DSC61XXB
Ultra-Small, Ultra-Low Power MEMS Oscillator
Features
General Description
• Wide Frequency Range: 3.5 kHz to 100 MHz
• Ultra-Low Power Consumption: 3 mA/1 µA
(Active/Standby)
• Ultra-Small Footprints
- 1.6 mm 1.2 mm
- 2.0 mm 1.6 mm
- 2.5 mm 2.0 mm
• Frequency Select Input Supports Two
Pre-Defined Frequencies
• High Stability: ±20 ppm, ±25 ppm, ±50 ppm
• Wide Temperature Range
- Automotive: –40°C to +125°C
- Ext. Industrial: –40°C to +105°C
- Industrial: –40°C to +85°C
- Ext. Commercial: –20° to +70°C
• Excellent Shock and Vibration Immunity
- Qualified to MIL-STD-883
• High Reliability
- 20x Better MTF Than Quartz Oscillators
• Supply Range of 1.71V to 3.63V
• Short Sample Lead Time: 3.3V VDD.
Includes frequency variations due to initial tolerance, temp. and power supply voltage.
Input waveform must be monotonic with rise/fall time < 10 ms
Output Disable time takes up to two periods of the output waveform + 200 ns.
For parts configured with OE, not Standby.
Output is enabled if pad is floated or not connected.
Time to reach 90% of target VDD. Power ramp rise must be monotonic.
2019 Microchip Technology Inc.
DS20006155A-page 3
DSC61XXB
ELECTRICAL CHARACTERISTICS (CONTINUED)
Electrical Characteristics: Unless otherwise indicated, VDD = 1.8V –5% to 3.3V +10%, TA = –40°C to +125°C.
Parameters
Sym.
VOH
Min.
0.8 x VDD
Typ.
—
Max.
—
Units
V
Output Logic Levels
VOL
—
—
0.2 x VDD
V
—
1
1.5
ns
—
0.5
1.0
ns
—
1.2
2.0
ns
—
0.6
1.2
ns
—
8.5
—
—
7
—
—
50
70
—
35
60
—
70
—
—
60
—
tRX/tFX
Output Transition Time
Rise Time/Fall Time
tRY/tFY
Period Jitter, RMS
Cycle-to-Cycle Jitter
(Peak)
Period Jitter
(Peak-to-Peak)
Note 1:
2:
3:
4:
5:
6:
7:
8:
JPER
JCy–Cy
JPP
Conditions
Output Logic High, I = 3 mA,
Std. Drive
Output Logic High, I = 6 mA,
High Drive
Output Logic Low, I = –3 mA,
Std. Drive
Output Logic Low, I = –6 mA,
High Drive
DSC61x2
VDD = 1.8V
High Drive,
20% to 80%
CL = 15 pF VDD = 2.5V/3.3V
DSC61x1
VDD = 1.8V
Std Drive,
20% to 80%
CL = 10 pF VDD = 2.5V/3.3V
psRMS
fOUT =
27 MHz
ps
fOUT =
27 MHz
ps
fOUT =
27 MHz
VDD = 1.8V
VDD = 2.5V/3.3V
VDD = 1.8V
VDD = 2.5V/3.3V
VDD = 1.8V
VDD = 2.5V/3.3V
Pin 4 VDD should be filtered with 0.1 µF capacitor.
Not including current through pull-up resistor on EN pin (if configured). Higher standby current seen at
>3.3V VDD.
Includes frequency variations due to initial tolerance, temp. and power supply voltage.
Input waveform must be monotonic with rise/fall time < 10 ms
Output Disable time takes up to two periods of the output waveform + 200 ns.
For parts configured with OE, not Standby.
Output is enabled if pad is floated or not connected.
Time to reach 90% of target VDD. Power ramp rise must be monotonic.
DS20006155A-page 4
2019 Microchip Technology Inc.
DSC61XXB
TEMPERATURE SPECIFICATIONS (Note 1)
Parameters
Sym.
Min.
