROL SIGNALS; WRITE CYCLE
D0-AD2,
A
D3-D7
VALID
t1
VALID DATA
t2,
t4
nCS
t3
t10
t9
ALE
t5
nWR
nRD
t13
Address Setup to ALE Low
Address Hold from ALE Low
nCS Setup to ALE Low
nCS Hold from ALE Low
ALE Low to nDS Low
Valid Data Setup to nDS High
Data Hold from nDS High
Cycle Time (nWR
to Next
ALE High Width
ALE Low Width
nWR Low Width
nWR High Width
nRD
to nWR Low
Note 2
t8**
t12
t11
Note 3
min
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
t7
t6
)**
20
10
10
10
15
30
10
4TARB*
20
20
20
20
20
max
t8
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
The Microcontroller typically accesses the COM20020 on every other cycle.
Note 1:
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
** Note 2:
Any cycle occurring after a write to Address Pointer Low Register requires a
minimum of 4TARB from the trailing edge of nWR to the leading edge of the
next nWR.
Write cycle for Address Pointer Low Register occurring after a write to Data
Register requires a minimum of 5TARB from the trailing edge of nWR to the
leading edge of the next nWR.
Note 3:
Write cycle for Address Pointer Low Register occurring after a read from Data
Register requires a minimum of 5TARB from the trailing edge of nRD to the
leading edge of nWR.
2001-2020 Microchip Technology Inc.
DS00002704C-page 47
COM20020i Rev. D
FIGURE 8-5:
NON-MULTIPLEXED BUS, 80XX-LIKE CONTROL SIGNALS; READ CYCLE
VALID
A0-A2
t1
t2
nCS
t4
t3
t5
Note 3
t10
nRD
t8
t7
t6
nWR
D0-D7
t9
Note 2
VALID DATA
CASE 1: RBUSTMG bit = 0
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
Address Setup to nRD Active
Address Hold from nRD Inactive
nCS Setup to nRD Active
nCS Hold from nRD Inactive
Cycle Time (nRD Low to Next Time Low)
nRD Low to Valid Data
nRD High to Data High Impedance
nRD Low Width
nRD High Width
nWR
to nRD Low
min
max
15
10
5**
0
4TARB*
0
60
20
20
40**
20
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
** nCS may become active after control becomes active, but the access time (t6)
will now be 45nS measured from the leading edge of nCS.
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
** Note 2: Read cycle for Address Pointer Low/High Registers occurring after a read from
Data Register requires a minimum of 5TARB from the trailing edge of nRD to the
leading edge of the next nRD.
Note 3: Read cycle for Address Pointer Low/High Registers occurring after a write to
Data Register requires a minimum of 5TARB from the trailing edge of nWR to the
leading edge of nRD.
DS00002704C-page 48
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 8-6:
NON-MULTIPLEXED BUS, 80XX-LIKE CONTROL SIGNALS; READ CYCLE
VALID
A0-A2
t1
t2
nCS
t4
t3
t5
Note 3
t10
nRD
t8
t7
t6
nWR
D0-D7
t9
Note 2
VALID DATA
CASE 2: RBUSTMG bit = 1
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
Address Setup to nRD Active
Address Hold from nRD Inactive
nCS Setup to nRD Active
nCS Hold from nRD Inactive
Cycle Time (nRD Low to Next Time Low)
nRD Low to Valid Data
nRD High to Data High Impedance
nRD Low Width
nRD High Width
nWR
to nRD Low
min
max
-5
0
-5
0
4TARB*+30
0
100
30
20
60**
20
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
** t6 is measured from the latest active (valid) timing among nCS, nRD, A0-A2.
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
Note 2: Read cycle for Address Pointer Low/High Registers occurring after a read from
Data Register requires a minimum of 5TARB from the trailing edge of nRD to the
leading edge of the next nRD.
