E510KIT

E510 User Manual 1 2 E510 User Manual OVERVIEW This kit is designed for evaluation and development of QT510-based QWheel™ Rotary slider. It includes a fully assembled rotary slider evaluation board, user panel, cables and software. The E510 has a serial interface allowing connection to a PC for control and data viewing via an included USB to SPI adapter and PC software. For more detailed information about this product please refer to the QT510 datasheet. Materials Provided: 1 x White plastic user panel 1 x E510 evaluation board with self-adhesive on one side 4 x Rubber feet 1 x USB-PC cable 1 x USB-SPI adapter with USB-SPI cable to the E510 1 x SPI cable for user connection to a microcontroller 2 x Sample QT510 ICs 1 x CD-ROM with QSlide™ software and USB drivers 1 x User Guide BOARD PREPARATION The E510 eval board can be adhered to plastic, glass, or any other dielectric panel. If you wish to use the supplied user panel, please follow the steps below: 1 Use normal ESD precautions when working with the E510!! 2 Place the user panel face down on a tableTape down the edges of the panel so it cannot move while you work with it. 3 Remove the paper backing from the E510 Board and adhere it to the rear of the user panel. Bend the PCB slightly as shown while smoothing it to remove any air bubbles. Tip: Line up the PCB with the alignment marks on the back of the slider panel. The PCB must be positioned with the connector on the underside of the QWheel™ logo. The Board does allow some flexing, but care must be taken not to bend it too far as this will crack the solder joints. 4 Un tape the user panel from the table and mount the four rubber feet as shown to make the E510 mechanically stable in use. 3 RUNNING THE E510 4 To Run the E510, Please Follow These Steps: 1 IMPORTANT: First install QSlide™ software and USB drivers (see page 10). 2 Make sure the USB adapter box is NOT plugged into your PC at this time. 3 Connect the E510 to the USB box with the red USB-SPI cable 4 Connect the USB adapter to your running PC and wait at least 10 seconds for the USB adaptor to be recognized. The LED on the USB box should illuminate permanently. 5 Run the QSlide™ software (Qslide_V[x].exe) which should be on your desktop or other location where you copied it. See next page for details of Qslide software operation. 6 With your hands far removed from the E510: Click on the FIXED CAL. 7 Slowly move your hand towards the rotor area. The proximity detection status box will indicate when your hand is still several cm away from the panel. 8 Touch the rotor area with a finger. You can either slide your finger around the surface or touch the rotor at any point. When you remove your finger, the last position touched will be locked on the display. Things to Try: — Alter the proximity and detection thresholds using the pull down menus to change the sensitivity to proximity and touch. The higher the threshold, the less sensitive the E510 will become. QSLIDE™ SOFTWARE OPERATION Warning: Disconnecting the USB cable from the PC while QSlide software is communicating with the E510 board may crash the software. Please close the QSlide software before unplugging the USB cable. QSlide software should automatically detect the correct com port; if not, you may need to select the port manually as shown in the picture. Signal Error indicates that the signal has the wrong polarity, usually due to movement of the board. Clicking the Fixed Cal button will resolve the problem. 5 Prox Detection indicates that the board has detected hand at a distance. The Prox value sets the threshold which will cause the chip to register proximity. Lower numbers are more sensitive. Default = 3 Slider Detection indicates that the board is detecting a finger touch. Changing the associated threshold sets the minimum signal change which will cause the board to register a touch detection. Default = 25 Drift Rate sets the adaptive drift compensation rate; the numbers represent seconds per compensation. Default = 5 If the correct port (usually a com port equal to or higher than 3) does not appear, close the program, wait 30 seconds, and try again — Windows may be slow to recognize the USB hardware. QSlide settings When starting QSlide software the previous values of Prox detection, Slider detection and drift rate are loaded. It may be necessary to reset to the default values shown on the next page. Calibration should be performed with the board mounted securely in its intended position and operating environment, and hands at a distance. Once positioned it should be calibrated using the Fixed Cal button. If the board is moved it may need to be re-calibrated. If any status flags are set prior to operation then the calibration should be repeated. Command Return represents the board response byte in HEX. Indication Dial shows the reported position of the touch. This indication does not change when only proximity is detected. It will lock on the last reported position after touch is lifted. SCHEMATIC DIAGRAM 6 C4 CON1 1 2 3 U2 HT7533-1 2 VIN VOUT 3 GND 1 2.2uF 16V Gnd 1 Vin 2 Vout 3 1 VDD C3 SNS3B 5 R25 10k 2.2uF 16V SNS3A 6 5 nc U2 Footprint 4 nc 13 DRDY 5 2 SDO 6 3 /SS 8 9* 10 nc R22 1k R20 1k R21 1k 4k7 11 SDI 47k * Sleep mode The E510 Eval board is not configured to operate the QT510 in Sleep Mode. If you wish operate the QT510 in sleep mode using a microcontroller via CON1 please refer to the board details on page 8. 