Typ.
Max.
Units
Conditions
TJ
–40
—
+150
°C
—
Storage Ambient Temperature Range
TA
–55
—
+150
°C
—
Soldering Temperature
TS
—
+260
—
°C
40 sec. max.
Temperature Ranges
Junction Operating Temperature
Note 1:
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dissipation will cause the device operating junction temperature to exceed the maximum +150°C rating. Sustained junction temperatures above +150°C can impact the device reliability.
2019 Microchip Technology Inc.
DS20006155A-page 5
DSC61XXB
2.0
PIN DESCRIPTIONS
The DSC61xxB is a highly configurable device and can be factory programmed in many different ways to meet the
customer’s needs. Microchip’s ClockWorks® Configurator http://clockworks.microchip.com/Timing/ must be used to
choose the necessary options, create the final part number, data sheet, and order samples. The descriptions of the pins
are listed in Table 2-1.
TABLE 2-1:
DSC61XXB PIN FUNCTION TABLE
Pin Number
Pin Name
1
(Note 1)
STDBY
2
GND
3
Output
4
VDD
Note 1:
OE
FS
Description
Output Enable: H = Active, L = Disabled (High Impedance).
Standby: H = Device is active, L = Device is in standby (Low Power Mode).
Frequency Select: H = Output Frequency 1, L = Output Frequency 2.
Ground.
Oscillator clock output.
Power supply: 1.71V to 3.63V.
DSC610xB/1xB/3xB has a 300 kΩ internal pull-up resistor on pin 1. DSC614xB/5xB/7xB has no internal
pull-up resistor on pin 1 and needs an external pull-up or to be driven by another chip.
An explanation of the different options listed in Table 2-1 follows.
2.1
Pin 1
This is a control pin and may be configured to fulfill one
of three different functions. If not actively driven, a
10 kΩ pull-up resistor is recommended.
2.1.1
OUTPUT ENABLE (OE)
Pin 1 may be configured as OE. Oscillator output may
be turned on and off according to the state of this pin.
2.1.2
2.3
Output Buffer Options
The DSC61xx family is available in multiple output
driver configurations.
The standard-drive (61x1) and high-drive (61x2) deliver
respective output currents of greater than 3 mA and
6 mA at 20%/80% of the supply voltage. For heavy
loads of 15 pF or higher, the high-drive option is
recommended.
STDBY
Pin 1 may be configured as Standby. When the pin is
low, both output buffer and PLL will be off and the
device will enter a low power mode.
2.1.3
FREQUENCY SELECT (FS)
Pin 1 may be configured as FS. The output may be set
to one of two pre-programmed frequencies. The output
clock frequencies can only be set to either kHz or MHz.
A combination of kHz and MHz cannot be set.
2.2
Pins 2 through 4
Pins 2 and 4 are the supply terminals, GND and VDD
respectively. Pin 3 is the clock output, programmable to
Standard and High Drive strength settings. Visit
ClockWorks® Configurator to customize your device.
DS20006155A-page 6
2019 Microchip Technology Inc.
DSC61XXB
3.0
DIAGRAMS
tR
tF
VOH
OUTPUT
VOL
tEN
1/fo
tDA
VIH
ENABLE
FIGURE 3-1:
VIL
Output Waveform.
IDD
VDD
0.1μF
4
3
1
2
CL
VDA
FIGURE 3-2:
Test Circuit.
Via to GND Layer
C1
VDD
Enable
FIGURE 3-3:
Output
GND
Via to GND Layer
Recommended Board Layout.
2019 Microchip Technology Inc.
DS20006155A-page 7
DSC61XXB
SOLDER REFLOW PROFILE
.
4.0
ax
cm
se
ax
cm
se
3°
C/
Reflow
Pre-Heat
8 minutes max.
FIGURE 4-1:
ax.
25°C
60-180
Seconds
cm
150°C
60-150
Seconds
/se
.