Note 3: Read cycle for Address Pointer Low/High Registers occurring after a write to
Data Register requires a minimum of 5TARB from the trailing edge of nWR to the
leading edge of nRD.
2001-2020 Microchip Technology Inc.
DS00002704C-page 49
COM20020i Rev. D
FIGURE 8-7:
NON-MULTIPLEXED BUS, 68XX-LIKE CONTROL SIGNALS; READ CYCLE
A0-A2
VALID
t1
t2
nCS
t4
t3
DIR
t7
t5
t6
t10
nDS
t9
t8
D0-D7
t11
Note 2
VALID DATA
CASE 1: RBUSTMG bit = 0
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
Address Setup to nDS Active
Address Hold from nDS Inactive
nCS Setup to nDS Active
nCS Hold from nDS Inactive
DIR Setup to nDS Active
Cycle Time (nDS Low to Next Time Low)
DIR Hold from nDS Inactive
nDS Low to Valid Data
nDS High to Data High Impedence
nDS Low Width
nDS High Width
min
max
15
10
5**
0
10
4TARB*
10
0
60
20
40**
20
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
** nCS may become active after control becomes active, but the access time (t8) will
now be 45nS measured from the leading edge of nCS.
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
Note 2: Read cycle for Address Pointer Low/High Registers occurring after an access
to Data Register requires a minimum of 5TARB from the trailing edge of nDS to
the leading edge of the next nDS.
DS00002704C-page 50
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 8-8:
NON-MULTIPLEXED BUS, 68XX-LIKE CONTROL SIGNALS; READ CYCLE
A0-A2
VALID
t1
t2
nCS
t4
t3
DIR
t7
t5
t6
t10
nDS
t9
t8
D0-D7
t11
Note 2
VALID DATA
CASE 2: RBUSTMG bit = 1
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
Address Setup to nDS Active
Address Hold from nDS Inactive
nCS Setup to nDS Active
nCS Hold from nDS Inactive
DIR Setup to nDS Active
Cycle Time (nDS Low to Next Time Low)
DIR Hold from nDS Inactive
nDS Low to Valid Data
nDS High to Data High Impedence
nDS Low Width
nDS High Width
min
max
-5
0
-5
0
10
4TARB*+30
10
0
100
30
60**
20
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
** t8 is measured from the latest active (valid) timing among nCS, nDS, A0-A2.
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
Note 2: Read cycle for Address Pointer Low/High Registers occurring after an access
to Data Register requires a minimum of 5TARB from the trailing edge of nDS to
the leading edge of the next nDS.
2001-2020 Microchip Technology Inc.
DS00002704C-page 51
COM20020i Rev. D
FIGURE 8-9:
NON-MULTIPLEXED BUS, 80XX-LIKE CONTROL SIGNALS; WRITE CYCLE
A0-A2
VALID
t1
t2
nCS
t4
nRD
Note 3
t10
t3
t9
t8
t5
nWR
t6
D0-D7
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t7
Note 2
t5**
VALID DATA
Parameter
Address Setup to nWR Active
Address Hold from nWR Inactive
nCS Setup to WR Active
nCS Hold from nWR Inactive
Cycle Time (nWR
to Next
)**
Valid Data Setup to nWR High
Data Hold from nWR High
nWR Low Width
nWR High Width
nRD
to nWR Low
min
15
10
5
0
4TARB*
30***
10
20
20
20
max
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
***: nCS may become active after control becomes active, but the data setup time will now
be 30 nS measured from the later of nCS falling or Valid Data available.
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
**Note 2: Any cycle occurring after a write to the Address Pointer Low Register
requires a minimum of 4TARB from the trailing edge of nWR to the leading edge
of the next nWR.
Write cycle for Address Pointer Low Register occurring after a write to Data
Register requires a minimum of 5TARB from the trailing edge of nWR to the
leading edge of the next nWR.
Note 3: Write cycle for Address Pointer Low Register occurring after a read from Data
Register requires a minimum of 5TARB from the trailing edge of nRD to the
leading edge of nWR.