12 PROX 100nF C5 100nF SNS2B 7 SNS1A 10 R23 4k7 C1 100nF SNS1B 9 VSS 14 R2 15k R3 15k R1 15k R18 15k R17 15k 127 0 R16 15k R15 15k R4 15k SNS2A 8 4 SCLK R26 R19 C2 4* 7 U1 QT510 R24 4k7 E510 QWheel R5 15k R6 15k 85 R14 15k R7 15k R8 15k R13 15k 43 R12 15k R9 15k R11 R10 15k 15k BOARD DETAILS SPI Interface Connector This connector provides all signals and power needed to communicate with the USB adapter or an external host such as a microcontroller. If you wish to connect the E510 to a microcontroller and operate the QT510 in sleep mode you will need to provide in your interface circuit a 1nF capacitor between PROX (CON1 pin 9) and GND, and a 22k Resistor between DRDY (CON1 pin 4) and GND. Refer to the QT510 Datasheet for more information. See Table 1 (next page) for a description of the connector pinout. Voltage Regulator The E510 uses a low drop out regulator to regulate the 5V supply from the USB adapter box to 3.3V. Resistor R25 is used to provide a minimum load on the regulator when the QT510 sleeps between acquisitions; this is necessary for regulator transient stability. Since the QT510 works on a lower voltage (3.3V) than the USB box (5.0V), the signals from the USB box to the E510 must be level shifted down. This is done using resistive dividers consisting of 1K resistors R20, R21 and R22, plus a set of 560 ohm resistors placed in series with the signal lines inside the USB box. Rotary Slider Element The capacitive rotary slider consists of 18 resistors R1...R18 and the copper pads they connect to. Resistors R19, R23 and R24 provide the QT510 with ESD protection. Sampling Capacitors C1 C2 and C5 are the Cs sampling capacitors; increasing their value will increase sensitivity and resolution of measurement, but will also tend to make for a slower response time. 7 8 Figure 1 — Board Layout QT510 IC CON1, Pin # 1 This end Table 1 — Connector (CON1) Pin List Pin Description 1 0V (Ground) 2 +5V power 3 +5V power 4 DRDY—data ready (output) 5 SDO—serial data (output) 6 /SS—slave select (input) 7 SCLK—serial clock (input) 8 SDI—serial data (input) 9 PROX—active high (output) 10 Not connected Rotary Slider Element Mating half for CON1 Molex 51021-1000 PCB LAYERS Top Silkscreen Top Copper 9 10 SOFTWARE INSTALLATION (CD) If you have a Quantum CD-ROM, follow these steps to install QSlide™ software and USB drivers. If you previously installed such drivers, do not install them again. If you experience problems, make sure you have administrative rights (e.g. under XP Pro). Install the QSlide™ Signal Viewing Software To install the QSlide™ viewing software, simply copy the file Qslide_V[x].exe from the supplied CD to your Windows Desktop. The software can be found on the CD in folder D:\SOFTWARE\ (replace D: with the actual drive letter of your CD) Install the USB Drivers Place the CD-ROM in your CD drive. Connect the USB adapter box to the PC using the supplied USB cable. The E510 may be connected (or not). Windows will display the Found New Hardware Wizard for the USB Serial Cable. Select Install the software automatically and click Next. Windows now installs the drivers. Click Finish when prompted. The Found New Hardware Wizard will appear again for the USB Serial Port device. Simply repeat the above steps again. Windows may prompt you to restart your PC at this point; restarting is not necessary. You are now done with the software and driver installation. Go back to page 4. SOFTWARE INSTALLATION (WEB) 11 Follow these steps to install QSlide™ software and USB drivers from www.qprox.com. If you previously installed such drivers, do not install them again. If you experience problems, make sure you have administrative rights (e.g. under XP Pro). Create New Folder C:\QRG-USB Create a new temporary folder to hold the files you are about to download, called C:\QRG-USB Download and Extract the Files Go to www.qprox.com/software and click on the file qrg-usb_drivers.zip and click Save; save the file to C:\QRG-USB. Extract all files inside qrg-usb_driver.zip within folder C:\QRG-USB. Now, download QSlide™ software (Qslide_V[x].exe) but save this to your Windows Desktop. Install the USB Drivers Follow the USB directions on page 10 except: When the Found New Hardware Wizard appears, select Install from a list or specific location. Then, specify the location as C:\QRG-USB and click Next. Windows will now install the drivers. Click Finish when prompted. The Found New Hardware Wizard will appear again for the USB Serial Port device. Simply repeat the above steps again. You may be prompted to restart your PC; restarting is not necessary. You may now delete the temporary folder C:\QRG-USB. You are now done with the software and driver installation. Go back to page 4. 12 Board Will Not Communicate with PC TROUBLESHOOTER Bad SPI or USB Connections Check/replace cables Make sure the board is getting power and USB light is on solid Bad or Conflicting Virtual Comm Port on PC See the Software Installation section - reinstall driver software, or, change the USB-Serial com port number in Device Manager if there is a conflict LED Flashes on USB Adapter (USB box not recognized) Disconnect and reconnect the board and USB adapter, take care to connect the QSlide™ board to the USB adapter first as USB box detects the QSlide™ board on power up. Board will not Calibrate due to noise (failure to calibrate will cause the board to cease communications) See below — Noisy or erratic signal Noisy or Erratic Signal Noisy Power Supply - try a different USB port or PC Cables or Board too Close to Strong Noise Source (such as a power line or switching noise source) Increase the distance from E510 to the noise source Place a grounded metal shield between the noise source and the QSlide™ board QSlide™ Board is not Mechanically Stable Prevent board from moving around Strong RFI from a Transmitter or Adjacent Digital Product Remove the noise source or shield against it Corporate Headquarters North America 1 Mitchell Point Ensign Way, Hamble Southampton SO31 4RF United Kingdom Tel +44 (0)23 8056 5600 Fax +44 (0)23 8045 3939 Email sales1@qprox.com 651 Holiday Drive Bldg. 5 / 300 Pittsburgh, PA 15220 USA Tel 412-391-7367 Fax 412-291-1015 LQ w w w . q p r o x . c o m 13 Copyright © 2004 QRG Ltd All rights reserved Patented and patents pending Development Team: Martin Simmons, Luben Hristov, Samuel Brunet REV 201.141004