3°
C/
217°C
200°C
6°C
Temperature (°C)
260°C
20-40
Seconds
Cool
Time
Solder Reflow Profile.
MSL 1 @ 260°C refer to JSTD-020C
Ramp-Up Rate (200°C to Peak Temp)
3°C/sec. max.
Preheat Time 150°C to 200°C
60 to 180 sec.
Time maintained above 217°C
60 to 150 sec.
Peak Temperature
255°C to 260°C
Time within 5°C of actual Peak
20 to 40 sec.
Ramp-Down Rate
6°C/sec. max.
Time 25°C to Peak Temperature
8 minutes max.
DS20006155A-page 8
2019 Microchip Technology Inc.
DSC61XXB
5.0
PACKAGING INFORMATION
5.1
Package Marking Information
4-Lead VLGA*
2.5 x 2.0
XXXXXXX
XXXYYWW
SSS
4-Lead VFLGA*
2.0 x 1.6/1.6 x 1.2
XXXX
SSS
Legend: XX...X
Y
YY
WW
SSS
e3
*
Example
0400000
DCP1834
287
Example
011H
502
Product code or customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
●, ▲, ▼ Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) and/or Overbar (⎯) symbol may not be to scale.
2019 Microchip Technology Inc.
DS20006155A-page 9
DSC61XXB
4-Lead Very Thin Fine Pitch Land Grid Array (ARA) - 1.6x1.2 mm Body [VFLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
A
B
N
(DATUM A)
(DATUM B)
NOTE 1
E
2X
0.05 C
1
2X
2
TOP VIEW
0.05 C
0.10 C
A1
A
C
SEATING
PLANE
4X
(A3)
0.08 C
SIDE VIEW
b2
3X b1
CH
1
2
CH
NOTE 1
0.07
0.03
C A B
C
e1
e1
2
4X L
N
e
BOTTOM VIEW
Microchip Technology Drawing C04-1199A Sheet 1 of 2
DS20006155A-page 10
2019 Microchip Technology Inc.
DSC61XXB
4-Lead Very Thin Fine Pitch Land Grid Array (ARA) - 1.6x1.2 mm Body [VFLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
Dimension Limits
Number of Terminals
N
e
Terminal Pitch
Terminal Pitch
e1
A
Overall Height
Standoff
A1
Substrate Thickness (with Terminals) A3
Overall Length
D
E
Overall Width
b1
Terminal Width
b2
Terminal Width
L
Terminal Length
Terminal 1 Index Chamfer
CH
MILLIMETERS
NOM
MAX
4
1.20 BSC
0.75 BSC
0.79
0.89
0.84
0.00
0.05
0.02
0.20 REF
1.60 BSC
1.20 BSC
0.25
0.30
0.35
0.325
0.425
0.375
0.30
0.40
0.35
0.125
MIN
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package is saw singulated
3. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-1199A Sheet 2 of 2
2019 Microchip Technology Inc.
DS20006155A-page 11
DSC61XXB
4-Lead Very Thin Fine Pitch Land Grid Array (ARA) - 1.6x1.2 mm Body [VFLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
E1
X1
G1
4
Y
C
G2
1
2
(CH)
SILK SCREEN
X2
E2
RECOMMENDED LAND PATTERN
Units
Dimension Limits
Contact Pitch
E1
Contact Pitch
E2
Contact Spacing
C
Contact Width (X3)
X1
Contact Width
X2
Contact Pad Length (X6)
Y
Space Between Contacts (X4)
G1
Space Between Contacts (X3)