DS00002704C-page 52
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 8-10:
NON-MULTIPLEXED BUS, 68XX-LIKE CONTROL SIGNALS; WRITE CYCLE
A0-A2
VALID
t1
t2
nCS
t4
t3
DIR
t5
t7
t10
nDS
t8
t9
t6
VALID DATA
D0-D7
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t11
Note 2
t6**
Parameter
Address Setup to nDS Active
Address Hold from nDS Inactive
nCS Setup to nDS Active
nCS Hold from nDS Inactive
DIR Setup to nDS Active
Cycle Time (nDS
to Next Time
DIR Hold from nDS Inactive
Valid Data Setup to nDS High
Data Hold from nDS High
nDS Low Width
nDS High Width
)**
min
15
10
5
0
10
4TARB*
10
30***
10
20
20
max
units
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
nS
* TARB is the Arbitration Clock Period
TARB is identical to Topr if SLOW ARB = 0
TARB is twice Topr if SLOW ARB = 1
Topr is the period of operation clock. It depends on CKUP1 and CKUP0 bits
***: nCS may become active after control becomes active, but the data setup time will now
be 30 nS measured from the later of nCS falling or Valid Data available.
Note 1: The Microcontroller typically accesses the COM20020 on every other cycle.
Therefore, the cycle time specified in the microcontroller's datasheet
should be doubled when considering back-to-back COM20020 cycles.
**Note 2: Any cycle occurring after a write to the Address Pointer Low Register
requires a minimum of 4TARB from the trailing edge of nDS to the leading edge
of the next nDS.
Write cycle for Address Pointer Low Registers occurring after an access to
Data Register requires a minimum of 5TARB from the trailing edge of nDS to
the leading edge of the next nDS.
2001-2020 Microchip Technology Inc.
DS00002704C-page 53
COM20020i Rev. D
FIGURE 8-11:
NORMAL MODE TRANSMIT OR RECEIVE TIMING
nTXEN
t4
t5
t2
t1
nPULSE1
LAST BIT
(400 nS BIT TIME)
t3
t2
t1
nPULSE2
t6
RXIN
t8
t7
Parameter
t1
t2
t3
t4
t5
t6
t7
t8
nPULSE1, nPULSE2 Pulse Width
nPULSE1, nPULSE2 Period
nPULSE1, nPULSE2 Overlap
nTXEN Low to nPULSE1 Low
Beginning of Last Bit Time to nTXEN High
RXIN Active Pulse Width
RXIN Period
RXIN Inactive Pulse Width
min
-10
850
250
10
20
typ
100
400
0
100
400
max
+10
950
350
units
nS
nS
nS
nS
nS
nS
nS
nS
Note: Use Only 2.5 Mbps
Note:
These signals are to and from the hybrid.
DS00002704C-page 54
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE 8-12:
BACKPLANE MODE TRANSMIT OR RECEIVE TIMING
nTXEN
t1
t13
t3
nPULSE1
t2
t9
LAST BIT
(400 nS BIT TIME)
t4
t5
nPULSE2
(Internal Clk)
t8
t6
t7
t10
t12
RXIN
t11
Parameter
t9
t13
nPULSE2 High to nTXEN Low
nPULSE1 Pulse Width
nPULSE1 Period
nPULSE2 Low to nPULSE1 Low
nPULSE2 High Time
nPULSE2 Low Time
nPULSE2 Period
nPULSE2 High to nTXEN High
(First Rising Edge on nPULSE2 after Last Bit Time)
nTXEN Low to first nPULSE1 Low**
Beginning Last Bit Time to nTXEN High**
t10
t11
t12
RXIN Active Pulse Width
RXIN Period
RXIN Inactive Pulse Width
t1
t2
t3
t4
t5
t6
t7
t8
min
typ
-25
max
50
units
-25
50
nS
nS
nS
nS
nS
nS
nS
nS
650
450
750
550
nS
nS
-25
200*
400*
50
100*
100*
200*
10
20
200*
400*
nS
nS
nS
Above values are for 2.5 Mbps.
Other Data Rates are shown below.
TDR is the Data Rate Period
*t5, t6 = TDR/4
*t2, t7, t10 = TDR/2
*t3, t11 = TDR
**t9 = 47 x TDR +/- 50 nS
**t13 =
Note:
5
4
x TDR +/- 50 nS
These signals are to and from the differential driver or the cable.
2001-2020 Microchip Technology Inc.
DS00002704C-page 55
COM20020i Rev. D
FIGURE 8-13:
TTL INPUT TIMING ON XTAL1 PIN
4.0V
t1
t3
t2
50% of VDD
1.0V
XTAL1
Parameter
t1
t2
t3
t4
t5
min
Input Clock High Time
Input Clock Low Time
Input Clock Period
Input Clock Frequency
Frequency Accuracy*
typ
10
10
25
10
-200
max
100
40
200
units
nS
nS
nS
MHz
ppm
Note*: Input clock frequency must be 20 MHz (+-100ppm or better) to use the internal Clock Multiplier.
t5 is applied to crystal oscillaton.
FIGURE 8-14:
RESET AND INTERRUPT TIMING
t1
nRESET
nINTR
t2
Parameter
t1
t2
nRESET Pulse Width***
nINTR High to Next nINTR Low
min
EF = 0
EF = 1
typ
max
units
5TXTL*
TDR**/2
4TXTL*
Note*: TXTL is period of external XTAL oscillation frequency.
Note**: TDR is period of Data Rate (i.e. at 2.5 Mbps, TDR = 400 nS)
Note***: When the power is turned on, t1 is measured from stable XTAL
oscillation after VDD was over 4.5V.
DS00002704C-page 56
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
9.0
PACKAGE OUTLINE
COM20020ID 48-PIN TQFP PACKAGE OUTLINE
Note: For the most current package drawings,
see the Microchip Packaging Specification at
http://www.microchip.com/packaging
FIGURE 9-1:
2001-2020 Microchip Technology Inc.
DS00002704C-page 57
Note: For the most current package drawings,
see the Microchip Packaging Specification at
http://www.microchip.com/packaging
COM20020i Rev. D
FIGURE 9-2:
DS00002704C-page 58
COM20020ID 28-PIN PLCC PACKAGE OUTLINE
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
APPENDIX A:
FUNCTION OF NOSYNC AND EF BITS
This appendix describes the function of the NOSYNC and EF bits.
A.1
NOSYNC Bit
The NOSYNC bit controls whether or not the RAM initialization sequence requires the line to be idle by enabling or disabling the SYNC command during initialization. It is defined as follows:
NOSYNC: Enable/Disable SYNC command during initialization. NOSYNC=0, Enable (Default): the line has to be idle
for the RAM initialization sequence to be written, NOSYNC=1, Disable: the line does not have to be idle for the RAM
initialization sequence to be written.
The following discussion describes the function of this bit:
During initialization, after the CPU writes the Node ID, the COM20020iD will write "D1"h data to Address 000h and NodeID to Address 001h of its internal RAM within 6uS. These values are read as part of the diagnostic test. If the D1 and
Node-ID initialization sequence cannot be read, the initialization routine will report it as a device diagnostic failure. These
writes are controlled by a micro-program which sometimes waits if the line is active; SYNC is the micro-program command that causes the wait. When the micro-program waits, the initial RAM write does not occur, which causes the diagnostic error. Thus in this case, if the line is not idle, the initialization sequence may not be written, which will be reported
as a device diagnostic failure.
However, the initialization sequence and diagnostics of the COM20020iD should be independent of the network status.