G2
Contact 1 Index Chamfer
CH
MIN
MILLIMETERS
NOM
1.20 BSC
1.16 BSC
0.75
MAX
0.35
0.43
0.50
0.85
0.25
0.13 X 45° REF
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-3199A
DS20006155A-page 12
2019 Microchip Technology Inc.
DSC61XXB
4-Lead Very Thin Fine Pitch Land Grid Array (ASA) - 2.0x1.6 mm Body [VFLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
A
B
N
(DATUM A)
(DATUM B)
NOTE 1
E
2X
0.05 C
1
2X
2
TOP VIEW
0.05 C
0.10 C
C
A1
A
SEATING
PLANE
4X
(A3)
SIDE VIEW
b2
3X b1
0.07
0.03
CH
1
0.08 C
2
CH
NOTE 1
C A B
C
e1
e1
2
4X L
N
e
BOTTOM VIEW
Microchip Technology Drawing C04-1200A Sheet 1 of 2
2019 Microchip Technology Inc.
DS20006155A-page 13
DSC61XXB
4-Lead Very Thin Fine Pitch Land Grid Array (ASA) - 2.0x1.6 mm Body [VFLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
Dimension Limits
Number of Terminals
N
e
Terminal Pitch
Terminal Pitch
e1
Overall Height
A
Standoff
A1
Substrate Thickness (with Terminals) A3
Overall Length
D
Overall Width
E
b1
Terminal Width
Terminal Width
b2
Terminal Length
L
Terminal 1 Index Chamfer
CH
MIN
0.79
0.00
0.30
0.40
0.50
-
MILLIMETERS
NOM
6
1.55 BSC
0.95 BSC
0.84
0.02
0.20 REF
2.00 BSC
1.60 BSC
0.35
0.45
0.55
0.15
MAX
0.89
0.05
0.40
0.50
0.60
-
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package is saw singulated
3. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-1200A Sheet 2 of 2
DS20006155A-page 14
2019 Microchip Technology Inc.
DSC61XXB
4-Lead Very Thin Fine Pitch Land Grid Array (ASA) - 2.0x1.6 mm Body [VFLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
X1
4
Y
G2
C
1
2
(CH)
G1
SILK SCREEN
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
E
Contact Pitch
Contact Spacing
C
Contact Width (X4)
X1
Contact Width (X2)
X2
Contact Pad Length (X6)
Y
Space Between Contacts (X4)
G1
Space Between Contacts (X3)
G2
Contact 1 Index Chamfer
CH
MIN
MILLIMETERS
NOM
1.55 BSC
0.95
MAX
0.50
0.40
0.70
1.05
0.25
0.13 X 45° REF
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-3200A
2019 Microchip Technology Inc.
DS20006155A-page 15
DSC61XXB
4-Lead Very Thin Land Grid Array (AUA) - 2.5x2.0 mm Body [VLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
D
A
B
N
(DATUM A)
(DATUM B)
NOTE 1
E
2X
0.05 C
1
2X
0.05 C
2
TOP VIEW
0.10 C
A1
C
A
SEATING
PLANE
(A3)
4X
SIDE VIEW
0.08 C
4X b1
CH
1
2
CH
NOTE 1
0.07
0.03
C A B
C
e1
e1
2
4X L
N
e
BOTTOM VIEW
Microchip Technology Drawing C04-1202A Sheet 1 of 2
DS20006155A-page 16
2019 Microchip Technology Inc.
DSC61XXB
4-Lead Very Thin Land Grid Array (AUA) - 2.5x2.0 mm Body [VLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
Units
Dimension Limits
Number of Terminals
N
e
Terminal Pitch
e1
Terminal Pitch
Overall Height
A
Standoff
A1
Substrate Thickness (with Terminals) A3
Overall Length
D
Overall Width
E
Terminal Width
b1
Terminal Length
L
Terminal 1 Index Chamfer
CH
MIN
0.79
0.00
0.60
0.60
-
MILLIMETERS
NOM
4
1.65 BSC
1.25 BSC
0.84
0.02
0.20 REF
2.50 BSC
2.00 BSC
0.65
0.65
0.225
MAX
0.89
0.05
0.70
0.70
-
Notes:
1. Pin 1 visual index feature may vary, but must be located within the hatched area.
2. Package is saw singulated
3. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
REF: Reference Dimension, usually without tolerance, for information purposes only.