This is accomplished through some additional logic to decode the program counter, enabled by the NOSYNC bit. When
it finds that the micro-program is in the initialization routine, it disables the SYNC command. In this case, the initialization
will not be held up by the line status.
Thus, by setting the NOSYNC bit, the line does not have to be idle for the RAM initialization sequence to be written.
A.2
EF Bit
The EF bit controls several modifications to internal operation timing and logic. It is defined as follows:
EF: Enable/Disable the new internal operation timing and logic refinements. EF=0: (Default) Disable the new internal
operation timing (the timing is the same as in the COM20020 Rev. B); EF=1: Enable the new internal operation timing.
The EF bit controls the following timing/logic refinements in the COM20020iD:
a)
Extend Interrupt Disable Time
While the interrupt is active (nINTR pin=0), the interrupt is disabled by writing the Clear Tx/Rx interrupt and Clear Flag
command and by reading the Next-ID register. This minimum disable time is changed by the Data Rate. For example,
it is 200 nS at 2.5 Mbps and 100 nS at 5 Mbps. The 100 nS width will be too short to for the Interrupt to be seen.
Setting the EF bit will change the minimum disable time to always be more than 200 nS even if the Data Rate is 5 Mbps.
This is done by changing the clock which is supplied to the Interrupt Disable logic. The frequency of this clock is always
less than 20MHz even if the data rate is 5 Mbps.
b)
Synchronize the Pre-Scalar Output
The Pre-Scalar is used to change the data rate. The output clock is selected by CKP3-1 bits in the Set-Up register. The
CKP3-1 bits are changed by writing the Set-Up register from outside the CPU. It's not synchronized between the CPU
and COM20020iD. Thus, changing the CKP3-1 timing does not synchronize with the internal clocks of Pre-Scalar, and
changing CKP3-1 may cause spike noise to appear on the output clock line.
Setting the EF bit will include flip-flops inserted between the Configuration register and Pre-Scalar for synchronizing the
CKP3-1 with Pre-Scalar’s internal clocks.
Never change the CKP3-1 when the data rate is over 5 Mbps. They must all be zero.
c)
Shorten The Write Interval Time To The Command Register
The COM20020iD limits the write interval time for continuous writing to the Command register. The minimum interval
time is changed by the Data Rate. It's 100 nS at the 2.5 Mbps and 1.6 S at the 156.25 Kbps. This 1.6 S is very long
for CPU.
2001-2020 Microchip Technology Inc.
DS00002704C-page 59
COM20020i Rev. D
Setting the EF bit will change the clock source from OSCK clock (8 times frequency of data rate) to XTAL clock which
is not changed by the data rate, such that the minimum interval time becomes 100 nS.
d)
Eliminate The Write Prohibition Period For The Enable Tx/Rx Commands
The COM20020iD has a write prohibition period for writing the Enable Transmit/Receive Commands. This period is
started by the TA or RI bit (Status Reg.) returning to High. This prohibition period is caused by setting the TA/RI bit with
a pulse signal. It is 3.2 S at 156.25 Kbps. This period may be a problem when using interrupt processing. The interrupt
occurs when the RI bit returns to High. The CPU writes the next Enable Receive Command to the other page immediately. In this case, the interval time between the interrupt and writing Command is shorter than 3.2 S.
Setting the EF bit will cause the TA/RI bit to return to High upon release of the pulse signal for setting the TA/RI bit,
instead of at the start of the pulse. This is illustrated in Figure A-1.
The EF bit also controls the resolution of the following issues from the COM20020 Rev. B:
a)
Network MAP Generation
Tentative ID is used for generating the Network MAP, but it sometimes detects a non-existent node. Every time the Tentative-ID register is written, the effect of the old Tentative-ID remains active for a while, which results in an incorrect network map. It can be avoided by a carefully coded software routine, but this requires the programmer to have deep
knowledge of how the COM20020iD works. Duplicate-ID is mainly used for generating the Network MAP. This has the
same issue as Tentative-ID.
A minor logic change clears all the remaining effects of the old Tentative-ID and the old Duplicate-ID, when the
COM20020iD detects a write operation to Tentative-ID or Node-ID register. With this change, programmers can use the
Tentative-ID or Duplicate-ID for generating the network MAP without any issues. This change is Enabled/Disabled by
the EF bit.
b)
Mask Register Reset
The Mask register is reset by a soft reset in the COM20020 Rev. A, but is not reset in Rev. B. The Mask register is related
to the Status and Diagnostic register, so it should be reset by a soft reset. Otherwise, every time the soft reset happens,
the COM20020 Rev. B generates an unnecessary interrupt since the status bits RI and TA are back to one by the soft
reset.
This is resolved by changing the logic to reset the Mask register both by the hard reset and by the soft reset. The soft
reset is activated by the Node-ID register going to 00h or by the RESET bit going to High in the Configuration register.
This solution is Enabled/Disabled by the EF bit.
DS00002704C-page 60
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
FIGURE A-1:
EFFECT OF THE EB BIT ON THE TA/RI BIT
EF=0
Tx/Rx completed
TA/RI bit
Setting Pulse
nINTR pin
prohibition period
EF=1
Tx/Rx completed
TA/RI bit
Setting Pulse
nINTR pin
2001-2020 Microchip Technology Inc.
DS00002704C-page 61
COM20020i Rev. D
APPENDIX B:
EXAMPLE OF INTERFACE CIRCUIT DIAGRAM TO ISA BUS
ISA Bus
LS688x2
AEN
nG
SA15-SA4
12 bit
Comparators
Q
P
P=Q
12
I/O Address Seeting (DIP Switches)
COM20020I
12
nCS
LS245
A
SD7-SD0
A
16 bit Bus
Transceivers
B
D7-D0
8
8
DIR
nG
nIOR
nRD
nIOW
nWR
SA2-SA0
A2-A0
3
3
IRQm
nINTR
nIOCS16
DRQn
nDACK
TC
nREFRESH
nRESET
RESETDRV
Schmitt-Trigger Buffer
DS00002704C-page 62
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
APPENDIX C:
SOFTWARE IDENTIFICATION OF THE COM20020 REV B, REV C
AND REV D
In order to properly write software to work with the COM20020 Rev B, C and D it is necessary to be able to identify the
different revisions of the part.
To identify the COM20020 Revision follow the following procedure:
1.
2.
3.
Write 0x98 to Register-6 (Address = 6)
Write 0x02 to Register-5 (Address = 5)
Read Register-6
* If the value read from Register-6 is 0x98 then the part is a COM20020 Rev B or earlier
* If the value read from Register-6 is 0x9A then go to next step below
4.
5.
Write 0x80 to Register-5
Read Register-5
* If the value read from Register-5 is 0x00 then the part is a COM20020 Rev C
* If the value read from Register-5 is 0x80 then the part is a COM20020 Rev D
2001-2020 Microchip Technology Inc.
DS00002704C-page 63
COM20020i Rev. D
APPENDIX D:
TABLE D-1:
DATA SHEET REVISION HISTORY
REVISION HISTORY
Revision
Section/Figure/Entry
Correction
DS00002704C (08-10-20)
Section 3.0, "Description of
Pin Functions"
DS00002704B (05-26-20)
• REV A revision history corrected in table
• Updated Sales Listing and Trademark pages
DS00002704A (05-08-18)
REV A replaces SMSC version Rev. 12-05-06.
DS00002704C-page 64
Description for Crystal Oscillator pin updated;
“390W pull-up resistor” changed to “390 pull-up
resistor”.
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
THE MICROCHIP WEB SITE
Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make
files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information:
• Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s
guides and hardware support documents, latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQ), technical support requests, online discussion
groups, Microchip consultant program member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives
CUSTOMER CHANGE NOTIFICATION SERVICE
Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive
e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or
development tool of interest.