Microchip Technology Drawing C04-1202A Sheet 2 of 2
2019 Microchip Technology Inc.
DS20006155A-page 17
DSC61XXB
4-Lead Very Thin Land Grid Array (AUA) - 2.5x2.0 mm Body [VLGA]
Note:
For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
X
4
Y
C
G2
1
2
(CH)
G1
SILK SCREEN
E
RECOMMENDED LAND PATTERN
Units
Dimension Limits
E
Contact Pitch
Contact Spacing
C
Contact Width (X4)
X
Contact Pad Length (X6)
Y
Space Between Contacts (X4)
G1
Space Between Contacts (X3)
G2
Contact 1 Index Chamfer
CH
MIN
MILLIMETERS
NOM
1.65 BSC
1.25
MAX
0.70
0.80
0.95
0.45
0.13 X 45° REF
Notes:
1. Dimensioning and tolerancing per ASME Y14.5M
BSC: Basic Dimension. Theoretically exact value shown without tolerances.
Microchip Technology Drawing C04-3202A
DS20006155A-page 18
2019 Microchip Technology Inc.
DSC61XXB
APPENDIX A:
REVISION HISTORY
Revision A (January 2019)
• Initial creation of DSC61xxB Microchip data sheet
DS20006155A.
2019 Microchip Technology Inc.
DS20006155A-page 19
DSC61XXB
NOTES:
DS20006155A-page 20
2019 Microchip Technology Inc.
DSC61XXB
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
Examples:
PART NO.
X
X
X
X
X
X – XXX.XXXX
X
Device Pin 1 Output Package Temperature Frequency Revision Frequency Media
Definition Drive
Type
Range
Stability
Strength
Device:
DSC61:
Pin Definition:
Ultra-Small, Ultra-Low Power MEMS
Oscillator
Selection
Pin 1
Internal Pull-Up Register
0
OE
Pull-up
1
STDBY
Pull-up
2
FS
Pull-up
4
OE
None
5
STDBY
None
6
FS
None
Output Drive
Strength:
1
2
Standard
High
Packages:
J
M
H
=
=
=
4-Lead 2.5 mm x 2.0 mm VLGA
4-Lead 2.0 mm x 1.6 mm VFLGA
4-Lead 1.6 mm x 1.2 mm VFLGA
Temperature
Range:
A
L
I
E
=
=
=
=
–40C to +125C (Automotive)
–40C to +105C (Extended Industrial)
–40C to +85C (Industrial)
–20C to +70C (Extended Commercial)
Frequency
Stability:
1
2
3
=
=
=
± 50 ppm
± 25 ppm
± 20 ppm
Revision:
B
=
Revision B
Frequency:
xxx.xxxx = User-Defined Frequency between
001.0000 MHz and 100.0000 MHz
xxxkxxx = User-Defined Frequency between 003.500 kHz
and 999.999 kHz
xxxx =
Frequency configuration code when pin 1 = FS.
Configure the part online through ClockWorks
Media Type:
=
=
T
=
B
=
a) DSC6112JI2B-100.0000:
Ultra-Small, Ultra-Low Power MEMS Oscillator,
Pin 1 = STDBY with Internal Pull-Up, High Drive
Strength, 4-Lead 2.5 mm x 2.0 mm VLGA, Industrial
Temperature, ±25 ppm Stability, Revision B,
100 MHz Frequency, 140/Tube
b) DSC6101HE1B-016.0000T:
Ultra-Small, Ultra-Low Power MEMS Oscillator,
Pin 1 = OE with Internal Pull-Up, Standard Drive
Strength, 4-Lead 1.6 mm x 1.2 mm VFLGA, Extended
Commercial Temperature, ±50 ppm Stability,
Revision B, 16 MHz Frequency, 1,000/Reel
c) DSC6121MI2B-005QB:
Ultra-Small, Ultra-Low Power MEMS Oscillator,
Pin 1 = Freq. Select with Internal Pull-Up, Standard
Drive Strength, 4-Lead 2.0 mm x 1.6 mm VFLGA,
Industrial Temperature, ±25 ppm Stability, Revision B,
Two Frequencies Configured through ClockWorks,
3,000/Reel
Note 1:
Note 1:
Media Type identifier only appears in the
catalog part number description. This
identifier is used for ordering purposes and
is not printed on the device package. Check
with your Microchip Sales Office for package
availability with different media options.