To register, access the Microchip web site at www.microchip.com. Under “Support”, click on “Customer Change Notification” and follow the registration instructions.
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales
offices are also available to help customers. A listing of sales offices and locations is included in the back of this document.
Technical support is available through the web site at: http://www.microchip.com/support
2001-2020 Microchip Technology Inc.
DS00002704C-page 65
COM20020i Rev. D
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
[X]
-
Temperature
Range
XXX
Package
Device:
COM20020i
Temperature Range:
i
Package:
HT
=
DZD =
Tape and Reel Option:
Blank
TR
= -40C to
[X](1)
-
Tape and Reel
Option
Examples:
a)
b)
+85C
(Industrial)
48-pin TQFP
28-pin PLCC
c)
COM20020i-HT
Industrial temperature
48-pin TQFP RoHS Compliant package
Tray
COM20020i-DZD
Industrial temperature
28-pin PLCC RoHS Compliant package
Tray
COM20020i-DZD-TR
Industrial temperature
28-pin PLCC RoHS Compliant package
Tape & Reel
Note 1:
= Standard packaging (tray)
= Tape and Reel(1)
Tape and Reel identifier only appears in the
catalog part number description. This
identifier is used for ordering purposes and is
not printed on the device package. Check
with your Microchip Sales Office for package
availability with the Tape and Reel option.
* TQFP package is recommended for new design.
DS00002704C-page 66
2001-2020 Microchip Technology Inc.
COM20020i Rev. D
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device applications and the like is provided only for your convenience and may be
superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO
REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE,
MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold
harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or
otherwise, under any Microchip intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, Adaptec, AnyRate, AVR, AVR logo, AVR Freaks, BesTime, BitCloud, chipKIT, chipKIT logo,
CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, HELDO, IGLOO, JukeBlox, KeeLoq, Kleer, LANCheck, LinkMD, maXStylus, maXTouch,
MediaLB, megaAVR, Microsemi, Microsemi logo, MOST, MOST logo, MPLAB, OptoLyzer, PackeTime, PIC, picoPower, PICSTART, PIC32 logo,
PolarFire, Prochip Designer, QTouch, SAM-BA, SenGenuity, SpyNIC, SST, SST Logo, SuperFlash, Symmetricom, SyncServer, Tachyon,
TempTrackr, TimeSource, tinyAVR, UNI/O, Vectron, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and
other countries.
APT, ClockWorks, The Embedded Control Solutions Company, EtherSynch, FlashTec, Hyper Speed Control, HyperLight Load, IntelliMOS, Libero,
motorBench, mTouch, Powermite 3, Precision Edge, ProASIC, ProASIC Plus, ProASIC Plus logo, Quiet-Wire, SmartFusion, SyncWorld, Temux,
TimeCesium, TimeHub, TimePictra, TimeProvider, Vite, WinPath, and ZL are registered trademarks of Microchip Technology Incorporated in the
U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BlueSky, BodyCom, CodeGuard,
CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM,
ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain,
Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net,
PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher,
SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.
The Adaptec logo, Frequency on Demand, Silicon Storage Technology, and Symmcom are registered trademarks of Microchip Technology Inc. in
other countries.
GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other
countries.
All other trademarks mentioned herein are property of their respective companies.
© 2001-2020, Microchip Technology Incorporated, All Rights Reserved.
ISBN: 9781522465379
For information regarding Microchip’s Quality Management Systems, please visit www.microchip.com/quality.
2001-2020 Microchip Technology Inc.
DS00002704C-page 67
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
Denmark - Copenhagen
Tel: 45-4485-5910
Fax: 45-4485-2829
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
Finland - Espoo
Tel: 358-9-4520-820
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Israel - Ra’anana
Tel: 972-9-744-7705
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
2001-2020 Microchip Technology Inc.
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-72400
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
DS00002704C-page 68
02/28/20