140/Tube (J Package Option)
100/Bag (M & H Package Option)
1,000/Reel
3,000/Reel
Please visit Microchip ClockWorks® Configurator Website to configure the part number for customized frequency. http://clockworks.microchip.com/timing/.
2019 Microchip Technology Inc.
DS20006155A-page 21
DSC61XXB
NOTES:
DS20006155A-page 22
2019 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
The Microchip name and logo, the Microchip logo, AnyRate, AVR,
AVR logo, AVR Freaks, BitCloud, chipKIT, chipKIT logo,
CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo,
JukeBlox, KeeLoq, Kleer, LANCheck, LINK MD, maXStylus,
maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip
Designer, QTouch, SAM-BA, SpyNIC, SST, SST Logo,
SuperFlash, tinyAVR, UNI/O, and XMEGA are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
and other countries.
ClockWorks, The Embedded Control Solutions Company,
EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS,
mTouch, Precision Edge, and Quiet-Wire are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, BodyCom, CodeGuard,
CryptoAuthentication, CryptoAutomotive, CryptoCompanion,
CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average
Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial
Programming, ICSP, INICnet, Inter-Chip Connectivity,
JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi,
motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB,
MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation,
PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon,
QMatrix, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O,
SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total
Endurance, TSHARC, USBCheck, VariSense, ViewSpan,
WiperLock, Wireless DNA, and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
Silicon Storage Technology is a registered trademark of Microchip
Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2019, Microchip Technology Incorporated, All Rights Reserved.
ISBN: 978-1-5224-4095-6
== ISO/TS 16949 ==
2019 Microchip Technology Inc.
DS20006155A-page 23
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Australia - Sydney
Tel: 61-2-9868-6733
India - Bangalore
Tel: 91-80-3090-4444
China - Beijing
Tel: 86-10-8569-7000
India - New Delhi
Tel: 91-11-4160-8631
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Chengdu
Tel: 86-28-8665-5511
India - Pune
Tel: 91-20-4121-0141
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
China - Chongqing
Tel: 86-23-8980-9588
Japan - Osaka
Tel: 81-6-6152-7160
Finland - Espoo
Tel: 358-9-4520-820
China - Dongguan
Tel: 86-769-8702-9880
Japan - Tokyo
Tel: 81-3-6880- 3770
China - Guangzhou
Tel: 86-20-8755-8029
Korea - Daegu
Tel: 82-53-744-4301
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
China - Hangzhou
Tel: 86-571-8792-8115
Korea - Seoul
Tel: 82-2-554-7200
China - Hong Kong SAR
Tel: 852-2943-5100
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
China - Nanjing
Tel: 86-25-8473-2460
Malaysia - Penang
Tel: 60-4-227-8870
China - Qingdao
Tel: 86-532-8502-7355
Philippines - Manila
Tel: 63-2-634-9065
China - Shanghai
Tel: 86-21-3326-8000
Singapore
Tel: 65-6334-8870
China - Shenyang
Tel: 86-24-2334-2829
Taiwan - Hsin Chu
Tel: 886-3-577-8366
China - Shenzhen
Tel: 86-755-8864-2200
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Israel - Ra’anana
Tel: 972-9-744-7705
China - Suzhou
Tel: 86-186-6233-1526
Taiwan - Taipei
Tel: 886-2-2508-8600
China - Wuhan
Tel: 86-27-5980-5300
Thailand - Bangkok
Tel: 66-2-694-1351
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
China - Xian
Tel: 86-29-8833-7252
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
DS20006155A-page 24
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-67-3636
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7288-4388
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
2019 Microchip Technology Inc.
08/15/18